Zigmund shtain EN 116.622 B User Manual [ru]

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

ЭЛЕКТРИЧЕСКИЕ ВСТРАИВАЕМЫЕ ПЕЧИ

ИНСТРУКЦИИ ПО УСТАНОВКЕ, ЭКСПЛУАТАЦИИ И ОБСЛУЖИВАНИЮ

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

PRODUCT LABEL

CONTENTS PAGE

General warnings

Description of the product

Control panel

User guide for oven

Electronic R programmer instructions (MODELS FI-64/74 MTR-WTR)

Electronic programmer B (MODELS FI-64/74 MTB-WTB)

Touch control o instructions (model FI-64/74 MTLO)

Programmer N instructions (model FI-64/74 MTLN) 11 function full touch electronic programmer instructions (model FI-64/74

MTLM)

Oven functions

Maintenance and cleaning

Removal/assembly of the lateral guides

Removing/mounting the sliding guides (if any)

Replacing the oven light bulb

Instructions for installation

Inserting the oven into the cabinet

Oven electrical connection

Assembly/replacement of the power supply cable

Earth connection

Technical after-sales assistance and spare parts

Tabelle dati tecnici

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

MODELS FI-64 – FI-74

(E) Static

(W) 5 functions

(M) 9 functions

(MTO) 11 functions

(MTM) 11 functions

(MTN) 9 functions

(MTN) 5 functions

TYPE OF PROGRAMMING

(CM) Mechanical timer

(PSC) Mechanical programmer for cooking end time

(OR) Analogue cooking end programming clock

(BT5) Mini electronic programmer

(BT6) Standard electric programmer

(MTO) 11 function full touch electronic programmer

(MTM) 11 function electronic programmer

(MTN) Noalia 9 function electronic programmer

(MTN) Noalia 5 function electronic programmer

GENERAL WARNINGS

Warnings

This appliance is marked in compliance with the European Directive 2012/19/EU.

The crossed bin symbol indicates that the waste product must be disposed of separately from household waste. Take the product to a separate collection centre for electric or electronic appliances or face the penalties provided for by current waste management legislation, or take it back to the dealer when purchasing a new equivalent appliance. For more detailed information, contact the local waste disposal service or the dealer. Dispose of the various packaging materials in compliance with the applicable local Standards.

Installation must only be carried out by qualied

staff in compliance with the local regulations in force and following the indications in this manual. The manufacturer declines all civil and criminal

liability in the case of decient or improper

installation of the appliance. The manufacturer also reserves the right

to make modications to its products that

are deemed necessary and useful, without forewarning.

This household appliance is compliant with the provisions of the European Community Directives

• Low voltage Directive 2014/35/EU

• Electromagnetic compatibility Directive

2014/30/EU

• Regulation (EC) n. 1935/2004

• EU Regulation -66/2014

ATTENTION

do not remove the plate applied on the internal face. It is visible when the oven door is opened and states the product

identication data.

ATTENTION

This appliance must be earthed in compliance with the local standards in force. Failure to comply with that written can compromise the safety of the appliance. Faults caused by installation or improper use are not covered by warranty..

Before installation and use of this appliance this instruction manual must be read thoroughly for correct installation, maintenance and use of the same. Keep it carefully for future consultation. This appliance has been designed for domestic use only for cooking and heating foodstuffs. All other use is considered hazardous. The manufacturer is not liable for any damage caused by improper use of the appliance. In the event of malfunctioning, disconnect the appliance from the mains electricity and contact the After-sales assistance. Never attempt to repair the appliance yourself.

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

Warnings regarding correct use of the oven

• Do not lift or pull the oven with your hands.

• The appliance can also be installed and run in ventilated rooms according to the local regulations in force.

• Use of the appliance is only intended for adults. Ensure it remains out of reach of children.

• The appliance may not be used by children under 8 years of age or by persons with reduced physical, sensory or mental capabilities, or without the experience or knowledge required unless this is performed under direct supervision or after they have been given instructions concerning the safe use of the appliance.

• Children must not play with the appliance.

• Cleaning and maintenance must not be performed by children without adequate supervision.

• The accessible parts become very hot during operation and due to inertia when off. Do not touch it.

• To insert or extract containers, always use suitable protective gloves.

• Do not place inammable material inside the oven. If forgotten, it could catch re after

switch-on.

• Do not sit on or place weight on the open door and do not hang weights on the handle as to do so could damage the product.

• Make sure the ventilation slots are not obstructed.

• During use, do not touch the heating elements.

• Do not touch the appliance with wet or damp hands and feet.

• Do not pull the cable, grip the plug to remove it from the socket.

• Before maintenance or cleaning, switch the oven off and, if just used, wait for it to cool.

BUILT-IN ELECTRIC OVENS

• To prevent any electric shocks, the appliance

must be off before the bulb is replaced.

• Do not clean the appliance using steam

cleaners.

• Abrasive materials or metal scrapers must

not be used to clean the oven door, as they can damage the surfaces. Do not use acid products (lime-scale products) because they can damage the enamelled parts.

• If the power supply cable is damaged, it must

be replaced by the manufacture, by its after-

sales assistance service or by qualied staff.

• Pay attention not to trap power supply cables

from other household appliances in the door when closing.

ATTENTION

NEVER PLACE SHEETS OF ALUMINIUM, TRAYS OR OTHER CONTAINERS ON THE WALLS OR BOTTOM OF THE OVEN. THE MANUFACTURER IS NOT LIABLE FOR ANY DAMAGE CAUSED BY IMPROPER USE OF THE APPLIANCE

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

DESCRIPTION OF THE PRODUCT

BUILT-IN ELECTRIC OVENS

Control panel

Fan-cover panel

Total extraction guides (where envisioned)

Support grids

Sauce collection tray

Grill cooking resistance

CONTROL PANEL

Thermostat Programs selector Timer CM/PSC Clock/BT6 programmer

Power LED Operating LED Clock/OKD touch control programmer

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

Clock/Athena programmer

Clock/OR-PE analogue programmer

Clock/OR-PE electronic programmer

USER GUIDE FOR OVEN

Commissioning

Disconnect the appliance from the mains electricity and remove the accessories from the appliance. Clean them thoroughly with warm water and detergent and put them back in the

initial position. Before using it for the rst time,

allow it to run on empty and at maximum for about 2 hours while ventilating the room well. The combustion fumes of the production residues will be evacuated. Ventilate the environment well during heating.

Power indicator LED

When on, it indicates that the oven is live and on.

Oven operating LED

The LED on indicates the heating phase; the LED odd indicates that the temperature set has been reached. Flashing indicates that the temperature is maintained constant on the value set.

Oven temperature thermostat

Turning the relative knob clockwise, it controls the temperature inside the oven at the desired value between 50° and 270°C

Programs switch or selector

The switch activates the type of functioning desired for cooking. (varies according to models)

Mechanical timer CM

The timer allows an acoustic signal after a preestablished time, independently from cooking. ente dalla cottura.

PSC mechanical cooking end programmer

Allows programming interruption of cooking for a certain amount of time (maximum 2 hours). Programmed functioning:turn the knob clockwise and select the desired cooking time. When time is up, the oven will automatically turn off and an acoustic signal will mark the end of cooking. Manual functioning: to use the oven in a traditional manner without any programming, turn the knob anti-clockwise to the symbol .

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

Analogue cooking end programming clock

Allows a cooking end to be programmed (maximum 3 hours) in the same mode as the PSC by turning the small knob always clockwise. Adjusting the time: pull the knob lightly and turn it clockwise until the clock is set at the current time. Manual operation: Turn the knob clockwise until the hand reaches the manual symbol.

The oven cannot work if the programmer is at O

ATTENTION

ELECTRONIC R PROGRAMMER INSTRUCTIONS (MODELS FI-64/74 MTR-WTR)

Adjusting the time

To adjust the time, briey press the knob 4 times

until the “CLOCK” icon ashes. Therefore, increase or decrease the time in steps of 1 minute, turn the knob clockwise or anti-clockwise and the minutes hand moves by 1 minute clockwise or anti-clockwise. After 10 seconds from the last adjustment, the electronic timer automatically exits the time adjustment mode.

This timer displays the time and operation of the oven. By operating on the push knob it is possible: to adjust the time, program the start and end time of cooking, set the alarm.

Manual cooking

At rest, the timer allows manual cooking by operating on the oven master switch (outside the device). After having supplied the mains power supply to the timer, wait approx. 2 seconds before the relay is energised.

Programming the cooking start and end time

Programming the cooking start time: press the

knob once briey until the “START TIME” icon ashes. Turn the knob clockwise until the desired

cooking start time is displayed. The “START TIME” icon continues to ash for 10 seconds from the last rotation. If the knob is not turned or pressed within this time, the hands go back to displaying the time and the program is annulled. If the knob is pressed, the Cooking Start time is memorised (“START TIME” icon on with

xed light), as long as at least 1 minute of delay

has been set and you pass to setting the Cooking End time (the“END TIME” icon goes from off to

ashing). Cooking will start when “Cooking Start

Time Set = Current Time”. Programming the cooking end time allows immediate start-up and to end cooking in an automatic manner on the basis of the programmed time. Programming the cooking end time: press the

knob twice briey until the ““END TIME”TIME” icon ashes.

To increase or decrease the cooking time, turn the knob clockwise or anti-clockwise and the minutes hand moves by 1 minute clockwise or anti-clockwise. Flashing of the “END TIME” icon continues for 10 seconds from the last rotation. The program

can be conrmed by pressing the knob as long

as at least 2 minutes of cooking have been programmed.

On conrming the program, cooking is started

and the acoustic alarm is automatically activated.

Cooking will end when “Cooking

End Time Set = Current Time”. To display the program set, press and release

the knob briey and, at the same time, the clock

hands and icons display the program set. At the end of cooking, the “END TIME” icon ashes and the alarm emits acoustic signals. To annul the program before the end, press the knob for 3 seconds; the program will be annulled and the timer goes back to manual cooking mode.

Minute minder programming

Programming the Minute Minder allows an alarm at the end of a programmed time without

activating cooking. To program an “alarm” without starting cooking, press the knob briey 3 times until the “ALARM” icon ashes. Turn the knob and

the setting of the Minute Minder is identical to that of the Cooking End time. The Minute Minder can only be used when there is no program in progress.

Signalling and blackout

The timer signals every power cut by the ashing “CLOCK” symbol. In this case, press the knob briey to disable the signal.

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

ELECTRONIC PROGRAMMER B (MODELS FI-64/74 MTB-WTB)

Activation and adjustment of the time

Once the current is connected, the ashing symbol and 12:00 appear on the display; the h:min symbol appears. By touching one of the three symbols SEL

all signals stop ashing. Time adjustment is now

possible. By maintaining pressure constant, the increase is continuous. After a few seconds the

time is xed.

Selecting/annulling programs

Clock

Timer

Oven on

The programs are selected by pressing the SEL symbol and scrolling the menu The Man symbol indicates that the oven is in manual mode. The symbol performing a program. To annul a program, take the values set to 0:00.

indicates that the oven is not

Cooking time

Cooking end time

Decrease num.

Increase num.

Man

This programmer functions with touch system, operate on the commands by exerting slight pressure in the area indicated by the symbols.

Automatic

Manual

Safety lock

Manual operation

The programmer must be activated, the Man symbol illuminated and operation performed on the knobs. The TIMER function can be used in all cases.

Semi-automatic operation (cooking duration programming)

Operate on the SEL symbol until the appearance

of the ashing

symbol, set cooking duration by operating on the

symbols. The remains xed and the

symbol, the actual time and the Auto symbol appear. Turn the knob to the values desired. An acoustic signal indicates the end of cooking, the

Man symbol starts to ash and the oven turns off.

To stop the acoustic signal, operate on any of the symbols. Press SEL again to exit programming.

, numbers 0:00 and h:m

Semi-automatic operation (cooking end programming)

Touch the SEL symbol until . appears. By

operating on the set the desired cooking end time. After a few seconds, the the clock time re-appears and the Auto and symbols switch on. Now turn the two knobs to the desired temperature and cooking time. When the set time is reached, the acoustic signal indicates the end of cooking, the Man

symbol starts to ash and the oven turns off. To

stop the acoustic signal, operate on any of the symbols. Press SEL again to exit programming. Programming can be annulled by taking the cooking time to 0:00.

symbol switches off,

Automatic operation (deferred cooking start setting)

Operate on the SEL symbol until the appearance

of ashing set the desired cooking time (using

). Still using SEL go to the ashing symbol

and set the desired cooking end time. After a few seconds, the symbol switches off the clock time re-appears and the Auto symbol switches on. Turn the knobs onto the desired functions and temperatures. The oven remains off and will turn on automatically according to what you set. When the set time is reached, the acoustic signal indicates the end of cooking, the Man symbol

starts to ash and the oven turns off. Turn the

knobs to the off position. To stop the acoustic signal, touch any of the symbols. Press SEL again to exit programming. Programming can be annulled by taking the cooking time to 0:00.

Acoustic signal

To stop the acoustic signal, touch one of the three boxed symbols adjust the volume of the signal to three levels, as follows. Operate on the SEL symbol until the letter L appears, followed by the level currently set (from L1 to L3). Touch the symbols to set the desired level

SEL . It is possible to

Child safety or accidental contacts

It is a function that can block access to the functionality of the electronic programmer keys both when the oven is running and when the oven is off. When, by operating for approx. 5 seconds on the symbol this function activates, (the symbol lights up), this prevents children or other persons from pressing the programmer keys and modifying the previous program or from starting the oven that is off. Operate in the same way to deactivate it. In manual position (Man), lactivation of the lock does not allow use of the oven. Consequently, with the timer function, the lock cannot be activated. NOTE: the lock must be deactivated for access

to a set program.

This remains active even after a power

cut, which switches the programmer off.

Timer function

Operate on the SEL symbol until the ashing

symbol, the numbers 0:00 and the min:sec symbols appear. By touching the symbols, the desired time is set. The programmer will start the countdown. On reaching the time set, the acoustic signal is triggered. Touch any symbol indifferently to stop the acoustic signal. To annul this function, take the timer to 0:00. This function can be used for manual cooking.

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

Touch control O instructions (model FI-64/74 MTLO)

This programmer functions with touch system,

On/Off

operate on the commands by exerting slight pressure in the area indicated by the symbols.

Cooking starts

Programs stop

Temperature adjustment

Increase numerations

Decrease numerations

Core probe

Scroll down

Scroll up

Fast heating

Times adjustment

Light On/Off

Safety lock

Oven switch-on/off

To switch the oven on or off, lightly press and hold on the symbol for approx. one second. . The actual time will appear on the display. This can be performed independently from whether the child safety function is activated or not .

Time adjustment

At the time of the rst connection of the current, the ashing numbers 0:00 appear on the display.

The oven cannot be used without having adjusted the time. To adjust the time, operate on the and symbols. The time is xed after approx. 7 seconds when there is no intervention. In the event of a temporary power cut, the data memorised remain set for approx. 45 seconds. To modify the time set, press the and symbols

simultaneously until the numbers start to ash. If

the time is to be read in 12 hour am/pm mode, press

and simultaneously for 5 seconds..

Selecting programs

By pressing the symbols the oven functions menu can be scrolled.

The current function will ash for a few seconds

and the set temperature assigned to the function will appear (some functions do not envision adjustment of the temperatures). The symbol

and the ashing PAUSE wording indicate that the oven is ready to start in the mode selected, but cooking has not yet begun.

cooking is resumed. To modify the parameters (functions, temperatures, etc.), follow the previous indications by pressing at the end on

to conrm.

Modication of the temperature

assigned to the function

To modify the temperatures dened for each

function, just touch the symbol and operate on and adjusting the temperature. After

a few seconds, the new value is xed and stops ashing. Press to resume cooking. To go back

to the pre-set temperature, operate in the same way. To change the temperature set by the manufacturer denitively, press on the symbol until a warning beep is heard (approx. 5 seconds)

and the temperature numbers stop ashing.

Manual operation

Once the function has been selected, by operating

, icooking starts with the temperature set

on indicated on the display. The PAUSE symbol disappears and the timer starts, which indicates the time passed from the start of cooking. This will continue until interrupted manually or the maximum limit pre-set has been reached. The maximum cooking time limit that can be reached varies according to the temperature set at the following values: For temperatures: from 50 – 120 °C max time

10h; from 121 – 200 °C max time 6h; from 201 – 250 °C max time 3h.

In semi-automatic and automatic cooking, the same is interrupted automatically as per previously set parameters.

Pause, modify or cooking end functions

By pressing on during cooking, this is interrupted and the PAUSE symbol ashes. By touching again, all indications on the display disappear. The display will indicate any residual temperature. By pressing the rst time, the last setting interrupted appears and pressing it again,

Semi-automatic operation (cooking duration time programming)

This function allows the desired cooking end time to be set, with immediate start-up of the same by setting the desired cooking duration time. In this case, the food probe cannot be used (where envisioned). To activate semi-automatic cooking, select the desired oven function from the menu and adjust the cooking temperature, if necessary. By touching the symbol 0:00 of the timer will

start to ash. Adjust the desired cooking duration

time (the AUTO symbol appears) and press on , cooking starts immediately and the time it will end appears on the display. An acoustic signal will inform of end of cooking, press on to interrupt the signal. To interrupt cooking, press on PAUSE, will appear. Press a second time on to annul the program.

Semi-automatic operation (cooking end programming)

In this case, it is possible to set the desired cooking end time with immediate start-up, without indicating the duration. In for the previous function, the food probe cannot be used (where envisioned). To activate cooking end, select the desired oven function from the menu and adjust the cooking temperature, if necessary, as previously described. Press the , symbol twice; the cooking end time appears, which corresponds to the time of day. Operate on and to program the desired cooking end time. Press on , the PAUSE symbol

stops ashing and the oven starts cooking.

To interrupt cooking, press on , PAUSE, will appear. Press a second time on to annul the program.

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

Automatic operation (with deferred cooking start setting)

This function allows cooking duration to be programmed, also setting the start time. Also in this case, it is not possible to use the food probe (where envisioned). To activate automatic cooking, select the desired oven function from the menu and adjust the cooking temperature. By touching the symbol

0:00 of the timer will start to ash. Adjust the

desired cooking duration time (the AUTO symbol will appear). Press on the , symbol, the ashing cooking end time envisioned by the duration time entered appears. Operate on and to set the desired cooking end time. Press to activate programming. The function, temperature and cooking end time symbols appear on the

display. A ashing arrow near to the temperature

will indicate that cooking has started. An acoustic signal will inform of end of cooking, press on to interrupt the signal. To interrupt cooking, press on , PAUSE, will appear. Press a second time on to annul the program.

Timer function

With this function it is possible to activate a timer that will signal when the time set has expired. Press lightly several times on the , symbol until the ashing symbol appears along with 0:00 on the timer. Adjust the desired minutes by operating on

and . When the time set has passed, an acoustic signal, which will last for approx. 7 minutes, will inform you that the time has expired. To stop the acoustic symbol, operate on or .

Alarm clock function

Premere leggermente più volte sul simbolo no a che non appare lampeggiante il simbolo assieme all’orario del giorno. A questo punto con

e regolate l’ora del giorno in cui desiderate essere avvisati dalla sveglia. Trascorso il tempo impostato un segnale acustico che durerà per circa 7 minuti vi avviserà che il tempo è scaduto. Per fermare il segnale acustico agire indifferentemente su o .

Core probe function (in models set-up)

The Core Probe is a sensor that can be connected inside the oven and inserted inside the dish to be cooked. The use of this probe allows automatic interruption of cooking when the inside of the food reaches the desired temperature. To activate it, select the desired function and, if necessary, modify the temperature that appears

by default (see the “Modifying the temperature

assigned to the function” paragraph). Press the key. The pre-set value of the programmed temperature for the probe appears

ashing in the two numbers on the right of the

timer (with this function, the timer display is used to show the core probe temperatures). The word AUTO. also appears. Set the temperature desired for the inside of the food from the values between 20/99°C by operating on the or . Press the GO, key PAUSE switches off and cooking starts. The current temperature is visible on the numbers on the left while the temperature that you have set is visible on the right-hand numbers of the timer display.

Fast heating function (for some functions only)

This function allows faster oven pre-heating. After having selected the desired cooking function, press the button. The elements most suitable for quickly reaching the set temperature are activated and the symbol can be seen on the display, which will disappear as soon as the temperature is reached. The program will also emit a warning sign. At this point, the system will state the previously set functions as active. Fast heating cannot be activated with the GRILL function, when the difference between temperature set and that to be reached is lower than 50°C and when the temperature to reach is lower than 100°C.

Temperatures display

The 5 bars near to the temperature set indicator show the temperature level reached. The arrow

facing upwards and ashing signals that the oven

is heating up. After cooking has been interrupted, while the temperature inside the oven is above 60 °C, a ashing downward arrow and hot will appear on the display and will remain until the temperature drops below 60 °C. Acoustic signal: the acoustic signal continues to ring at the end of a program for approx. 7 minutes. To stop it, press or indifferently. It is possible to adjust the volume of the signal to three levels: in the STOP position, operate on the symbol, pressing it for approx. 5 seconds until the tone level currently set appears. Operate on the symbol again to set the desired level.

Child safety

This function allows access to the functionality of the electronic programmer keys to be blocked, both when the oven is running and when the oven is off. By operating on the symbol for 2 seconds, this function is activated. This prevents children or other persons from pressing the programmer keys involuntarily. Thus modifying the previous program or from starting the oven that is off. Every programmer signal that intervenes while the oven is on, when the safety lock is activated, can be eliminated by pressing any of the boxed keys. The safety lock will remain active NOTE: The lock must be deactivated for access

to a set program.

Command tones

It is possible to modify the type of sound emitted when operating on the commands. In the STOP, position, slightly press the symbol for approx. 5 seconds. Operate on the symbol

again to select “bt” (beep tone), “c” (click tone) or “nt” (no tone)

Energy saving

To limit the waste of electricity, the PS (Power Save) function can be used. This function switches the oven off completely if, in absence of cooking functions activated, there is no intervention with any command. Press and hold the symbol for approx. 5 seconds PS on will appear. The function is now active and the oven will automatically turn off after approximately 1 minute. Operate on the

symbol to switch it back on..

Error signals

When situations occur that prevent normal operation of the oven, the device informs this with a series of signals, such as: Err1: communication error – Err2: PT1000 (probe) open circuit – Err3: PT1000 (probe) closed circuit – Err4: temperature too high on the display – Err5: temperature too high on the power board – Err6: fault in the display – Err7: fault in the power board – Err8: no heating is detected. For the Err4 and Err5 errors, switch the oven off and allow it to cool for a few hours and then try to use it again. If the error persists, call the technical after-sales assistance. If any of the

other errors are present, the authorised aftersales assistance must be informed.

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

Programmer N instructions (model FI-64/74 MTLN)

Switching on

On commissioning, the display ashes and the

time of day starts from 12:00. Make sure that the left knob is in the off position and then press the right knob to access the oven functions. If the selector is not at off, by pressing the right knob, a warning signal is activated.

ISetting the time

When the oven is in Stand-by mode, press the right knob to access the time setting menu (the

time ashes). Turn to the right to increase and

the left to decrease. Initially, the hour increases

or decreases at the rst step, at number 6 the speed increases, the minutes ash indicating that

the time has been set.

After 4 seconds from the last modication, the

menu is exited automatically, the hours and

minutes ash indicating that the time has been

set. After another 4 seconds, press the right knob; it returns to stand-by.

Right knob functions

Depending on the position of the cooking mode selector (represented by the left knob), pressing the right knob allows access to different menus. When the cooking mode selector switch is off, it

is possible:

- Modify the time;

- Modify the timer;

- Modify the button acoustic signal tone. When the cooking mode selector switch is on, it

is possible:

- Modify the functions of the oven, except for the special defrosting and oven light functions;

- Modify the timer;

- Modify the duration of the functions;

- Modify cooking stop;

Method of use

To start cooking, turn the knob to the desired cooking function (the default temperature is already set and is shown on the display). When the selector is in the OFF position, the display shows the time but the oven temperatures and programs cannot be selected. In this way, only the timer is active. The cooling fan is off when the temperature of the oven cavity is lower than 110 degrees.

Oven light mode

When the oven light mode is active, the time of day can be seen on the display but temperatures and programs cannot be selected. Also in this case, the cooling fan is off when the temperature of the oven cavity of lower than 110 degrees centigrade.

Defrost mode

When defrosting mode is selected, the cooling fan is off and the ventilated function is not active.

“dEF” and a fan icon can be seem on the display.

Manual cooking mode

Turn the knob to select the desired function; the temperature is already pre-set. The display shows the icon of the cooking mode

selected. The temperature ashes and can be modied by pressing and turning the right knob.

Before the oven reaches the desired temperature, the effective temperature inside the cavity

is displayed along with the ashing pre-set

temperature, if the right knob is pressed.

Stop cooking

The selector must be moved to the OFF position to stop cooking. When the oven is switched off, the program selected is automatically cancelled.

Programmes

Annulling programs

The time programmed for the timer, the automatic cooking and the temperature of the oven can be annulled by:

- Clear Function (the display shows the time and all programs are cancelled)

- Oven light

Timer

This function does not interact with the oven and is always available independently from oven status (on or off). To select the time, turn the right

knob to obtain the desired time (the rst minute is

displayed as seconds). After 4’(or pressing the right knob), the bell icon lights up and the countdown begins. The acoustic

signal and the ashing icon indicate the end.

Press the right knob to stop.

Automatic or semi-automatic cooking

Semi-automatic (allows cooking duration to be set)

After having selected a cooking program, the display shows the corresponding icon. Press the right knob 3 times to access the menu to modify. The icons switch on. Select a time from 0:00 to 23:59 by turning the right knob. After 4 seconds without any action, the value is set. During cooking the display shows the temperature of the oven. By pressing the right knob 3 times, the remaining time is displayed. During cooking, the icons indicates the increase of the temperature and

the program (time can be modied also during

cooking). At the end, the display shows END, the

ashes and an acoustic signal is emitted by the

button. By pressing the right knob, the signal stops. Turn towards OFF to stop cooking or select another cooking mode.

Automatic (allows cooking duration and end to be set)

Select the duration of the cooking time as described above. Successively, press the right knob 4 times. The symbol the icon switches on. The cooking end can be seen on the display. By turning the right knob, it is possible to set when cooking must end. In Stand-by, the display shows the temperature selected and the symbol The icon corresponding to the cooking mode selected also lights up. When cooking starts, the

and symbols switch on. Instead, the symbol shows the temperature increase of the oven with respect to that initially set. At the end of cooking, the display shows END, the emitted. Turn the selector to OFF to stop or select another mode.

remain on. The icon

icon

switches off and

symbol ashes and an acoustic signal is

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

On status

Generally, in all modes except OFF, the cooling fan is operational. When a cooking ode is selected and the oven is off, the cooling fan is also off if the temperature of the oven is below 110 degrees.

Button

The button alarm sounds if the timer of automatic cooking program have terminated. The signal is switched off by pressing the knob on the right or waiting 7 minutes.

Errors code (when the display shows one of the following codes)

F000: oven temperature sensor short circuit F001: temperature sensor open circuit Ftop: reading error of the cooking mode selection.

Blackout

If there is a drop in voltage, all parameters are removed. On switch-on, the oven uses the default settings.

Diagnosis procedure

The oven has a specic test in the software to test

all elements. This test should only start-up on commissioning.

BUILT-IN ELECTRIC OVENS

11 function full touch electronic programmer instructions (model FI-64/74 MTLM)

KEY 1 on/off/resume

KEY 2 menu selection

KEY 3 start/pause

KEY 4 +/ temperature

KEY 5 -

KEY 6

conrm/reset oven light/

system time

Detail of display areas

System clock display/ setting area. (position on the display: in the top centre)

Time programming and progressive cooking time display area. (position on the display: in the top left)

automatic cooking end time

timer

alarm clock

cooking duration time

Cooking mode display area. (position on the display: central)

Chamber centre temperature display/ setting area and temperature graphics. (position on the display: in the top right)

keys lock (special safety function)

temperature selection indicator

temperature increase/ decrease

internal temperature status graphics

(position on the display: central on the right)

cooking stand-by mode/ cooking not active indicator

active cooking mode area

automatic cooking

manual cooking progressive time

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

Special functions indicators

“OVEN LIGHT” indicator (position on the display: central)

“PAUSE” indicator

(position on the display: in bottom left)

“DEFROST” indicator

(position on the display: in bottom left)

“FOOD WARMER” indicator

(position on the display: in bottom left)

“FOOD PROBE” indicator, in the

models where envisioned (position on the display: central on the left)

Cooking functions that can be selected

Circular Resistance + Radial Fan 180°C

Circular Resistance + Bottom Resistance + Radial Fan (200°C)

Circular Resistance + Top Resistance + Radial Fan (180°C)

Grill Resistance + Radial Fan (°C)

Bottom Resistance + Radial Fan (140°C)

Circular Resistance + Top Resistance + Radial Fan (180°C)

Top Resistance + Bottom Resistance (180°C)

Bottom Resistance (150°C)

ATTENTION

• All the functions are accompanied by the activation of the internal light bulb . The light remains on for 3 mins. and then it switches off automatically.

• Possible temperature range 50-250 °C

Switching on

Commissioning/restoring power cut

All icons remain on for 2 secs. to verify oven operation.

Whether it concerns the rst connection to the

mains or restoring voltage, the system time is as

shown in the gure, with ashing numbers-

To continue, the system time must be set (see reference paragraph).

If the cooking mode is interrupted due to a power cut, the oven maintains all the information regarding the cooking (blackout mode).

Once the oven system time has been set, the acoustic signal blocks and goes to PAUSE mode reference paragraph).

(see

Adjusting system time

The system time (clock) is based on the type of mains power supply (50Hz or 60Hz). Time adjustment takes place with oven OFF:

Grill Resistance (°C)

Defrost

Food warmer

• Hold key 6

the digits of the hour ash on the display. Use

keys 4 and 5 to set the value.

• For the acquisition of the time set, it must be

conrmed using key 6 .

• Perform the same procedure to set the minutes.

down for at least 3 seconds:

If the oven is OFF, the control then shows just the system time, dimming after 1 min. If the oven is in blackout mode due to a lack of

voltage, the time digits already ash: operate on

keys 4 and 5 to set the time as specied above. The oven is activated by pressing key 1 ON/OFF

for at least 2 sec and switches off by touching the same key. If no keys are pressed after switch-on, the oven deactivates automatically after 1 min. (accidental switch-on control). Oven ON: single acoustic signal. Oven OFF: double acoustic signal. If the oven is off in low consumption mode

(dimmed display light), at the rst touch of a key,

we have RESUME mode. The low consumption mode is re-enabled automatically after one minute.

ATTENTION

Oven switch-off annuls all cooking programming and times set.

Accidental switch-on control

It is an automatic oven switch off signal. This takes place after oven switch on using key 1 ON/

and 1 min of commands inactivity, i.e. no

OFF function selected and activated. After 1 minute, a double acoustic signal will inform of switch-off.

Oven on: in stand-by for commands

By pressing key 1 ON/OFF the oven switches on while waiting to receive settings on the desired cooking function. Ventilated cooking is the default function (Circular Resistance + Radial Fan) with pre-set temperature equal to 180°C.

Using key 2 menu the functions can be scrolled in this order of display:

• cooking functions menu;

• oven temperature;

• cooking time programming;

• timer;

• alarm clock;

When scrolling the functions, the relative icons

ash. If the function is not conrmed or modied

within 7 secs, the selection is deactivated. From

oven “on in stand-by for commands”, if commands

are inactive for a time exceeding 5 minutes, the oven switches off automatically.

ATTENTION

It is possible to pass from oven “in cooking mode” to the “on in stand-by for commands” status by pressing key 1 ON/

OFF

. Pressing the key again, switches

the oven off denitively.

Cooking functions menu

After oven switch-on using key 1 ON/OFF , it is possible to directly access the choice of cooking functions by pressing key 2 menu . The central

icon and the cooking functions start to ash.

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

Using keys 4 and 5 it is possible to scroll

through all cooking functions available (see “

COOKING FUNCTIONS TO BE SELECTED”): the relative segments activate.

Once the desired function is highlighted, conrm

with key In each case, after 7 seconds of inactivity of the

commands, the function selected is conrmed automatically (auto-conrm).

At this point, to start cooking, conrm

everything using key 3 START (see reference paragraph)

The oven starts the pre-heating phase. The light inside the oven switches on icon basis of the cooking function selected, the default temperature appears and the upward temperature icon starts to ash. The progressive cooking time in manual mode is displayed. The respective icon

. The cooking pan

sis activated and starts to ash. On the

starts to ash (see gure).

BUILT-IN ELECTRIC OVENS

ATTENTION

the control has time limits for continuous cooking, with the following safety limits:

- 250°C max 3h

- 120-195°C max 8h

- 200-245°C max 5h

- up to 120°C max 11h

Residual heat

If HOT appears in the top right of the display, it means attention must be paid not to touch the inner parts of the oven, even if the latter is off. HOT is displayed after the oven is switched off and remains active until the chamber temperature has dropped below 50°C.

At cooking end, press key 1 ON/OFF and the

oven remains in “on in stand-by for commands”

mode. Pressing the key again, switches the oven

off denitively.

Temperatures display

Activated following oven switch on, key 1 ON/OFF

along with the default ‘ventilated cooking’ mode. If cooking is started, the display shows the following information:

- pre-set temperature (default);

- icons: thermometer, upward arrow and

progressive temperature graphics;

- “cooking pan” icon

lights up;

Setting and modifying the temperatures

The temperature can be modied at all times,

after the selection of a cooking function, by simply using key 4 .

On the display, the temperature and the corresponding icon ash.

Use keys 4 and 5 to set the desired temperature and conrm using key 6 . In each case, after 7 seconds of inactivity of the commands, the temperature selected is

conrmed automatically (auto-conrm).

Alternatively, it is possible to access the

temperature modication using key 2 menu

Go onto the temperature function: the step is highlighted by the ashing temperature icon .

To select the desired temperature, use keys 4 and 5 and then conrm using key 6 or after

7 sec the value will be auto-conrmed.

Pre-set temperature

It is possible to modify the pre-set temperature assigned for every function.

Using key 4 (or key 2 menu ), go to the

temperature modication mode and set the new

pre-set temperature.

While the display ashes (i.e. within 7 sec), conrm the value holding key 6 down

least 3 sec. The next time the oven is switched on, there is a new pre-set temperature

for at

Pre-heating the oven

Once the cooking function and temperature have been selected, using key 3 START the cooking mode is entered and the pre-heating phase commences.

The upward temperature icon starts to ash

and the status graphics temperature reached by the oven cavity. Once all

of the graphic bars have been lled, a prolonged

acoustic signal informs that the temperature set has been reached inside the oven and the upward

temperature icon stops ashing.

The stabilised temperature icon appears in its place . At this point, the oven maintains the temperature

set constant inside the cavity. If modications

are made to the temperature of the oven, the respective upward temperature downward temperature icons are activated.

highlights the

and

can be performed with the oven in cooking mode.

icon is xed and the loads are off but

The other settings not reset.

After having conrmed any modications to the

cooking parameter and/or displayed the cooking status, the pause must be deactivated in order to continue. Therefore, press key 3 START pause. The icon is deactivated. Cooking is thus resumed and all of the automatic programming, progressive cooking time and displays are activated.

ATTENTION

The PAUSE function does not obstruct the TIMER while it blocks automatic programming of time (AUTO functions).

Furthermore, the pause function is activated automatically in the following cases:

• previously conrmed cooking function change;

• restore missing voltage with oven in cooking mode;

and ALARM CLOCK functions

again to exit the

Special functions

Start/pause functions

The key 3 START as already described, is active after having selected a cooking function

and allows conrmation of all cooking settings

in automatic programming mode; practically, it starts cooking (START function). The PAUSE function, represented by the icon, is always activated with key 3 START

and this

Oven light control

Standard hinge

Switching the light on is considered a special function: it is not selected among the cooking functions. The light can be switched on and off any time, even with oven off using key 6

in programming phase and/or modication of a

(except when

BUILT-IN ELECTRIC OVENS

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS

function). In all cases, the light switches off automatically after 3 minutes. The oven light is controlled by a micro-switch on the door, which detects opening and closing. Opening of the door is signalled by the wording

on the clock display and the light switching on. This takes place also with the oven OFF. If the oven is in cooking mode, opening the door deactivates the Radian Fan and the Circular Resistance where envisioned, thus preventing the steam produced from hitting the user directly and there is a great heat loss.

Soft-closing hinge

The oven light is automatically activated for three minutes by pressing the START key to enable a function; in case of inactivity it goes off after 3 minutes. The light will remain on for three minutes after the end of pre-heating.

Key function (child safety)

The key function prevents/freezes the functionality

of the touch keys. This is to prevent modications

to cooking programs and/or accidental switchons (child safety). The key function can be activated/deactivated at any time by pressing key 5 and key 6 together for at least 3 seconds . In the event of activation, the

ash for 3 secs. and then remains active. At this point, the function is conrmed.

At every action successive to activation of the function, the 3 seconds to remind of the safety status. To continue, deactivate the key function. The key function can be activated/deactivated also with oven off.

icon starts to

icon ashes for

Food warmer function

It is a function that keeps the foods warm at a recommended temperature of 80°C: it is selected using key 2 traditional cooking functions menu;

• go to the function indicated by the icon

• conrm using key 6

automatic after 7 sec;

• to activate the function, press key 3 START

• it is possible to modify the temperature slightly within the range of 60°-90°C;

• the timer and automatic programming functions can be activated;

or conrmation will be

;

Defrost function

It is a function that does not envision the use of resistive elements, but just the internal radial fan:

• it is selected using key 2 in the traditional cooking functions menu;

• go to the function indicated by the icon

• conrm using key 6 or conrmation will be

automatic after 7 sec;

• to activate the function, press key 3 START

• the possibility of changing the temperature is not envisioned and the relative display is off;

• the timer and automatic programming functions can be activated;

;

Food probe (in the models where envisioned)

It is an instrument that allows accurate and constant control of cooking, and this takes place through a probe that detects the temperature inside the food. It accurately guarantees that the food is cooked completely inside. Connect the probe to the relevant socket (jack) inside the oven and introduce the needle probe horizontally and to the centre of the food; try not to touch bone and fat (see reference paragraph) The following displays are envisioned:

• the reference icon is activated ;

• on the time programming display there is (see

gure);

• the set temperature displayed on the left (65°C default);

• the real temperature of the food is shown on the right, i.e. that measured by the probe (e.g. 20°C);

The set temperature can be modied using key 2

within the range of 65°C - 85°C. Go onto the set vale and use keys 4 and 5 to modify the temperature.

Conrm using key 6 or conrmation will be

automatic after 7 sec. Once the real temperature of the food reaches the set temperature, the oven switches off automatically. An intermittent acoustic signal informs cooking has been performed. With this function it is not possible to program

cooking times. While it is always possible

to set the timers

ATTENTION

Always use the probe supplied with the oven.

Insert the needle probe fully home until it reaches the centre of the product to be cooked. The sensor should detect: The temperature reached at the core of the product. The more accurate the positioning of the needle probe, the more accurate cooking will be.

The more accurate the positioning of the needle probe the more accurate cooking will be.

The meat probe is made up from a needle probe with grip that detects the temperature and a jack-type attachment, inserted into the relevant connector to dialogue with the electronic control.

ATTENTION

During cooking or at the end of cooking, the cap is hot. If the probe is to be inserted or removed, use relevant gloves or wait for the oven to cool down..

+ 72 hidden pages