ZKaccess C3-200 Installation Manual

www.zkteco.com

Safety Precautions

Product Contents

Product

PIN Diagram

LED

indicators

Product Dimension

Installation of Panel with Casing

Wire Legend

Power

Wiring Diagram

WEIGAND Connection

Exit button Connection

Lock connection

Door

Sensor Connection

Aux. Input Connection

Aux. Output Connection

Ethernet Connection

RS485 Connection

DIP switch settings

Electrical

Specifications

Troubleshooting

Specification

s

1

02 04

06 06

07

08 09 10

11

12 12 14

14 15

16

17 18

19 20

1

2

Safety Precautions

Do not install the device in a

place subject to direct sun light, humidity, dust or soot.

Do not place a magnet near the product. Magnetic objects such as magnet, CRT, TV, monitor or speaker may damage the device.

Do not place the device next to heating equipment

Be careful not to let liquid like water, drinks or chemicals leak inside the device.

Clean the device often to remove

dust on it

01 02 03

04 05 06

Do not let children touch the

device without supervision.

The list below is to keep user’s safety and prevent any loss. Please read carefully before installation.

3

Safety Precautions

The list below is to keep user’s safety and prevent any loss. Please read carefully before installation.

Do not drop the device.

Do not use the device for any other purpose than specified.

Do not disassemble, repair or alter the device.

07

08

In cleaning, do not splash water on the device but wipe it out with smooth cloth or towel.

09

Contact your nearest dealer in case of a problem.

Do not damage the device

10

11 12

4

Product Contents

Basic Contents

C3-200

Wall mounting screws – 2 pcs. Wall Plugs– 2 pcs. Surge Suppressing Diode– 4 pcs.

screw driver – 2 pcs.

Software CD C3 installation guide

5

Product Contents

Optional accessories

Weigand Card Reader Prox Card

Card enroller

Door Sensor

K1-1 Exit Button

Alarm C3 Metal Case

RS485 convertor

6

Product PIN Diagram

#2 Door Card

Reader 2

#2 Door Card

Reader 1

#1 Door Card

Reader1

#1 Door Exit

Button

Aux Input 4

Aux Input 1

SD Card Slot

LINK LED

ACT LED

Ethernet Port

DIP Switch

PC RS485 Port

Aux Output 1

Aux Output 2

Lock Power

C3 Power

LED indicators

LINK (Green)

LED solid green indicates TCP/IP communication is normal

ACT (Yellow)

Flashing LED indicates data communication is in progress

PC RS485 (Yellow & Green)

Flashing LED is sending or data in communication progress

POWER (Red)

Flashing LED indicates the panel is powered on.

RUN (Green)

Flashing LED indicates that panel is in normal working state

CARD

(Yellow)

Flashing LED indicates that

the card is read by the panel.

Reserved

485 LED

Status LED

#1 Lock Sensor

#1 Door Lock

#2 Lock Sensor

#1 Door Lock

#1 Door Card

Reader2

#2 Door Exit

Button

7

C3-200

Product Dimension

Dimension(L*W):203.2× 106 (mm)

6.30 ×4.17（inches）

160mm

(6.30in.)

106mm

(4.17in.)

C3-Casing

400mm

(15.7in.)

330mm

(13.0in.)

330mm

(13.0in.)

90.5mm

(3.56in.)

Dimensions(L*W*H): 400 *90.5*330（mm）

15.7× 13.0× 3.56(inches)

8

Installation of Panel & Case

Metal Case

Heat dissipation Hole

Cable Conduit

Box Lock Hole

Power Supply

Backup Battery

C3 Panel

Thread Hole

Wires need to be passed through this conduit

Mounting the case on the wall

Wire Legend

9

Detector Infrared sensors #1Exit Switch #1Card Reader

#2 K1-1 Exit Switch

#2 Card Reader

12V

Power Supply

Normal Close Lock

Normal Open Lock

Alarm

RS485 Convertor

LAN Cable

Floodlight

12V DC

Power

DC

Power wiring diagram

10

AC

Switching power supply

C3-200

AC

Switching power supply

C3-200

Backup Battery

+

-

Without

Backup Battery

With

Backup Battery

110-220V

Weigand Connection

11

Weigand Card Reader

Exit Button Connection

Beeper

Green LED

Weigand D1

Weigand D0

GND

DC+(6-14V)

BUT

GND

DV12V（+）

DV12V（-）

NO

COM

NC

separate power supply

Notice：

ZK ABK Exit Button

K1-1 Exit Switch

12

Lock Connection

Built-in Power Supply

Sensor

GND

12V DC

GND

Sensor

GND

12V DC

GND

FR107

For Normally Open Lock

For Normally Close Lock

Lock Connection

13

Switching Wet Contact to Dry Contact

Important Notes:

C3-200 is set to supply lock power by default from external power supply , If you want to use built-in

power supply , you must do the following:

1. Select the wanted lock relay and find its jumpers

2. Take off the jumpers and change to

3. Connect the lock as shown in the diagram below

Steps:

C3-200

Select one Relay

FR107

GND

12V DC

SEN SEN GND 12V DC

4 Lock Relays

Default setting

1

5

Take off jumpers

Jumpers Plug Jumpers

Changed setting

5

1

Connecting a lock with external power supply

14

Aux. I/O connection

Aux. Input Connection

Aux. output Connection

COM

NO NC

GND

12V DC

COM

NO NC

GND

12V DC

15

Ethernet Connection

Direct connection

Important Notes:

1. Both 10Base-T and 100Base-T are supported

2. This cable distance must be less than 100 meters or 330 ft.

3. For cables length of more than 100m. use HUB to amplify the signal

TCP/IP

CR10 Card Issuer

The CR10 is connected to the server using USB connection.

To connect C3-200 with a PC directly, connect both devices with a straight network cable. As the C3-200 supports auto MDI/MDIX , it

is not necessary to use a crossover type cable.

CR10 Card Issuer

C3-200

16

RS485 Connection

Important Notes

#1 C3-200

#63 C3-200

RS485-

RS485+ GND

1. RS485 communication wires should be shielded or twisted pair calble. RS485 communication wires should be connected in a bus cascade instead of in a star form, to achieve a better shielding effect by reducing signal

reflection during communications.

2. A single 485 bus can be connected with 63 access control panels at the most, but preferably less than 32 panels should be connected.

3. To eliminate signal attenuation in communication cables and suppress interference, if the bus is longer than 200 meters, set the number 8 DIP switch to the ON position. This is equivalent to a parallel connection of one

120ohm resistance between the 485+ and 485- lines.

Distance

More than 200 meters

#1 C3-200

#* C3-200

Do's and Dont's for RS 485 connection

17

DIP Switch Setting

Introduction

RS485 Address

1. Number 1-6 are reserved to set the device number for RS485 communication. The code is binary, and the numbering starts from left to

right. When the switch is set to ON position, it indicates 1 (on); when the

switch is set downwards, it indicates 0 (off). For example, to set a device number 39=1+2+4+32, which corresponds to the binary code 111001, put number 1, 2, 3, and 6 to ON position, as illustrated below.

2. For more details, please check the table at the end of this document

Restore factory setting

1. If you forget the C3 IP address or the device does not work normally, you can use the number 7 terminal to restore C3-200 to factory default settings. The parameters which gets reset are device IP address, communication password ,gateway ,subnet mask.

2. The switch is OFF by default. When it is moved upwards and downwards for three times within 10 seconds and finally returned to OFF position, the factory settings will be restored after the access control panel is restarted.

1 times

2 times

3 times

OFF

Terminal Resistance

1. Number 8 is for setting the RS485 termination resistance. Putting the switch to ON position is equivalent to parallel connection of a 120ohm termination resistance between 485+ and 485-

2. For more information please read RS485 connection - important notes

120ohm

Electrical Specifications

18

Min. Typ. Max. Notes

Working power supply

Voltage(V) 9.6 12 14.4 Use regulated DC power adaptor only

Current(A) 2

Electronic lock relay output

Switching voltage(V) 36V Use regulated DC power adaptor only

Switching Current(A) 2

Auxiliary relay output

Switching voltage(V) 36V Use regulated DC power adaptor only

Switching Current(A) 1.25

Switch Aux. input

VIH (V) TBD

VIL (V) TBD

Pull-up resistance (Ω) 4.7k The input ports are pulled up with 4.7k resistors

WIEGAND Input

Voltage(V) 10.8 12 13.5

Current(mA) 500

ZK Electronic lock

Voltage(V) 10.8 12 13.2

Current(mA) 500

Troubleshooting

19

1. How to switch four door one way to two door to way.

 Connect four readers from reader 1 to reader 4.  Connect two door locks , one connect LOCK1 ,another connect LOCK3.  Switch on software then reader 1-Indoor, reader 2-Outdoor. 

2. How many WEIGAND formats are supported ?

 The panel is set to read 26 bit by default.  However there are 9 other bit formats which can be selected from the software. In addition you

can also define your custom bit format.

3. How many verification mode can be support.

 Card only  Password only  Card plus password

4. Can we integrate IP Camera and NVR

 Currently ZKACCESS software supports ZKAccess’ IP Cameras and NVR

 You can associate a camera to the door and setup a linkage for the same.

5. Can C3 panel support FR1200 fingerprint reader ?

 No , Only Inbio series can support FR1200 fingerprint reader

Diagram:

Specifications

20

Communication RS485, TCP/IP

Baud Rate for RS485 9600-115200

Power Supply 12V DC, 3A

Card Holders Capacity 30,000

Log Events Capacity 100,000

LED Indicator Indication for communication, power, status and prox card

Environment

32-113 °F (0-45 °C)

Operating Humidity 20% to 80%

Number of doors controlled Four Door (four door one way two door two way)

Number of readers supported 4

Types of readers supported 26-bits WIEGAND, others upon request

Number of Inputs 6 (2 Exit Device, 2 Door Status, 2 AUX)

Number of Outputs 4 (2- Form C relay for lock and 2- Form C relay for Aux output)

Weight 7.8lbs (3.55kg)

Enclosure Stainless Steel

Mounting Wall Mount

Dimensions (Bundle Only) 15.7in. × 3.56in.× 13.0in 400mm(L) X 90.5mm(W) X 330mm(H)

Dimensions ( Board Only) 6.30in. X 4.17in. 160mm(L)X 106mm(W)

CPU 32 bit 400MHz

RAM 32MB

Flash 128MB

Certified

Attached

21

PC 485 Setting table

Place Address

Switch Setting

1 2 3 4 5 6

Address No. 1 2 4 8 16 32

01 ON OFF OFF OFF OFF OFF 02 OFF ON OFF OFF OFF OFF 03 ON ON OFF OFF OFF OFF 04 OFF OFF ON OFF OFF OFF 05 ON OFF ON OFF OFF OFF 06 OFF ON ON OFF OFF OFF 07 ON ON ON OFF OFF OFF 08 OFF OFF OFF ON OFF OFF 09 ON OFF OFF ON OFF OFF 10 OFF ON OFF ON OFF OFF 11 ON ON OFF ON OFF OFF 12 OFF OFF ON ON OFF OFF 13 ON OFF ON ON OFF OFF 14 OFF ON ON ON OFF OFF 15 ON ON ON ON OFF OFF 16 OFF OFF OFF OFF ON OFF 17 ON OFF OFF OFF ON OFF 18 OFF ON OFF OFF ON OFF 19 ON ON OFF OFF ON OFF 20 OFF OFF ON OFF ON OFF 21 ON OFF ON OFF ON OFF 22 OFF ON ON OFF ON OFF 23 ON ON ON OFF ON OFF 24 OFF OFF OFF ON ON OFF 25 ON OFF OFF ON ON OFF 26 OFF ON OFF ON ON OFF 27 ON ON OFF ON ON OFF 28 OFF OFF ON ON ON OFF 29 ON OFF ON ON ON OFF 30 OFF ON ON ON ON OFF 31 ON ON ON ON ON OFF 32 OFF OFF OFF OFF OFF ON

Place Address

Switch Setting

1 2 3 4 5 6

Address No. 1 2 4 8 16 32

33 ON OFF OFF OFF OFF ON 34 OFF ON OFF OFF OFF ON 35 ON ON OFF OFF OFF ON 36 OFF OFF ON OFF OFF ON 37 ON OFF ON OFF OFF ON 38 OFF ON ON OFF OFF ON 39 ON ON ON OFF OFF ON 40 OFF OFF OFF ON OFF ON 41 ON OFF OFF ON OFF ON 42 OFF ON OFF ON OFF ON 43 ON ON OFF ON OFF ON 44 OFF OFF ON ON OFF ON 45 ON OFF ON ON OFF ON 46 OFF ON ON ON OFF ON 47 ON ON ON ON OFF ON 48 OFF OFF OFF OFF ON ON 49 ON OFF OFF OFF ON ON 50 OFF ON OFF OFF ON ON 51 ON ON OFF OFF ON ON 52 OFF OFF ON OFF ON ON 53 ON OFF ON OFF ON ON 54 OFF ON ON OFF ON ON 55 ON ON ON OFF ON ON 56 OFF OFF OFF ON ON ON 57 ON OFF OFF ON ON ON 58 OFF ON OFF ON ON ON 59 ON ON OFF ON ON ON 60 OFF OFF ON ON ON ON 61 ON OFF ON ON ON ON 62 OFF ON ON ON ON ON 63 ON ON ON ON ON ON

ZK USA office:

201 Circle Drive North, Suite 116 Piscataway, NJ 08854, USA Tel: +1 732-412-6007 Fax +1 732-412-6008 sales@zkaccess.com zkaccess.com

ZKTeco May, at any time and without notice , Make changes or improvements to the product and services offered and/or cease producing or commercializing them.

Functions and specifications of the product are subject to change without notice due to quality enhancement or function update. For any inquiry for the product, please contact ZKTeco Inc .