Zenith H2035DT, H2535DT OPERATING GUIDE

machine numbers	H2035DT	H2535DT

ConciergeTM

Direct-View

Television

Receiver with

FM Radio

i n s t a l l a t i o n & o p e r a t i n g g u i d e / w a r r a n t y

RECORD YOUR MODEL NUMBER

The model and serial number of your new TV are located on the back of the TV cabinet. For your future convenience, we suggest that you record these numbers here:

MODEL NO.____________________________________

SERIAL NO.____________________________________

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product.

Concierge is a trademark of Zenith Electronics Corporation © Copyright 1999 Zenith Electronics Corporation

IMPORTANT SAFETY INSTRUCTIONS

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4.Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

7. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care. may

.

9. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Line-Cord Polarization

This product is equipped with a polarized alternating-cur- rent line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

(Continued on next page)

206-3489-O

P A G E 3

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Example of Grounding According to National Electrical Code Instructions

Ground Clamp

		Antenna Lead in Wire
		Antenna Discharge Unit
		(NEC Section 810-20)
		Grounding Conductor
Electric Service		(NEC Section 810-21)
Equipment		Ground Clamps
		Power Service Grounding
		Electrode System (NEC
		Art 250, Part H)

NEC - National Electrical Code

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.If the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the product.

c.If the product has been exposed to rain or water.

d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e.If the product has been dropped or the cabinet has been damaged.

f.If the product exhibits a distinct change in performance.

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

P A G E 4

206-3489-O

Table of Contents

Turn to the next page to begin the TV setup

Safety Warnings	2
Important Safety Information	3
Table of Contents	5
Step 1. Hook Up TV
Hookup Directory	6
TV and other Equipment Hookups
Antenna	7
Cable service	8
Antenna with VCR	9
Cable service with VCR	10
External Speaker	11

Step 2. Channel Search and Reception Setup

Auto Program	12
(Select Antenna, or cable service and perform
channel search)
Front Panel Controls	13
Guest’s Remote Key Functions	14
Installer’s Remote Key Functions	15
On-Screen Menus Overview	16
Step 3. Customize the TV’s Features
Setup Menu (Start with page 12, Auto Program)
Add/Del/Blank	17
Channel Labels	18
Timer Setup	19
Clock Set	20
Captions Caption/Text	21
Language	22
Audio Menu	23
Bass, Treble, Balance, Audio Mode,
Front Surround, Sound Rite, Speakers

Video Menu	24
Contrast, Brightness, Color, Tint, Sharpness,
Picture Pref.
Installer Parental Control Menu	25
Setup Parental Control
Other Menus and On-Screen Displays	27
FM Radio
FM Radio Auto Program	28
FM Radio On-Screen Menus	29
FM Radio Audio Menu	30
Channel Banks
Managing the Channel Banks	31
Installer Menus
Installer Menus	34
LT1500 Quickset Clone Programmer	37
Maintenance	40
Trouble Shooting	41
Glossary	42
Guest Operation Section (Copy for guest usage)
Guest Remote Control Key Functions	43
Guest Parental Control Menu	44
Guest Menus and On-Screen Displays	46
Guest FM Radio Operation/Menus	47
Warranty for ConciergeTM Series TVs	Back Cover

Installer/Hotel Note:

Pages 43, 44, 45, 46, and 47 contain information and menus which the guest can use to operate the TV and FM Radio. It is recommended that these five pages be copied and included with the literature packet that the hotel provides to the guest.

Purchase the Optional Installer’s Remote and Clone Programmer

To preform the installation setup, you need an installer’s remote like the LP702, and the LT1500 Clone Programmer - - both are shown and described in later sections. The installer remote allows access to the Installer Menus, User menus, and Source/Channel Banks. The installer remote has Menu, Select, and Adjust Keys (Up/Down/Left/Right arrows) and Source/Channel Bank Keys. The LT1500 Clone Programmer is used to duplicate a TV’s setup and install it on another TV. See your Zenith Dealer.

Design and specifications are subject to change without prior notice.

206-3488-O

P A G E 5

External Speaker

P A G E 6

Antenna only

Cable only

Basic Hook-Up Directory

This page will direct you to which page to go to for proper hook up of the TV

IMPORTANT!!

Use this page to decide where you need to begin the set up. First, find the line below that best describes what you want to do, then go to that page number.

If you are using an antenna and no other equipment, go to . . . . . . . . . . . . . . . . . . page 7

If you have cable and no other equipment, go to . . . . . . . . . . . . . . . . . . . . . . . . . page 8

Cable TV wall jack

In

Cable box

Out

Antenna with VCR

If you are using an antenna and have a VCR, go to . . . . . . . . . . . . . . . . . . . . . . .

page 9

Cable and VCR	If you have cable and a VCR, go to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .		page 10
	Cable TV
	wall jack
	In	Cable box
	Out

If you want to connect a Matrix speaker, go to . . . . . . . . . . . . . . . . . . . . . . . . . . .page 11

206-3489-O

Hook Up an Antenna to the TV

Connect an off-air antenna to the TV

	1	Locate the Antenna/Cable jack on the back of the TV.
	2	Connect the cable that runs from the wall directly to
		this jack, according to the diagram to the right.
	3	Remove the back of the remote and put in two AA bat-
		teries.

back of remote

4	Plug in the TV. Do not plug it into a switched outlet.
	The TV is designed to operate on standard current, 120-
	volt 60 Hertz AC. Do not attempt to operate it on DC
	Current.

	TV back
Antenna
Flat wire
(300 ohm)	ANTENNA
	CABLE
	VIDEO	MATRIX
	IN	OUT
	M.P.I.

R- AUDIO- L

IN

	300/75 ohm	TV back panel
		(expanded view)
	Adapter

5	Go to page 12 to Auto Program the TV.

TV back

Antenna

If you have a 75 ohm RF cable, then you don’t need any adapters!

A 300 to 75 ohm adapter is not included with the Zenith TV.

RF coaxial wire	ANTENNA
(75ohm)	CABLE
	VIDEO	MATRIX
	IN	OUT

M.P.I.

R- AUDIO- L

IN

TV back panel (expanded view)

Mini glossary

75 OHM RF CABLE

300 TO 75 OHM ADAPTER

The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking through the middle, and it screws onto the threaded jack on the back of your TV.

A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end.

206-3489-O

P A G E 7

Hook Up Cable Service (CATV)

Connect cable service to the TV

	1	Locate the Antenna/Cable jack on the back of
		the TV.
	2	Connect the cable that runs from the wall
		directly to this jack, according to the diagram

		to the right.
	3	Remove the back of the remote and put in two
		AA batteries.

back of remote

	4	Plug in the TV. Do not plug it into a switched
		outlet. Your TV is designed to operate on stan-
		dard current, 120-volt 60 Hertz AC. Do not
		attempt to operate it on DC Current.

Go to page 12 to Auto Program the TV.

5

If you’re using a cable box, leave the TV on channel 3 or 4 and use your cable box to change channels.

If you’re using a cable box, Auto Program might only find the channel your cable service is on (usually channel 3 or 4). Don’t worry, that’s all you need!

TV back

Cable TV wall jack

ANTENNA

CABLE

RF coaxial wire (75ohm)

VIDEO	MATRIX
IN	OUT

M.P.I.

R- AUDIO- L

IN

Cable TV wall jack

TV back

In	Cable box
Out	output
	switch 3 4
	RF coaxial wire (75ohm)	ANTENNA
		CABLE
		VIDEO	MATRIX
		IN	OUT

M.P.I.

R- AUDIO- L

IN

P A G E 8

206-3489-O

Hook Up Antenna and VCR to the TV

Connect an off-air antenna and VCR to the TV

	1	Locate the Antenna/Cable jack on the back of the VCR.
	2	Connect the cable that runs from the antenna directly to
		this jack, according to the diagram to the right. As
		required, make the other connections as shown to the
		right.
	3	Remove the back of the remote, put in two AA batteries.

back of remote

4 Plug in the TV. Do not plug it into a switched outlet. The TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC Current.

5 Go to page 12 to Auto Program the TV.

No A/V cables are included with the Zenith TV.

Without A/V cables, most VCRs will not play videocassettes in stereo sound.

Antenna

Flat wire (300 ohm)

VCR back

VCR back AV panel

300/75 ohm	In	output	3 4
Adapter		switch
TV back	Out	Video Audio

ANTENNA

CABLE

VIDEO	MATRIX
IN	OUT

M.P.I.

R- AUDIO- L

IN

TV back panel (expanded view)

A/V cables not included with TV

Antenna
			VCR back
	RF coaxial wire	VCR back AV panel
	(75ohm)	In	output
			switch 3	4
	RF coaxial wire	Out	Video Audio
	(75ohm)
TV back	not included
	with TV

ANTENNA

CABLE

VIDEO	MATRIX
IN	OUT

M.P.I.

R- AUDIO- L

IN

TV back panel (expanded view)

A/V cables not included with TV

206-3489-O

P A G E 9

Hook Up Cable Service (CATV) and VCR

Connect a VCR and Cable service to the TV.

1	Locate the Antenna/Cable jack on the back of the
	VCR.
2	Connect the cable that runs from the wall directly
	to this jack, according to the diagram to the
	right. As required, make the other connections as
	shown to the right.
3	Remove the back of the remote, put in two AA
	batteries.

			back of
4			remote
	Plug in the TV. Do not plug it into a switched
	outlet. The TV is designed to operate on standard
	current, 120-volt 60 Hertz AC. Do not attempt to
	operate it on DC Current.

5 Go to page 12 to Auto Program the TV.

Leave the VCR and the television tuned to channel three and use the cable box to change channels.

No A/V cables are included with your TV. Without A/V cables, most VCRs will not play videocassettes in stereo sound.

Cable TV wall jack

	VCR back
VCR back AV panel
Round wire (75ohm)	output
In
	switch 3 4
Out	Video Audio

TV back

ANTENNA

CABLE

VIDEO	MATRIX
IN	OUT

M.P.I.

R- AUDIO- L

IN

TV back panel

(expanded view)

A/V cables not included with TV

Cable TV wall jack

In	Cable box		VCR back
Out	output
	switch 3 4
	Round wire (75ohm)	VCR back AV panel
			output
		In
			switch 3 4
		Out	Video Audio
TV back

ANTENNA

CABLE

VIDEO	MATRIX
IN	OUT

M.P.I.

R- AUDIO- L

IN

TV back panel

(expanded view)

A/V cables not included with TV

P A G E 1 0

206-3489-O

External Speaker Hook Up

Connect an external speaker to the TV.

1	Locate the Audio In jack on the back of the
	speaker.
2	Connect a standard audio cable from the Matrix
	Out jack on the TV, to the Audio In jack on the

external speaker.

TV back

ANTENNA

CABLE

VIDEO	MATRIX
IN	OUT

M.P.I.

R- AUDIO- L

IN

TV back panel (expanded view)

Speaker back

Audio In

A/V cables not included with TV

206-3489-O

P A G E 1 1

Auto Program (Channel Search)

Use Auto Program to specify Antenna or cable service incoming signal source and automatically store all of the channels that are found by channel search

1					With the Installer remote control in hand,	press the
					POWER key to turn on the TV.
2					Press MENU repeatedly so the Setup menu	appears.	1
3					Using SELECT on the remote control, highlight Auto
					Program on the screen.
4					Press a Right or Left ADJ (Adjust) arrow to reach the
					Auto Program screen.
5					Using SELECT, choose either Cable TV or Off-Air Antenna
					on your screen. (The flashing option is selected.)
6					Press a Right or Left ADJ arrow to begin the Channel
					Search.
7					Press ENTER when finished.
					Note: Auto Program finds channels being received by the TV
					tuner.
					Cable will not work unless the lodge provides a cable
					(If the Auto Program line appears in red, then it did not pass
					one of the internal tests. To set Auto Program to white, set the
					upper nibble of the EEPROM location $1FFh to $B0h.)

Mini glossary
OFF-AIR-ANTENNA	If the guest can only view over-the-air broadcasts, select Antenna.
CABLE	If you provide cable service to your guests, select Cable.

POWER

MUTE

	FLSHBK
CC
TV/FM
UME
VOL	CHANNEL

1 2 3

4 5 6

7 8 9

TIMER MENU	BANK
SELECT	CHPREVIEW
ADJ	ADJ

7

2

P A G E 1 2

206-3489-O

Front Panel Controls

Using the front control panel to access the menus

	1	Press ON/OFF to turn on your TV.
	2	To access the menus press the MENU button on the
		control panel. Cycle through the various menus by
		pushing the button repeatedly.
	3	Press the SELECT button repeatedly to highlight the
		option you want to modify.
	4	Press either the Right or Left ADJUST button to modi-
		fy the option you have chosen.
	5	The menu will disappear after a few seconds.

There are three jacks on the front of the TV that make connecting Audio/Video devices like camcorders very simple.

To use the front jacks as the signal source, simply plug a composite video cable into the VIDEO jack. The TV will automatically change its source setting to CAMPORT, as indicated on the channel selection screen.

The Front Audio/Video jacks are a direct source connection. If you have a device plugged into the front Video jack, you will not be able to change channels until you have unplugged the front Video jack.

Typical Front Panel Controls

VIDEO AUDIO

CAPTION

VOL

VOL

CH

IN LEFT RIGHT

3

Video

Connects the video signals from any piece of equipment.

Left/Right Audio Used for stereo sound from various types of equipment.

206-3489-O

P A G E 1 3

Guest Remote Key Functions

A quick list of the keys on the guest remote and what they do

CC (CLOSED CAPTIONING)

Direct access to closed captions. Press ENTER to exit.

POWER

Turns TV On or Off.

TV/FM

Switches between TV and FM radio modes.

VOLUME (LEFT/RIGHT)

Adjusts the sound level.

ENTER

Press to view the Channel/Time/Audio display or to remove any on-screen display or menu.

TIMER

Press repeatedly to set the TV turn-off time from 10 minutes up to 4-hours.

POWER

MUTE

	FLSHBK
CC
TV/FM
UME
VOL	CHANNEL

1 2 3

4 5 6

7 8 9

0 ENTER

TIMER

ALARM

CH PREVIEW

remote control part number

SC692

124-213-03

NOTE:

The channel and volume keys can be used by the guest to select and adjust the Parental Control settings, if the installer activates the Parental Control option in the Installer Menu.

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

MUTE

Turns sound Off and On, while the picture remains.

CHANNEL (UP/DOWN)

Scrolls through available channels, and the Video Channel (Audio/Video source).

NUMBER KEYPAD

Used to key-in numbers and select channels directly: key-in channel numbers and press ENTER to go to new channel.

ALARM

Press to display menu, then follow on-screen instructions to set a wake-up time.

CHANNEL PREVIEW

Displays the available TV channels, including access to guest’s Parental Control menu (if Active). Allows guest to select the Video source. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.)

P A G E 1 4

206-3488-O

Installer Remote Key Functions

A quick list of the keys on the LP702 installer’s remote and what they do

CC (CLOSED CAPTIONING)

Direct access to closed captions. Press ENTER to exit.

POWER

Turns TV On or Off.

TV/FM

Selects TV or Radio mode on TVs equipped with FM radio.

VOLUME (LEFT/RIGHT)

Adjusts the sound levels.

ENTER

Press to view the Channel/Time display or to remove any on-screen display or menu.

TIMER

Press repeatedly to adjust TV turn-off time from 10 minutes up to 4-hours.

MENU/SELECT/ADJ (ADJUST)

Adjusts on-screen menus and options. Press MENU repeatedly to scroll through menus. Use SELECT to choose an option and ADJ (adjust) Left/Right to change the selected option.

POWER

MUTE

	FLSHBK
CC
TV/FM
UME
VOL	CHANNEL

1 2 3

4 5 6

7 8 9

0 ENTER

TIMER MENU BANK

SELECT CHPREVIEW

ADJ

ADJ

remote control part number

LP702

124-213-04

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

MUTE

Turns sound Off and On, while the picture remains.

CHANNEL (UP/DOWN)

Scrolls through available channels.

NUMBER KEY PAD

Selects channels directly and enters numeric values for some options.

BANK

Press and repeat to select a Channel Memory Bank: Bank 1, 2, 3, or 4.

CHANNEL PREVIEW

Gives installer access to the guest’s menus. Displays the available TV channels and hotel guest’s Parental Control menu (if active). Selects the Video source. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.)

206-3489-O

P A G E 1 5