Page 1
Operation Manual
Copying or reprinting this manual in part or in whole without permission is prohibited.
© 2014 ZOOM CORPORATION
Page 2
Contents
Introduction ………………………………2
Introduction
Usage and Safety Precautions ……… 3
Part Names ………………………………4
Installing the Driver …………………… 6
Connecting with a Computer ………… 7
Recording ………………………………… 8
Playback ……………………………… 11
Connecting MIDI Devices …………… 13
Restoring Factory Default Settings 13
Troubleshooting ……………………… 14
Specifications ………………………… 15
Introduction
2-in/2-out Thunderbolt™ audio converter
The audio converter uses Thunderbolt™, the latest generation of high-speed interface
technology. With this, we have realized a system with low latency that was not possible using USB 2.0.
Since it also supports recording and playback at up to 24-bit/192kHz, it can also be used for the playback
of high-resolution sound sources delivered with superior audio quality over the Internet.
Attention to audio performance
The entire system reproduces the original audio faithfully. An asynchronous transfer system
that is not impacted by computer jitter is used along with the latest AD/DA converter, which
supports 192kHz.
Built-in high-performance mic preamps
The high-performance mic preamps are based on those developed for our H Series. Each
input also supports Hi-Z connections . The gain can be raised by up to 60 dB , and +48V
phantom power can be supplied.
dedicated mixer application
Use this application to make internal mixer and monitoring effect settings. For details about
2
, see the ZOOM website (http://www.zoom.co.jp/downloads/).
Page 3
Usage and Safety Precautions
Warning
Caution
Usage and Safety Precautions
In this operation manual, symbols are used to highlight warnings
and cautions that you must read to pre vent accidents. The
meanings of these symbols are as follows.
Something that could cause serious injury or death
Something that could cause injury or damage to the
equipment
Other symbols used
An action that is mandatory
An action that is prohibited
Warnings
SAFETY PRECAUTIONS
Alterations
Do not open the case or modify the product.
Precautions
Product handling
Do not drop, bump or apply excessive force to the unit.
Be careful not to allow foreign objects or liquids enter the unit.
Operating environment
Do not use in extremely high or low temperatures.
Do not use near heaters, stoves and other heat sources.
Do not use in very high humidity or where it could be splashed by water.
Do not use in places with frequent vibrations.
Do not use in places with much dust or sand.
Connection cables and input/output jacks
Always turn the powe r OFF for all equipment before connecting any
cables.
Always di sconnect all c onnection cables and the AC adapter before
moving the unit.
Volume
Do not use at a loud volume for a long time.
Interference with other electrical equipment
Usage Precautions
In consideration of safety, the has been designed to minimize its
emission of electromagnetic waves and to suppress interference from external
electromagnetic waves. However, equipment that is very susceptible to interference
or that emits powerful electromagnetic waves could result in interference if placed
nearby. If this occurs, place the and the other device farther apart. With
any type of electronic device that uses digital control, including the ,
electromagnetic interference could cause malfunction, corrupt or destroy data and
result in other unexpected trouble. Always use caution.
Cleaning
Use a soft cloth to clean the exterior of the unit if it becomes dirty. If necessary, use
a damp cloth that has been wrung out well. Never use abrasive cleansers, wax or
solvents such as alcohol, benzene or paint thinner.
Temperature considerations
Continuous use of this interface for long periods of time, for example, might cause it
to become warm. This is normal as long as it does not become too hot to touch.
Breakdown and malfunction
If the should malfunction or operate abnormally, disconnect it
immediately. Then, contact the retailer where you purchased it or Zoom support and
provide the following information: product model, serial number and details of the
symptoms of malfunction or abnormal operation, as well as your name, address and
telephone number.
Copyrights
• Macintosh and Mac OS are trademarks or registered trademarks of Apple Inc.
• Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation in the U.S.
and/or other countries.
•
MIDI is a registered trademark of Association of Musical Electronics Industry (AMEI).
• All other product names, trademarks and company names in this document are
the property of their respective owners.
Note: All trademarks and registered trademarks in this document are for
identification purposes only and are not intended to infringe on the copyrights of
their respective owners.
Recording for any purpose other than personal use from copyrighted sources,
including CDs, records, tapes, live performances, video works and broadcasts,
without permission of the copyright holder is prohibited by law.
Zoom Corporation will not assume any responsibility related to infringements of
copyrights.
3
Page 4
Part Names
XLR TRS
1 : GND
2 : HOT
3 : COLD
TIP : HOT
RING : COLD
SLEEVE : GND
12
3
Part Names
Top Panel
Level indicators GAIN knobs PHONES knob
Power indicator
INPUT 2 jack
OUTPUT knob Hi-Z switches
INPUT 1 jack
4
PHONES jackPHANTOM switch
Page 5
Rear Panel
Thunderbolt port DIRECT MONITOR switch
Part Names
MIDI OUT jack
MIDI IN jack
OUTPUT jacks
5
Page 6
Installing the Driver
Installing the Driver
Do not connect the until installation completes.
1.
Download the ZOOM TAC-2 Driver from http://www.zoom.co.jp/
downloads/ to your computer.
NOTE
• You can download the latest ZOOM TAC-2 Driver from the above website.
• The supported operating systems are as follows.
Mac OS X 10.8.5 (or later)
2. Click the ZOOM TAC-2 Driver.pkg icon to launch the installer.
Follow the instructions that appear on screen to install the ZOOM TAC-2 Driver.
3.
Connect the and the computer using a Thunderbolt cable.
4. Open the Sound pane of the System Preferences and set
both the Input and Output to
ZOOM TAC-2R.
6
Page 7
Connecting with a Computer
1.
Minimize both volume controls on the .
2.
Connect the and the computer using a Thunderbolt
cable.
The power indicator will light when connected correctly.
<Rear>
NOTE
• The unit will not turn on if the driver is not installed.
Follow the instruction on page 6 to install the ZOOM TAC-2 Driver.
Connecting with a Computer
7
Page 8
Connecting Instruments
Bass guitar
(TRS cables)
(mono phone cable)
Keyboard
Guitar
Connect instruments to INPUTS 1/2 using TRS/mono phone cables.
Recording
<Front>
Connecting Instruments
Using the Hi-Z Function
• When connecting a passive guitar or bass guitar to
an INPUT, press its so that it lights.
• When connecting a keyboard or other instrument to
an INPUT, press its so that it becomes unlit.
8
Page 9
Connecting Mics
Dynamic mic
Condenser mic
(XLR cable)
(XLR cable)
Using XLR cables, connect mics to INPUTS 1/2.
Using Phantom Power
• When connecting a condenser mic, press so that
it lights. Phantom power is supplied when this switch
is lit.
• When o n, pha nt om p owe r is sup pl ie d to bot h
INPUTS 1/2.
Recording
<Front>
Connecting Mics
9
Page 10
Adjusting Input Gain
You can adjust the gain of each INPUT.
Recording
1. Check the status of the input
signal.
Lit green: Input signal present.
Lit red: Input signal is clipping.
Adjusting Input Gain
2. Adjust the input gain.
Turn the .
HINT
• Set it so that the level indicator does not light red.
10
Page 11
Connecting Headphones and Speakers
Speakers
Headphones
Connect headphones to the PHONES jack and speakers to the OUTPUT
jacks. Then, adjust the volume.
1.
Connect headphones or speakers.
<Front> <Rear>
2.
Adjust the headphones/speakers volume.
Headphones volume:
Speakers volume:
Turn .
Turn .
Playback
Connecting Headphones and Speakers
11
Page 12
Using Direct Monitoring
Sound inputs into the can be directly output without passing
Playback
through the computer. This enables monitoring without latency.
1. Set the .
Using Direct Monitoring
Direct monitoring setting
MONO Output from the PHONES jack and both L/R OUTPUT jacks.
STEREO Output from the PHONES
OFF This disables direct monitoring.
12
<Rear>
INPUT 1 jack INPUT 2 jack
jack and the L OUTPUT jack.
Output from the PHONES
jack and the R OUTPUT jack.
Page 13
Connecting MIDI Devices
Sound module
MIDI OUT jack MIDI OUT jack MIDI IN jack MIDI IN jack
MIDI keyboard,
MIDI controller
Use MIDI cables to connect MIDI devices to the MIDI IN and MIDI OUT jacks.
<Rear>
NOTE
• When making settings in a DAW or other software, select "ZOOM TAC-2R MIDI I/O Port". Do
not use "ZOOM TAC-2R Reserved Port".Doing so could cause the or
to stop functioning properly.
Restoring Factory Default Settings
Follow these instructions to initialize settings, restoring them to their factory defaults.
1. Connect the to a computer while pressing . (→P.7)
2.
Initialize the settings.
Execute:
Press .
Execute
Connecting MIDI Devices / Restoring Factory Default Settings
Cancel:
Press .
Cancel
13
Page 14
Troubleshooting
Troubleshooting
Cannot select or use the device
Confir m th at th e • i s c onne cted to th e
computer correctly.
Quit all the soft ware that is using the •
and disconn ect and reconnec t th e T hunderb olt
cable c onnected t o the
Reinsta ll the drive r.•
Playback sound cannot be heard or is quiet
Ch ec k the spe ake r c on ne ct io ns an d volu me •
setting s on the spe akers.
Ad jus t the OUT PU T an d PHO NE S vo lu me •
controls.
Confirm that the Output of the Sound pane of the •
System Preferences is set to ZOOM TAC-2R.
Recorded audio is too loud, too quiet or silent
Adjust th e input gai n of the • .
When using a conde nser mic, turn phanto m •
power on.
Confirm th at the Input of the Sou nd pane of the •
System Preferences is set to ZOOM TAC-2R.
The sound of the device connected to the
input jack is distorted
Confir m that the level indica tors a re not lighting •
,
.
red. If they a re lightin g, lower the i nput level s.
Sound skips during playback or recording
If you can ad jus t the aud io buff er size of t he •
softw are th at you are using, increase the buffer
size.
Cannot play or record
Conf irm that ZOOM TAC-2R is sele cted in the •
Sound pane of the System Preferences.
Confir m that •
in the soft ware that you are using.
Confirm tha t •
computer correctly.
Quit all the soft ware that is using the •
and disconn ect and reconnec t th e T hunderb olt
cable c onnected t o the
is set for inpu t and outp ut
is con nec ted to the
,
.
14
Page 15
Specifications
Inputs INPUT 1/2 Connector XLR/TRS combo jacks (XLR: 2 hot, TRS: TIP hot)
Outputs OUTPUT
L/R
PHONES Connector Standard stereo phone jack
Frequency characteristics At 44.1 kHz −1.0 dB: 20 Hz – 20 kHz
Input conversion noise
Dynamic range AD: 118 dB typical (IHF-A)
Number of audio recording and
playback channels
Sampling frequencies 192 kHz, 176.4 kHz, 96 kHz, 88.2 kHz, 48 kHz, 44.1 kHz
Bit depth 24-bit
Interface Thunderbolt™
MIDI IN/OUT 5 pin DIN jack
Power Source Thunderbolt™
Power consumption 10 W maximum
Dimensions 113.9 mm (D) × 176.0 mm (W) × 46.2 mm (H)
Weight (main unit only) 714 g
• 0 dBu = 0.775 Vrms
Input gain 0–60 dB (in 1dB steps)
Input impedance 5 kΩ
Maximum input level +12 dBu (at 0 dBFS)
Phantom power +48V
Connector TRS jack (balanced)
Maximum output level +14 dBu (at 0 dBFS)
Output impedance 10 0 Ω
Maximum output level +8 dBu (at 0 dBFS)
Output impedance 33 Ω
1 MΩ (when Hi-Z ON)
20 mW × 2 (into 32Ω load)
At 96 kHz −1.0 dB: 20 Hz – 40 kHz
At 192 kHz −1.0 dB: 20 Hz – 60 kHz
Measured EIN: −125 dBu (IHF-A) (with 60dB, 150Ω input)
DA: 120 dB typical (IHF-A)
Recording: 2 channels
Playback: 2 channels
Specifications
15
Page 16
FCC regulation warning (for U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These lim its are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, a nd can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•
• Consult the dealer or an experienced radio/TV technician for help.
For EU Countries
Declaration of Conformity:
This product complies with the requirements of EMC Directive 2004/108/
EC and RoHS Directive 2011/65/EU
Disposal of Old Electrical & Electronic Equipment
(Applicable in European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. The recycling of materials will help to conserve natural
resources. For more detailed information about recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you purchased the product.
ZOOM CORPORATION
4-4-3 Kanda-Surugadai, Chiyoda-ku, Tokyo 101-0062 Japan
http://www.zoom.co.jp
Z2I-2193-02
Loading...