All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in
any form or by any means, electronic or mechanical, including photocopying and
microfilm, without the prior written permission of ZTE Corporation.
ZTE Corporation reserves the right to make modifications on print errors or update
specifications in this manual without prior notice.
Thank you for choosing AC8720 CDMA2000 1X Wireless USB Modem (hereinafter
referred to as USB Modem) of ZTE Corporation.
The USB Modem equips with a standard USB interface and supports CDMA2000
1X network. In the area where there is signal, it allows you to go surf the Internet,
send & receive short messages, and make & receive phone calls.
The USB Modem adopts two designing options: R-UIM and Built-in UIM, which
make your operation more flexible.
The pictures in this guide are only used to demonstrate your USB Modem’s
functions, so they are maybe different from what you see on your USB Modem.
Please refer to your USB Modem if they are differences.
2. Precautions
●Use the original accessories or those authenticated by the manufacturer.
Using any unauthenticated accessories may affect the USB Modem’s
performance, violate the warranty provisions or relevant national regulations
about telecom terminals, or even cause body injury.
●Do not disassemble, modify, frequently pull/plug the antenna, stretch, rotate
or bend the antenna with great force.
●Before pulling out the USB Modem, please use Windows safely removing
the hardware and make sure to exit the application. Do not directly pull out
1
the terminal to avoid the damage of USB Modem or the influence on the
normal operation of operating system.
●Do not forcefully plug/pull the USB Modem to avoid the damage of
connector.
●Do not use your USB Modem near weak signal or high-precision electronic
devices. Radio wave interference may cause misoperation of electronic
devices or other problems.
●Turn off your USB Modem on airplane where it’s forbidden to use it. The
USB Modem may affect the normal operation of electronic devices,
therefore please follow the relevant regulations when using your USB
Modem on airplane.
●Turn off your USB Modem in hospital where it’s forbidden to use it. The USB
Modem may affect the normal operation of medical apparatus, therefore
please follow the relevant regulations when using your USB Modem in
hospital.
●Please do not use the USB Modem near flammable or explosive materials;
otherwise it might cause failure or fire.
●Keep your USB Modem away from water. This may cause overheating or
failure if water or any other kind of liquid enters your USB Modem. Please
do not use your USB Modem near high temperature, damp or dusty place.
●Keep your USB Modem away from children to avoid shock, plunge or
impact. It may cause body injury when the USB Modem is used as a toy.
2
3. Appearance
3.1 Introduction
3
3.2 Operation Guide of Data Cable
Generally, the USB Modem could be directly connected with USB port. You could
also connect the USB Modem with PC by using the accompanying data cable, as
shown in the following figure. Connect Interface with USB Modem, and interface
with PC's USB port. If the power supply from USB port is insufficient, connect both
interface and with USB port together.
4. Install and Uninstall
4.1 System Requirements
The USB Modem supports the following operating system:
Windows 2000/XP/Vista/7
MAC
4
PC minimum configurations:
CPU Pentium-II/233MHz
USB interface 2.0 (USB1.0 and 1.1 compatible)
Optical Drive CD-ROM (for installation only)
Memory 64 MB
Disk Space 50 MB (used for installation of application)
4.2 Installation
Take Windows XP as an example.
1. Please connect USB Modem to PC through USB interface. You could also use
data cable to connect.
2. The installation will automatically start. Please follow installation wizard.
3. The system will automatically find new hardware and install the driver. Wait for
a while. Click “Finish” to complete installation.
4.3 Uninstallation
1. Select Start Programs (Appropriate Uninstall), and system will prompt you to
confirm whether you want to remove the program. Click “Yes” to uninstall.
2. Please wait and then click “OK” to complete uninstall.
5
5. Run the Application
After the application is installed successfully, the application icon will appear on
your desktop. Double-click this icon or select from StartPrograms
(Appropriate Application). Run the application to display the user interface.
The icons on the interface are used to access the function, which indicate as
below:
Open URL
Call Log
NetConnect
Log
Help
6
Service
SMS
Phonebook
Voice Call
NetConnect
Settings
Loading...
+ 21 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.