Zibro S125, SS95, S245, S185 user manual

S95 - S125 - S185 - S245

OPERATING MANUAL

ISTRUZIONI D’USO

GEBRUIKSAANWIJZING

INSTRUKCJA OBS

KULLANIM KILAVUZU

ŁUGI

Dear Sir, Madam,

Congratulations on the purchase of your airconditioner. You have acquired a high quality

product that, if used responsibly, will give you many years of pleasure. Please read these

instructions for use first in order to ensure the maximum life span of your airconditioner.

On behalf of the manufacturer, we provide a 24-month guarantee on all material and

production defects. Please enjoy your airconditioner.

Yours sincerely,

PVG International b.v.

Customer service department

1. READ THE DIRECTIONS FOR USE FIRST

2. IN CASE OF ANY DOUBT, CONTACT YOUR DEALER.

CONTENTS

A Specifications page 4

B Parts page 4

C Before use page 6

D Installation instructions page 7

E Instructions for use page 14

F Maintenance page 18

G Protection page 18

H Problem solving page 20

I Guarantee conditions page 21

A SPECIFICATIONS

m3/

000

OP *

Model

EE Class

EER *

OP Class

To be used as indication, subject to modifications.

S95 S125 S185 S245

ooling capacity * kW 2.7 3.5 5.3 7.0

.8 2.8 2.8 2.9

eating capacity kW 2.8 3.8 5.7 7.6

.2 3.2 3.4 3.5

ehumidification capacity (max) ** Ltr/day 19 24 36 48

ower consumption cooling kW 0.88 1.17 1.9 2.6

ower consumption heating kW 0.88 1.17 1.9 2.6

ains Volt/Hz/Pf 220-240/50/1 220-240/50/1 220-240/50/1 220-240/50/1

urrent (nom) A 3.6 5.1 8.7 12.8

irflow (max)

or rooms up to

imensions indoor unit (WxDxH) mm 718x180x240 770x180x240 1033x202x313 1033x202x313

Dimensions outdoor unit (WxDxH) mm 669x296x506 769x328x552 829x328x552 929x372x652

Weight indoor unit kg 7 7 14 14

Weight outdoor unit kg 24 32 42 56

Refrigerant/charge type/gr R407C/540 R407C/900 R407C/1680 R407C/2300

Noise level indoor unit (max) dB(A) 36 38 43 47

Noise level outdoor unit (max) dB(A) 50 50 60 54

Operating range ºC 10-40 10-40 10-40 10-40

Unit protection indoor IP IP X0 IP X0 IP X0 IP X0

Unit protection outdoor IP IP X4 IP X4 IP X4 IP X4

DDD

* Conform EN 14511 ** Moisture removal at 32°C, 80% RH

Defective electrical devices and batteries must be kept separate from household waste. Ensure that there is effective recycling where possible. Ask you local council or dealer for expert advice on recycling.

B PARTS

INDOOR UNIT

Air inlet

Front panel

Emergency button

Display

Air outlet

Vertically

adjustable vane

Horizontally

adjustable vane

OUTDOOR UNIT

Active carbon

filter (optional)

Healthy air filter

(optional)

Air filter

Remote control

Air inlet

Drainage hose

Note: Condensation is drained during COOLING or DR

Pipes and power

cable

Air outlet

YING

The diagrams in these instructions are based on a standard model. The air conditioner you have pur

chased may be a different model.

C BEFORE USING

Check and adjust the following before using the air conditioner.

Adjusting the remote control

he manufacturer has NOT preset the remote control heating or cooling options. The arrow for ‘Heat’ or ‘Cool’ on the remote control display will flash after the batteries in the remote control have been replaced. Depending on the type of air conditioner that you have purchased, the remote control can be adjusted as follows: Press any button while the ‘Heat’ arrow is flashing. This sets the heat pump. Press any button while the ‘Cool’ arrow is flashing. The setting has been entered for cooling only. If you do not press any button within 10 seconds, the remote control is automatically preset to the heat pump. Type S95, S125, S185 and S245 are fitted with a heat pump.

The Heat function can NOT be adjusted with the remote control when the remote control has been preset to Cool Only.

Safety regulations

• Use the correct power supply (see type plate) in order to prevent serious faults, hazards or fire.

• Ensure that the circuit breaker or plug does not become dirty. Connect the plug/circuit breaker to the

power cable correctly. Insufficient contact may cause an electric shock or fire.

• Do not switch the unit off with the circuit breaker or by pulling the plug out of the socket. This may

produce sparks that could start a fire.

• Do not tie any knots in the power cable or pull the power cable. This may damage or break the cable,

causing an electric shock or fire.

• Never insert sticks or any similar object into the unit. The ventilator rotates at high speed and may

cause injury.

• It is detrimental to your health to remain in the cold airstream for an extended period of time. We

recommend that you allow the airstream to flow freely into the room, without obstruction.

• If a fault occurs, switch the machine off with the remote control before pulling the plug out of the

socket.

• Do not carry out any repairs. Incorrect repairs may cause electric shocks, etc.

• Do not place gas burners or ovens in the airstream.

• Do not operate the buttons with wet hands.

• Do not place any objects on the outdoor unit.

• The user is responsible for the earth connection. This must be fitted by a recognised installer in

accordance with local regulations and ordinances.

D INSTALLATION INSTRUCTIONS

Installation diagram

Distance to the wall must be a minimum of 50 mm.

Distance to the ceiling must be a minimum of 50 mm.

istance to the wall must be

D a minimum of 50 mm.

Distance between the air inlet and the wall must be a minimum of 250 mm.

Distance between the air outlet and the wall must be a minimum of 500 mm.

- The diagram above is a simplified illustration of the unit and may differ from the unit that you have purchased.

- The installation must be carried out by a recognised installer and connected in accordance with national regulations.

Distance between the air inlet and the wall must be a minimum of 250 mm.

min. 250 mm.

Connecting the power cable

Wiring between the indoor and outdoor unit:

1. Remove the plastic cover from the indoor unit.

2. Use the circuit diagram (attached to the indoor unit) as a reference for the connections.

. Replace the cover, “B” on the outside.

Select the correct location

No obstacles in the vicinity of the air outlet. The air stream must be allowed to reach the entire room unhindered. It must be possible to install the pipes and drill the hole in the wall at an accessible location. Ensure that there is sufficient distance between the unit, ceiling and wall (refer to Chapter D). It must be possible to remove the air filter easily. The unit and remote control must be placed at least 1 metre from televisions, radios, etc. Strip lights may cause faults. Ensure that there is sufficient distance. Do not place any object in the vicinity of the air inlet. The air intake may not be blocked. The wall must be strong enough to bear the weight of the unit. The wall construction may not cause any increase in noise and vibrations.

Front panel

Connecting clamp (inside)

Housing

Installation diagram

Indoor unit

Not higher than 5 m

Outdoor unit

Location for the installation of the outdoor unit

In an accessible, well ventilated location. Do not mount at potentially hazardous locations, e.g. where there is a danger of a gas leak. Maintain the required distance from the wall. Do not expose the outdoor unit to greasy dirt or salty sea air. Do not mount in the vicinity of gas pipes. Do not mount on the street side due to the risk of water splashing onto the unit. Mount on a fixed foundation in order to prevent excessive noise. The air outlet must not be obstructed.

10 m (S95) or a

max. of 15 m

Max. length of

Outdoor unit

Not higher than 5 m

Indoor unit

(S125, S185, S245).

Max. length of 10 m

(S95) or a max. of

15 m (S125, S185,

S245).

INSTALLATION OF THE INDOOR UNIT

1. Installing the mounting plate

- Fit the mounting plate at the location where the indoor unit will be hung. Take a

ccount of the direction of the pipes.

- Place the mounting plate horizontally with the aid of a level indicator or plumb line.

- Drill holes with a depth of 32 mm in order to mount the plate.

- Insert the plastic plugs into the holes and screw the plate into position with selftapping screws.

- Check that the mounting plate is firmly in position and drill the hole for the pipes.

Note: the shape of the mounting plate may differ per model. However, the installation method is the same.

2. Drilling a hole for wires/pipes

- Determine the position of the lead-through hole for the wires/pipes on the basis of the drilling hole in the mounting plate.

- Drill the hole in the wall. The hole must slope a little to the outside.

- Place a pipe sleeve in the hole in order to protect the wall.

3. Indoor unit wire/pipe installation

- Insert he wires/pipes (gas and liquid pipes) through the hole from the outside, or from the inside if you have installed the indoor unit first.

- Create a recess that corresponds with the direction of the pipes.

Note: create recess 1, 2 or 4, depending on the position you have chosen for the hole in the indoor unit.

- Fit the drainage hose after connecting the wires/pipes. Now connect the power cables. Finish by insulating the pipes, cables and drainage hose.

Insulation of the pipe connections: them in vinyl tape.

Insulate the connection pieces with insulating material and then wrap

ipe insulation: a. Place the drainage hose under the pipe. b. Use insulating material exceeding 6 mm in

Power cable

Large pipe

Insulating pipe

thickness.

mall

- The drainage hose must slope downwards

lightly in order to allow moisture to drain

Power cable 1

heat pump)

(

S pipe

away easily. Ensure that the drainage hose is not twisted and does not protrude. The end

iring of defrosting

W regulator (heat pump)

Tape

rainage hose

may not hang in the water. If the drainage hose is extended with a hose, the section running alongside the indoor unit must be insulated.

- If the wire/pipes are on the right hand side, the wires/pipes, power cable and drainage hose must be

insulated and fastened to the back of the indoor unit with a pipe clamp.

A. Fasten the pipe clamp to the groove.

Mounting plate

Pipe clamp

Mounting plate

Pipe clamp

B. Press the clamp to attach it to the mounting plate.

Connecting the pipes

a. Connect the indoor unit pipes with two nut spanners. Select the

correct tightening moment in order to prevent the pipes, connecting pieces and nuts from being deformed or damaged.

b. First tighten by hand, and then with nut spanners.

ightening

Model

S95/S125/S185

S245

S95

S125/S185

S245

Pipe dimensions

moment

Push through here

Mounting plate

Nut

size

Hook here

. Connecting the cable

- Indoor unit

Connect the power cable to the indoor unit by connecting the cables to the units to the clamps on the terminal board in the correct sequence. The colours of the wires and the r

eference on the clamps must correspond.

Note: In some models, the cover must be removed in order to connect the wiring.

- Outdoor unit

1. Remove the access cover of the unit by loosening the screw. Connect the wires to the clamps on the terminal board in the following manner:

2. Connect the power cable to the terminal board.

3. Replace the cover and tighten the screw.

4. Place an approved circuit breaker between the power source and the unit for model S245. Install a suitable main switch.

Front panel

Indoor unit

Outdoor unit

Terminal board (inside)

Base plate

Housing

Access cover for terminal board (inside)

The illustrations are based on standard models. The air conditioner you have purchased may be a different model.

Warning:

1. Always connect the air conditioner to a separate power circuit. Refer to the diagram on the inside of the access cover for the connection of the wires.

2. Check that the cable thickness conforms to regulations (see table below).

3. Check that all wiring is securely connected.

4. Install an earth leak switch.

Note: All cables used must be approved in accordance with local regulations.

Cable specifications

Power cable Power cable connection

Type Cross-section Type Cross-section Type Cross-section

S95 S125 S185

S245

Power cable connection 1 (heat pump)

OUTDOOR UNIT INSTALLATION

1. Fit the drainage outlet and drainage hose (only for models with a heat pump). Condensation will drip off the outdoor unit when the indoor unit i

s operating in Heating mode. Fit a drainage outlet and a drainage hose in order to drain the water effectively. Fit the drainage outlet and rubber washer to the base plate of the outdoor unit (see fig.).

2. Installing and fitting the outdoor unit Bolt the unit to a level and solid base. Ensure that the unit is mounted securely in order to prevent problems caused by strong wind and vibrations.

3. Connecting the outdoor unit pipes Remove the covers of the two-way and three-way valve. Close the pipes separately with the appropriate tightening moment.

4. Outdoor unit cable connection (see previous page)

Purging the pipe system

Air and moisture that remain in the pipe system after installation can damage the compressor. After the indoor and outdoor units have been connected, air and moisture must be removed with the aid of a vacuum pump (see below).

Vacuum pump

Three-way valve diagram

. Unscrew the two-way and three-way valve and remove the covers.

2. Unscrew the supply pipe and remove the cover.

3. Connect the flexible hose of the vacuum pump to the supply pipe.

4. Allow the vacuum pump to operate for 10-15 minutes until a pressure of 10 mmHg absolute is achieved.

. Close the low-pressure button on the vacuum pump while the pump is still operating. Now switch the

pump off.

6. Open the two-way valve (1/4 turn), and close it again after 10 seconds. Check all connections with liquid soap or an electronic leak detector.

7. Turn the two-way and three-way valves to their operating positions. Disconnect the hose from the vacuum pump.

8. Replace and tighten all covers.

Note

- Read these instructions for use before commencing installation.

- Make sure that no air remains in the cooling system and that no refrigerant is leaking.

- Testing: switch the air conditioner on after installation and take notes on the operation.

- Fuse of the indoor unit controller for types S95 and S125: 50T, permitted value 3.15 A,T, 250V. For types S185 and S245: 3.15A, T, 250V.

- The fuse for the unit as a whole must be suitable for maximum power.

- The plug must be easily accessible in order to be able to switch the unit off in case of emergency. If there is no easy access, a bipolar main switch must be installed at an easily accessible location.

E INSTRUCTIONS FOR USE

Operation and display

POWER INDICATOR Lights up when power supply is connected.

SLEEP MODE INDICATOR Lights up when this function is

ctivated.

RECEIVER Receives the signal from the remote control.

TIME INDICATOR Lights up during preset time.

OPERATING INDICATOR Lit when the unit is in operation.

EMERGENCY BUTTON To operate the unit if the remote control is not operational.

Adjustment of automatic restart

The machine has been programmed by the manufacturer to restart automatically.

Following a power cut, the machine will resume operation in the last selected function.

The shapes and positions of the switches and indicators may differ for each model. However

, the functions are identical.

Remote control

The remote control transmits signals to the system.

To activate or deactivate the sleep mode.

To select the TIMER function.

To select the operating mode: Feel, Cooling,

Dry, Fan and Heating.

DOWN button (TOO W

To lower the preset room temperature and

SLEEP button

TIMER button

MODE button

ARM button)

reduce time periods.

UP button (TOO COLD button) To raise your preset room temperature and extend time periods.

FAN SPEED operation button

or the selection of the ventilator speed in the

F indoor unit: automatic, high, medium and low.

orizontal plate button

H To adjust the direction of the airstream.

ON/OFF button For activation and deactivation.

Note: Each mode and the relevant functions will be specified hereafter.

Placing the batteries

Remove the battery cover in the direction of the arrow. Place the new batteries as indicated (ensure that the positive (+) and negative poles (-) are in the correct positions. Slide the battery cover back into place.

Note: Use 2 LR03 AAA (1.5 Volt) batteries. Do not use rechargeable batteries. Replace the batteries with new batteries of the same type (see above) when the display starts to fade.

Storage of the remote control and tips for use

The remote control can be placed in a wall-mounted holder.

Note: The remote control holder is optional.

Using the remote control

Point the r

emote control at the receiver on the indoor unit of the

Receiver

air conditioner. The air conditioner can be operated in this manner up to a distance of 7 metres.

OPERATING INSTRUCTIONS

Less than 20 °C

23 °C

FEEL mode operating procedure

The operating mode is selected automatically (HEATING, DRY, FAN, COOLING), depending on the room temperature at the t

ime the selection takes place.

With the remote control pointed at the air conditioner.

1. Activation Press the ON/OFF/RUN button. The RUN indicator on the indoor unit will light up when the machine receives a signal.

When the unit is not in the FEEL mode.

2. Selecting the FEEL mode Press the MODE selector button. Adjust the MODE to the FEEL setting.

The operating mode and temperature are determined by the indoor temperature.

Indoor temperature Operating mode Desired temperature

Heating for ‘heat pump’ type

Ventilator for ‘cooling only’ type

20 – 26 °C DRY 18 °C

More than 26 °C COOLING 23 °C

3. Temperature adjustment Press the When the

g button or the h button.

g button is pressed, the value of the preset temperature increases by 1°C.

The indicator will not change after the temperature has been increased by 2°C. When the

h button is pressed, the value of the preset temperature is lowered by 1°C.

The indicator will not change after the temperature has been lowered by 2°C.

Note: It may occur that no air is expelled from the unit while it is in operation. The unit will not always start operating immediately after the mode has been changed.

TIMER mode

If you program the timer with the TIMER button upon leaving, it will be pleasantly warm when you return home. Y

ou can deactivate the timer at night if you wish.

ADJUSTING THE TIMER

To activate the air conditioner at the desired time, follow the procedure specified below (the remote control and air conditioner are switched off):

1. Press the Timer button.

. Select the desired mode by pressing the Mode button.

3. Select the desired temperature by pressing the possible when the ‘cool’ or ‘heat’ mode is selected).

4. Select the ventilator speed (low, medium or high) or automatic mode (only possible when the Feel, Cool or Heat mode is selected) by pressing the Fan button. The ventilator always operates in the Auto mode when the Dry mode is selected.

5. Select Swing or no Swing by pressing the Swing button.

6. Press the Timer button (‘h’ flashes).

7. Use the activate (between 0 and 10 hours can be set at every half hour – between 10 and 24 hours can be set at every hour).

8. Press the Timer button (‘h’ stops flashing) and the preset time appears in the display.

9. Press the Timer button again to delete the selected data from the memory.

gh button to select the time at which the air conditioner must

gh button (only

Note: If no buttons are pressed during the programming of the timer function, the remote control will switch off automatically after 10 seconds.

To switch the air conditioner off at the desired time, follow the procedure specified below (the remote control and air conditioner are switched off):

1. Press the Timer button.

2. Use the hours can be set at every half hour – between 10 and 24 hours can be set at every hour).

3. Press the Timer button (‘h’ stops flashing), and the preset time will appear in the display.

4. Press the Timer button again to delete the selected data from the memory.

Note: If no buttons are pressed during the programming of the timer function, the remote control will switch off automatically after 10 seconds.

Note: if ‘h’ is flashing and you press the ON/OFF/RUN button once, the preset temperature will appear in the display. You can now adjust the temperature with the display the time, which can now also be adjusted*. If the Timer button is pressed again, the data is stored and the remaining time (that the air conditioner will be in operation) will appear in the display.

Pressing the ON/OFF/RUN button instead of the Timer button deactivates the remote control.

gh button to select the time at which the air conditioner must deactivate (between 0 and 10

gh button. Press the Timer button again to

Note

Press the Timer function to check the settings in the display

Check that the TIMER INDICA

TOR on the indoor unit lights up after the timer has been set.

F MAINTENANCE

Cleaning the front panel

1 Switch the machine off and remove the plug from the socket. 2 Hold the front panel at position “a” and pull it towards you. 3

Clean with a soft dry cloth. Use lukewarm water (max. 30˚ C) to remove stubborn dirt.

4 Never use volatile substances, such as benzene, or abrasives to

remove dirt.

5 Never spray water on the indoor unit.

Dangerous! Electric shock!

6 Replace the front panel and close it by pushing position “b” down.

Cleaning the air filter

The air filter must be cleaned regularly. Follow this procedure:

1. Switch the machine off completely.

- Open the front panel.

- Carefully pull the filter handle towards you.

- Grip the handle and slide the filter out.

2. Clean and replace the air filter. To remove stubborn dirt, clean the filter in lukewarm water with detergent. After cleaning, allow the filter to dry completely out of direct sunlight.

3. Close the front panel. If the air conditioner is operating in an extremely dusty environment, it must be cleaned every two weeks.

G SAFETY

Operating status

The safety components can detect faults and deactivate the unit in the following cases:

HEATING

The outside temperature is above 24°C The outside temperature is under -7°C The room temperature is above 27°C

COOLING

The outside temperature is above 43°C The r

oom temperature is under 21°C

DRY

The r

oom temperature is under 18°C

Warning

If the air conditioner is operating in the COOLING or DRY mode while relative humidity is over

Noise

- Install the air conditioner on a solid base in order to prevent excessive noise.

- Install the outdoor unit in such a way that the expelled air does not cause a nuisance for neighbours.

- Do not place obstacles in the path of the air expelled from the outdoor unit, this increases noise.

Safety features

1 The safety feature deactivates the unit in the following cases:

2. Press the ON/OFF button to restart after the unit has deactivated due to the operation of the safety

80%, moisture may drip out of the air outlet of the indoor unit (due to a window or door being open, for instance).

- When the function is stopped or changed while the unit is operating. Wait 3 minutes before

switching the air conditioner on again.

- After the plug has been inserted in the socket and the unit has been immediately switched on. The

unit will activate after approximately 20 seconds.

feature. The Timer must then be reset.

Checks

The following must be checked after the air conditioner has been in use for an extended period of time:

- Overheating of the power cable and the plug. Can you smell burning?

- Is there more noise or vibration than normal?

- Does the indoor unit leak water?

- Is the metal housing live?

Switch the air conditioner off in all the above cases! We recommend periodic inspection by a registered installer (at least once every five years).

Feature of the HEATING mode

For heating

When the HEATING function is activated, the airstream will only start to flow from the indoor unit after 2 – 5 minutes.

After Heating

When the Heating function is deactivated, the ventilator of the indoor unit will continue operating for another 2 – 5 minutes.

Defr

osting

During HEATING, the machine will defrost automatically in order to ensure optimum operating efficiency. This procedure usually takes 2-10 minutes. The ventilator function stops during defrosting. The HEATING function r

estarts automatically after defrosting.

H PROBLEM SOLVING

Problem Cause / Solution

The plug is not inserted firmly in the socket.

The batteries in the remote control are empty.

The safety feature has been activated or the fuse has burnt out.

re the air inlets or outlets blocked?

Is the temperature set correctly?

Is the air filter dirty?

No effective operation.

Faults (due to static electricity discharges or disruptions in the power supply) will prevent the machine from operating correctly. If this is the case, pull the plug out of the socket, and then reinsert it after 2-3 seconds.

Does not start immediately. Changing the mode during operation: 3 minute delay.

Unusual odour.

Odour may be caused by another source – furniture, cigarettes, etc. The unit expels air that it has sucked in.

Caused by the refrigerant in the air conditioner: this does not indicate a fault.

The sound of defrosting in the heating mode.

A creaking sound.

The sound may be caused by the expansion/shrinkage of the front panel as a consequence of temperature fluctuations.

Mist/moisture is expelled from the air outlet.

Condensation/mist is created when the air temperature in the room drops significantly due to the fact that cold air is expelled in the COOLING or DRY mode.

The red compressor indicator flashes constantly and the ventilator in the indoor unit ceases to operate.

The unit will switch from the heating mode to the defrosting mode. The indicator light will go out within 10 minutes and the unit will return to the heating mode.

No cooled or heated air. The sound of running water.

The unit does not operate.

The following problems do not always indicate a fault. Please check them before contacting the service department:

I GUARANTEE CONDITIONS

There is a 24-month guarantee on the air conditioner from the purchase date. Within this period, all material and manufacturing defects will be repaired free of charge. The following rules will apply:

•

We expressly reject all further claims to damage compensation, including claims relating to secondary damage.

• Repairing or replacing components within the guarantee period will not extend the guarantee.

• The guarantee is invalidated if any modifications have been made to the machine, non original parts have been fitted or repairs have been carried out by third parties.

• Components subject to normal wear, such as the filter, are not covered by the guarantee.

• The guarantee is valid exclusively when you present the original, dated and unaltered purchase invoice.

• The guarantee does not cover damage caused by actions that deviate from the instructions for use or neglect.

• Shipment costs and the risks associated with shipping the air conditioner or parts thereof will always be borne by the buyer.

To prevent unnecessary expense, we recommend that you first always consult the instructions for use carefully. If this does not provide a solution, ask your dealer to repair the air conditioner.

Egregio Signore, Gentile Signora,

Ci congratuliamo con per l’acquisto del condizionatore d’aria. Lei ha acquistato un

prodotto di qualità, che Le offrirà molti anni di comfort, a condizione che venga usato in

modo responsabile. Per una durata ottimale del condizionatore d’aria La invitiamo a

leggere le istruzioni d’uso. A nome del fabbricante Le offriamo 24 mesi di garanzia per

tutti i danni imputabili alla produzione o al materiale.

Le auguriamo molta freschezza e comfort.

Cordiali saluti,

PVG International b.v.

Reparto Assistenza Clienti

1. LEGGERE DAPPRIMA LE ISTRUZIONI D’USO

2. IN CASO DI DUBBIO, RIVOLGERSI AL RIVENDITORE

CONTENUTO

A Specifiche pagina 24

B Componenti pagina 25

C Operazioni preliminari pagina 26

D Istruzioni per l’installazione pagina 27

E Istruzioni d’uso pagina 34

F Manutenzione pagina 38

G Sicurezza pagina 38

H Risoluzione dei problemi pagina 40

I Condizioni della garanzia pagina 41

A SPECIFICHE

m3/

480 550 730 1000

90 110 150 200

OP *

Modello

E Class

ER *

COP Class

I valori riportati sono indicativi, dati soggetti a modifiche

S95 S125 S185 S245

a. di raffreddamento* kW 2,7 3,5 5,3 7,0

DDDD

2,8 2,8 2,8 2,9

apacità di riscaldamento kW 2,8 3,8 5,7 7,6

,2 3,2 3,4 3,5

eumidificazione (max) ** L/24 h 19 24 36 48

Assorbimento energia in raffreddamento kW 0,88 1,17 1,9 2,6

Assorbimento energia in riscaldamento kW 0,88 1,17 1,9 2,6

Alimentazione Volt/Hz/Pf 220-240/50/1 220-240/50/1 220-240/50/1 220-240/50/1

orrente (nom) A 3,6 5,1 8,7 12,8

Flusso aria (max)

Ideale per ambienti fino a

Dimensioni unità interna (PxLxH) mm 718x180x240 770x180x240 1033x202x313 1033x202x313

Dimensioni unità esterna (PxLxH) mm 669x296x506 769x328x552 829x328x552 929x372x652

Peso unità interna kg 7 7 14 14

Peso unità esterna kg 24 32 42 56

Refrigerante gr R407C/540 R407C/900 R407C/1680 R407C/2300

Livello di rumore unità interna (max) dB(A) 36 38 43 47

Livello di rumore unità esterna (max) dB(A) 50 50 60 54

Temperatura di esercizio ºC 10-40 10-40 10-40 10-40

Protezione unità interna IP IP X0 IP X0 IP X0 IP X0

Protezione unità esterna IP IP X4 IP X4 IP X4 IP X4

DDD

* Conforme a EN 14511 ** Tasso di humidità relativa pari al 80% ad una temperatura di 32°C

Gli apparecchi elettrici difettosi e le batterie usate non devono essere smaltiti come rifiuti domestici. Se possibile utilizzarli per il riciclaggio. Eventualmente informarsi presso il proprio comune o il rivenditore locale sulle possibilità di riciclaggio o di smaltimento ecologico.

B IDENTIFICAZIONE DEI COMPONENTI

UNITÀ INTERNA

Presa d’aria

Quadro frontale

Pulsante di emergenza

Display

Uscita dell’aria

Regolazione ver-

ticale delle lame

Regolazione oriz-

zontale delle lame

Filtro anti-par-

ticelle di carbon

attivo (optional)

Filtro di sicurez-

za per la tutela della

salute (optional)

UNITÀ ESTERNA

Le figure riportate nel presente manuale si riferiscono a un modello standard. Il vostr

o condizionatore può essere un modello diverso.

Filtro dell’aria

Telecomando

Presa d’aria

Tubo flessibile di

scarico*

Tubi e cavo di

alimentazione

Uscita dell’aria

* NB: la funzione di scarico dell’aria di condensa è attiva in modalità CONDIZIONAMENTO o DEUMIDIFICAZIONE

C PREPARATIVI PRIMA DELL’USO

Prima di utilizzare il condizionatore d’aria, verificare e impostare i seguenti parametri.

Impostazione del telecomando

l telecomando NON è impostato direttamente in fabbrica per utilizzare l’apparecchio come generatore di aria fredda ad uso condizionamento (condizionatore) o di aria calda ad uso riscaldamento (pompa di calore). Ad ogni sostituzione delle batterie del telecomando, sul display frontale lampeggerà l’apposita freccia luminosa “Heat” (“caldo”) o “Cool” (“freddo”). È possibile impostare il telecomando in funzione del tipo di apparecchio acquistato nel modo seguente: premere un pulsante qualsiasi quando la freccia luminosa posta sul display frontale lampeggia in corrispondenza della dicitura “Heat” (“caldo”), viene selezionata la funzione “pompa di calore”. premere un pulsante qualsiasi quando la freccia luminosa posta sul display frontale lampeggia in corrispondenza della dicitura“Cool” (“freddo”), viene selezionata la funzione “condizionamento”. Se non viene premuto alcun pulsante entro 10 secondi, il telecomando viene impostato automaticamente per la funzione “pompa di calore”. Gli apparecchi S95, S125, S185 e S245 sono dotati di una pompa di calore.

Impostando il telecomando per utilizzare l’apparecchio solo a fini di condizionamento, NON è possibile impostare la funzione di riscaldamento con il telecomando.

Precauzioni di sicurezza

• Utilizzare il corretto valore di tensione in funzione di quanto indicato sull’apposita targhetta per

evitare gravi danni all’apparecchio o rischi di incendio.

• Tenere costantemente pulito l’interruttore o la spina di alimentazione. Collegare l’interruttore/spina in

modo saldo e preciso al cavo di alimentazione. Un contatto insufficiente potrebbe essere causa di elettroshock o incendio.

• Non utilizzare l’interruttore o togliere la spina per spegnere l’apparecchio quando è in funzione. Esiste

il rischio di propagazione di scintille che potrebbero causare un incendio.

• Non torcere, tirare o schiacciare il cavo di alimentazione per evitare rischi di elettroshock o incendio.

• Non inserire oggetti estranei quali bastoni o simili nell’apparecchio. A causa dell’elevata velocità di

rotazione della ventola possono verificarsi incidenti.

• Evitare un’esposizione diretta prolungata al flusso di aria fredda in provenienza dall’apparecchio. Si

consiglia di optare per un flusso diffuso.

• In caso di malfunzionamento, spegnere l’apparecchio con il telecomando prima di togliere la spina

dalla presa di alimentazione

• Non procedere direttamente alla riparazione dell’apparecchio. Riparazioni non eseguite da personale

specializzato possono provocare elettroshock ecc….

• Evitare di dirigere il flusso d’aria verso cucine a gas e stufe.

• Non toccare i pulsanti con le mani bagnate.

•

Non inserire alcun oggetto nell’unità esterna.

• La messa a terra conforme alle leggi o norme locali da parte di un tecnico autorizzato rientra nelle

responsabilità dell’utente.

D ISTRUZIONI PER L’INSTALLAZIONE

Schema di installazione

La distanza dal muro

deve essere superiore

a 50 mm.

La distanza dal soffitto deve essere superiore a 50 mm.

a distanza dal muro deve

L essere superiore a 50 mm.

La distanza tra il bocchettone di uscita dell’aria e il muro deve essere superiore a 250 mm.

La distanza tra il bocchettone di uscita dell’aria e il muro deve essere superiore a 500 mm.

- La figura sovrastante è una presentazione semplificata dell’apparecchio, che potrebbe differire rispetto al prodotto da voi acquistato.

- L’installazione deve essere eseguita esclusivamente da personale autorizzato nel rispetto delle normative nazionali.

La distanza tra il bocchettone di uscita dell’aria e il muro deve

e superior

esser

minimo 250 mm.

e a 250 mm.

Collegamento del cavo di alimentazione

Connessione tra l’unità interna e l’unità esterna

1. Rimuovere il rivestimento in plastica dell’unità interna.

2. Per il collegamento far riferimento al diagramma dei cablaggi (allegato all’unità interna).

. Ricollocare il rivestimento in plastica. Verificare che il

lato “B” sia all’esterno.

Scegliere la migliore collocazione per l’apparecchio.

Non collocare alcun ostacolo nei pressi del bocchettone di uscita dell’aria in modo tale che l’aria sia libera di circolare in ogni punto della stanza. I tubi e il foro da praticare nel muro devono essere in posizioni accessibili. Predisporre uno spazio adeguato dall’apparecchio al soffitto e al muro (cfr. capitolo D). I filtri dell’aria devono essere facilmente estraibili. Tenere l’apparecchio e il telecomando a una distanza minima di 1 m da televisore, radio, ecc. Le lampade fluorescenti possono causare interferenze. Tenerle ad adeguata distanza. Non mettere nulla vicino al bocchettone di uscita dell’aria, in modo tale da garantire la massima circolazione dell’aria. Il muro deve essere sufficientemente solido per sostenere il peso del condizionatore e non contribuire ad aumentare il rumore e le vibrazioni prodotti durante il funzionamento.

Quadro frontale

Morsetto di collegamento (interno)

Cassa

Schema di installazione

Unità interna

Altezza max. pari a 5 m.

Unità esterna

Collocazione dell’unità esterna

Collocare l’unità esterna in un punto accessibile e ben ventilato; non collocarla, per esempio, in un punto che presenti pericolo di perdite di gas. Mantenere la corretta distanza dal muro. L’unità esterna non deve essere esposta ad aria di mare sporca, grassa o salata o collocata nei pressi di tubi di scarico. Non installare lungo una strada per evitare spruzzi di acqua. Predisporre una base fissa per evitare l’aumento della produzione di rumore. Verificare che l’aria possa circolare liberamente.

dei tubi: 10 metri

Lunghezza max.

Unità esterna

Altezza max. pari a 5 m.

Unità interna

(S95) o 15 metri

(S125, S185, S245)

tubi: 10 metri (S95)

o 15 metri (S125,

Lunghezza max. dei

S185, S245)

Installazione dell’unità interna

1. Installazione del piano di supporto

- scegliere il punto dove collocare il piano di supporto dell’unità esterna tenendo conto d

ella direzione dei tubi;

- disporre il piano di supporto orizzontalmente con l’ausilio di una riga orizzontale o di una bolla;

- praticare fori di 32 mm di profondità nel muro per fissare il piano di supporto;

- inserire i tasselli in plastica nei fori e fissare il piano di supporto con viti a filetto tagliente;

- verificare che il piano di supporto sia ben fissato. Praticare poi un foro per i tubi.

NB: la forma del piano di supporto varia da modello a modello, ma il metodo di installazione è identico.

2. Praticare un foro per i tubi

- Determinare la posizione del foro per i tubi nel muro in base al foro nel piano di supporto;

- praticare un foro nel muro. Il foro dovrebbe deviare leggermente verso l’esterno;

- inserire un manicotto nel foro per proteggere il muro.

3. Installazione tubi unità interna

- Inserire i tubi (del liquido e del gas) e i cavi nel buco praticato nel muro partendo dall’esterno verso l’interno oppure dall’interno verso l’esterno qualora sia già stata installata l’unità interna;

- tagliare il segmento in plastica in funzione della direzione dei tubi.

NB: tagliare il segmento in plastica 1, 2 o 4, in funzione della posizione scelta per il foro nell’unità interna.

- dopo aver installato i tubi, installare il tubo flessibile di scarico. Dopodiché collegare i cavi di alimentazione. Infine isolare i tubi, i cavi e il tubo flessibile di scarico.

Isolamento ter applicar

mico giunti tubi. Avvolgere i giunti dei tubi con un materiale isolato termicamente e poi

e del nastro in vinile.

Isolamento termico tubi

a. collocare il tubo flessibile di scarico sotto i

tubi; utilizzare materiale di isolamento con

spessore maggiore di 6 mm;

il tubo flessibile di scarico deve puntare verso il basso per agevolare lo scarico. Verificare che il tubo flessibile di scarico non sia piegato, avvolto su se stesso o sporgente; non immergerne l’estremità in

Tubo di grandi dimensioni

Cavo di alimentazione

Cavo di alimen-

azione 1 (per

ompa di calore)

avo per regolazione dello

C sbrinamento (per pompa di calore)

Tubo di isolamento termico

ubo di piccole

T dimensioni

Tubo flessibile di scarico

astro

acqua. Se il tubo flessibile di scarico è collegato a una prolunga, la parte che passa lungo l’unità interna deve essere isolata.

- Quando i tubi sono diretti verso destra, i tubi, il cavo di alimentazione e il tubo flessibile di scarico devono essere isolati e montati sul retro dell’unità interna con un apposito dispositivo di fissaggio.

Inserire qui

Piano di supporto

Dispositivo di fissaggio del tubo

Piano di supporto

Dispositivo di fissaggio del tubo

Piano di supporto

A. Inserire il dispositivo di fissaggio del tubo nell’alloggiamento B. Premere per agganciare il dispositivo di fissaggio del tubo al piano di supporto

Vollegamento dei tubi

a. Collegare i tubi dell’unità interna con due chiavi. Prestare parti-

e attenzione alla coppia di ser

colar tale da evitar

e che i tubi, i giunti e i dadi si defor

raggio consentita, in modo

mino o dan

neggino.

b. Stringergli prima con le dita, poi utilizzare le chiavi.

Modello

S95/S125/S185

S245

S95

S125/S185

S245

Dimensione del tubo

Serraggio

Ampiezza

dei dadi

Fissare qui

+ 72 hidden pages