Zephyr EOT-E42ASX User Manual

Loading...

www.zephyronline.com

Guía de instalación, uso y mantenimiento

Guide d’utilisation, d’entretien et d’installation

Use, Care, and Installation Guide

Optica Island

EOT-E42ASX

EOT-E48ASX

Model number:

Numéro de modèle: ____________________________________

Número de modelo:

Serial number:

Numéro de série: _____________________________________

Número de serie:

Date of Purchase:

Date d’achat: _____________________________________

Fecha de compra:

Sales Dealer:

Détaillant: _____________________________________

Distribuidorr:

LI2Q9A 1005 rev:1

READ AND SAVE THESE INSTRUCTIONS

LISEZ CES INSTRUCTIONS ET CONSERVEZ-LES LEAY GUARDE ESTAS INSTRUCCIONES

E page

2

F page

23

S page

45

APPROVED FOR RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference.

Safety Warning: Turn off power circuit at service panel and lock out panel, before wiring this appliance. Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit

2

Important safety Notice .....................................................................

4

Electrical & Installation requirements ..............................................

5

Electrical requirements ..............................................................

5

Before installing the hood ..........................................................

5

List of Materials .................................................................................

6

Parts supplied: ...........................................................................

6

Parts not supplied ......................................................................

6

Dimensions and clearances .............................................................

7

Installation Instructions ....................................................................

8

Venting methods ........................................................................

8

Preparation ................................................................................

8

Installation - Ductwork Calculation Sheet ......................................

9

Installation .......................................................................................

10

Electrical connection................................................................

12

Description of the hood & Controls ...............................................

16

Controls ...................................................................................

16

Description of control panel: ....................................................

16

Maintenance.....................................................................................

17

Cleaning ..................................................................................

17

Grease filter .............................................................................

17

Replacing the light bulb: ..........................................................

17

Trouble Shooting .....................................................................

18

Warranty ...........................................................................................

19

List of Parts and Accessories .........................................................

20

www.zephyronline.com

Table of Contents

3

READ AND SAVE THESE INSTRUCTIONS

Important safety Notice

CAUTION:

FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPORS.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A.Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.

B.Before servicing or cleaning the unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

C.Installation Work and Electrical Wiring Must Be Done By Qualified Person(s) In Accordance With All Applicable Codes & Standards, Including Fire-rated Construction.

D.Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturers guideline and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

E.When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

F.Ducted systems must always be vented to the outdoors.

CAUTION:

To reduce risk of fire and to properly exhaust air, be sure to duct air outside - do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces, or garages.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT WORK.

Install this hood in accordance with all requirements specified.

WARNING

To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Hood With Any External Solid State Speed Control Device.

WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE.

a)Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

b)Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe’).

c)Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

d)Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:

a)SMOTHER FLAMES with a close-fitting lid, cookie sheet, or other metal tray, then turn off the gas burner or the electric element. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

b)NEVER PICK UP A FLAMING PAN - you may be burned.

c)DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result.

d)Use an extinguisher ONLY if:

1)You know you have a class ABC extinguisher, and you already know how to operate it.

2)The fire is small and contained in the area where it started.

3)The fire department is being called.

4)You can fight the fire with your back to an exit.

OPERATION

a. Always leave safety grills and filters in place. Without these components, operating blowers could catch onto hair, fingers and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance.

* NOTE: Please check our website for revisions before doing any custom work.

4

www.zephyronline.com

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

To contact a qualified electrical installer.

To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

— latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure range hood is properly grounded. Do not have a fuse in the neutral or ground circuit.

IMPORTANT:

Save Installation Instructions for electrical inspector’s use. The range hood must be connected with copper wire only.

The range hood should be connected directly to the fused disconnect (or circuit breaker) box through metal electrical conduit.

Wire sizes must conform to the requirements of the National Electrical Code ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code Part 1 and C22.2 No. 0-M91 - latest edition** and all local codes and ordinances.

A U.L.- or C.S.A.-listed conduit connector must be provided at each end of the power supply conduit (at the range hood and at the junction box).

Copies of the standards listed may be obtained from:

* National Fire Protection Association Batterymarch Park Quincy, Massachusetts 02269 ** CSA International 8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575

BEFORE INSTALLING THE HOOD

1.For the most efficient air flow exhaust, use a straight run or as few elbows as possible. CAUTION: Vent unit to outside of building, only.

2.Almost two people are necessary for installation.

3.The hood is fitted with Screws and Drywall Anchors suitable for most surfaces, consult a Qualified Installer, check if they perfectly fit with your cabinet/wall.

4.Do not use flex ducting.

5.COLD WEATHER installations should have an additional backdraft damper installed to minimize backward cold air flow and a nonmetallic thermal break to minimize conduction of outside temperatures as part of the ductwork. The damper should be on the cold air side of the thermal break.

The break should be as close as possible to where the ducting enters the heated portion of the house.

6.Make up air: Local building codes may require the use of Make-Up Air Systems when using Ducted Ventilation Systems greater than specified CFM of air movement.

The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area.

Electrical & Installation requirements

5

List of Materials

PARTS SUPPLIED:

Blower unit housing

Hood canopy

Metal filter x 1

Halogen light bulb x 4

Upper and lower Duct covers x 4

Chimney structure

Hardware Packet: Allen spanner x 1 Template

Use, Care and Installation guide Nuts x 12

7x45 screws x 6

4 x 6 screws x 12 (to assemble duct covers)

3,5x6,5 screws x 13 (11 to assemble Hood canopy to Chimney structure + 2 to fix duct covers to chimney structure). 3,5 x 9,5 screws x 24 (to fix one to another brackets and blower unit)

PARTS NOT SUPPLIED

Duct, conduit and all tools required for installation.

Ductless recirculating kit

to be used only in the Ductless (recirculating) version

includes: charcoal filter, charcoal filter support and fixing bracket, deflector

Internal blower

To be used only in case of Internal blower installation.

In-line blower

To be used only in case of in-line blower installation

Noise reduction sponge

Note: may be already included on internal/in-line blower package.

CAUTION

To reduce the risk of fire and electric shock, install this rangehood only with integral blowers mod. EBI-600 rated 120V 60Hz 450W or with remote blowers mod. EBN-1100 rated 120V 60Hz 900W, manufactured by Elica.

6

www.zephyronline.com

 

*min. 31" 10/16

 

*max. 49"

 

min. 30" 8/16

26" 4/16

max. 43" 14/16

1"

27" 8/16

42" - 48"

14"

12" 3/16

Dimensions and clearances

* Ductless (recirculating) version ONLY Note: if necessary order the proper duct cover extension kit.

7

+ 15 hidden pages