ZTE AC8716 Users Manual

CDMA2000 1X EV-DO Wireless Data Terminal User Guide
CDMA2000 1X EV-DO
Wireless Data Terminal
User Guide
ZTE Corporation http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
Copyright Statement
Copyright © 2009 by ZTE Corporation
All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. ZTE Corporation reserves the right to make modifications on print errors or update specifications in this manual without prior notice.
ZTE Corporation http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
Table of Contents
1. Introduction.............................................................................................................................1
2. Precautions..............................................................................................................................1
3. Appearance.............................................................................................................................2
3.1 Introduction.........................................................................................................................2
3.2 Insert R-UIM Card..............................................................................................................2
3.3 Operation Guide of Data Cable...........................................................................................3
4. Install and Uninstall................................................................................................................4
4.1 System Requirements..........................................................................................................4
4.2 Installation Guide...............................................................................................................4
4.2.1 Install........................................................................................................................ 4
4.2.2 Uninstall...................................................................................................................8
4.3 Manually Install Through Other USB Port.........................................................................8
4.3.1 Windows 2000..........................................................................................................8
5. Run the Application................................................................................................................9
6. Connect/Disconnect..............................................................................................................11
7. Connection Records..............................................................................................................12
8. Voice Call.................................................................................................................................13
9. Call History .............................................................................................................................16
10. Short Message........................................................................................................................17
11. Phone Book............................................................................................................................19
12. Setting....................................................................................................................................20
13. Help .......................................................................................................................................23
14. Connect to the Website..........................................................................................................23
15. Trouble-shooting....................................................................................................................23
16. FCC Regulations....................................................................................................................27
ZTE Corporation http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
1. Introduction
Thank you for choosing AC8716 CDMA2000 1X EV-DO Wireless Data Terminal (hereinafter referred to as Data Terminal) of ZTE Corporation.
Data Terminal equips with a standard USB interface and supports both CDMA2000 1X
The EV-DO and CDMA2000 1X network. In the area where there is signal, it allows you to go surfing on the Internet, send
The Data Terminal adopts two designing options: R-UIM and Built-in UIM, which make your operation more flexible.
The pictures in this guide are only used to demonstrate your Data Terminal’s functions, so they are maybe different from what you see on your Data Terminal. Please refer to your Data Terminal if they are differences.
& receive short messages, and make & receive phone calls.
2. Precautions
z Use the original accessories or those authenticated by the manufacturer. Using any
unauthenticated accessories may affect the data terminal’s performance, violate the warranty provisions or relevant national regulations about telecom terminals, or even cause body injury.
z Do not disassemble, modify, frequently pull/plug the antenna, stretch, rotate or bend the
antenna with great force.
z Before pulling out the data terminal, please use Windows safely removing the hardware and
make sure to exit the application. Do not directly pull out the terminal to avoid the damage of data terminal or the influence on the normal operation of operating system.
z Do not forcefully plug/pull the data terminal to avoid the damage of connector. z Do not use your data terminal near weak signal or high-precision electronic devices. Radio
wave interference may cause misoperation of electronic devices or other problems.
z Turn off your data terminal on airplane where it’s forbidden to use it. The data terminal may
affect the normal operation of electronic devices, therefore please follow the relevant regulations when using your mobile phone on airplane.
z Turn off your data terminal in hospital where it’s forbidden to use it. The data terminal may
affect the normal operation of medical apparatus, therefore please follow the relevant regulations when using your mobile phone in hospital.
z Please do not use the data terminal near flammable or explosive materials, otherwise it might
cause failure or fire.
z Keep your data terminal away from water. This may cause overheating or failure if water or
any other kind of liquid enters your mobile phone. Please do not use your data terminal near high temperature, damp or dusty place.
z Keep your data terminal away from children to avoid shock, plunge or impact. It may cause
body injury when the data terminal is used as a toy.
ZTE Corporation 1 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
3. Appearance
3.1 Introduction
LED status descriptions:
Inserting
LED
Yellow ON OFF Slow Flash OFF Quick Flash OFF Flash
Green ON Slow Flash OFF
the data terminal
Network Registered
EV-DO 1X EV-DO 1X EV-DO 1X
Service available or Searching for the network
Quick Flash
OFF Flash OFF
Upon an incoming call(as the terminal supports voice call)
3.2 Insert R-UIM Card
Note: If your data terminal doesn’t need R-UIM card, please skip this section.
1. Pull out the tap
2. Take out the R-UIM card cover in the direction indicated by the arrow
ZTE Corporation 2 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
3. Insert R-UIM card as below figure
4. Push back R-UIM card cover in the direction indicated by the arrow.
3.3 Operation Guide of Data Cable
Generally, the Data Terminal could be directly connected with USB port. You could also connect the Data Terminal with PC by using the accompanying data cable, as shown in the following figure. Connect Interface with Data Terminal, and interface with PC's USB port. If the power supply from USB port is insufficient, connect both interface and with USB port together.
ZTE Corporation 3 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
4. Install and Uninstall
4.1 System Requirements
The Data Terminal supports the following operating system:
¾ Windows 2000 ¾ Windows XP ¾ Windows Vista
PC minimum configurations:
CPU Pentium-II/233MHz USB interface Optical Drive CD-ROM (for installation only) Memory 64 MB Disk Space 50 MB (used for installation of application)
2.0 (USB1.0 and 1.1 compatible)
4.2 Installation Guide
Take Windows XP for example. Under other operating systems, please refer to the installation under Windows XP. Do not insert the Data Terminal before installation.
4.2.1 Install
1. Find “setup.exe” firstly in the Data Terminal CD-ROM, double-click it to display the
Welcome picture, and then click “Next”;
2. Select the location where you want the program to be installed, and then click “Next”;
ZTE Corporation 4 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
3. Select Start Menu folder, and then click “Next”;
4. When you see the window below, please click “Install”;
Please wait for installation;
5.
ZTE Corporation 5 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
6. Please inse rt the Data Terminal into USB interface if the system prompts you to insert the
hardware; (If it has been inserted, please unplug it and insert again.)
7.
The system shall find the new hardware and install the driver automatically. Just wait a minute;
ZTE Corporation 6 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
8. The driver is installed successfully. Pleas click “OK”;
9. Click “Finish” to close the last screen of the wizard. Now you can start the application for
data terminal.
ZTE Corporation 7 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
4.2.2 Uninstall
1. Select Start -> All Programs -> ZTE Wireless Terminal -> Uninstall ZTE Wireless
Terminal. Click “Uninstall ZTE Wireless Terminal”, and you will be asked if you want to
remove the program. Click “Yes”.
2. Please wait.
3. Click “OK” when un-installation is completed.
4.3 Manually Install Through Other USB Port
If the data terminal doesn't work through other USB ports after the driver is installed successfully through a USB port, you could manually install the driver in the following method. Please make sure to quit other applications during the installation.
4.3.1 Windows 2000
Insert the data terminal to another port, and the system will find new hardware and automatically install the driver. When the following prompt appears, click “Yes”. Now you can start the
ZTE Corporation 8 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
application for data terminal.
5. Run the Application
After the application is installed successfully, the application icon will appear on your desktop. Double-click this icon or select from Start -> Programs ->ZTE Wireless Terminal ->
ZTE Wireless Terminal. Run the application to display the following user interface.
Press
to display other icons. The icons on the interface are used to access the function,
which indicate as below:
Connect / Disconnect
Voice Call
ZTE Corporation 9 http://www.zte.com.cn
Call History
Open URL
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
Short Message
Phone Book
Connection Record
Help
Status Bar:
EV-DO indication 1X indication 1X/DO indication Signal strength indication. The
more bars there are, the stronger signals are.
CDMA network unavailable Connection indication Sleep indication
Setting
Call indication Missed call indication Unread message indication Inbox full indication
No R-UIM card inserted indication R-UIM card inserted indication Roaming indication
Note:
Some features like Voice Call, Call History, Short Message, and Phone Book may not be supported by your Data Terminal; the corresponding icons will not appear in the main window.
ZTE Corporation 10 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
6. Connect/Disconnect
Connect
Click icon to set the rele vant parameters. For details, please refer to Chapter 12
“Setting” for details.
Click
icon at the left-up corner of the interface.
After connecting to Internet, the current network information will appear on the
interface. Double-click any place in the display area to view the connection drawing.
Please connect the Data Terminal and PC with USB extension cable under weak signal
to obtain the optimal performance. If necessary, adjust the Data Terminal's position and the antenna's direction.
Disconnect
After connecting to Internet, click the rotating icon
at the left-up corner of the interface.
ZTE Corporation 11 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
7. Connection Records
Click
icon to view connection records. Connection records save the previous relevant
information including Start at, Duration and Transmit bytes, which will help you know the status easily.
By switching among “List”, “Monthly” and “Statistic”, you could inquire the records every time, by month or by time.
Note:
The relevant information contained in connection records are just for user’s reference rather than the charging basis.
Delete Connection Records
Click
button to delete the records you have selected on the interface.
Clear Connection Records
Click
button to delete all the records.
Note: If your data terminal doesn’t support Voice Call, Call History, Short Message, and Phone Book features, please skip 8-11 sections.
ZTE Corporation 12 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
8. Voice Call
Click
to enter voice call interface.
Make a call
Click the digits in the right side of the interface, or input the digits directly from
keyboard. Press press
Click
button or press “Esc” to clear all the inputs.
button in the right side of the interface or press “Enter” to make a call.
button or press “Backspace” to delete the previous input digit;
Receive a call
When there is an incoming call, your computer will alert and the incoming caller ID will
appear on the interface.
Click
Press
button in the right side of the interface or press “Enter” to receive the call.
button or press “Esc” to reject the call.
Redial the latest outgoing call
Click
button in the right side of the interface.
Call Waiting
During a call, you could select to answer the second incoming call, and then you could switch
ZTE Corporation 13 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
between the two incoming calls. Please firstly apply for this service from your local telecom operator.
During a call, if there is a new incoming call, a pop-up window will prompt you that you
have the second incoming call.
If you select to answer, please click “Accept waiting call” button. The previous call
won’t be ended, but temporarily paused.
You could switch between two incoming calls by clicking “Switch call”.
ZTE Corporation 14 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
Three-way Call
This function allows for the call among three parties. Please firstly apply for this service from your local telecom operator.
Note: You need set “Show 3 way call button during calling”. Please perform the setting according to
chapter 12.
You could click “Dial second call” button during a call, input the third-party number in
the pop-up window, and then press “OK” button to call the third party. In this case, the original call won’t be ended, but temporarily paused.
If the third party answers the call, click “Start conference” to enter the conference call.
ZTE Corporation 15 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
During three-way conference call, click “Hangup second call” button to end the
conference call, and return to the original call.
9. Call History
Click including missed calls; incoming calls, outgoing calls, and talk duration. You could select the type
you want to view.
icon to view the call history. The outgoing/incoming calls are saved in call history,
Missed/Accepted/Called Calls
Click
Click
ZTE Corporation 16 http://www.zte.com.cn
button to delete your selected record.
button to delete all records in Missed/Incoming/Outgoing catalog.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
Click button to dial the number.
Click
Click
Statistic
Click
10. Short Message
button to send a short message to this number.
button to save this number to the phone book.
button to clear the talk duration.
Click
icon to enter Short message interface.
Send a Message
Input the text to sendor click Input the recipient’s number or click
button to select the preset message to send.
button to select the recipient from phone
book.
Add more recipients if you like. Select priority. Click Click
ZTE Corporation 17 http://www.zte.com.cn
button to send a message.
button to save the text into outbox.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
The received messages will be saved in the Data Terminal In-box. After the Data Terminal In-box is full, the system will automatically move the messages in the Data Terminal In-box to the PC In-box, and clean out the Data Terminal In-box.
You could copy the messages from the Data Terminal In-box to PC In-box by selecting Copy or Copy All; you could also copy the messages from PC In-box to the Data Terminal In-box by selecting Copy.
The sent messages and unsent but saved messages will be all saved in the Out-box. Take Data Terminal In-box as an example:
Reply
Click
to reply to the sender.
Forward
Click
to forward this message to other recipients.
Dial Sender’s Number
Click
to dial the sender’s phone number.
Save Sender’s Number
Click
to save the sender’s number into phone book.
Delete
Click
to delete your selected records.
Clear
Click
to delete all the records in the inbox.
Copy
Click
to copy your selected record into PC.
Copy All
Click
ZTE Corporation 18 http://www.zte.com.cn
to copy all the records from the data terminal to PC.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
11. Phone Book
Click
to view the Phone book. You could select to save the contacts either in the
PC(computer)、Normal(data terminal)、R-UIM Card(If your data terminal needs R-UIM card) or in the Emergent. Click the pull-down menu to select the storage location.
Add
Click
then input the contents and select “OK” to add a new contact.
Modify
Click then modify the contents and select “OK” to modify the contact
information.
Dial from the phone book
Click
to dial your selected phone number.
Send messages from the phone book
Click
to compose the text. You could send the message to multiple
recipients.
Search for contacts
Click
to search for the contacts by name or number.
Delete
Click to delete your selected contact.
ZTE Corporation 19 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
Delete All
Click to delete all the contacts.
Copy
Click to copy your selected contacts to other storage location.
Copy All
Click to copy all contacts to other storage location.
12. Setting
Click
to enter the setting interface.
Network Connection Setting
Set up the relevant parameters, work mode on the “Network” interface. After the setting, click “Apply” button to save the settings on the current interface. Click “Default” button and then “Apply” button to restore the settings on the current
interface to factory default.
Note:
The default network setup parameters are as below. Different regions may have different network setup parameters, so please consult your local telecom operator.
Phone: #777 User: card Password: card
ZTE Corporation 20 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
Other Setting:
Click “Options” to switch the interface, and you could set URL and select the skin,
language, etc. If you want to use conference call, please select “Show 3 way call button during calling”;
After the setting, click “Apply” button to save the settings on the current interface.
Click “Change Password” button to set lock device. The password is required when you
start the application. The setting has nothi ng to do wit h " D efault" butt on.
If your data terminal needs R-UIM card, please click the button “Enable Pin”. PIN code
is needed when the application is started. The setting has no thing to do with "Default" button.
Click “Default” button and then “Apply” button to restore the settings on the current
interface to factory default.
ZTE Corporation 21 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
Select ring tone
After clicking “Ring”, you could set different ring tones for Call coming, New message,
Call connected, Call disconnected and Waiting call.
After the setting, click “Apply” button to save the settings on the current interface.
Click “Default” button and then “Apply” button to restore the settings on the current
interface to factory default.
Supplementary Services
After clicking “Service”, you could set “Unconditional forward ing”, “Bu sy Forwardin g”,
“No answer forwarding”, “Call waiting”, etc. Double-click the select ed op tion to mo d ify the service number and forwarding number.
After the setting, click
button to send the corresponding request to the
network system.
After the setting, click “Apply” button to save the settings on the current interface.
Click “Default” button and then “Apply” button to restore the settings on the current
interface to factory default.
ZTE Corporation 22 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
13. Help
Click
Click “Help” button to view the relevant help file; click “Online service” to enter our
You could view the software version information under “About”.
button to view the help file.
company’s website.
14. Connect to the Website
Click button to directly connect the website you set. For details on the website setting, please refer to Chapter 12 “Setting”.
15. Trouble-shooting
After the installation, go to device manager and find “ZTE USB Modem FFFF” under “Modem” and “ZTE Service Port FFFF”, “ZTE Voice Port FFFF” under “Port”. If they are not found, please remove the software and reinstall.
ZTE Corporation 23 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
Common Failures Table:
Failures Causes Solutions
Error occurs during the program installation.
Open port failed.
No R-UIM card.
No signal indicated.
ZTE Corporation 24 http://www.zte.com.cn
The setup file may be damaged. Directly run the software before the Data Terminal is plugged in.
The port is occupied by other applications, such as “Hyper terminal”, or the software is already run.
R-UIM card is not inserted. R-UIM card is not inserted properly. Sometimes the front side and back side are confused.
R-UIM card is damaged. Validate by using a CDMA terminal.
Antenna is not Insert the antenna into the Data Terminal.
Please download the program on our website
WWW.ZTEMT.COM
Close the software, plug in the Data Terminal and run it again.
Close relevant software and run the software again.
Insert R-UIM card.
Please refer to User Guide. Properly insert R-UIM card.
Replace R-UIM card.
and reinstall it.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
connected to the Access Box.
Out of the network service area.
Make sure it is in the CDMA network service area.
The antenna or RF component is
Replace relevant damaged parts. damaged. Wrong setting of parameters. (Phone, User,
Correct the parameter settings. Consult your service provider
for details. Password.)
Dialing failed.
Not enough money. Consult your service provider for details. Network
congestion or
Try again later. failure. The Data Terminal is being connected. (It usually occurs when the Internet
Internet connection failure.
connection is immediately made
Reconnect.
after the call is dialed.)
Poor network signal.
View signal strength indication and check if the antenna is
properly inserted. The program has
already been installed in current
Firstly remove the original program and insert the terminal
again. system. Autorun function in CD-ROM is
The installation program can’t auto set up. (If the Data Terminal supports auto setup function.)
disabled because of installation of anti-virus software in the system, or Windows Vista
Open “My Computer” to enter CD-ROM disk ordinal, and
double-click Setup.exe to install manually. system itself disabled Autorun function in CD-ROM in default.
No CD-ROM disk ordinal in “My Computer”.
ZTE Corporation 25 http://www.zte.com.cn
CD-ROM will automatically disappear once the
This is normal. If you want to display CD-ROM disk ordinal,
you could firstly remove the program and then insert the
terminal again.
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
program is installed successfully.
The program is not yet installed, and no other previous version was installed in the system.
The driver might be unable to work and the application is unable to run normally if the terminal is pulled out and plugged in again when the application is being used under Win2000 operating system (SP4).In this case, the device in device manager will be marked with yellow exclamation mark, and the system must be restarted to run normally.
The operating system needs installing Update Roll 1 patch for Win2K SP4.
Please restart your computer. Please contact your local
operator or product technical support center if CD-ROM disk
ordinal doesn't appear after your computer is restarted.
Please download the patch from the following web site and
install it.
http://www.microsoft.com/downloads/details.aspx?familyid=
B54730CF-8850-4531-B52B-BF28B324C662&displaylang=
en
ZTE Corporation 26 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
16. FCC Regulations
z This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
z This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferen ce will not occu r in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
4RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves. This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.
The highest SAR value for the device as reported to the FCC when tested for body, as described in this user guide, is 0.784 W/kg for CDMA 850 band.
While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement.
*
Tests for SAR are
ZTE Corporation 27 http://www.zte.com.cn
CDMA2000 1X EV-DO Wireless Data Terminal User Guide
The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of
http://www.fcc.gov/oet/fccid
after searching on FCC ID: Q78-AC8716.
For body operation, this device has been tested and meets the FCC RF exposure guidelines for use the positions the device a minimum of 0.5 cm from the body. Use of other enhancements may
not ensure compliance with FCC RF exposure guidelines.
ZTE Corporation 28 http://www.zte.com.cn
Loading...