ZTE ZXW3614B User Manual

Outdoor Wireless Access Point
ZTE CORPORATION NO. 55, Hi-tech Road South, ShenZhen, P.R.China Postcode: 518057 Tel: (86) 755 26770801 URL: http://ensupport.zte.com.cn E-mail: support@zte.com.cn
ZXV10 W615
User Manual
Verson: V3.0
LEGAL INFORMATION
Copyright © 2010 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation.
The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice.
Version No. : RVerson: V3.0 Edition Time : 2012-08-20(R1.0) Manual No. : SJ-20120820095015-001
C h a p t e r 1
Product Introduction
ProductOverview
The ZTE ZXV10 W615 broadband wireless access product operates at 2.4 GHz, 5.2 GHz and 5.8 GHz frequency bands and complies with IEEE 802.11a,
802.11b, 802.11g, and 802.11n protocols. The device adopts the Orthogonal Frequency Division Multiplexing (OFDM) technology. Featuring a transmission speed of up to 300 Mbps, high receiving sensitivity, and long transmission distance, it provides a powerful wireless access solution for telecommunication operators, Internet Service Provider (ISP) and other enterprises.
By supporting multiple encryption mechanisms and authority management functions, the ZXV10 W615 provides a highly secure system for Wireless Local Area Network (WLAN).
By supporting Power over Ethernet (PoE), ZXV10 W615 acquires convenient power supply.
TypicalApplication
The device is typically used in the following scenarios:
Small and medium-sized enterprises
To realize wireless coverage and meet mobile office requirements.
Remote access to the company network.
To receive and send E-mails, transmit files, emulate terminals, and others. The device supports various wireless network connection modes, such as point-to-point connection, single access point connection, multiple access point connection, and roaming. It can apply to various application environments, such as connection within an Intranet and between different networks.
An environment where it is difficult to establish a connection through
network cables To be used in places where cabling is difficult, such as an old building and
Confidential and Proprietary Information of ZTE CORPORATION 1
ZXV10 W615 User Manual
an asbestos building structure.
Mobile office system
To be used by retailers, manufacturers and in the working site which needs to be changed frequently.
Temporary LAN establishment for a special project
To be used when a LAN needs to be established temporarily in places such as commercial exhibitions, exhibition halls and construction sites; when the capacity needs to be expanded during peak hours in places such as retailing shops, airports and airlines; or when the financial auditor needs to establish a client work group.
Access to the database by mobile workers
To enable doctors, nurses and retailers to share information through mobile access to the database.
Family office users
To meet the requirement for installing a small computer network easily and quickly.
InterfaceandButtonDescription
For a description of the interfaces and buttons of the ZXV10 W615, refer to the following table:
Name Description
Ethernet LAN interface/PoE (supports 10/100/1000 Mbps), connected by an
RJ-45 network cable.
2.4G-A 2.4G antenna interface, used to connect an antenna.
2.4G-B 2.4G antenna interface, used to connect an antenna.
5G-A 5G antenna interface, used to connect an antenna.
5G-B 5G antenna interface, used to connect an antenna.
WAN/PoE RJ-45 interface, used for uplink connection and supplying power.
GND Grounding terminal.
TechnicalSpecifications
Physical Specification
Size: 210 mm×210 mm×69 mm (Length × Width × Height)
Weight: 4 kg
Electric Parameters
Power supply: 802.3at PoE+
2 Confidential and Proprietary Information of ZTE CORPORATION
Voltage: -48 VDC
Maximum power consumption: 18 W
Environment Requirement
Working temperature: -40 ℃ to 65
Working humidity: 5 %RH to 100 %RH
IP Protection Class
IP protection class: IP66
Passed Certifications
CCCiWi-FiRoHS ZTE Corporation reserves the right to modify technical parameters with this
manual without notice.
Antenna Requirement
ZXV10 W615 User Manual
Antenna Type: N-type Dipole Antenna
Frequency (MHz) Gain(dBi)
2400 1.0 2410 1.2 2420 1.1 2430 1.2 2440 0.9 2450 1.0 2460 1.1 2470 1.0 2480 1.2 2490 1.4 2500 1.1 5220 2.98 5765 3.43
Confidential and Proprietary Information of ZTE CORPORATION 3
C h a p t e r 2
Configuration Preparation
Login
The ZXV10 W615 supports configuration based on Web pages. You can configure and manage the ZXV10 W615 through a Web browser.
Open the Internet Explorer, type http://192.168.0.228 on the address bar, and then press Enter. The login dialog box is displayed, see the following figure.
Enter a valid user name and a password, and then click Login. The Web configuration page of the ZXV10 W615 device is displayed.
Notes:
The initial user name and password of a common user are both user. This user has only the authority to view the related Status information of this device. The initial user name and password of the administrator are both admin. This user has the authority to configure and manage the device through the Web browser.
For the factory defaults of ZXV10 W615, refer to the following table:
Item Default Value
IP Address/Mask of Ethernet interface
User name/Password
Confidential and Proprietary Information of ZTE CORPORATION 4
IP address: 192.168.0.228 Subnet mask: 255.255.255.0
Initial user name/password for common user: user/user Initial user name/password for administrator:
admin/admin
ZXV10 W615 User Manual
Item Default Value
AP mode Fit AP
AP name APxxxxxxxxxxxx, where xxxxxxxxxxxx means the
Medium Access Control (MAC) address of the device
AC discovery mode Dynamic Host Configuration Protocol (DHCP),
applicable for fit AP only.
WAN mode DHCP
Wireless mode
Network card 1: Mixed (802.11b+802.11g)
Network card 2: Mixed (802.11a+802.11n)
SSID SSID1 is enabled.
IntroductiontotheGUIforSoftwareSetup
After log in, the software interface is displayed as Figure 1.
Figure 1 Software Interface
1. Main menu
2. Submenu
3. Parameter
Select items on the main menu for software setup. Select sub-items to set parameters on the left submenu.
Confidential and Proprietary Information of ZTE CORPORATION 5
ZXV10 W615 User Manual
Notes:
Click Logout at the upper-right corner of the current Web page. Then,
the system log outs and returns to the Login page.
Click at the bottom of the navigation pane to view the related
help information on the current page.
Click the Help tab to open the Help page to view the related help
information.
Click at the top of the current web page to change the language
to chinese.
6 Confidential and Proprietary Information of ZTE CORPORATION
C h a p t e r 3
Device Status
CheckingDeviceInformation
This section describes how to check the device information.
Steps
Select Status > Device Information to open the Device Information page.
Device information is displayed on the Device Information page as Figure
2.
Figure 2 Device Information
Notes:
This page includes the information of model, serial no, batch number, hardware version, software version, boot loader version and AP name.
—END OF STEPS—
Confidential and Proprietary Information of ZTE CORPORATION 7
Steps
ZXV10 W615 User Manual
CheckingInformationofNetworkInterfaces
Checking Ethernet Interface Information
This section describes how to check Ethernet interface information.
Select Status > Network Interface > Ethernet, the following page with
Ethernet interface information is displayed.
Figure 3 Ethernet Interface Information
Steps
Notes:
This page includes Ethernet port, MAC address, status, mode,
packets received/bytes received, and packets sent/bytes sent information.
You can click Refresh to view the latest Ethernet interface
information.
—END OF STEPS—
Checking WAN Connection
This section describes how to check the network connection information.
Select Status > Network Interface > WAN Connection., the following page
with the established connection information is displayed.
8 Confidential and Proprietary Information of ZTE CORPORATION
ZXV10 W615 User Manual
Figure 4 WAN Connection Information
Steps
Notes:
This page includes DHCP, WAN MAC, NAT(Network Address
Translation), IP, DNSDomain Name Server), Gateway, Connection status, remaining lease time.
You can click Refresh to view the latest WAN connection
information.
—END OF STEPS—
CheckingWLANInterfaceInformation
This section describes how to check the WLAN interface information.
Select Status > User Interface > WLAN, the following page is displayed. In
the right pane, view the WLAN interface information.
Confidential and Proprietary Information of ZTE CORPORATION 9
ZXV10 W615 User Manual
Figure 5 WLAN Interface Information
Notes:
This page includes the wireless switch state, the channel, the WDS
mode (if the WDS is enabled, the MAC address of the WDS interface, the MAC address of the relay/the root AP and the connection state is displayed) and the SSID enabled state.
You can click Refresh below the drop-down scroll bar (It isn’t
displayed in the above figure for the limitation on the figure size) to view the latest device information.
—END OF STEPS—
10 Confidential and Proprietary Information of ZTE CORPORATION
C h a p t e r 4
Network Configuration
BroadbandConnectionConfiguration
Configuring a Broadband Connection (Fit AP)
The ZXV10 W615 has two operational modes: fat AP and fit AP. The default operational mode is fit AP.
Context
Steps
For instructions on how to change the AP mode for the ZXV10 W615, refer to “Setting the AP Mode”.
Notes:
After the AP mode is changed, the device restarts automatically.
1. Select Network > WAN > WAN Connection. The following page is
displayed.
Confidential and Proprietary Information of ZTE CORPORATION 11
ZXV10 W615 User Manual
2. Configure the parameters. Refer to the following table.
Parameter Description
IP Version Supported protocol versions include Internet Protocol
version 4 (IPv4), Internet Protocol version 6 (IPv6), and IPv4/v6. The default setting is IPv4.
AC Discovery Mode Includes DHCP, Static, DNS, and Broadcast. The default
setting is DHCP.
AC Type Set AC Type. When AC Type is set to Adapter, the AP
selects the uplink AC automatically.
AC Name This parameter is configurable when AC Discovery Mode
is DHCP or DNS.
Enable CAPWAP Encryption
WAN Type When IP Version is IPv4, the supported modes are
Enables or disables CAPWAP encryption.
DHCP, Static, and PPPoE. When IP version is IPv6 or IPv4/v6, the supported modes are DHCP and PPPoE. The default mode is DHCP. When AC Discovery Mode is DHCP, the WAN mode is set to DHCP.
12 Confidential and Proprietary Information of ZTE CORPORATION
ZXV10 W615 User Manual
Parameter Description
Enable Verify AC Enables or disables the AC verification function when
WAN Type is DHCP.
Enable VLAN Enables or disables the VLAN configuration function.
Virtual Local Area Network (VLAN) Identification/Identity/Identifier (ID) and 802.1p are used to set the VLAN and priority for the selected device.
VLAN ID Indicates the VLAN ID of packets through the WAN
interface. The value range is 0-4094.
802.1p Specifies the processing priority. It only applies to multiple WAN connections. The range is 0-7 and the default value is 0, which means no priority. A greater value indicates a higher priority.
Enable DSCP Enables or disables the Differential Services Code Point
(DSCP) function for data flow.
DSCP Specifies the DSCP value. The value range is 0-63.
MTU Specifies the Maximum Transmission Unit (MTU) value.
The default value is 1448.
Steps
3. Click Submit.
Notes:
The configuration on this page takes effect after the device is restarted.
—END OF STEPS—
Configuring a Broadband Connection (Fat AP)
This section describes how to configure a broadband connection for fat AP.
The AP mode of the device is Fat.
1. Select Network > WAN > WAN Connection. The following page is
displayed.
Confidential and Proprietary Information of ZTE CORPORATION 13
ZXV10 W615 User Manual
2. Configure the parameters. For details, refer to “Configuring a Broadband
Connection (Fit AP)”.
Working Mode: supports Bridge mode and Route mode. The default is
Bridge mode.
WAN Type: When IP Version is IPv4, the supported modes are DHCP,
Static, and PPPoE. When IP version is IPv6 or IPv4/v6, the supported modes are DHCP and PPPoE. The default mode is DHCP.
3. Click Submit.
Notes:
The configuration on this page takes effect after the device is restarted.
—END OF STEPS—
WLANConfiguration
Context
Setting Basic Information
This section describes how to set WLAN information for the ZXV10 W615.
Two network cards are available. You can set the cards respectively.
14 Confidential and Proprietary Information of ZTE CORPORATION
Steps
Network card 1: works at 2.4 GHz, and supports 802.11b, 802.11g, and
ZXV10 W615 User Manual
802.11n.
Network card 2: works at 5.8 GHz, and supports 802.11a and 802.11n.
1. Select Network > WLAN > Basic. The following page is displayed.
2. Confiture the basic parameters of WLAN.
If Network Card 1 is selected, see the previous figure for the configuration page. For a description of the parameters, refer to the following table.
Parameter Description
Network Card Select network card 1.
Enable Wireless RF Enables or disables the wireless RF function
Enable Isolation Enables or disables the SSID isolation function.
Mode Supports IEEE 802.11b Only, IEEE 802.11g Only, IEEE
802.11n Only, Mixed(802.11b+802.11g), Mixed(802 .11g+802.11n),and Mixed(802.11b+802.11g+802.11n).
Confidential and Proprietary Information of ZTE CORPORATION 15
ZXV10 W615 User Manual
Parameter Description
Country/Region United States of America.
Band 2.4 G
Band Width The options are 20 MHz, 40 MHz, and automatic.
MIMO The options are 1*1, 1*2, 2*1, and 2*2.
11N Rate Specifies the transmission rate of 802.11n. 17 rates are
available and the default is Auto.
Transmit Rate Supports various kinds of transmitting rates including1
Mbps 2 Mbps 5.5 Mbps、 11 Mbps 6 Mbps 9 Mbps、 12 Mbps、 18 Mbps、 24 Mbps、 36 Mbps、 48 Mbpsand 54 Mbps
Channel Proper channel can be selected according to country code.
It can be selected as Auto or any value in the range of 1-11. The default is Auto. The channel used to accomplish communication between AP and wireless station is determined by local policy. All wireless stations which communicate with the ZXV10 W615 must use the same channel.
Only Select Channel 1/6/11
Determines whether to select channel 1/6/11 or select all channels.
Total Maximum Clients Specifies the maximum number of connected users. The
range is 1-512.
SGI Enable Enables or disables the SGI function.
A-MPDU Enable Enables or disables the A-MPDU function.
Beacon Interval Specifies the beacon interval.
Power Type Supports configuration by percent, configuration based on
actual power value (unit: dBm), and configuration based on actual power value (unit: mW)
Transmitting Power Supports automatic, 100%, 90%, 80%, 70%, 60%, 50%,
40%, 30%, 20%, 12.5%, and 10%. The default is 100%. The power class refers to the percentage of output power to maximum power. A higher power indicates a farther transmission distance.
QoS Type The options are disabled, WMM, and SSID.
RTS Threshold Specifies the upper limit of transmission request.
DTIM Interval Specifies the DTIM time patch.
WIDS Mode The options are Access, Monitor, and Mixed.
WIDS Scan Period Specifies the value of WIDS scan interval.
WIDS Scan Mode The options are Current Channel and All Channel.
Protection Mode The options are None, CTS Only, and RTS/CTS.
Application Scenarios Support three kinds of application scenarios: low density,
high density, user configuration.
5G Access First Enables or disables 5G access in precedence.
16 Confidential and Proprietary Information of ZTE CORPORATION
ZXV10 W615 User Manual
Parameter Description
TxBF Enable Enables or disables beam forming technology.
If Network card 2 is selected, see the figure below for the configuration page. For a description of the parameters, refer to the following table.
Parameter Description
Network Card Select network card 2.
Enable Wireless RF Enables or disables the WLAN RF function.
Enable Isolation Enables or disables the SSID isolation function.
Mode Supports IEEE 802.11a Only, IEEE 802.11n Only, and
Mixed(802.11a+802.11n). The default is Mixed(802.11a+802.11n).
Country/Region United States of America.
Band 5G
Band Width The options are 20 MHz, 40 MHz, and automatic.
Confidential and Proprietary Information of ZTE CORPORATION 17
ZXV10 W615 User Manual
Parameter Description
MIMO The options are 1×1, 1×2, 2×1, and 2×2.
11N Rate Specifies the transmission rate of 802.11n, supporting
seven rate types.
Channel Proper channel can be selected according to country code.
It can be selected as Auto, 149, 153, 157, 161, or 165. The default is Auto. The channel used to accomplish communication between AP and wireless station is determined by local policy. All wireless stations which communicate with the ZXV10 W615 must use the same channel.
Total Maximum Clients Specifies the maximum number of connected users. The
range is 1-512.
SGI Enable Enables or disables the SGI function.
A-MPDU Enable Enables or disables the A-MPDU function.
Beacon Interval Specifies the beacon interval.
Power Type Supports configuration by percent, configuration based on
actual power value (unit: dBm), and configuration based on actual power value (unit: mW)
Transmitting Power Supports automatic, 100%, 90%, 80%, 70%, 60%, 50%,
40%, 30%, 20%, 12.5%, and 10%. The default is 100%. The power class refers to the percentage of output power to maximum power. A higher power indicates a farther transmission distance.
QoS Type The options are Disabled, WMM, and SSID.
RTS Threshold Specifies the upper limit of transmission request.
DTIM Interval Specifies the DTIM time patch.
WIDS Mode The options are Access, Monitor, and Mixed. The default
is Access.
WIDS Scan Period Specifies the value of WIDS scan interval.
WIDS Scan Mode The options are Current Channel and All Channel.
Protection Mode The options are None, CTS Only, and RTS/CTS.
Application Scenarios Support three kinds of application scenarios: Low density,
High density, User configuration.
5G Access First Enables or disables 5 G access in precedence.
TxBF Enable Enables or disables beam forming technology.
Steps
3. Click Submit.
—END OF STEPS—
Setting SSID
This section describes how to set SSID.
18 Confidential and Proprietary Information of ZTE CORPORATION
ZXV10 W615 User Manual
1. Select Network > WLAN > SSID Settings. The following page is
displayed.
2. Configure the parameters. Refer to the following table.
Parameter Description
Choose SSID Specifies the SSID to be configured. The range is from
SSID1 to SSID32.
Network Card Displays the wireless network card of the current
SSID. SSID1–SSID16 correspond to network card 1. SSID17–SSID32 correspond to network card 2.
Hide SSID Determines whether to hide this SSID.
Enable SSID Enables or disables this SSID.
Enable SSID Isolatio n Enables or disables the isolation within this SSID.
Isolation Mode Specifies an appropriate isolation mode from four
modes, which are Unicast, Broadcast, Multicast, and ALL. The default setting is ALL.
Maximum Clients Specifies the maximum number of clients allowed for
this SSID. The value range is 1–512. The default is 32.
SSID Name Specifies the name of this SSID. The number of
characters is in a range of 1–32.
Confidential and Proprietary Information of ZTE CORPORATION 19
Steps
ZXV10 W615 User Manual
Parameter Description
Priority Specifies the SSID priority . The range is 0–7. The
default value is 0, which means no priority. A greater value indicates a higher priority.
VLAN ID VLAN tag of data packets. VLAN ID can be set in a
range of 0-4094.
802.1p Specifies the processing priority. The range is 0–7. The default value is 0, which means no priority. A greater value indicates a higher priority.
As Management SSID Disabled by default. When this function is enabled, the
user associated with the SSID can manage the device.
3. Click Submit.
—END OF STEPS—
Setting Security Information
This section describes how to set WLAN security information.
1. Select Network > WLAN > Security. The following page is displayed.
2. Configure the parameters. Refer to the following table.
20 Confidential and Proprietary Information of ZTE CORPORATION
ZXV10 W615 User Manual
Parameter Description
Choose SSID Specifies the SSID to be configured. The range is
SSID1-SSID15.
Authentication Type Supports Open System, Shared Key, Open System &
Shared Key, WPA-PSK, WPA2-PSK, WPA/WPA2-PSK, WPA-EAP, WPA2-EAP, WPA/WPA2-EAP, WAPI-PSK, WAPI-CERT, and WEP-EAP.
WPA Passphrase Specifies the WPA encryption key. The range is 8-63
characters.
Enable WPA Group Key Update
WPA Group Key Update Interval
Enables or disables WPA group key updating function. It is enabled by default.
Specifies the key updating interval. The default is 600 seconds.
WPA Encryption Algorithm Supports TKIP, AES, and TKIP+AES.
Authentication Type is divided into non-encryption, WPA-PSK encryption, WPA-EAP encryption, WEP encryption, WAPI-PSK encryption and WAPI-CERT encryption.
non-encryption
Authentication Type selects Open System, meaning non-encryption.
WPA-PSK encryption
WPA encryption means Wi-Fi protected access. It has three modes: WPA-PSK, WPA2-PSK, and WPA/WPA2-PSK.
i. In the Authentication Type drop-down list, select WPA-PSK,
WPA2-PSK, or WPA/WPA2-PSK to enable WPA-PSK encryption.
ii. Set the parameters as required by referring to the parameter description
in the previous table.
WPA-EAP encryption
i. In the Authentication Type drop-down list, select WPA-EAP,
WPA2-EAP, or WPA/WPA2-EAP to enable WPA-EAP encryption.
Confidential and Proprietary Information of ZTE CORPORATION 21
ZXV10 W615 User Manual
ii. Configure the parameters. Refer to the following table.
Parameter Description
Server Type Specifies the server type. The options are Master Auth
Server, Master Acct Server, Backup Auth Server, and Backup Acct Server. The default is Master Auth Server.
Server IP Address Specifies the IP address of the authentication server, for
example, 192.168.1.1.
Server Port Specifies the port of the authentication server, for
example, 1812. The range is 0 to 65535.
Secret Specifies the WPA-EAP encryption key. The range is
1-64 characters.
Reauth Period The default is 3600 seconds.
Enable Preauth Enables or disables the pre-authentication function. The
function is disabled by default.
Enable WPA Group Key Update
WPA Group Key Update Interval
Enables or disables WPA group key updating function. The function i s enabled by default.
Specifies the interval of WPA group key update. The default is 600 seconds.
WPA Encryption Algorithm Specifies the WPA encryption algorithm. Three options
22 Confidential and Proprietary Information of ZTE CORPORATION
ZXV10 W615 User Manual
Parameter Description
are available: AES, TKIP, and TKIP+AES. The default is TKIP.
WEP encryption
Wired Equivalent Privacy (WEP) is a commonly used WLAN security protocol.
i. Select Shared Key or Open System & Shared Key for Authentication
Type. The following page is displayed.
ii. Configure the parameters. Refer to the following table.
Parameter Description
WEP Encryption Enables or disables WEP encryption function. The
function is enabled by default.
WEP Encryption Level There are two types of WEP key, namely 64bit and
128bit.
WEP Key Index Specifies corresponding key value.
Confidential and Proprietary Information of ZTE CORPORATION 23
ZXV10 W615 User Manual
Parameter Description
WEP Key 1–4 Specifies WEP encryption key value. 64-bit WEP key
corresponds to five ASCII characters or ten hexadecimal characters. 128-bit WEP key corresponds to 13 ASCII characters or 26 hexadecimal characters.
WAPI-PSK encryption
i. Select WAPI-PSK as the Authentication Type. The following page is
displayed.
ii. Configure the parameters. Refer to the following table.
Parameter Description
WAPI Key Mode Supports two modes: ASCII and HEX. The default is
ASCII.
WAPI Key Spe cifies WAPI key value. The range is 8-64
characters.
WAPI-CERT encryption
i. Select WAPI-CERT as the Authentication Type. The following page
is displayed.
24 Confidential and Proprietary Information of ZTE CORPORATION
ZXV10 W615 User Manual
ii. Enter the certificate server IP address and certificate server port. iii. Click the Certificate Uploading button, select the proper type of
certificate file in the displayed dialog box, and then click Upload.
Notes:
Certificate files include AS certificate, AP certificate, and CA certificate. If only AP and CA certificates are necessary, upload the AP certificate first. Otherwise, upload the AS certificate first.
WEP-EAP encryption
i. Select WEP-EAP as the Authentica tion Type. The following page is
displayed.
Confidential and Proprietary Information of ZTE CORPORATION 25
Loading...
+ 62 hidden pages