Zenoah CHT2301 User Manual

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

WARNING

OWNER/OPERATOR MANUAL

HEDGE-TRIMMERS

HT2301

CHT2301



Thank you for purchasing a RedMax product. Before using our hedge-trimmers, please read this manual carefully to understand the proper use of your unit.

T1146-93110 (202)

APPLICABLE SERIAL NUMBERS : 100101 and up

SAFETY FIRST

Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.

■ WARNINGS IN THE MANUAL

This mark indicates instructions which must be followed in order to prevent accidents which could lead to serious bodily injury or death.

This mark indicates instructions which must be followed, or it leads to mechanical failure, breakdown, or damage.

This mark indicates hints or directions useful in the use of the product.

NOTE

CONTENTS

1. Parts location …………………………………4

2. Specifications …………………………………5

3. Warning labels on the machine ……………6

4. Symbols on the machine ……………………7

5. For safe operation ……………………………8

6. Fuel……………………………………………14

7. Operation ……………………………………16

8. Maintenance …………………………………20

9. Storage ………………………………………24

10. Troubleshooting guide………………………24

11. Parts list………………………………………25

WARNING

IMPORTANT

1. Parts location

❲4❳

1. Right handle

2. Fuel tank

3. Starter

4. Left handle

5. Throttle lever

6. Ignition switch

7. Throttle Cable

8. Muffler

9. Blade

10. Front handle

11. Rear handle

12. Air filter

2. Specifications

Engine Type······················································································ Air-cooled 2-stroke gasoline

Model········································································································ Zenoah G23LH Displacement ······················································································· 1.4cu-in (22.5cm3) Max. output ··································································· 0.7Hp (0.5kW)at 6500/min-1(rpm) Idle speed························································································3200 ± 200/min-1(rpm) Fuel ······················································································ Mixture (Gasoline 50 : Oil 1) Carburetor ··················································································· Walbro Diaphragm type Spark plug ···························································································· Champion RCJ6Y

Fuel tank capacity································································································ 20.3 fl.oz (0.6 )

■ HT2301

Type····································································· Reciprocating single-sided dual blades Blade size····························································································· 750 (mm) / 30 (in) Blade pitch··························································································· 41 (mm) / 1.62 (in) Dry weight··························································································· 5.4 (kg) / 11.4 (lbs) Transmission ····································································· Centrifugal clutch, Cam-crank Reduction ratio········································································································· 4.417

■ CHT2301

Type ····································································· Reciprocating duble-sided dual blades Blade size····························································································· 600 (mm) / 24 (in) Blade pitch··························································································· 41 (mm) / 1.62 (in) Dry weight··························································································· 5.3 (kg) / 11.6 (lbs) Transmission ····································································· Centrifugal clutch, Cam-crank Reduction ratio········································································································· 4.417

Specifications are subject to change without notice.

❲5❳

❲6❳

(1)Read owner's manual before operating this machine. (2)Wear head, eye and ear protection.

If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s).

Never modify your machine. We won't warrant the machine, if you use the remodeled hedge-trimmer or you don't observe the proper usage written in the manual.

WARNING

3. Warning labels on the machine

IMPORTANT

For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make a mistake.

(a)The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP

(b)The direction to close the choke Position: AIR CLEANER COVER

Position: AIR CLEANER COVER

4. Symbols on the machine

Made in Japan

RedMax

IMPORTANT ENGINE INFORMATION

THIS ENGINE CONFORMS TO U.S. EPA PH1 FOR SMALL OFF-ROAD ENGINES.

ENGINE FAMILY : 1KZXS. 0254CD ; EM ENGINE DISPLACEMENT : 22.5cc

REFER TO OWNER’S MANUMAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.

Made in Japan

RedMax

INFORMATION IMPORTANTE CONCERNANT LE MOTEUR

Ce moteur conformc aux normcs U.S. EPA PH1

pour

les petits moteurs tout-terrain.

Type de moteur : 1KZXS. 0254CD ; EM Cylindrée du moteur : 22.5 cc

Se référer au Manuel de l’utilisateur pour les spécifications d’entretien et les réglages.

❲7❳

❲8❳

5. For safe operation

1. Read this manual carefully until you completely understand and follow all safety and operating instructions.

2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product.

3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product.

4. Never allow children or anyone unable to fully understand the directions given in the manual to use the machine.

■ WORKING CONDITION

1. When using the product, you should wear proper clothing and protective equipment.

(1)Helmet (2)Ear protectors (3)Protection goggles or face protector (4)Thick work gloves (5)Non-slip-sole work boots

2. And you should carry with you.

(1)Attached tools (2)Properly reserved fuel (3)Spare blade (4)Things to notify your working area (rope,

warning signs) (5)Whistle (for collaboration or emergency) (6)Hatchet or saw (for removal of obstacles)

3. Do not wear loose clothing, jewelry, short trousers, sandals, or go barefoot. Do not wear anything which might be caught by a moving part of the unit. Secure hair so it is above shoulder length.

■ WORKING CIRCUMSTANCE

1. Never start the engine inside a closed room or building. Exhaust gases contain dangerous carbon monoxide.

2. Never use the product, a. when the ground is slippery or when you can’t

maintain a steady posture.

b. At night, at times of heavy fog, or at any other

times when your field of vision might be limited and it would be difficult to gain a clear view of the working area.

c. During rain storms, during lightning storms, at

times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use the product.

■ WORKING PLAN

1. You should never use the product when under the influence of alcohol, when suffering from exhaustion or lack of sleep, when suffering from drowsiness as a result of having taken cold medicine or at any other time when a possibility exists that your judgment might be impaired or that you might not be able to operate the product properly and in a safe manner.

2. When planning your work schedule, allow plenty of time to rest. Limit the amount of time over which the product is to be used continuously to somewhere around 30~40 minutes per session, and take 10~20 minutes of rest between work sessions. Also try to keep the total amount of work performed in a single day under 2 hours or less.

1. If you don’t observe the working time, or working manner (See ■USING THE PRODUCT), Repetitive Stress Injury(RSI) could occur. If you feel discomfort, redness and swelling of your fingers or any other part of your body, see a doctor before getting worse.

2. To avoid noise complaints, in general, operate product between 8a.m. and 5p.m. on weekdays and 9a.m. to 5p.m. weekends.

Check and follow the local regulations as to sound level and hours of operations for the product.

NOTE

5. For safe operation

❲9❳

WARNING

❲10❳

■ BEFORE STARTING THE ENGINE

1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area. When work is to be performed simultaneously by two or more persons, care should also be taken to constantly look around or otherwise check for the presence and locations of other people working so as to maintain a distance between each person sufficient to ensure safety.

2. Check the condition of working area to avoid any accident by hitting hidden obstacles such as stumps, stones, cans, or broken grass.

Remove any obstacle before beginning work.

3. Inspect the entire unit for loose fasteners and fuel leakage. Make sure that the cutting attachment is properly installed and securely fastened.

■ STARTING THE ENGINE

1. Keep bystanders and animals at least 50feet (15m) away from the operating point. If you are approached, immediately stop the engine.

2. The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position. When starting the engine, place the product onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the engine starts.

IMPORTANT

5. For safe operation

Never place the throttle into the high speed position when starting the engine.

3. After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position. If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized Red Max servicing dealer for repair.

■ USING THE PRODUCT

Cut only materials recommended by the manufacturer. And use only for tasks explained in the manual.

1. Grip the handles firmly with both hands using your whole hand. Place your feet slightly apart (slightly further apart than the width of your shoulders) so that your weight is distributed evenly across both legs, and always be sure to maintain a steady, even posture while working.

2. Maintain the speed of the engine at the level required to perform cutting work, and never raise the speed of the engine above the level necessary.

3. If the unit start to shake or vibrate, turn off the engine and check the whole unit. Do not use it until the trouble has been properly corrected.

4. Keep all parts of your body away from rotating cutting attachment and hot surfaces.

5. Never touch the muffler, spark plug, or other metallic parts of the engine while the engine is in operation or immediately after shutting down the engine. Doing so could result in serious burns or electrical shock.

IMPORTANT

5. For safe operation

❲11❳

WARNING

+ 25 hidden pages