ZyXEL Communications ONU5100-B22 User Manual

User’s Guide

ONU5100-B22

2. Press the ONU5100-B22 firmly until it clicks into

place.

EPON ONU SFP Transceiver Module

Version 1.00 Edition 1, 8/2009

Overview

The ONU5100-B22 is an EPON transceiver module that complies with the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA). Installing the ONU5100-B22 in the SFP port on a switch lets the SFP port act as an optical network unit (ONU) that allows you to enjoy high-speed Internet access over optical networks.

Internet

Switch

OLT

ONU

The ONU5100-B22 comes with one fiber port. No configuration is required as all device configuration is done remotely by the OLT (Optical Line Terminal). Once you have connected the hardware, you are ready to access the Internet.

3. The switch with the SFP port automatically detects the installed ONU5100-B22. Check the LEDs to verify that it is functioning properly.

4. Use an SC-type, single-mode optical cable to connect the ONU5100-B22’s PON port and an OLT for Internet access.

Transceiver Removal

Use the following steps to remove the ONU5100-B22 from an SFP port.

1. Remove the fiber optic cable from the ONU5100B22.

2. Open the ONU5100-B22's latch (latch styles vary).

Hardware Installation

You can install or remove the ONU5100-B22 while the switch on which you want to install the ONU5100-B22 is operating.

To avoid possible eye injury, do not look into an operating fiber-optic module's connectors.

Transceiver Installation

Use the following steps to install the ONU5100-B22 in an SFP port.

1. Insert the ONU5100-B22 into an SFP port with the exposed section of PCB board facing down.

3. Pull the ONU5100-B22 out of the port.

Test Your Connection

After you have installed and connected the ONU5100B22 to an OLT, open a web browser on your computer which is connected to the switch on which the ONU5100-B22 is installed and go to any web site (for example, www.zyxel.com) to test your Internet connection.

If you cannot connect to the Internet, make sure the OLT has Internet access and the ONU5100-B22 is registered with the OLT successfully.

If the ONU5100-B22 cannot register with the OLT,

• Check the connector on the optical cable and the PON port. Make sure they are clean and dust-free. Use an air duster to clean the connectors. Do NOT use a wet cloth to clean the connectors.

• Check the optical cable. Make sure it is not broken. If the cable is broken, contact your service provider to have the cable/connector replaced.

Specifications

Specifications are accurate at the time of writing.

Feature Specification

Dimensions (mm) 75 (Wide) x 14 (Deep) x 12.4 (High)

Weight < 1 kg

Power Supply + 3.3V

Power Consumption < 2 W

Case Operation Temperature

Storage Temperature

0 ºC ~ 70 ºC

-40 ºC ~ 85 ºC

ENGLISH

• Use ONLY an appropriate power adaptor or cord for your device.

• Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning.

• Make sure that the cable system is grounded so as to provide some protection against voltage surges.

Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately.

Feature Specification

Operation Humidity 0% ~ 85% (non-condensing)

Storage Humidity 0% ~ 95% (non-condensing)

PON Interface One PON port (single fiber link)

Compliant with IEEE 802.3ah PX-20 SC optical connectors with shutters Transmission distance: 20 km Wavelength: 1310 nm upstream and 1490 nm downstream Full duplex

Safety Warnings

• Ground yourself (by properly using an anti-static wrist strap for example) whenever working with the device's hardware or connections.

• Do NOT use this product near water, for example, in a wet basement or near a swimming pool.

• Do NOT expose your device to dampness, dust or corrosive liquids.

• Do NOT store things on the device.

• Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning.

• Connect ONLY suitable accessories to the device.

• Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information.

• Make sure to connect the cables to the correct ports.

• Place connecting cables carefully so that no one will step on them or stumble over them.

• Always disconnect all cables from this device before servicing or disassembling.