ZyXEL Communications V-250 User Manual
V-250
DECT GAP Phone
User’s Guide
Version 1.01
Edition 1
4/2007
1 LCD Display
V-250 User’s Guide
Off-hook
Battery Strength
3 bars - full charge
2 bars - half charge
1 bar - low power
Handset Number
Assigned to the V250 by the base
station. Use it for
internal calls.
Handset Name
This is
configurable.
Date day/month/year
format
Speaker Mode
Keypad
Locked
Volume Level
I - low volume
II - medium volume
III - high volume
Right Softkey
Function of the right
softkey. Here,
pressing the right
softkey opens the
MENU screen.
Mute
Signal Strength
Blinking - handset not
registered with a base
station or out of range.
On - handset
registered and in range
of a base station.
Time hour/minute
format
12 or 24 hour mode
2
V-250 User’s Guide
2 Quick Reference - Physical Parts
HANDSET
LCD
Left
Softkey
Navigatorleft
Off-hook
Dialing
Numbers
Speaker
Phone
Microphone
Charge
Ter mi nal s
4
16
2
6
8
12
10
14
BASE
3
11
13
15
Earpiece
1
Navigator-up
Right
5
Softkey
Navigator-
7
right
9
On-hook
Enter
Navigator-down
Internal
Call / Flash
Charge
17
LED
3
V-250 User’s Guide
3 Quick Reference - Basic Operations
• Make a call
Lift the V-250 from the charger and press Off-hook (8). Dial
a number. To end the call, place the V-250 on the charger or
press On-hook (9).
• Receive a call
When the V-250 rings, lift the handset or press Off-hook (8).
To end the call, place the V-250 on the charger or press On-
hook (9).
• Make a call using speakerphone
Press Speaker Phone (12). Dial a number. Speak into the
microphone. To switch to earpiece, press Speaker Phone
(12) again. To end the call, place the V-250 on the charger or
press On-hook (9).
• Receive a call with speakerphone
When the V-250 rings, press Speaker Phone (12). Speak
into the microphone. To end the call press On-hook (9).
• Transfer a call to another handset
Press Internal Call (15) during a call. Dial the number of
another handset (1-5) registered with the base station. Press
On-hook (9) when the other party answers.
• Change the earpiece or speakerphone volume
During a call, press Right Softkey (5) to lower/raise the
volume.
• Mute a call
During a call, press and hold Right Softkey (5) for two seconds. You can hear the other caller, but they cannot hear
you.
4
V-250 User’s Guide
4 Install and Charge the Batteries
1
2
5
3
1 Insert the included batteries. Make sure that the polarities
(+/-) are facing the right direction.
2 Slide the back cover closed. You should hear a click.
3 Connect the RJ-11 jack of the included power adaptor
cable to the back of the charger base.
4 Connect the other end of the power cable to a wall socket.
5 Place the handset in the base station for charging.
4.1 Important Notes About Charging the Batteries
Note: Make sure to charge the batteries for 16 hours
before using your V-250 for the first time.
4
5
V-250 User’s Guide
• After initial charging, the power adaptor must remain connected to the main power supply and the base unit with the
main power switched on. It is recommended to leave the
handset charging overnight to ensure the maximum usable
time.
• The batteries should hold their charge for up to 120 hours,
depending on use. The batteries need replacing if the batteries do not hold a charge for more than two hours.
• If the phone is not to be used for a substantial period of time,
for example during holidays, disconnect the main power
adaptor. When power is reconnected it is necessary to
recharge the handset for 16 hours.
5 Basic Setup and Operations
You must have a DECT GAP base station already set up with
a phone connection (VoIP, PSTN or ISDN) to make external
calls (A). You can also use the V-250 to make internal calls
(B).
B
A
6
V-250 User’s Guide
5.1 Register with a Base Station
1 Put your base station in registration mode. On ZyXEL
base stations, press the base station button for 6 to 11
seconds. See your base station documentation for details.
2 Make sure the LCD is on (press any key).
3 Press the Right Softkey to enter the main menu.
4 Navigate to the PHONE SETTING screen by using the
Navigator-right button, then press the Right Softkey to
select OK and enter the PHONE SETTING menu.
5 Use the Navigator-up button to
scroll to REGISTER and press
the Right Softkey to select OK
and enter the base registration
screen.
6 Use the Navigator-up and
Navigator-down buttons to scroll
and select which base station you
want to register with (1-4). You
can register with up to 4 base
stations. Press the Right Softkey
to select OK and enter the screen
to enter the base station PIN
(password).
PHONE SETTING
HS NAME
PAB X
DIRECT CALL
WALLPAPER
SET CONTRAST
REGISTER
DEREGISTER
BACK OK
PHONE SETTING
BASE 1
BACK OK
7
V-250 User’s Guide
7 Use the numbers on the V-250’s
keypad to enter the base station
PIN. This is a 4 digit number you
configure on the base station.
Press the Right Softkey to select
OK and enter the screen to enter
PHONE SETTING
PIN : ****
LONG PRESS BASE
PAGE KEY
the base station PIN (password).
Default on ZyXEL base stations is
1234.
22/11/2006 12:23
BACK OK
Your handset attempts to register
with the base station. Once registration is successful the
Signal Strength indicator stops blinking.
Note: The Signal Strength indicator blinks if the V-250 is
not registered with any base stations or if there are
no base stations within range.
8 After a successful registration the LCD displays the
handset’s internal number and VoIP status.
• Internal Number - “3” here. This
number can be used to call the V250 from other handsets registered
with this base station.
• VOIP OFF/ON - This indicates
whether the base station this
phone is registered with has a VoIP
connection.
3 ZYXEL
VOIP OFF
22/11/2006 12:24
MENU
5.2 Last Number Redial
The V-250 stores the last 10 numbers you dialed in memory.
8
Loading...