Zenith H27D35DT, H32D35DT, H36D35DT OPERATING GUIDE

®

enjoy the view

installation & operating guide / warranty

table of contents

page

5

 Copyright 2001, Zenith Electronics Corporation

machine numbers H27D35DT H32D35DT

H36D35DT Concierge

TM

TVs

RECORD TV MODEL NUMBER

The model and serial number of the Concierge

TM

TV are located
on the back of the TV cabinet. For future convenience, we
suggest that you record these numbers here:

MODEL NO.____________________________________
SERIAL NO.____________________________________

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.
Unauthorized modification could void the user’s authority to operate this product.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ConciergeTMis a trademark of Zenith Electronics Corporation

© Copyright 2001 Zenith Electronics Corporation

2-WIRE COMM-WARN

PAGE 3

1. Read Instructions

All the safety and operating instructions should be read
before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for
future reference.

4. Heed Warnings

All warnings on the product and in the operating instruc­tions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a
bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or
on an unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or adult,
and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manu­facturer, or sold with the product. Any mounting of the
product should follow the manufacturer’s instructions, and
should use a mounting accessory recommended by the man­ufacturer.

8. Transporting Product

A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product
manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventila­tion and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not
be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in
a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s instruc­tions have been adhered to.

11. Power Sources

This product should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult
your product dealer or local power company. For products
intended to operate from battery power, or other sources,
refer to the operating instructions.

12. Power Cord Polarization

This product is equipped with a polarized alternating-cur­rent power plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety pur­pose of the polarized plug.

13. Power Cord Protection

Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit
from the product.

Important safeguards for you and your new product

This product has been manufactured and tested with your safety in mind. However, improper use can result in potential
electrical shock or fire hazards. To avoid defeating the safeguards that have been built into the new product, please read
and observe the following safety points when installing and using the new product, and save them for future reference.

Observing the simple precautions discussed in this operating guide can help the user get many years of enjoyment and safe
operation that are built into the new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

(Continued on next page)

IMPORTANT SAFETY INSTRUCTIONS

206-3489-O

PORTABLE CART WARNING

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded so
as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical
Code (U.S.A.), ANSI/ NFPA 70 provides information with
regard to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna dis­charge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.

16. Power Lines

An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can
result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service person­nel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following condi­tions:

a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the

product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been
damaged.

f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service
technician has used replacement parts specified by the man­ufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to deter­mine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as
recommended by the manufacturer. The product may slide or
fall, causing serious injury to a child or adult, and serious
damage to the product.

24. Heat

The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.

PAGE 4

206-3489-O

Antenna Lead in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductor
(NEC Section 810-21)

Ground Clamps
Power Service Grounding

Electrode System (NEC
Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical
Code Instructions

NEC - National Electrical Code

IMPORTANT SAFETY INSTRUCTIONS

206-3688-O

PAGE 5

Table of Contents

Turn to the next page to begin the TV set up

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Information . . . . . . . . . . . . . . . . 3 - 4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1. Hook Up TV

Hookup Directory . . . . . . . . . . . . . . . . . . . . . . . . . . 6

TV and other Equipment Hookups

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Cable service . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . 9

Cable service with VCR . . . . . . . . . . . . . . . . . . . . 10

External Speaker . . . . . . . . . . . . . . . . . . . . . . . . 11

Step 2. Channel Search and Reception Setup

Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

(Select Antenna, or cable service and do channel search)

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 13

Guest’s Remote Key Functions . . . . . . . . . . . . . . . . . 14

Installer’s Remote Key Functions . . . . . . . . . . . . . . . . 15

On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . . 16

Step 3. Customize the TV’s Features

Setup Menu (Start with page 12, Auto Program)

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . 17

Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . 18

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Captions (Caption/Text) . . . . . . . . . . . . . . . . . . . 20

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Bass, Treble, Balance, Audio Mode,
Front Surround, Sound Rite, Speakers

Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Contrast, Brightness, Color, Tint, Sharpness, Picture Pref.

Installer Parental Control Menu . . . . . . . . . . . . 24 - 25

Set up Parental Control

Other Menus and On-Screen Displays . . . . . . . . . . . . 26

Managing the Channel Banks . . . . . . . . . . . . 27 - 28 - 29

Installer Menus . . . . . . . . . . . . . . . . . . . . 30 - 31 - 32

LT2000 Quickset II Clone Programmer . . . . . . 33 - 34 - 35

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Guest Operation Section (Copy for guest usage)

Guest Remote Control Key Functions . . . . . . . . . . . . . 39

Guest Parental Control Menu . . . . . . . . . . . . . . . 40 - 41

Guest Menus and On-Screen Displays . . . . . . . . . . . . . 42

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Warranty for Concierge Series TVs . . . . . . . . . . Back Cover

Purchase the Optional Installer’s Remote and Clone Programmer

To preform a normal installation set up, you need an installer’s remote like the LP702, and the LT2000 Quickset II Clone
Programmer - - both are shown and described in later sections. The installer remote allows access to the Installer and,
User menus. The installer remote has Menu, Select, and Adjust keys (Down/Left/Right arrow) keys. The LT2000 Quickset
II Clone Programmer is used to duplicate a TV’s setup and install it on another identical TV. See your Zenith Dealer.

Installer/Hotel Note:

Pages 39, 40, 41, and 42 contain information and menus which the guest can use to operate the TV.
It is recommended that these four pages be copied and included with the literature packet that the
hotel provides to the guest.

Design and specifications are subject to change without prior notice.

If you are using an antenna and no other equipment, go to . . . . . . . . . . . . . page 7

If you have cable service and no other equipment, go to . . . . . . . . . . . . . . page 8

If you are using an antenna and have a VCR, go to . . . . . . . . . . . . . . . . . . page 9

If you have cable service and a VCR, go to . . . . . . . . . . . . . . . . . . . . . . . . page 10

If you want to connect a Matrix speaker, go to . . . . . . . . . . . . . . . . . . . . . page 11

206-3489-O

PAGE 6

Basic Hook-Up Directory

This page will direct you to which page to go to for proper hook up of the TV

IMPORTANT!!
Use this page to decide where you need to begin your set up. First, find the line below that best

describes what you want to do, then go to that page number.

Cable TV
Wall Jack

Cable Box

In
Out

Cable TV
Wall Jack

Cable Box

In
Out

Antenna only

Cable only

Antenna with VCR

Cable and VCR

External Speaker

Locate the Antenna/Cable jack on the back of the TV.
Connect the antenna wire that runs from the wall

directly to this jack, according to one of the diagrams
to the right.

Remove the back of the remote and put in two AA
batteries.

Plug in the TV. Do not plug it into a switched outlet.
The TV is designed to operate on standard current,
120-volt 60 Hertz AC. Do not attempt to operate it
on DC power.

Go to page 12 to Auto Program the TV.

Mini glossary

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire

sticking through the middle, and it screws onto the threaded jack on the back of your TV.
A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws

on one end and a round opening with a wire sticking out on the other end.

206-3489-O

PAGE 7

Hook Up Your Antenna to the TV

300 TO 75 OHM
ADAPTER

TV Back

Flat Wire

(300 ohm)

Antenna

300/75 ohm

Adapter

TV Back Connections Panel

(Expanded View)

R- AUDIO- L

VIDEO

IN

MATRIX

OUT

IN

ANTENNA

CABLE

M.P.I.

TV Back

TV Back Connections Panel

(Expanded View)

RF Coaxial Wire

(75ohm)

Antenna

R- AUDIO- L

VIDEO

IN

MATRIX

OUT

IN

ANTENNA

CABLE

M.P.I.

Back of
Remote

120 V AC
60 Hz

1
2

3

4

5

Connect an off-air antenna to the TV

If you have a 75 ohm RF cable, then you don’t need
any adapters!

A 300 to 75 ohm adapter is not included with the
Zenith TV.

206-3489-O

PAGE 8

Hook Up Your Cable (CATV) to the TV

If you’re using a cable box, leave the TV on channel 3
or 4 and use your cable box to change channels.

If you’re using a cable box, Auto Program might only
find the channel your cable service is on (usually chan­nel 3 or 4). Don’t worry, that’s all you need!

Cable TV
Wall Jack

RF Coaxial Wire

(75ohm)

TV Back

R- AUDIO- L

VIDEO

IN

MATRIX

OUT

IN

ANTENNA

CABLE

M.P.I.

Cable TV
Wall Jack

Cable Box

In

Out

RF Coaxial Wire

(75ohm)

3 4

output

switch

TV Back

R- AUDIO- L

VIDEO

IN

MATRIX

OUT

IN

ANTENNA

CABLE

M.P.I.

Locate the Antenna/Cable jack on the back of the
TV.

Connect the wire that runs from the wall directly
to this jack, according to one of the diagrams to
the right.

Remove the back of the remote and put in two AA
batteries.

Plug in the TV. Do not plug it into a switched
outlet. The TV is designed to operate on normal
current, 120-volt 60 Hertz AC. Do not attempt to
operate it on DC power.

Go to page 12 to Auto Program the TV.

Back of
Remote

120 V AC
60 Hz

1
2

3

4

5

Connect cable service to the TV

Locate the Antenna/Cable In jack on the back of
the VCR.

Connect the wire that runs from the antenna,
according to one of the diagrams to the right. As
required, make the other connections as shown to
the right.

Remove the back of the remote, put in two AA bat­teries.

Plug in the TV. Do not plug it into a switched out­let. The TV is designed to operate on standard cur­rent, 120-volt 60 Hertz AC. Do not attempt to oper­ate it on DC power.

Go to page 12 to Auto Program the TV.

206-3489-O

PAGE 9

Hook Up Antenna and VCR to the TV

Flat Wire

(300 ohm)

Antenna

300/75 ohm

Adapter

A/V cables

not included

with TV

In

Out

Audio

Video

3 4

VCR Back

VCR Back AV panel

output
switch

TV Back

Connections Panel

(Expanded View)

R- AUDIO- L

VIDEO

IN

MATRIX

OUT

IN

TV Back

ANTENNA

CABLE

M.P.I.

A/V cables

not included

with TV

In

Out

Audio

Video

3 4

VCR Back

VCR Back AV panel

output
switch

TV Back

Connections Panel

(Expanded View)

R- AUDIO- L

VIDEO

IN

MATRIX

OUT

IN

TV Back

RF Coaxial Wire

(75ohm)

Antenna

ANTENNA

CABLE

M.P.I.

Back of
Remote

120 V AC
60 Hz

1

2

3

4

5

Connect an off-air antenna and VCR to the TV

No A/V cables are included with the Zenith TV.
Without A/V cables, most VCRs will not play

videocassettes in stereo sound.

Locate the Antenna/Cable In jack on the back of
the VCR.

Connect the wire that runs from the wall, accord­ing to one of the diagrams to the right. As
required, make the other connections as shown to
the right.

Remove the back of the remote, put in two AA
batteries.

Plug in the TV. Do not plug it into a switched
outlet. The TV is designed to operate on standard
current, 120-volt 60 Hertz AC. Do not attempt to
operate it on DC power.

Go to page 12 to Auto Program the TV.

PAGE 10

206-3489-O

Hook Up Cable Service (CATV) and VCR

A/V cables

not included

with TV

In

Out

R - L
Audio

Video

3 4

VCR Back

VCR Back AV Panel

output
switch

TV Back

Connections Panel

(Expanded View)

R- AUDIO- L

VIDEO

IN

MATRIX

OUT

IN

TV Back

Cable TV
Wall Jack

Round Wire (75ohm)

Cable Box

In

Out

3 4

output
switch

ANTENNA

CABLE

M.P.I.

Cable TV
Wall Jack

Round Wire (75ohm)

A/V cables

not included

with TV

In

Out

R - L
Audio

Video

3 4

VCR Back

VCR Back AV Panel

output
switch

TV Back

Connections Panel

(Expanded View)

R- AUDIO- L

VIDEO

IN

MATRIX

OUT

IN

TV Back

ANTENNA

CABLE

M.P.I.

Back of
Remote

120 V AC
60 Hz

1

2

3

4

5

Connect a VCR and Cable service to the TV

Leave the VCR and the television tuned to channel three
and use the cable box to change channels.

No A/V cables are included with your TV. Without A/V
cables, most VCRs will not play videocassettes in stereo
sound.

PAGE 11

206-3489-O

External Speaker Hook Up

A/V cables

not included
with TV

R- AUDIO- L

VIDEO

IN

MATRIX

OUT

IN

Audio In

Speaker back

TV back panel

(expanded view)

TV Back

ANTENNA

CABLE

M.P.I.

1
2

Locate the Audio In jack on the back of the
speaker.

Connect a standard audio cable from the
Matrix Out jack on the TV, to the Audio In
jack on the external speaker.

Connect an external speaker to the TV

PAGE 12

206-3489-O

Auto Program (Channel Search)

1

2

3
4
5

6
7

TIMER

CH PREVIEW

ENTER

1

2

3

4

5

6

7

8

9

0

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

CC

MENU

ALARM

ADJ

ADJ

SELECT

3/5

4/6

1

7
2

Use Auto Program to specify Antenna or cable service
incoming signal source and automatically store all of the
channels that are found by channel search

With the Installer remote control in hand, press the
POWER key to turn on the TV.

Press MENU repeatedly until the Setup menu appears.
Using SELECT on the remote control, highlight Auto

Program on the screen.
Press the Right or Left ADJ (Adjust) arrow to go to the

Auto Program screen.
Using SELECT, choose either Cable TV or Off-Air Antenna

on your screen. (The flashing option is selected.)
Press the Right or Left ADJ arrow to begin the Channel

Search.
Press ENTER when finished.

Mini glossary

OFF-AIR-ANTENNA If the guest can only view over-the-air broadcasts, select Antenna.
CABLE If you provide cable service to your guests, select Cable.

Auto Program finds channels being received by the TV tuner.

Cable will not work unless a cable service is present.

PAGE 13

206-3489-O

Front Panel Controls

AUDIO

VIDEO

CAPTION

VOL

VOL

CH

CH

OFF

ON

IN

LEFT

RIGHT

1

4

1
2

3
4

5

2

3

Typical Front Panel Controls

The Front Audio/Video jacks are a direct source connection.
If you have a device plugged into the front Video jack, you
will not be able to change channels until you have
unplugged the front Video jack.

Front panel control menu operation buttons are not labeled
and are not usually available to the guest.

You can use Ch to select channels and Vol to set the vol­ume level regardless of the key defeat setting.

There are three jacks on the front of the TV that make con­necting Audio/Video devices like camcorders very simple.

To use the front jacks as the signal source, simply plug a
composite video cable into the VIDEO jack. The TV will auto­matically change its source setting to CAMPORT, as indicated
on the channel selection screen.

Video

Video input.

Left/Right Audio

Audio stereo input.

Use the front control panel to access the menus or just operate the TV
Note: Item 10 Key Defeat, in the installer’s menu allows the installer to:

Set Menu Option 10, Key defeat to “0” - Front panel controls give access to menus.
Set Menu Option 10, Key defeat to “1” - Menus not available with front panel controls.

Press ON/OFF to turn on your TV.
To access the menus press the MENU button on the

control panel. Cycle through the various menus by
pressing the button repeatedly.

Press the SELECT button repeatedly to highlight the
option you want to modify.

Press either the Right or Left ADJUST button to modi­fy the option you have chosen.

Press CAPTIONS to turn captions on and off.
The menu will disappear after a few seconds.

5

PAGE 14

206-3489-O

Guest Remote Key Functions

TIMER ALARM

CH PREVIEW

ENTER

1

2

3

4

5

6

7

8

9

0

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

CC

remote control part number

SC652

124-213-02

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off.

CHANNEL (UP/DOWN)

Scrolls through available channels, and the
Video Channel (Audio/Video source).

MUTE

Turns sound Off and On, while the picture
remains.

ENTER

Press to view the

Channel/Time/Audio display or to

remove any on-screen

display or menu.

NUMBER KEYPAD

Used to key-in numbers and select channels
directly: key-in channel numbers and press
ENTER to go to new channel

.

TIMER

Press repeatedly to set the TV turn-off

time from 10 minutes up to 4-hours.

Sets AM or PM in Clock/Alarm menus.

VOLUME (LEFT/RIGHT)

Adjusts the sound level.

CHANNEL PREVIEW

Displays the available TV channels, including
access to guest’s Parental Control menu (if
Active). Allows guest to select the Video
source. (Use the Audio/Video jacks on the
back of the TV as the source of the picture
and sound.)

CC (CLOSED CAPTIONING)

Direct access to closed captions.

Press ENTER to exit.

A quick list of the keys on the guest remote and what they do

ALARM

Press to go to the Alarm menu. Set a time for
the TV to turn itself on.

NOTE:

The channel and volume keys can be used by the guest to select and adjust the Parental
Control settings, if the installer activates the Parental Control (V-CHIP) option in the
Installer menu.