Zenith H20C50DT OPERATING GUIDE

Download

Page 1

machine number H20C50DT HealthViewTMTV

enjoy the view

installation & operating guide / warranty

table of contents

page

Page 2

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

This product is equipped with a 3-wire grounding-type alternating current line plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the three-wire ground type plug.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product.

WARNING

RISK OF ELECTRIC SHOCK DO NOT OPEN

3-WIRE COMM-WARN B-3/99

HealthViewTMis a trademark of Zenith Electronics Corporation

RECORD YOUR MODEL NUMBER

The model and serial number of the HealthViewTMTV are located on the back of the TV cabinet. For your future convenience, we suggest that you record these numbers here:

MODEL NO.____________________________________ SERIAL NO.____________________________________

Page 3

PAGE 3

206-3489-O

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

7. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Line-Cord Polarization

This product is equipped with a 3-wire grounding type alternating-current line plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the three-wire ground-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this installation and operating guide can help you get many years of enjoyment and safe operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

(Continued on next page)

PORTABLE CART WARNING

IMPORTANT SAFETY INSTRUCTIONS

Page 4

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the

product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been damaged.

f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

PAGE 4

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Ground Clamps Power Service Grounding

Electrode System (NEC Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical Code Instructions

NEC - National Electrical Code

206-3491-O

IMPORTANT SAFETY INSTRUCTIONS

Page 5

PAGE 5

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Information . . . . . . . . . . . . . . . . . . 3

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1. Hook Up the HealthView

TV and other Equipment Hookups

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Cable Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cable service with VCR . . . . . . . . . . . . . . . . . . . . . . . 9

Pillow Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Step 2. Channel Search and Reception Setup

Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

(Select Antenna, or cable service then perform channel search)

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 12

Installer’s Remote Key Functions . . . . . . . . . . . . . . . . 13

On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . 14

Step 3. Customize the TV’s Features

Setup Menu (Start with page 11, Auto Program)

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Captions (Caption/Text) . . . . . . . . . . . . . . . . . . . . . 18

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

FM Radio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Installer Parental Control Menu . . . . . . . . . . . . . . . 22

Other Menus and On-Screen Displays . . . . . . . . . . . . 24

Managing the Channel Banks . . . . . . . . . . . . 25 - 26 - 27

Installer Menus . . . . . . . . . . . . . . . . . . . . 28 - 29 - 30

LT2000 Quickset II Clone Programmer . . . . . . 31 - 32 - 33

Patient Operation Section (Copy for patient usage)

Patient Remote Control Key Functions . . . . . . . . . . . . 34

Patient Remote Control Key Functions - FM Radio . . . . . 35

Patient Parental Control Menu . . . . . . . . . . . . . . 36 - 37

Patient Menus and On-Screen Displays . . . . . . . . . . . . 38

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 - 43

Warranty for HealthView Series TVs . . . . . . . . .Back Cover

Purchase the Optional Installer’s Remote and Clone Programmer

To perform a normal installation set up, you need an installer’s remote such as the HP602, and the LT2000 Quickset II Clone Programmer—both are shown and described in later sections. The installer remote allows access to the Installer menus, User menus, and Source/Channel Bank keys. The installer remote has Menu, Select, and Adjust, and Channel Bank Keys. The LT2000 Quickset II Clone Programmer is used to duplicate a TV’s setup and install it on another identical TV. See your Zenith Dealer.

Design and specifications subject to change without prior notice.

Installer/Hospital Note:

Pages 34, 35, 36, 37, and 38 contain information and menus which the patient can use to operate the TV. It is recommended that these four pages be copied and included with the literature packet that the hospital provides to the patient.

206-3491-O

HealthViewTMis a trademark of Zenith Electronics Corporation

Page 6

PAGE 6

206-3491-O

Mini glossary

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire

sticking through the middle, and it screws onto the threaded jack on the back of the TV. A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws

on one end and a round opening with a wire sticking out on the other end.

Hook Up The Antenna to the TV

Connect an off-air antenna to the HealthView TV

If you have a 75 ohm RF cable, then you don’t need any adapters.

A 300 to 75 ohm adapter is not included with the Zenith HealthView TV.

300 TO 75 OHM ADAPTER

ANTENNA

CABLE

M.P.I.

TV back

Flat wire (300 ohm)

Antenna

300/75 ohm Adapter

TV back panel (expanded view)

PILLOW SPEAKER

SPKR

PILLOW

SPKR

TV back

TV back panel (expanded view)

ANTENNA

CABLE

M.P.I.

RF coaxial wire (75ohm)

Antenna

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Locate the Antenna/Cable jack on the back of the HealthView TV.

Connect the cable that runs from the wall directly to this jack, according to the diagram to the right.

Remove the back of the remote and put in two AA batteries.

Plug in the TV. Do not plug it into a switched outlet. the HealthView TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC Current.

Go to page 11 to Auto Program the TV.

back of

remote

1 2

Page 7

PAGE 7

206-3491-O

Hook Up The Cable (CATV) to the TV

If you’re using a cable box, leave the TV on channel 3 or 4 and use the cable box to change channels.

If you’re using a cable box, Auto Program might only find the channel the cable service is on (usually channel 3 or 4).

Cable TV wall jack

RF coaxial wire (75ohm)

TV back

ANTENNA

CABLE

M.P.I.

PILLOW SPEAKER

SPKR

PILLOW

SPKR

ANTENNA

CABLE

M.P.I.

Cable TV wall jack

Cable box

Out

RF coaxial wire (75ohm)

3 4

output switch

TV back

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Locate the Antenna/Cable jack on the back of the HealthView TV.

Connect the cable that runs from the wall directly to this jack, according to the diagram to the right.

Remove the back of the remote and put in two AA batteries.

Plug in the TV. Do not plug it into a switched outlet. Your HealthView TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC Current.

Go to page 11 to Auto Program the TV.

back of

remote

1 2

Connect cable service to the HealthView TV

Page 8

PAGE 8

206-3491-O

Hook Up Antenna and VCR to the TV

Connect the off-air antenna and VCR to the HealthView TV

No A/V cables are included with the Zenith HealthView TV.

TV back

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output switch

ANTENNA

CABLE

M.P.I.

TV back panel (expanded view)

TV back

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Flat wire (300 ohm)

Antenna

300/75 ohm Adapter

TV back

RF coaxial wire (75ohm)

not included with TV

RF coaxial wire (75ohm)

Antenna

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output switch

ANTENNA

CABLE

M.P.I.

TV back panel (expanded view)

TV back

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Locate the Antenna/Cable jack on the back of the VCR. Connect the cable that runs from the antenna directly to

this jack, according to the diagram to the right. Remove the back of the remote and put in two

AA batteries.

Plug in the TV. Do not plug it into a switched outlet. The HealthView TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC Current.

Go to page 11 to Auto Program the TV.

back of

remote

1 2

Page 9

PAGE 9

206-3491-O

Hook Up Cable Service (CATV) and VCR

Connect a VCR and Cable service to the HealthView TV

Leave the VCR and the television tuned to channel three or four and use the cable box to change channels.

Cable TV wall jack

Round wire (75ohm)

Cable box

Out

3 4

output

switch

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

ANTENNA

CABLE

M.P.I.

TV back panel (expanded view)

TV back

PILLOW SPEAKER

SPKR

PILLOW

SPKR

TV back

Cable TV wall jack

Round wire (75ohm)

A/V cables

not included

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

ANTENNA

CABLE

M.P.I.

TV back panel (expanded view)

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Locate the Antenna/Cable jack on the back of the VCR.

Connect the cable that runs from the wall jack directly to this jack, according to the diagram to the right.

Remove the back of the remote and put in two AA batteries.

Plug in the TV. Do not plug it into a switched outlet. The HealthView TV is designed to operate on standard current, 120-volt 60 Hertz AC. Do not attempt to operate it on DC Current.

Go to page 11 to Auto Program the TV.

back of

remote

1 2

Page 10

PAGE 10

206-3491-O

Pillow Speaker Hook Up

Locate the Pillow Speaker Output jack on the back of the HealthView TV.

Connect an accessory pillow speaker or wired remote control unit to this 6-pin jack.

Select PILLOW SPKR on the rear panel of the HealthView TV.

Use a pillow speaker by Curbell, Model A-16455-02 or other UL recognized pendant control bearing the warning: “Risk of fire if used in oxygen enriched atmos-

phere. Keep pendant control away from oxygen equipment.”

M.P.I.

ANTENNA

CABLE

TV back

TV back panel (expanded view)

PILLOW SPEAKER

SPKR

PILLOW

SPKR

1 2

Connect a pillow speaker to the HealthView TV

TV ON/OFF

CHAN DOWN

CHAN UP

(MALE PLUG)

VOLUME CONTROL

SPKR.

TV ON/OFF

OPEN

CHAN UP/DATA IN

COMMON

AUDIO OUT

CHAN DOWN

Controlling the TV with mechanical switches

Pin 4 (common) is momentarily connected to pin 1, 3, or 6 via push-action switches to control On/Off and Channel Up/Down. These pins are at +13 volts DC (when measured from pin 4) with the switches open. Current draw is 8 mA when a switch is closed. (This operation is identical to previous Zenith models using the 5-Wire Interface except that only +7 volts DC was supplied and current draw was only 2.5 mA.)

Pillow Speaker Interface

This connector furnishes three control lines and an audio output. A patient-pendant remote control, or entertainment audio and nurse call system may be connected here. All lines are isolated from the AC power line and earth ground. (Opto-isolators isolate the control lines, and a transformer isolates the audio. There are no relays or inductive components in the control lines.)

Pin no. Purpose

1 External TV On/Off switch 2 (not used) 3 External Channel Up switch or Data in 4 Common connection for control, data,

and audio output. Impedance to earth ground is a 10-meg resistor in parallel with a 1100 pf capacitor.

5 Isolated audio output. Nominal 14-ohm source

impedance with short circuit protection. Intended for a pillow speaker with a low-impedance pad-type volume control.

6 External Channel Down switch

Pillow speaker not included with HealthView TV.

Controlling the TV with Serial Data

The TV is capable of being controlled by a single wire, serial data signal. This is a Zenith patented technology and is being implemented by certain brands of “smart” pillow speakers, such as Curbell’s “GEN-II” models.

Page 11

PAGE 11

206-3491-O

Auto Program (Channel Search)

Use Auto Program to specify Antenna or cable service incoming signal source and automatically store all of the channels that are found by channel search

With the Installer remote control in hand, press the POWER key to turn on the HealthView TV.

Press the MENU key so the Setup menu appears. Using SELECT on the remote control, highlight Auto

Program on the screen. Press a Right or Left ADJ (Adjust) arrow to reach the

Auto Program menu. Using SELECT, choose either Cable TV or Off Air Antenna

on the screen. Press a Right or Left ADJ arrow to begin the Channel

Search. Press ENTER when the channel search is complete.

3 4 5

6 7

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

3/5

Mini glossary

OFF AIR ANTENNA If the patient can only view over-the-air broadcasts, select Antenna. CABLE If you provide cable service to the patients, select Cable.

Auto Program finds channels being received by the TV tuner. Cable will not work unless the hospital provides a cable service.

4/6

7 2

Page 12

PAGE 12

206-3491-O

Front Panel Controls

power

channel

volume

captions

Press the POWER button to turn on the HealthView TV.

Press the CHANNEL button to cycle through available channels.

Press the VOLUME button to adjust the sound level of the HealthView TV.

Press CAPTIONS to turn selected captions option on or off. (See Captions page.)

Using the front control panel to control the television

Page 13

PAGE 13

206-3584-O

Installer Remote Key Functions

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

FLASHBK (FLASHBACK)

Return to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Flip through available channels.

MUTE

Turns sound Off and On, while the picture remains.

ENTER

Press to view the Channel/Time display or to remove any on-screen display or menu.

NUMBER KEYPAD

Selects channels directly and enters numeric values for some options

remote control part number

HP602

124-213-06

TIMER

Press repeatedly to adjust TV turn-off time

up to 4-hours.

Use to pick AM/PM in Clock menu.

VOLUME LEFT/RIGHT

Adjusts the sound levels.

CC (CLOSED CAPTIONING)

Press to access closed captions.

Press ENTER to exit.

A quick list of the keys on the HP602 installer’s remote and what they do

BANK

Press and repeat to select a Channel Memory Bank - - 1, 2, 3, or 4 (standby).

MENU/SELECT/ADJ (ADJUST)

Press MENU repeatedly to scroll through

either the Installer, or User menus. Use

SELECT to choose an option and ADJ

(adjust) to change the selected option.

CHANNEL PREVIEW

Gives installer access to the patient’s menus. Displays the available TV channels and hotel patient’s Parental Control menu. Allows user to select the Aux Channel. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.)

TV/FM

Selects TV or Radio on TVs equipped with

FM radio.

BED 1/BED 2 (*See Note Below)

Determines the code set transmitted, Bed 1 or Bed 2. Switch setting must correspond to item 13, HOSPITAL MODE setting in the TV’s Installer Menu.

*Note: Bed 1 - Bed 2 switch on installer/patient remote. The position of the Bed 1 - Bed 2 switch must correspond to the setting in the Installer’s menu. The switch above can be set by sliding it to the Bed 1 or Bed 2 positon. On the patients remote, the Bed 1 or Bed 2 position can be selected by using a paper clip or a ball-point pen to slide the switch to the correct positon. Left position = Bed 1. Right Position = Bed 2.

Page 14

PAGE 14

206-3491-O

On-Screen Menus Overview

ON-SCREEN MENUS

Setup Menu Adjusts the basic characteristics of the TV Auto Program 11 Automatically finds and stores active channels to scroll through using Channel Up/Down. Add/Del/Blnk 15 Manually choose which active channels will appear when using Channel Up/Down.

Channel Labels 16 Labels the channels with their network names (ABC, CBS, HBO, etc.) or create custom names.

Clock Set 18 Sets the time.

Captions 19 Chooses the captioning or text option.

Language 20 Chooses the language the on-screen menus will appear in.

Video Menu 21 Adjusts the picture appearance. The options are: Contrast, Brightness, Color, Tint, Sharpness,

Picture Pref.

FM Radio Menu

22 Adjusts the FM Radio options.

Parental Control 23 Allows installer to block any channel or A/V source for up to 99 hours, with the use of a pass

word.

25 OTHER MENUS AND ON-SCREEN DISPLAYS

Channel/Time Shows the current time, channel, video and type of incoming audio signal.

Sleep Timer Sets the time the TV will turn off.

Volume Shows current sound level.

Captions Sets Caption/Text options.

Ch Preview Displays the available channels list.

Channel Bank Shows currently selected channel bank.

INSTALLER MENUS 28

Descriptions of the menus on the TV

Using the Menu button on the installer’s remote, the installer can access all the menus below.

Menu Name Page Description

Page 15

PAGE 15

206-3491-O

Fine-tune the patient’s channel selection list

Setting Add/Delete/Blank

Press the MENU key on the Installer’s remote so the Setup menu appears.

Press SELECT repeatedly to highlight the Add/Del/Blnk option.

Using either the NUMBER keypad and ENTER or the Channel Up/Down arrows on the remote, select a channel. (If adding a deleted channel, you will need to use the number pad and ENTER.)

Using the Right/Left ADJ arrows, choose whether that channel is Added, Deleted, or Blank.

To continue, select another channel and repeat Step 3. When you are finished, press ENTER to remove menu.

Adding Aux, VCR 3, VCR 4, or FM to the Channel Preview List

Go to the Setup menu, select the Add/Del/Blnk option. Use Channel Up/Down to select the option and choose Added. Note: If the option was turned off in the Service menu, you will have to reinstate it before it can appear as an option in the Channel Preview list.

Notes: Adding VCR 3 and/or VCR 4 as available channels forces TV Channel 3 and/or 4 to be retained, when running Auto Program, even though the equipment connected to the Antenna/Cable (RF) jack (like a cable converter and/or VCR) may be turned off. You can elect to Add, Delete or Blank: VCR 3, VCR 4, and Aux. FM can be Added or Deleted, but not Blanked.

1 2

4 5

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

CH 44 ADDED

Mini glossary

ADD Adds new channels to the list that the patient can scroll through when using the remote. DELETE Removes channels for one reason or another from the list that the patient can scroll through. BLANK Removes the video signal from a channel so the patient will only receive the audio signal.

3/5

If you delete a channel, it isn’t gone for good. Just select it using the NUMBER keypad on the remote, or add it later.

Page 16

PAGE 16

206-3491-O

Setting Up Channel Labels

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

A & E

Overview

Channel Labels help the user identify the channel or network being viewed. In the Setup menu with the CH LABELS option highlighted, use the Adjust

Left/Right arrows to scroll through the available channel labels, such as, A & E, AMC, ESPN, HBO, etc. These are a series of alphabetically organized preset labels from which you can choose the more common networks. Use any of these or create custom labels.

- - - - , The 4 dashes will allow a channel label to appear; if one is provided by XDS. (Extended Data Service)

NONE, prevents any channel label from appearing. LAB 1, thru LAB 20, are the 20 programmable labels.

The 20 programmable labels can be customized for your needs. Each programmable label has 5 characters spaces available.

To Program a Channel Label

First select a channel using the NUMBER keypad and ENTER or the Channel Up/Down arrows, on the Installer’s remote control.

(To select a deleted channel, use the NUMBER keypad and ENTER.) To program a channel label, go to the Setup menu and select CH LABELS. Press the Right/Left adjust arrow to scroll the available preset labels. Scroll

past - - - -, scroll past NONE, to go to the first programmable label slot, LAB

1. Notice that the label appears with the title LAB 1, and is also on a dark background; which will distinguish it from the preset labels.

Operating the Menu

Use Volume Up/Down to select the first letter. Press MUTE to clear the label if necessary. Use Channel Up/Down to change the character to one of the 255 characters

available.

Adjust Left/Right Switches to the next label.

- - moves to the next or previous label.

Volume Up/Down Selects character spaces

- - moves to the next or previous character space.

Channel Up/Down Scrolls through the available

characters.

ENTER Accept the channel label and

removes the menu.

MUTE Removes current label,

- - if first character space is selected.

Page 17

PAGE 17

206-3491-O

The Sleep Timer may be instantly set by pressing the TIMER key repeatedly. When you have made the selection, press ENTER to set the timer and return to TV viewing.

The clock can also be set using 24 hour “military time.” For p.m. settings add 1200. For example, to set 6:30 p.m., add 1200 to 630, = enter 1830.

Clock Set

Set the clock on the HealthView TV

1 2

3 4

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

11:44 PM

Highlight the Clock Set option. Set the current time; use the Number keypad to enter the

hours, then minutes. For example, enter 06, then 30, to set 6:30 on the clock.

Use the TIMER key to specify AM or PM. Press ENTER to start the clock and return to TV viewing.

Mini glossary

TIME A four-digit figure broken down into hours and minutes. HOURS First two digits that are entered when setting the clock, or the on/off timer. MINUTES The last two digits that are entered when setting the clock, or the on/off timer.

Page 18

PAGE 18

206-3584

Standard closed captioning is available using the Caption 1 option.

Captions (Captions/Text)

CAPTION 1 CAPTION 2 CAPTION 3 CAPTION 4

TEXT 1 TEXT 2 TEXT 3 TEXT 4

OFF

TO SET CAPTIONS

CAPTIONS SETUP

OPER. MODE SEL. TYPE CAPTION LOCK

PRESS SELECT TO CHOOSE PRESS ADJ TO CHANGE

STANDARD

ON, OFF

CAPTION 1 CAPTION 2 CAPTION 3 CAPTION 4

TEXT 1 TEXT 2 TEXT 3 TEXT 4

TO SET CAPTIONS

CAPTIONS SETUP

OPER. MODE SEL. TYPE CAPTION ON MUTE CAPTION LOCK

PRESS SELECT TO CHOOSE PRESS ADJ TO CHANGE

QUICK/MUTE

ON, OFF

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

Mini glossary

CAPTIONS The term for the words that scroll across the bottom of your TV screen; usually the audio portion of the program

provided for the hearing impaired.

TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages

provided by the broadcaste

Caption/Text is a feature which allows the HealthView TV to receive the closed caption and/or text options if made available by the broadcaster. Availability and functionality of Caption/Text features is determined only by each broadcaster and may not be available in your area.

Set up Closed Caption/Text options for the user

Closed Captions/Text Operating Modes Setup

Use MENU, SELECT, and ADJ Left/Right to choose the Closed Captions/Text mode and to set up the other menu options for the user.

Quick/Mute When CC is pressed: User can only turn Captions on/off.

(If CC on Mute is on, shows captions option on mute.) (If locked, type is retained with Power on/off.)

Standard When CC is pressed: User can choose a captions type.

(If locked, type is retained with Power on/off.)

Press ENTER repeatedly to remove menus.

Page 19

PAGE 19

206-3491-O

Language

ENGLISH

123

456

708

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

Choose the language for the on-screen menus

Press the MENU key on the remote control so the Setup menu appears.

Use the SELECT key on the remote control, to highlight Language on the screen.

Press a Right/Left ADJ arrow to choose one of the following options: English, Spanish or French.

Press ENTER to return to TV viewing.

2 3 4

Page 20

PAGE 20

206-3491-O

Video Menu

Press the MENU key repeatedly until the Video menu appears. Your options are:

• Contrast: Adjusts the level of difference between white and black in the TV picture. The more contrast, the brighter the picture appears.

• Brightness: Increases or decreases amount of white in the TV picture.

• Color: Adjusts levels of all colors in the TV picture.

• Tint: Balances between amounts of red and green in the

TV picture.

• Sharpness: Raises or lowers the definition of the TV picture. The lower the level, the softer the images will appear.

• Picture Preference: Choose either Custom or Preset. Custom allows you to set the picture the way you want. Preset moves all the above options back to their original, factory-set levels.

Using SELECT on the installer’s remote control, choose Contrast on the screen.

Using a Right/Left ADJ arrow, change the contrast level to your preference.

Press ENTER, or MENU one more time to return to TV viewing, or repeat from step two to set the other menu options.

Use SELECT to choose Picture Preference on the screen. Use the Right/Left ADJ arrows, to choose either the origi-

nal settings with Preset, or use your own settings with Custom.

2 3 4 5

Choose the Preset option in Picture Preference to quickly reset the levels to their original values.

Use the Video menu to customize the picture

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

2/5

3/6

Page 21

PAGE 21

206-3491-O

FM Radio Menu

Press TV/FM and choose the FM Radio operating mode. Press the MENU key repeatedly until the FM Setup Menu

appears. Your options are:

• Auto Program: In FM Mode, finds the available FM stations and puts them on the MUSIC ID list. You can select a station from this list with CHANNEL Up/Down.

• FM ADD/DEL: ADD or DEL (delete) a station in the MUSIC ID list. Stations on this list can be selected with CHANNEL Up/Down. Press ADJ (adjust) Left/Right to select ADD or DEL. Select the applicable station with CHANNEL Up/Down or Numbers, then press ENTER if you used Numbers. ADD Adds station to the MUSIC ID List. DEL deletes station from the MUSIC ID list

• FM Labels: Lets you label the stations on the MUSIC ID list. Labels include CLAS-Classical, COUN-Country, NEWSNews, OLDI-Oldies, OTHE-Other, RELI-Religious, ROCKRock, SPOR-Sports, TALK-talk

• Clock Set: Set the clock in this menu with the numbers. Press TIMER to change AM/PM, followed by ENTER to clear the screen.

Use SELECT to choose which option you wish to set up. Use ADJ Left/Right to set those options.

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

FM SETUP MENU

AUTO PROGRAM FM ADD/DEL FM. LABELS CLOCK SET

TO PROGRAM

88.1 ADDED

88.1 JAZZ 3:42 PM

TIMER

Use the FM Menu to customize FM Radio options

3 4

Page 22

Installer Parental Control Menu

Overview

To insure complete coverage for all TV programs, (movies and regular TV shows) choose a rating for MPAA, from the selections below AND choose ratings from the TV Parental Guidelines Rating System on the next page, using the Age Block option for General Audiences, and for Children. In addition to those, you may wish to add additional restrictions from the Content Block menu. See the Parental Control menu, and submenus example on the next page.

Things to Consider before Setting Up Parental Control

Determine which rating you consider acceptable to the viewer. (For example, if you choose TV-PG, all more restrictive ratings will be automatically blocked; the viewer will not be able to see: TV-PG, TV-14, or TV-MA rated programming.)

Do you want to block the auxiliary video source entirely? (Blocks the signal sent by the equipment, such as a VCR, connected to the TV Audio/Video input jacks; in the Aux. Block option.) Or leave unblocked, then choose allowable ratings.

Block program “Content” based on individual parameters such as: Strong Dialog, Mature Language, Sex Scenes, Violence Scenes, or Fantasy Violence Scenes; in the Content Blk option.

How many hours do you want Parental Control to be active? You can set the Hours option for up to 12 hours. Select a secret password; in the Set Password option. Use the number keys on the remote. Don’t forget the password, it is

the only way you can access the Parental Control menu and change rating selections, or turn Parental Control off. Do you want Parental Control to be active all the time? If not, you can turn it on or off; with the Lock On/Off option.

If used, this optional feature can “block” undesirable programming from appearing on the TV

You can set different Parental Control viewing restrictions for general audiences and for children - - both can be active at the same time

Simply specifying one content block such as Sex Scenes, will not automatically block another content in the programs from appearing.

If you choose to have the Aux inputs blocked, the ratings you specify will automatically restrict the programming that appears from the video sources.

You cannot disable Parental Control by disconnecting the TV from power. Block hours will automatically reset to the original block time setting specified if power is disconnected.

Parental Control offers the user a wide variety of options and settings that restrict or “block” the programming that can appear on the TV. Parental control allows the user the capability of defining which program rating they consider acceptable, to the younger or more sensitive viewer. It can be preset and turned either on or off by the user who specifies the secret 4-number code, the password. The number of hours blocked are specified. General audience and children viewer blocks can both be programmed into the TV’s memory. Viewer ratings are specified for both TV and the motion picture industry; both rating systems can be used. The ratings are based mainly on the ages of children.

PAGE 22

206-3491-O

Note

Reset Parental Control Block Hours to Zero and Cancel Password

This provides the institution staff and the installer a means to reset the TV to normal operation, if a guest has either forgotten the password or has left Parental Control Block active after checking out.

On the installer’s remote control, press and hold down MENU until the menu disappears (about 6 seconds). Immediately press 9, 8, 7, 6 and then CC. This will reset the Block Hours to Zero and cancel the current 4-number password.

Page 23

PAGE 23

206-3491-O

Installer Parental Control Menu

After you have read the preceding page, follow instructions below to set up and activate Parental Control

DIALOG LANGUAGE SEX SCENES VIOLENCE F VIOLENCE NO RATING

TO BLOCK

GENERAL CHILDREN

AGE BLOCK

UNBLOCKED

CONTENT BLOCK

AUX SOURCES MPAA RATING AGE BLK CONTENT BLK SET HOURS SET PASSWORD LOCK ON OFF

PRESS TO RETURN

123

456

708

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

1 2

Note: Use the installer’s remote control to specify Parental Control settings.

Press MENU repeatedly until the Parental Control Menu appears. With the Parental Control menu on-screen, use the SELECT button to

access the MPAA Rating menu and customize the level of restriction. Use the Left/Right ADJ arrow to adjust or set the rating for an

option, for example, use the “PG” setting. (See the Mini Glossary, Ratings Charts on pages 36 and 37 for rating descriptions.)

After you have selected and adjusted the parental control menu options to your preferences:

- Set the number of hours Advanced TV Control will be on.

- Set a 4-number password.

- Set the Lock On/Off option to either on or off. Note: Some broadcasts do not include rating information.

Notes

Reset the Maximum Number of Parental Control Default Block Hours

You can change the Block hours from the 12-hour default setting to up to 99 hours. In the Service Menu, item:

51 MAX BLK HRS 12,

use the Left/Right adjust arrow to set a different default number of hours.

To Turn the Parental Control Feature Off/On

In the Service Menu, item:

55 V-CHIP 0 or 1, use the Left/Right adjust arrow to set to 0, Parental Control menu will not appear. use the Left/Right adjust arrow to set to 1, Parental Control will be available.

Page 24

PAGE 24

206-3491-O

Other Menus & On-Screen Displays

CH 9 3:12

STEREO

Channel/Time/Audio Display

Press ENTER. Shows currently selected channel or source, current time if the clock has been set, and incoming audio signal.

Sleep Timer Menu

Press TIMER. Sets TV shut-off time and shows remaining time before TV shutoff.

Volume Display

Press VOLUME. Shows currently selected sound setting.

Ch Preview Menu

Press CH PREV. Displays list of the available TV Channels, Patient Parental Control menu and Video Channel access.

Closed Captions Display

Press CC. Shows if selected closed captions/text option is on or off.

VOLUME

Press the remote keys indicated below to access these menus and displays

Channel Banks Menu

Press BANKS. Gives access to the Channel Banks menus: Bank 1, Bank 2, Bank 3, Bank 4.

CHANNEL BANK

BANK 3

CAPTION 1 IS ON

CHANNEL PREVIEW 5 - - - 9 - - - 20 - - - 32 - - - 44 - - - AUX - - - FM

CC FOR PARENTAL CONTROL

CH TO SELECT, ENTER TO

INACTIVE TV

PLEASE . . .

CALL ATTENDANT

Inactive TV Display

Prompts patient to arrange for TV service to room.

Page 25

PAGE 25

206-3584

PLANNING THE CHANNEL BANKS

Generally, TV channels are grouped into “program packages” with terms that are proposed to the end user. The user then opts for a package. Below is an example of how TV channels may be grouped.

You may plan your package by using a chart like the one after the following page.

Remember, you can “blank” a channel for accommodating audio-only, such as an FM radio station or in-house communication.

Sometimes, only one or two channel banks may be needed. You may leave any unused bank with the channels entered during Auto Program; or, you may delete the channels. However, you may want to leave at least one channel in any unused bank. Then, if someone selects an “unused” bank, that channel will assure them that the TV is functional.

Note: Some channels from factory testing may be in the channel banks if you have not yet run Auto Program.

ADDING / DELETING CHANNELS

A previously prepared programming chart is helpful.

1. Run auto Program (in the Setup menu). The channels available in your cable/antenna will be entered in the channel banks 1, 2, 3, and 4. Note: Channels previously “blanked” will be cleared; channels entered that are not currently available, will be deleted.

2. Select a channel bank with an installer remote - -press SOURCE/BANK (and repeat). CHANNEL BANK and BANK number will be displayed.

3. Use the ADD/DEL/BLNK item (also in the Setup menu) to customize your program package. You may delete channels or add some that have not been entered. You can also “Blank” a channel for accommodating an audio-only program source or in-house communication. The “ADD/DEL/BLNK” item on page 15 has more details. Note: The Blank Channel feature is global. A channel will be blanked in all channel banks.

4. Repeat steps 2, and 3 to program another channel bank.

Managing the Channel Banks

The TV has four channel banks, where the administrator or installer can store groups of TV channels

Channel Bank Program package

1 Basic cable channels 2 Extended cable channels 3 Extended with premium channels 4 Other cable installer options

(Grouping is provided as an example only.)

The BLNK (blank) channel function is “global” -- the same channel number is blanked in channel banks 1, 2, 3, and 4.

Channel bank number display

Inactive TV Display (Channel Bank 4)

The TV can be set up to be inactive; which would require an attendant using an installer remote to change to a “billable” active channel bank selection Bank 1, 2, or 3, for institution control of patient-accessible programming. Channels in Bank 4 need to be removed for this purpose.

INACTIVE TV

PLEASE . . .

CALL ATTENDANT

CHANNEL BANK

BANK 1

Page 26

PAGE 26

206-3491-O

B Purpose Channel Number

A 12345678910111213141516171819202122232425

N K

1 A A A A AAAAAAA AAAA 2 A A A A AAAAAAA AAAA 3 A A A A AAAAAAA AAAA 4 A A A A AAAAAAA AAAA

B Purpose Channel Number A 12345678910111213141516171819202122232425 N K

1 Basic BC A AAAADDDDDDDD DDDD 2 Extend BC A AAAAADAADAAADDDD 3 All CTV BC A AAAAADAADAAAADAA 4 Other BC A AAAAAAAAAAAA AAAA

ADDING / DELETING CHANNELS

It is best to do ADD / DEL customizing before doing “BLNK.” AUTO PROGRAM enters the same channels in banks 1, 2, 3,

and 4. AUTO PROGRAM removes any channels previously customized

with ADD / DEL / BLNK. The channels available on your antenna / cable will be entered, and any channels previously entered but not currently available will be deleted.

ADD and DEL (not BLNK) can be used independently for channel banks 1, 2, 3, and 4.

A channel blanked, is blanked in all channel banks. Channel allocations in tuning bands: BROADCAST: 2 – 69

CABLE – CATV, HRC or ICC: 1 – 125

A = Active - - Channel was found during AUTO PROGRAM

A = Active Channel was found during AUTO PROGRAM D = Deleted Channel was deleted using Add/ Del option. BC = Blanked Channel Channel was blanked using BLANK channel option (ADD/DEL/BLNK).

Managing the Channel Banks

Examples of typical channel banks charts

Figure 1. Typical channel banks after running Auto Program

Figure 2. Typical channel banks after running Auto Program, and customizing with Add/Del/Blnk

Page 27

PAGE 27

206-3491-O

PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies)

B Purpose Channel Number A 12345678910111213141516171819202122232425 N K

1 2 3 4

B Purpose Channel Number A 26272829303132333435363738394041424344454647484950 N K

1 2 3 4

B Purpose Channel Number A 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 FM N K

1 2 3 4

B Purpose Channel Number A 51525354555657585960616263646566676869707172737475 N K

1 2 3 4

B Purpose Channel Number A 767778798081828384858687888990919293949596979899100 N K

1 2 3 4

Managing the Channel Banks

Page 28

PAGE 28

206-3584

Installer Menus

Installer should leave item 00 FACT MODE set to 0 and item 24 set to 1 (defaults).

Items 25-60 are installer-type adjustments and only qualified technicians having specialized test equipment should access them.

Item Description Range Fact. Set Recommend. Setting

00 FACT MENU 0 - 1 0 Leave default set 0 01 PRESET PX 0 - 1 1 02 PRESET AX 0 - 1 1 Leave default set 1 03 POWER MANAGE 0 - 7 0 04 VERT POS 0 - 25 15 05 HORZ POS 0 - 45 15 06 BAND/AFC 0 - 7 0 07 MIN VOLUME 0 - 63 0 08 MAX VOLUME 0 - 63 63 09 AC ON 0 - 1 0 10 KEY DEFEAT 0 - 1 1 11 STRT CHANNEL 0 - 255 255 12 STRT VOLUME 0 - 63, 255 255 13 HOSPITAL MODE 0 - 2 2 14 CHAN LOCK 0 - 1 0 15 GHOST CH. 0 - 1 0 16 SCAN MODE 0 - 1 1 17 TEXT MODE 0 - 1 1 18 SLEEP TIMER 0 - 1 1 19 ALARM 0 - 1 0 20 CH. OVER RIDE 0 - 1 1 21 OLD OCV 0 - 1 0 22 CAPTION LOCK 0 - 1 0 23 FUNCTION PRE 0 - 1 0 24 FEATURE LEVEL 0 - 1 1 Zen1/0 PLbl Leave default set 1 (1 Zen 1)

Use the Installer’s Menus to make TV operation adjustments

1480-00 1.03 01

03 POWER MANAGE 0

XX/XX/XX TE = 10110000

Accessing the Installer’s Menu

Installer’s menus can be accessed by using the installer’s remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. To exit the Installer’s Menu, press ENTER again. Any changes you make will be stored in nonvolatile memory.

The Installer’s Menu opens with item 03, POWER MANAGE. Press the SELECT key to sequence through the various items. Or, access an item directly by entering the line number, then pressing MENU. For example, to access the Start Channel option which is on line 11, press 11, then MENU. To change a current setting use the Left/Right ADJ keys.

Using the Installer’s Menu

Items 00-24 are immediately accessible only upon entering the Installer’s Menu. Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below. A second section of the Installer’s Menu that is intended for qualified service technicians only is not shown (items 25-60). Normally these items do not require adjustment.

Items in the Installer’s Menu:

Page 29

PAGE 29

206-3491-O

Installer Menus

00 FACT MENU (Factory Mode)

Used to access and customize the 00 - 24 Installer’s Menu settings using installer type remotes. Note: leave set to 0.

01 PRESET PX (Preset Picture)

Saves your custom video settings (color, tint, contrast, and brightness) in nonvolatile memory (not affected by power loss). Memory status is indicated by a 1 for “custom settings already stored,” or 0 for “custom settings have not been stored.”

Make all custom video settings before you access the Installer’s Menu and PRESET PX. When you use the ADJUST keys to toggle from 0 - 1, any changes in the video settings will be stored sure they are correct! These settings become the PRESET values for the PICTURE PREF option of the Video Menu. (For more information refer to the Video Menu section of this manual.)

02 PRESET AX

HealthView series TVs are equipped for monaural audio only. Since monaural operation is only mode available, leave default setting.

03 POWER MANAGE (Power Management)

The POWER MANAGE function is for saving energy. When set to 0, Power Manage is OFF. Settings range from 0 - 7, with 1 - 7 representing the hours that the TV will remain on, unless there has been activity from either the control panel or remote. One minute before turning off, the message “PRESS ANY KEY TO KEEP TV ON” appears.

04 VERT POS (Vertical Position)

Moves captions and displays vertically on the screen. Use the ADJUST keys. Typical value is 15. Black bars top and bottom define the active screen area.

05 HORZ POS (Horizontal Position)

Moves captions and displays horizontally on the screen. Use the ADJUST keys. Typical value is 15. Black bars top and bottom define the active screen area.

06 BAND/AFC (Band/Automatic Frequency Control)

There are 8 possible settings for this option:

0 = Broadcast Fixed 4 = Broadcast AFC 5 = CATV Fixed 1 = CATV AFC 6 = HRC Fixed 2 = HRC AFC 7 = ICC Fixed 3 = ICC AFC

Channels are accessed faster when fixed modes are used. The AFC (search modes) should only be used when some channels are not on nominal frequencies. NOTE: BAND is automatically set by AUTO PROGRAM.

If some channels were not found by AUTO PROGRAM, select the

appropriate AFC setting here and add the channels using the ADD/DEL option in the Setup Menu.

07 MIN VOLUME (Minimum Volume)

This function determines the minimum volume level allowable with the VOLUME (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The range is from 0 to 63—change values with ADJUST . The factory default is 0, which provides full range of volume control. It may be best to set the same value on every TV. NOTE: The minimum volume level cannot have a value setting higher than in the MAX VOLUME level (described below).

08 MAX VOLUME (Maximum Volume)

This function determines the maximum volume level allowable with the VOLUME VOL Up/Down control. In this way, for example, someone cannot set the volume level high enough to disturb others. The range is 0 to 63, with 63 as the default which gives the patient the full range of volume control. Change values with ADJUST keys. It may be best to set the same value on every TV. NOTE: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described above).

09 AC ON (AC Power Switchable)

Allows the TV to turn ON just by applying AC power. Pressing the ON button is not necessary. This is desirable when the TV is plugged into a cable box or a power outlet controlled by a wall switch. Use ADJUST to select 0 or 1, where 0 is the default is OFF, and 1 is ON.

NOTE: When set to 1 (ON), the TV does not respond to ON/OFF commands from either the remote or the control panel, and the SLEEP TIMER is also nonfunctional.

10 KEY DEFEAT (Keyboard Defeat)

When set to 1, it prevents the end user from accessing screen menus on the front panel—MENU, SELECT, and ADJUST do not function. When set to 0, those keys are functional. The menus can always be accessed with MENU on the remote. Note: HealthView TVs are not equipped with front panel menu and adjust keys.

11 STRT CHANNEL (Start Channel)

When active, this function allows you to determine the initial channel number when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that channel when it is turned on. Setting this to 255 causes the last channel viewed when TV was turned off to be the tuned to channel when the TV is turned on again.

The range of values is 0 - 255. Use (adjust) keys to choose numbers that determine the start channel.

Use the Installer’s Menus to make TV operation adjustments

Page 30

PAGE 30

206-3584

Installer Menus

12 STRT VOLUME (Start Volume)

When active, this function allows you to determine the initial volume level setting when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that channel when it is turned on. When inactive, the volume level and channel retain the settings when the set was last used.

The range of values is 0 - 63, 255. Use (adjust) keys to choose: (1) With number 255 the feature is inactive. (2) Other numbers determine the start channel. (3) Set the volume level as desired before exiting the installer menu.

13 HOSPITAL MODE (Leave set to 2)

0 is non-hospital mode. 1 enables hospital mode, bed 1, which makes the TV respond to Zenith Private Label IR codes. 2 (default setting) enables hospital mode, Bed 2 which makes the TV respond to Zenith IR codes.

14 CHAN LOCK (Channel Lock)

When set to 1 the CHAN LOCK is ideal if a cable box (or similar) is the sole source for programming—and the TV must always be on the same channel. Changing channels with the Channel up/down or or keypad numbers is impossible. Channel Lock is inactive when set to 0 (default).

Generally, this feature is used in connection with START CHAN/VOL (line 11) where the start channel may, for example, be set to 3 or

4. If the start channel is 3 then the TV will remain on channel 3. NOTE: When channel lock is active AUTO PROGRAM and CH. ADD/DEL in the SETUP MENU are not active.

15 GHOST CH. (Ghost Channel)

When set to 1, the current channel number is displayed in the upper right corner of the CRT. The number moves slightly to prevent damage to the screen. The default is “0” or OFF. NOTE: When captions are on, the “ghost channel” is not displayed.

16 SCAN MODE

Allows variation in setting the On/Off with Channel UP/DOWN. You may opt for TV channels only; TV channels + Off/ON; TV channels + FM radio; TV channels + FM radio + Off/On with these settings for Scan Mode:

Scan mode Characteristics

0 Channel up/down keys change channels only.

1 Channel down below the lowest channel (or

channel up higher than the highest) and TV turns off.

2 Channel down below the lowest channel (or up

higher than the highest) and TV goes to FM radio. Channel down below lowest FM station (or Channel up higher than the highest) and TV channels return

3 Channel down below the lowest channel (or up

higher than the highest) and TV goes to FM radio. Press channel down below lowest FM station (or Channel up higher than the highest) and TV turns off.

17 TEXT MODE

Determines whether TEXT 1, TEXT 2, TEXT 3, and TEXT 4 decoding is enabled when CAPTIONS are turned on (either from the Setup Menu or directly with CC on the remote). When set to 0, only Caption 1, Caption 2, Caption 3, and Caption 4 are accessible. When set to 1, Caption 1, 2, 3, 4 AND Text 1, 2, 3, 4 are accessible.

TIP: Set Text Mode to 1 only if text is offered in your video system.

18 SLEEP TIMER

When set to 1, a patient may use the SLEEP TIMER feature. When set to 0, the sleep timer is not available.

19 ALARM

Gives you the option of making the alarm function available to the end-user. Set to 1, alarm function is available. Set to 0 to withhold this function.

20 CH. OVER RIDE (Channel Override)

When set to 1, the user is allowed to select channels with either Channel up/down or by direct keypad entry. When set to 0, only those channels that are entered in the active channel bank may be selected.

21 OLD OCV (On Command Video)

Set to 1 for operation with systems from On Command Corporation.

22 CAPTION LOCK

Set to 1 to restore previous caption On/Off state after TV turns off when set to 0, captions are always off when TV is initially turned on.

23 FUNCTION PRE

Set to 0 to suppress channel prev function with some pay per view systems.

24 FEATURE LEVEL (Note: Leave set to 1 otherwise the TV cannot be operated unless a Zenith private label remote is used.)

Set to 1 for default Zenith IR Code recognition. Set to 0 for Zenith Private Label IR Code recognition.

Installer should leave item 24 FEATURE LEVEL set to 1 (default). Items 25-60 are service-type adjust-

ments and only qualified technicians having specialized test equipment should access them.

Use the Installer’s Menus to make TV operation adjustments

Page 31

PAGE 31

206-3491-O

LT2000 QuickSet Programmer

A slow flashing green light indicates there is a problem with the communications between the TV and the programmer. In this case, check for a damaged cable, poor contacts, or other connection troubles.

If the status indicator is red, the programmer batteries are low and should be replaced. Use 4 good-quality alkaline AA batteries.

Use the Zenith LT2000 QuickSet II “Clone” Programmer to copy the setup from a “master” TV then quickly transfer the setup to duplicate TVs must be the same model number as the master TV

The optional QuickSet II Clone Programmer (LT2000) allows custom setup and programming information to be quickly copied from a master TV into multiple identical television sets. Once learned from the master, setup data is retained in the LT2000 for future use.

When using the LT2000, cloning operations will go easier if the TV set is connected to a good quality signal and operating with a stable picture displayed. To operate the LT2000, use the indicated keys on an HP602, LP702, or MBR3447 remote, or the front panel keys on the TV receiver.

Before you begin:

• The “master TV” should be connected to a good, stable signal from an over-the-air antenna or cable service and turned on.

• Teaching and Learning is only possible between identical model Zenith TVs. (However, the Clone programmer can store 4 different master TV setups.)

WARNING: Copying a blank or incorrect memory into a TV will cause the TV to operate erratically or become inoperable.

• Use a Zenith MBR Remote like the MBR3447 or the TV front panel controls to operate Learning and Teaching menus.

• Make sure that the batteries in the Clone programmer are fresh.

• If the batteries are removed, the Clone Clock time will be lost.

• Decide if you want to set the time from the Clone programmer or copy the time to the Clone programmer; from a TV which has the clock set to the current time.

• TVs chassis series with the numbers 34, 35, and 50 included in their model numbers (model numbers are on the TV’s back) require an additional special procedure to set up Channel Labels. (See next page.)

• Follow the connection diagrams above to connect the Clone to a

master TV and, after learning is complete, to another TV to “teach” it the setup.

• Setting the time and transferring it to the Clone or another TV is a separate procedure.

• Once a TV’s setup is copied to another TV, that TV needs to be disconnected from power for about 5 seconds to activate the newly copied setup.

• See Troubleshooting to solve problems.

A. Set Up a Master TV

Using a Zenith Multi-Brand remote like the MBR3447, set up a “Master” TV with custom settings and features as described in the master TV’s operating guide. (If the TV Model number includes 34, 35, or 50, do not set up Channel Labels at this time.) The master TV’s Setup is what you will copy to the Clone Programmer and transfer to TVs of the same model so they will operate identically.

B. Connect Clone to Master TV

If there is a good connection, the “Clone has Control of TV” message will appear. (See menu above.)

Learn Master TV

Typical MPI Connections

Teach Other TV

Typical MPI Connections

Antenna

TV back

Antenna

TV back

THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION XX

THE TV IS VERSION XX THE SW IS REVISION XX

CLONE CLOCK = XX:XX TV CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

RF coaxial wire (75ohm)

AUDIO INPUT

ANTENNA

CABLE

M.P.I.

AUX

INPUT

QuickSet II Programmer

LT2000

Clone

COMPUTER

S-VIDEO INPUT

VIDEO

LOOP OUT - S-VHS - IN

R -AUDIO- L

RIGHT

R- AUDIO- L

LEFT

RF coaxial wire (75ohm)

COMPUTER

AUDIO INPUT

ANTENNA

CABLE

S-VIDEO

INPUT

M.P.I.

AUX

INPUT

QuickSet II Programmer

Clone

LOOP OUT - S-VHS - IN

VIDEO

LT2000

R -AUDIO- L

RIGHT

LEFT

R- AUDIO- L

Page 32

PAGE 32

206-3491-O

Clone Selection Menu Choices

Typical Edit Channel Labels on-screen menus

Editing Channel Label Number

Editing Channel Label Content

Editing Channel Number

C. Learn Setup from Master TV

Press 1 to select the “Learn From TV” option, then press ON/OFF, POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the Memory ”Bank” (1, 2, 3, or 4) you want to store this Master TV’s Setup in by pressing either Channel key repeatedly to pick Memory 1, 2, 3, or 4. (If you choose a Memory “Bank” that already has a master TV’s setup already in it, it will be overwritten by this Master TV’s setup.) Once the Clone memory bank is selected, press ON/OFF, POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master TV’s setup.

Ca. 34, 35, 50 Chassis Series TVs Special Edit Channel Labels Feature

Use the Clone’s EDIT CHANNEL LABELS option to create channel labels for the master TV. (It may be helpful to create a list of the available channels and write them down on paper. Alongside the channels numbers, write in your custom labels. See the Edit Channel Labels menus on the previous page. With the Clone Selection Menu on-screen, press 7, then ENTER to go to the Channel Labels Edit Menu. Edit the channel labels by following the on-screen instructions. When finished go back to the Clone Selection Menu and choose (8) SEND CHANNEL LABELS, then press ON/OFF, POWER, or ENTER. Pick the Clone memory bank where the channel labels will be stored. (Should be the same Clone memory bank 1, 2, 3, or 4 where you want to store the same TV setup.)

Cb. Set the Clock (Optional)

Set the time on the Master TV’s Clock. (If the time has already been copied from another TV into the Clone programmer, you can

set the Master TV’s clock by copying the time from the Clone programmer.) The Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries is for it to keep the time as accurately as possible.) Since the Clone Programmer’s time cannot be set directly, the time needs to be copied from a Zenith TV equipped with MPI input capability.

Once the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a Master TV, or another TV which has had the features already set up.)

D. Teach Master TV’s Setup to Other TV

Once Learning is complete, remove the MPI cable from the master TV and connect it to the TV that you want to copy the master TV’s setup to. With the “TV is Controlled by Clone” message displayed, press 2 or use either Channel key to go to the “Teach to TV” option, press ON/OFF, POWER, or ENTER. Follow on-screen instructions to transfer the Setup and other information to the “Learning” TV. After the “Teach to TV is Complete” message is displayed, press any key to return to the Clone menus option, then press ON/OFF, POWER, or ENTER. If finished, remove MPI cable from the TV.

E. Disconnect TV Power for 5 Seconds

Remove the TV power cord of the newly “Cloned TV” from the power outlet for about 5 seconds to activate the newly copied setup.

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX THE TV IS VERSION XX THE SW IS REVISION XX

CLONE CLOCK= XX:XX TV CLOCK= XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

EDIT CHANNEL LABELS FOR MEMORY 1

LABEL 1: WYC 1 FOR CHANNEL - - *EDITING LABEL CONTENT*

-VOL TO SELECT ITEM TO EDIT

-CH UP/DOWN CHANGE ITEM VALUE

-MUTE TO CLEAR THIS PROG. LABEL

-CC TO CLEAR ALL PROG. LABELS

-PRESS ENTER TO STORE THIS LABEL

-PRESS POWER OR ON/OFF WHEN DONE

CLONE SELECTION MENU (1) LEARN FROM TV

(2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAY TV SETUP (6) DISPLAY CLONE SETUP (7) EDIT CHANNEL LABELS (8) SEND CHANNEL LABELS

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER

EDIT CHANNEL LABELS FOR MEMORY 1

LABEL 1: WABC FOR CHANNEL 20 *EDITING CHANNEL NUMBER*

-VOL TO SELECT ITEM TO EDIT

-CH UP/DOWN CHANGE ITEM VALUE

-MUTE TO CLEAR THIS PROG. LABEL

-CC TO CLEAR ALL PROG. LABELS

-PRESS ENTER TO STORE THIS LABEL

-PRESS POWER OR ON/OFF WHEN DONE

SELECT CLONE MEMORY CONTAINING THE LABELS TO BE EDITED.

(1) CHANNEL LABELS FOR MEMORY 1 (2) CHANNEL LABELS FOR MEMORY 2 (3) CHANNEL LABELS FOR MEMORY 3 (4) CHANNEL LABELS FOR MEMORY 4 (5) RETURN TO CLONE MENU

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

CLONE SELECTION MENU

(1) LEARN FROM TV (2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAY TV SETUP (6) DISPLAY CLONE SETUP (7) EDIT CHANNEL LABELS (8) SEND CHANNEL LABELS

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER

EDIT CHANNEL LABELS FOR MEMORY 1

LABEL 1: LAB 1 FOR CHANNEL - - *EDITING LABEL NUMBER*

-VOL TO SELECT ITEM TO EDIT

-CH UP/DOWN CHANGE ITEM VALUE

-MUTE TO CLEAR THIS PROG. LABEL

-CC TO CLEAR ALL PROG. LABELS

-PRESS ENTER TO STORE THIS LABEL

-PRESS POWER OR ON/OFF WHEN DONE

SEND SELECTED CHANNEL LABEL MEMORY TO TV

(1) CHANNEL LABELS FOR MEMORY 1 (2) CHANNEL LABELS FOR MEMORY 2 (3) CHANNEL LABELS FOR MEMORY 3 (4) CHANNEL LABELS FOR MEMORY 4 (5) RETURN TO CLONE MENU

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

Page 33

PAGE 33

206-3491-O

Clone Selection Menu Choices

Operation Notes

Disconnect the Clone from the TV when you are finished; automatically switching it off. The real-time clock continues to run when the main circuits are switched off.

Reset Clone After Static Shock

After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, use a paper clip or similar instrument inserted through the small hole marked ”RESET” to activate the internal reset switch and restore normal operation. After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV containing the correct time.

The LT2000 programmer is designed to be used with TVs containing the 221-01006 and later processors. Use with earlier TV sets may give unpredictable results. The specific microprocessor used in any TV set may be determined by activating the Installer Menu. The microprocessor part number appears at the top of the screen when the Installer Menu is activated. Processors before the 221-01006-04 have a limited screen display capability. They can not display entire screens as shown in the quick setup instructions accompanying the LT2000 clone programmer. Use the printed menu illustrations on the quick setup sheet supplied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clone functions all operate normally.)

When cloning operations are complete, just unplug the LT2000 from the TV.

If the TV does not display a picture (blank screen) after a few seconds, just change channels.

Troubleshooting

Problem Possible Cause(s) Possible Solution(s) Clone Programmer

LED does not blink. • MPI cord not connected. -Connect MPI cord.

• TV not turned on. -TV must be on for clone to work.

• Weak batteries. -Install 4 fresh AA high-quality alkaline batteries.

Clone menu hard • Weak signal. -Connect TV to a reliable signal source. to read.

No time set. • No time on Master TV. -Set time on master TV, copy time to Clone Programmer.

Master and Other TVs

Cloning did not work. • Procedure interrupted. -Wait until procedure complete message is displayed.

• Different TV models. -Cloning is only possible with identical model TVs. Clone time disappeared. • Batteries were removed. -Batteries must remain installed to retain time settings. Channel Labels not • Saved to other memory. -Must save channel labels to same memory bank as

present on cloned TV. master TV setup. New Setup not present. • TV not reset. -Disconnect newly cloned TV from power for 5 seconds.

Page 34

PAGE 34

206-3491-O

Patient Remote Key Functions

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

TIMER

CH PREVIEW

FLASHBK (FLASHBACK)

Return to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Flip through available channels, and the Video Channel (Audio/Video source).

MUTE

Turns sound Off and On, while the picture remains.

ENTER

Press to view the

Channel/Time/Audio display or to

remove any on-screen

display or menu.

NUMBER KEYPAD

Select channels directly: enter channel numbers and press ENTER to go to new channel

remote control part number

SC637

124-213-02

TIMER

Press and repeat to use Sleep Timer.

VOLUME LEFT/RIGHT

Adjusts the sound levels.

CHANNEL PREVIEW

Displays the available TV channels and gives hospital patient access to the Parental Control menu. Allows patient to select the Video Channel. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.)

CC (CLOSED CAPTIONING)

Press to access closed captions.

Press ENTER to exit.

A quick list of the keys on the remote and what they do

TV/FM

Press for TV or FM radio.

Page 35

PAGE 35

206-3491-O

Patient Remote Key Functions-FM Radio

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

TIMER

CH PREVIEW

FLASHBK (FLASHBACK)

Returns to radio station previously selected.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Scrolls through available channels, and the Video Channel (Audio/Video source).

MUTE

Turns sound Off and On.

remote control part number

SC637

124-213-05

VOLUME (UP/DOWN)

Adjusts the sound levels.

A quick list of the keys on the patient remote and what they do

TIMER

Press and repeat to set the time

the TV will turn itself off.

TV/FM

Press for TV or FM radio mode.

ENTER

Press for MUSIC ID, list of available FM stations. (Press ENTER again or wait a few seconds for Station/Time display.)

Page 36

PAGE 36

206-3491-O

Parental Control Menu

Mini glossary

MOTION PICTURE ASSOCIATION OF AMERICA (MPAA) RATING SYSTEM

G General Audiences Content not offensive to most viewers. PG Parental Guidance Content is such that parents may not want their children to view the program.

Suggested

PG-13 Parental Guidance Program is inappropriate for preteens, with a greater degree of offensive material

Suggested than a PG rated program. R Restricted viewing Not for children under age 17. Strong elements of sex and/or violence. NC-17 Restricted Viewing Not for children under age 17 under any circumstances. Strong sexual content. X Hard Core Films Same as NC-17 rating.

Note: Zenith Electronics Corporation is not liable for any program content that appears when using this rating system; as always, user discretion is advised.

Overview

Things to Consider before Setting Up Parental Control

Block program “Content” based on individual parameters such as: Strong Dialog, Mature Language, Sex Scenes, Violence Scenes, or Fantasy Violence Scenes; in the Content Blk option.

This optional feature can be used to “block” undesirable programming from appearing on the TV

You can set different Parental Control viewing restrictions for general audiences and for children - - both can be active at the same time

Simply specifying one content block such as Sex Scenes, will not automatically block another content in the programs from appearing.

Even if you choose to leave the Aux inputs unblocked, the ratings you specify will automatically restrict the programming that appears from the video sources.

You cannot disable Parental Control by disconnecting the TV from power. Block hours will automatically reset to the original block time setting specified if power is disconnected.

This TV offers the user a wide variety of options and settings that restrict or “block” the programming that can appear on the TV. Parental Control allows the user the capability of defining which program rating they consider acceptable, to the younger or more sensitive viewer. It can be preset and turned either on or off by the user who specifies the secret 4-number code, the password. The number of hours blocked are specified. General audience and children viewer blocks can both be programmed into the TV’s memory. Viewer ratings are specified for both TV and the motion picture industry; both rating systems can be used. The ratings are based mainly on the ages of children.

Page 37

PAGE 37

206-3491-O

Parental Control Menu

Mini glossary

TV PARENTAL GUIDELINE RATING SYSTEM

TV-G General Audience Considered suitable for all audiences; children may watch unattended. TV-PG Parental Guidance Suggested Unsuitable for younger children, may contain: Suggestive Dialog, Mature Language, Sex, and Violence Scenes. TV-14 Parents Strongly Cautioned Unsuitable for children under 14, may contain: Strong Dialog, Mature Language, Sex, and Violence Scenes. TV-MA Mature Audience Only Adults only, may contain: Strong Dialog, Mature Language, Sex, and Violence Scenes.

CHILDREN’S CLASSIFICATIONS

TV-Y Children Considered suitable for all children under 7 years old. TV-Y7 Children 7 and over Considered suitable for children over 7, may contain Fantasy Violence Scenes.

Press CH PREVIEW. Press CC to access the PARENTAL CONTROL menu. Use SELECT to highlight an option like CONTENT BLOCK. Press ADJ Right arrow to go to the CONTENT BLOCK menu. Use SELECT to highlight an option like SEX SCENES. Press ADJ Right arrow to choose: Unblocked, TV-PG AND

ABOVE, TV-14 AND ABOVE, or TV-MA. (AND ABOVE means more restrictive headings are automatically included when you choose a low restriction setting like TV-PG.) See the Mini Glossary, Ratings Charts on this and the previous page for rating meanings.

After you have selected and adjusted the parental control menu options to your preferences:

- Set the number of hours Parental Control will be on.

- Set a 4-number password using the NUMBER keypad.

- Set the Lock On/Off option to either on or off.

Note: some broadcasts do not contain rating information.

After you have read the preceding page, follow instructions below to set up and activate Parental Control

TO BLOCK

CHANNEL PREVIEW 5 - - - 9 - - - 20 - - - 32 - - - 44 - - - AUX - - - FM

CONTENT BLOCK

DIALOG LANGUAGE SEX SCENES VIOLENCE F VIOLENCE NO RATING

TV-MA

CC FOR PARENTAL CONTROL

CH TO SELECT, ENTER TO QUIT

PRESS CC TO RETURN

123

456

708

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

3/5

4/6

1 2 3

5 6

Page 38

PAGE 38

206-3491-O

Menus & On-Screen Displays

CH 9 3:12

STEREO

Channel/Time/Audio Display

Press ENTER. Shows currently selected channel or source, current time if the clock has been set, and incoming audio signal.

Sleep Timer Menu

Press TIMER. Sets TV shut-off time and shows remaining time before TV shut-off.

Volume Display

Press VOLUME. Shows currently selected sound setting.

Ch Preview Menu

Press CH PREV. Displays list of the available TV Channels, Patient Parental Control menu and Video Channel access.

Closed Captions Menu

Press CC. Turns selected closed captions/text option on or off.

CHANNEL PREVIEW 5 - - - 9 - - - 20 - - - 32 - - - 44 - - - AUX - - - FM

CC FOR PARENTAL CONTROL

CH TO SELECT, ENTER TO

VOLUME

CAPTION 1 IS ON

Press the remote keys indicated below to access these menus and displays

Inactive TV Display

Notify nurse/attendant if you wish to use TV.

INACTIVE TV

PLEASE . . .

CALL ATTENDANT

Page 39

PAGE 39

206-3491-O

Routine TV cabinet and screen cleaning

Maintenance

1. Here’s a great way to keep the dust off the screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.

2. Make sure the excess water is off the screen, and then let it air-dry before turning it on.

1. Use a soft cloth with a mild soap solution to wipe the cabinet. (Avoid using any harsh, industrial strength variety of cleaner.)

2. Rinse the cloth and wipe the cabinet again.

3. Let the cabinet air-dry before turning the HealthView TV on.

Use a quality wood cleaner and polish. This will protect the TV from dirt and dust, as well as keep the cabinet looking new.

If you leave the TV dormant for a long time, it’s a good idea to unplug the power to protect against possible damage from lightning or power surges. If you use an off-air antenna, you may also want to disconnect it from the back of the TV before leaving.

Screen Cleaning

Extended Absence

Cabinet Cleaning

Wood Cabinet

Careful and regular cleaning can extend the the useful service life of the TV. Be sure to turn the power off and pull out the plug before you begin any cleaning.

Page 40

PAGE 40

206-3491-O

SYMPTOM

Snowy picture and unclear sound.

Multiple images or ‘ghost shadows.’

Interference: Sharp lines across the screen and lousy sound.

Normal picture but no sound.

No picture and unclear sound.

No picture and no sound.

No color, but the sound is O.K.

Picture has a big black box on it, but the sound is O.K.

Remote control doesn’t work.

Menu options can’t be changed or selected.

No picture or sound when any non-cable source is selected.

Troubleshooting

Some quick and easy tips to resolving problems

POSSIBLE SOLUTIONS

• Check the antenna connection or location.

• Check the cable input.

• Check to see if the TV/ VCR button on the VCR has the TV selected.

• Check the antenna direction and/or location.

• Check the cable input.

• Make sure the cable from the antenna to the TV is properly connected.

The following may cause image problems or distortion: Electrical appliances, powerful lights, cars, trucks; computers or portable phones; medical equipment.

• If possible increase the distance between the TV and the offending appliance. Or shut one of them off.

• Check volume levels.

• Make sure the TV is not Muted.

• Try another channel. The problem may be the broadcast, not the TV.

• Are the Audio A/V cables properly installed?

• Are the wires for external speakers (if you have external speakers) properly installed?

• Are you in TV or cable tuning mode, and should be in the other?

• Make sure output channels on all A/V equipment are on the same channel (3 or 4).

• Check that all connections are tight.

• Is the AC power plugged in?

• Check that the AC power outlet works. (Test it by plugging in something else or try another plug.)

• Make sure the brightness and audio controls are set properly.

• Try another channel. The problem may be with the broadcast.

• Check the color control in the Video menu.

• Try another channel. The problem may be with the broadcast.

• The CC (closed caption) option may be in Text mode. Select Caption 1, or OFF in the Captions/Text menu.

• Make sure the batteries are fresh and installed properly.

• Make sure the batteries are installeded properly (see page 6) with correct polarity.

• Try unplugging the TV for a few minutes, then plug it back in.

Page 41

PAGE 41

206-3584-O

Glossary

A list of definitions for some of the words found in this guide

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a

wire sticking through the middle. It screws onto the threaded jack on the back of the TV.

300 TO 75 OHM A small device that connects a two-wire

300 ohm antenna to a 75 ohm RF jack.

ADAPTER They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on

the other end.

A/V CABLES Audio/Video cables. Three cables bunched together—right audio (red), left audio (white), and video (yellow).

A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices.

A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television). ADD Adds new channels to list that the patient will scroll through when using the patient remote. AMPLIFIER An electronic device that amplifies sound from a television, CD player, VCR, DVD or other A/V device. ANTENNA The physical receiver of television signals sent over the air. A large metal piece of equipment does not always have

to be visible for your home to be using an antenna.

AUTO PROGRAM Auto Program has the HealthView TV automatically find all the channels available in your area. DELETE Lets you remove channels from the list the patient will scroll through using the patient remote. INPUT Refers to the jack that receives a signal from a TV, VCR or other A/V device. JACK A connection on the back of a TV, VCR, or any other A/V device. MONO SOUND Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio. OUTPUT Refers to the jack that sends a signal out of a VCR, DVD, or other A/V device. SIGNAL Picture and sound traveling through a cable, or over the air, to your television screen. TUNER Device that picks up the signal and turns them into picture and sound.

Page 42

PAGE 42

206-3491-O

Notes

Page 43

Notes

PAGE 43

206-3584-0

Page 44

Direct-View Color TV Welcome to the Zenith family! We believe that you will be pleased with your new Zenith HealthView TV. Please read this warranty carefully, it is a

“LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state within the U.S.A.

ZENITH’S RESPONSIBILITY

Service Labor During a period of one year from effective warranty date, Zenith will provide service labor by a Zenith authorized service center when needed, as

determined by the Zenith service center, as a result of manufacturing defects.

Parts New or remanufactured replacements for factory-defective parts will be supplied by a Zenith authorized service center for one year from effective

warranty date (color picture tube — two years). Such replacement parts are warranted for the remaining portion of the original warranty period.

In-Hospital Service Warranty service for 20” diagonal (U.S.A.) or larger screen size models is provided in the institution in most cases. (Some repairs may require

the unit to be taken by the servicer to the repair facility and returned, at no additional charge.)

Not Covered This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls, installation or repair of antenna systems,

cable converters or cable company-supplied equipment; it also does not cover damage due to misuse, abuse, negligence, acts of God or other causes beyond the control of Zenith. Any alteration of the product after manufacture voids this warranty in its entirety.

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ZENITH SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, TO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.

OWNER’S RESPONSIBILITY

Effective Warranty Date Warranty begins on the date of installation of Commercial Products Direct View Television Receiver. For your convenience, keep the dealer’s

dated bill of sale or delivery ticket as evidence of the purchase date.

Operating Guide Read your Operating Guide carefully so that you will understand the operation of the TV and how to adjust the controls.

Carry-In Service Models under 20” diagonal (U.S.A.) screen size must be taken to a Zenith authorized service center for warranty service and must be

picked up by the owner.

Antenna Reception problems caused by inadequate antenna or faulty antenna connections are the owner’s responsibility.

Important Product Registration—Please fill out and mail your Product Registration Card. It is imperative that Zenith know how to reach you promptly if we

should discover a safety problem that could affect you.

Warranty Service For warranty service information, contact any Zenith authorized service center. Parts and service labor that are Zenith’s responsibility (see above)

will be provided without charge. Other service is at the owner’s expense. If you have any problem in obtaining satisfactory warranty service, call or write the Zenith Response Center. You must provide the model number, serial number and date of purchase or date of original installation. Before you ask for warranty service, read “Maintenance and Troubleshooting” in the operating guide. You might avoid a service call.

Be sure to send in the Product Registration Card. We will send you an application for the Protection Plan near the expiration of the two-year manufacturer’s warranty on the picture tube. For additional information call (256) 774-4088.

Zenith HealthViewTMDirect-View TV Receiver Warranty

Additional Zenith Picture Tube Protection Plan Available

Zenith offers you the opportunity to obtain additional long-term protection against failure of the picture tube in your new television. Our Picture Tube Protection Plan enables you to avoid any unexpected picture tube repair expenses and keep your television in top condition. It guarantees you a genuine Zenith replacement picture tube and service from a Zenith authorized service center.

C-HEALTHVIEW 12/99

206-3584

Issue*

ZENITH ELECTRONICS CORPORATION

Zenith Response Center 201 James Record Road Building 3 Huntsville, AL 35824 Telephone (256) 772-1515 Mon-Fri, 7:00 a.m.-8:00 p.m. CST Sat, 8:00 a.m.-5:00 p.m. CST www.zenith.com

801 E. Roosevelt Rd. Lombard, IL 60148 Telephone (630) 705-2830

Home & Carry-in Service Television/VCR Parts and Accessories PTV/Camcorders

201 James Record Rd. Building 4 Huntsville, AL 35824 Telephone (256) 774-4025

Service Hours: M-F 8-6, Sat 9-2 Will accept UPS shipments

ZENITH CONSUMER SERVICES FACTORY OWNED SERVICE CENTERS