Zenith H19E34Y, H20E34Y, H25E34Y OPERATING GUIDE

© Copyright 2002, Zenith Electronics Corporation
table of contents
page
5
Installation / Operating Guide | Warranty
Model Numbers | H19E34Y | H20E34Y | H25E34Y ConciergeTMTVs
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
POWER CORD POLARIZATION:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is: Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069, USA. Phone: 1-847-941-8000.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
2-WIRE COMM WARN
ConciergeTMis a trademark of Zenith Electronics Corporation
© Copyright 2002 Zenith Electronics Corporation
RECORD THE MODEL NUMBER
The model and serial number of the ConciergeTMTV are located on the back of the cabinet. For future reference, we suggest that those numbers be recorded here:
MODEL NO.____________________________________
SERIAL NO.____________________________________
For Customer Support/Service please call:
1-888-865-3026
www.zenith.com
PAGE 3
206-3743
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
The safety and operating instructions should be retained for future reference.
4. Heed Warnings
All warnings on the product and in the operating instruc­tions should be adhered to.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Water and Moisture
Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
7. Accessories, Carts, and Stands
Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
8. Transporting Product
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
9. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
10. Ventilation
Slots and openings in the cabinet are provided for ventila­tion and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruc­tions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Power Cord Polarization
This product is equipped with a polarized alternating-cur­rent power plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety pur­pose of the polarized plug.
13. Power Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
Important safeguards for you and your new product
This product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into the new product, please read and observe the following safety points when installing and using the new product, and save them for future reference.
Observing the simple precautions discussed in this operating guide can help get many years of enjoyment and safe opera­tion that are built into the new product.
(Continued on next page)
IMPORTANT SAFETY INSTRUCTIONS
PORTABLE CART WARNING
(Continued from previous page)
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna dis­charge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
15. Lightning
For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
16. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
18. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
19. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service person­nel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following condi­tions:
a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance.
21. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the man­ufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to deter­mine that the product is in proper operating condition.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.
24. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
PAGE 4
206-3490-O
Antenna Lead in Wire
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductor (NEC Section 810-21)
Ground Clamps Power Service Grounding
Electrode System (NEC Art 250, Part H)
Ground Clamp
Electric Service
Equipment
Example of Grounding According to National Electrical Code Instructions
NEC - National Electrical Code
IMPORTANT SAFETY INSTRUCTIONS
206-3745
PAGE 5
Table of Contents
Turn to the next page to begin the TV set up
Purchase the Optional Installer’s Remote
To perform a normal installation set up, you need an installer’s remote like the LP702. The LP702 is shown and described in later sections. The installer remote allows access to the Installer’s menus, and User menus. The installer remote has Menu, Select, and Adjust Keys (Down/Left/Right arrow) keys.. To purchase the LP702 remote, see your Zenith Dealer.
Installer/Hotel Note:
Pages 13, 32, 33, 34, and 35 contain information and menus which the guest can use to operate the TV. It is recommended that these four pages be copied and included with the literature packet that the hotel provides to the guest.
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safety Information . . . . . . . . . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 1. Hook Up TV
TV and other Equipment Hookups
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cable service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cable service with VCR . . . . . . . . . . . . . . . . . . . . . . . 9
External Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Step 2. Channel Search and Reception Setup
Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
(Select Antenna, or cable service and perform channel search)
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 12
Guest Remote Key Functions . . . . . . . . . . . . . . . . . . 13
Installer’s Remote Key Functions . . . . . . . . . . . . . . . . 14
On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . 15
Step 3. Customize the ConciergeTMTV’s Features
Setup Menu (Start with page 11, Auto Program)
Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Timer (On/Off Timer) . . . . . . . . . . . . . . . . . . . . . . . 19
Captions (Caption/Text) . . . . . . . . . . . . . . . . . . . . . 20
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installer Parental Control Menu . . . . . . . . . . . . 23 - 24
Other Menus and On-Screen Displays . . . . . . . . . . . . . 25
Managing the Channel Banks . . . . . . . . . . . . 26 - 27 - 28
Installers Menus . . . . . . . . . . . . . . . . . . . . 29 - 30 - 31
LT2000 Quickset II Clone Programmer . . . . . . 32 - 33 - 34
Guest Operation Section (Copy for guest usage)
Guest Remote Control Key Functions . . . . . . . . . . . . . 13
Guest Parental Control Menu . . . . . . . . . . . . 35 - 36 - 37
Guest Menus and On-Screen Displays . . . . . . . . . . . . . 38
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 - 43
Warranty for Concierge
TM
Series TVs . . . . . . . . . Back Cover
ConciergeTMis a trademark of Zenith Electronics Corporation
PAGE 6
206-3745
Mini glossary
75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire
sticking through the middle, and it screws onto the threaded jack on the back of your TV.
A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end.
Antenna Hook Up
Connect an over-the-air antenna to the Concierge TV
If you have a 75 ohm RF cable, then you don’t need any adapters!
A 300 to 75 ohm adapter is not included with the Zenith Concierge TV.
300 TO 75 OHM ADAPTER
Antenna
Flat wire
(300 ohm)
300/75 ohm
Adapter
TV Back Panel
(Expanded View)
TV Back
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
RF coaxial wire
(75ohm)
Antenna
TV Back Panel
(Expanded View)
TV Back
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
Locate the Antenna/Cable jack on the back of the Concierge TV.
Connect the antenna wire that runs from the wall, according to one of the diagrams to the right.
Remove the back of the remote and put in two AA batteries.
Plug in the TV. Concierge TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power.
Go to page 11 to Auto Program the TV.
back of
remote
120 V AC 60 Hz
1
2
3
4
5
PAGE 7
206-3745
Cable Service Hook Up (CATV)
If you’re using a cable box, leave the TV tuned to channel 3 or 4 and use the cable box to change channels.
If you’re using a cable box, Auto Program might only find the channel your cable service is on (usually channel 3 or 4).
Cable TV Wall Jack
RF Coaxial Wire
(75ohm)
TV Back Panel
(Expanded View)
TV Back
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
Cable TV Wall Jack
Cable Box
In
Out
3 4
output
switch
RF Coaxial Wire
(75ohm)
TV Back Connections Panel
(Expanded View)
TV Back
VIDEO
IN
Super
Port
SPEAKER
OUT
AUDIO
IN
ANTENNA
CABLE
M.P.I.
Locate the Antenna/Cable jack on the back of the Concierge TV.
Connect the cable service wire that runs from the wall, according to one of the diagrams to the right.
Remove the back of the remote and put in two AA batter­ies.
Plug in the TV. The Concierge TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power.
Go to page 11 to Auto Program the Concierge TV.
back of
remote
120 V AC 60 Hz
1
2
3
4
5
Connect cable service to the Concierge TV
PAGE 8
206-3745
Antenna With VCR Hook Up
Connect an off-air antenna and VCR to the Concierge TV
No A/V cables are included with the TV.
Flat wire
(300 ohm)
Antenna
300/75 ohm
Adapter
TV Back Panel
(Expanded View)
TV Back
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
In
Out
Audio
Video
3 4
VCR Back
VCR Back AV Panel
output switch
A/V Cables
Not included
with TV
RF Coaxial Wire
(75ohm)
Antenna
TV Back Panel
(Expanded View)
TV Back
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
In
Out
Audio
Video
3 4
VCR Back
VCR Back AV Panel
output switch
Locate the Antenna/Cable jack on the back of the VCR.
Connect the antenna wire that runs from the antenna, according to one of the diagrams to the right. Make other connections as needed.
Remove the back of the remote and put in two AA batteries.
Plug in the TV. The Concierge TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power.
Go to page 11 to Auto Program the TV.
back of
remote
120 V AC 60 Hz
1
2
3
4
5
PAGE 9
206-3745
Cable Service (CATV) with VCR Hook Up
Connect a VCR and Cable service to the Concierge TV
Leave the VCR and the television tuned to channel three and use the cable box to change channels.
No A/V cables are included with the TV.
Cable TV Wall Jack
Cable box
In
Out
3 4
output switch
A/V Cables
Not included
with TV
RF Coaxial Wire
(75ohm)
TV Back Panel
(Expanded View)
TV Back
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
In
Out
Audio
Video
3 4
VCR Back
VCR Back AV Panel
output switch
Cable TV Wall Jack
A/V Cables
Not included
with TV
RF Coaxial Wire
(75ohm)
TV Back Panel
(Expanded View)
TV Back
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
In
Out
Audio
Video
3 4
VCR Back
VCR Back AV Panel
output switch
Locate the Antenna/Cable jack on the back of the VCR.
Connect the cable service wire that runs from the wall, according to one of the dia­grams to the right. Make other connections as needed.
Remove the back of the remote and put in two AA batteries.
Plug in the TV. The Concierge TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC power.
Go to page 11 to Auto Program the TV.
back of
remote
120 V AC 60 Hz
1
2
3
4
5
PAGE 10
206-3745
External Speaker Hook Up
Locate the Audio In jack on the back of the exter­nal speaker.
Connect a standard audio cable from the Speaker Out jack on the TV, to the Audio In jack on the external speaker.
Audio In
Speaker back
TV Back Panel
(Expanded View)
TV Back
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
1
2
Connect an external speaker to the Concierge TV
PAGE 11
206-3745
Auto Program (Channel Search)
Use Auto Program to specify Antenna or cable service incoming signal source and automatically store all of the channels that are found by channel search
Using an Installer remote control, press the POWER key to turn on the Concierge TV.
Press the MENU key to show the SETUP MENU.
Using SELECT on the remote control, highlight AUTO PROGRAM on the screen.
Press the Right or Left ADJ (Adjust) arrow to go to the Auto Program menu.
Using SELECT, choose either CABLE TV or OFF AIR ANTENNA on your screen.
Press the Right or Left ADJ arrow key to begin the Channel Search.
Press ENTER when the channel search is complete.
1
2
3
4
5
6
7
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
MENU
ALARM
ADJ
ADJ
SELECT
3/5
AUTO PROGRAM ADD/DEL/BLNK CH. LABELS CLOCK SET TIMER CAPTIONS LANGUAGE
TO PROGRAM
Mini glossary
OFF AIR ANTENNA If the guest can only view over-the-air broadcasts, select Antenna.
CABLE If you provide cable service to your guests, select Cable.
Note: Auto Program finds channels being received by the TV tuner.
Cable will not work unless the lodge provides a cable service.
4/6
1
7 2
PAGE 12
206-3745
Front Panel Controls
1
2
3
4
Use the front control panel to access the menus or just operate the TV
Note: Item 10 Key Defeat, in the installer’s menu allows the installer to: Set Menu Option 10, Key defeat to “0” - Front panel controls give access to menus. Set Menu Option 10, Key defeat to “1” - Menus not available with front panel controls.
Front panel control menu operation buttons are not labeled and are not usually available to the guest.
You can use Channel to tune to available channels and Volume to set the sound level, regardless of the key defeat setting.
Camport jacks are not available on some models.
Press POWER to turn on your TV.
To access the menus, press the MENU button on the control panel. Cycle through the various menus by pressing MENU repeatedly.
Use the SELECT button to highlight the option you want to modify.
Use either the Right or Left ADJUST button to modify the option you have chosen.
Press CAPTIONS to turn captions on and off.
The menu will disappear after a few seconds.
TV Operation
Power turns the TV on and off.
Channel Up/Down tunes to next channel.
Volume Up/Down adjusts sound level.
Captions turns selected Caption/Text option on and off.
Camport: Front Audio/Video Inputs
Video Input
L-Audio-R Inputs Note: TV sound is always monaural. Left/Right Audio input is processed into monaural sound by the TV.
5
adjust select menu
captions volume channel power
L audio R
video in
1
3
2
Typical Front Panel Controls
A
C
B
D
F
E
A
B
C
D
E
F
PAGE 13
206-3683
Guest Remote Key Functions
TIMER ALARM
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
CC
FLASHBK (FLASHBACK)
Returns to the last channel viewed.
POWER
Turns TV On or Off
.
CHANNEL (UP/DOWN)
Scrolls through available channels, and the Video Channel (Audio/Video source).
MUTE
Turns sound Off and On, while the picture remains.
ENTER
Press to view the Channel/Time
display or to remove any on-screen
display or menu.
NUMBER KEYPAD
Selects channels directly: enter channel numbers and press ENTER to go to new channel
.
remote control part number
SC652A
124-213-02A
TIMER
Press repeatedly to choose a TV
turn-off time, up to 4-hours.
Use to pick AM/PM in the Alarm menu.
VOLUME LEFT/RIGHT
Adjusts the sound level.
CHANNEL PREVIEW
Displays the available TV channels, includ­ing access to guest’s Parental Control menu. Allows guest to select the Aux Channel. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.)
CC (CLOSED CAPTIONING)
Press to access closed captions.
Press ENTER to exit.
A brief overview of the keys on the guest remote and what they do
ALARM
Press to display menu, then follow on­screen instructions to set a TV turn-on time.
PAGE 14
206-3490-O
Installer Remote Key Functions
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
MENU
ALARM
ADJ
ADJ
SELECT
FLASHBK (FLASHBACK)
Returns to the last channel viewed.
POWER
Turns TV On or Off
.
CHANNEL (UP/DOWN)
Flips through available channels.
MUTE
Turns sound Off and On, while the picture remains.
ENTER
Press to view the Channel/Time display or to remove any on-screen display or menu.
NUMBER KEYPAD
Selects channels directly and enters numeric values for some options
.
remote control part number
LP702
124-213-04
TIMER
Press repeatedly to choose a TV
turn-off time, up to 4-hours.
Use to pick AM/PM in the Clock/Alarm
menus, on some TVs.
VOLUME LEFT/RIGHT
Adjusts the sound levels.
CC (CLOSED CAPTIONING)
Press to access closed captions.
Press ENTER to exit.
An overview of the keys on the LP702 installer’s remote and what they do
ALARM
Press to go to the Alarm menu. Set a time for the TV to turn itself on.
MENU/SELECT/ADJ (ADJUST)
Press MENU repeatedly to scroll through
either the Installer, or User menus. Use
SELECT to choose an option and ADJ
(adjust) to change the selected option.
CHANNEL PREVIEW
Gives installer access to the guest’s menus. Displays the available TV chan­nels and hotel guest’s Parental Control menu. Allows user to select the Aux Channel. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.)
TV/FM
Selects TV or Radio on TVs equipped with
FM radio.
Loading...
+ 30 hidden pages