JL Audio TR690-TXi User Manual

Stealthbox
®
INSTALLATION GUIDE
SB-N-MURAN/10W1v2, JL AUDIO, Inc 2006
Sheet SKU#011197 Revision1/18/2006 Page 1
for the
(2003-Up Nissan Murano)
This Stealthbox is a product which requires professional installation skills and tools. Please read this installation guide thor­oughly before beginning the project. It will guide you step by step through the installation.Several of the steps in this process may require two people to accomplish.
It is absolutely vital that the enclosure be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly pres­ents two problems: 1) The sub-bass performance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s) and
2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.
Please enjoy your JL Audio Stealthbox responsibly.
STEP 1:
Remove all contents,rubber flooring,
cargo shade and lower the rear seats.
STEP 2:
Open the cargo flooring and hook it to the upper lip of the tailgate opening. Remove the organizer tray, wooden board, factory woofer enclosure, spare tire and the driver’s side cargo pocket cover.
STEP 3:
a)With a Phillips® screw driver,
remove the driver’s side cargo pocket. b)Unsnap the wiring harness that is running
from front to back,on the floor.
STEP 4:
This picture is looking from the back­seats to the tailgate opening,showing the tail­gate sill plate.
To remove the sill plate;Pop out the middle of these three tabs and then pull out the outer piece from the sill plate.
STEP 5:
With a small flat blade; pop out the oval plastic cover of the tailgate sill plate,that is located under the tailgate hook latch.
The sill plate now can be lifted up and removed out of the vehicle.
STEP 6:
Look to the front left of the cargo area for the two factory bolts that are secur­ing a black plate to the floor.
Remove the left side bolt only.
START
HERE
Continued on Next Page
www.jlaudio.com
➔➔
➔➔➔
STEP 7: There is a large L-bracket that is already mounted to the rear of the Stealthbox®.This L­bracket needs to be unmounted, flipped around and remounted. The picture above shows the large L­bracket properly mounted, with the woofer facing down.
STEP 11: To access this mounting location;enter the vehicle via the driver’s side rear passenger door, lift up the flooring that is laying on the second row seat.
Place a supplied 1/4” Flat Washer onto the 8mmx35mmx1.25” Hex Bolt.
Line up the angle bracket mounting hole to the fac­tory bolt hole . Place the bolt assembly through the angle bracket and thread into the factor y bolt hole . Do not tightly secure.
Cont. From
Previous
Page
Continued on Next Page
STEP 8: a)Place a supplied 3/8” lock washer and 3/8” flat washer onto a
3/8”-16x1-1/4” hex bolt. Using this bolt assembly, secure the supplied small L-bracket onto the front of the Stealthbox®,as is in the picture above.
b)With the Stealthbox® placed into the cargo area. Run speaker wire from the amplifier location to the Stealthbox’s® wire terminal and secure.
STEP 12: With Stealthbox loosely mounted in the front, use the rear L-bracket mounting hole as a dr ill guide.
*CAUTION*
Before drilling, make sure that you are not going to be drilling into any gas lines, br ake lines, transmission lines, electrical wir ing or anything else that might cause a reduction in your weekly pay.Always wear eye protection when drilling.
With the use of a 3/8” drill bit and dr ill. Drill out the floor.
STEP 13: With the supplied hardware, place a 3/8” Flat Washer onto the 3/8” hex bolt. Place the bolt assembly through the angle bracket and drilled hole, from inside the vehicle .
From the underside of the vehicle, place a 3/8” Fender Washer ,3/8” Flat Washer,3/8”Lock Washer and the 3/8”-16 Hex Nut onto the pro­truding bolt. Secure tightly.
Now,tightly secure the front mounting bolt assem­bly, from STEP11.
STEP 14: Not pictured:Place the spare tire, hardboard and hold down wing threaded rod back into place.
The picture above is the under side of the driver’s side rear cargo pocket floor, that was removed in STEP2.
Remove the three positing tabs,indicated by the white arrows.
STEP 9: Place the Stealthbox® into position.The speaker terminal needs to face to the front of the vehicle.
Position the factory wiring harness around the out­side of the front right corner of the Stealthbox®.
STEP 10: Tuck the rear of the factory har ness under the right rear corner.The harness needs to pass between the woofer and the rear L-bracket.
*Make sure that the harness is not under the woofer*.
SB-N-MURAN/10W1v2, JL AUDIO, Inc 2006
Sheet SKU#011197 Revision1/18/2006
Page 2
www.jlaudio.com
L-BRACKET FROM STEALTHBOX
VEHICLE'S FLOOR
FLAT WASHER
HEX NUT
HEX HEAD BOLT
FLAT WASHER
FENDER WASHER
LOCK WASHER
Specifications:
Enclosure T ype: Sealed Driver T ype: 10W1v2-4 Nominal Impedance: 4 Cont. Power Handling: 150Watts
JLAudio recommends using a high quality amplifier such as the JLAudio e2150. The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the e2150 when being used to power your Stealthbox®.
Included Hardware:
1) 1/4” USS Flat Washer
1) 3/8”-16x1-1/4” Hex Bolt
2) 3/8” Split Lock Washer
2) #6x3/8” Philip® Head Screws
1) 3/8”-16x1-3/4” Hex Bolt
3) 3/8” Flat Washer
1) 3/8” x 1-1/4” Fender Washer
1) 2”x1-1/4”x1” 3-Hole L-Bracket
1) 3/8”-16 Hex Nut
1) 8mmx35mmx1.25” Hex Bolt
2) Round Dual Lock Fastener
10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111
The JLAudio e2150 is a very versatile audio component. Please consult the owner’s manual for detailed information about installing and tuning this amplifier.
➔➔➔
STEP 15: a) Lower the flooring back into position, from STEP 2.
b) Place the driver’s side floor cargo pocket panel back into place. Pick up the left side of the panel and stand it up on it’s right edge, just r ight of the pair of the
round dual lock fastener
.As shown in
the picture above. c) Mark the under side of the floor panel, of the
location of the
round dual lock fastener
.
STEP 16: a) Flip over the side floor panel. Measure 1-1/2” from the outside left edge to the right.This measurement needs to line up with the round dual lock fastener
position markings
made in STEP 15. Mark the final location. b) With the pair of supplied round dual lock fasten-
er and the pair of #6x3/8” Phillips® screws. Mount the round dual lock fastener to the under side of the floor panel at the markings.
STEP 17: Snap the driver’s side rear cargo pocket cover into place.
SB-N-MURAN/10W1v2, JL AUDIO, Inc 2006
Sheet SKU#011197 Revision1/18/2006 Pag e 3
www.jlaudio.com
Mid/High Frequency Driver Information:
CONGRATULATIONS! INSTALL COMPLETE.
VR690-CXi
VR650-CXi
Front Location Driver Size:
6x9
Applicable JL Audio Products:
TR690-TXi & VR650-CXi
Rear Location Driver Size:
6.5”
Applicable JL Audio Products:
TR,VR & XR650-CXi
Cont. From
Previous
Page
Difficulty Of Installation:
1-1/2”
Loading...