© Copyright 2003, Zenith Electronics Corporation
table of contents
page
5
Installation / Operating Guide | Warranty
Model Numbers ||H19F34DT ||H20F34DT ||H25F34DT
||
ConciergeTMTVs
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
POWER CORD POLARIZATION:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.
Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is:
Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069, USA. Phone: 1-847-941-8000.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
2-WIRE COMM WARN
ConciergeTMis a trademark of Zenith Electronics Corporation
© Copyright 2003 Zenith Electronics Corporation
RECORD THE MODEL NUMBER
The model and serial number of the ConciergeTMTV are located
on the back of the cabinet. For future reference, we suggest
that those numbers be recorded here:
MODEL NO.____________________________________
SERIAL NO.____________________________________
For Customer Support/Service please call:
1-888-865-3026
www.zenith.com
PAGE 3
206-3743
1. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
The safety and operating instructions should be retained for
future reference.
4. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
5. Cleaning
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
6. Water and Moisture
Do not use this product near water for example, near a
bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
7. Accessories, Carts, and Stands
Do not place this product on a slippery or tilted surface, or
on an unstable cart, stand, tripod, bracket, or table. The
product may slide or fall, causing serious injury to a child
or adult, and serious damage to the product. Use only with
a cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any mounting of
the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer.
8. Transporting Product
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
9. Attachments
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not
be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in
a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult
your product dealer or local power company. For products
intended to operate from battery power, or other sources,
refer to the operating instructions.
12. Power Cord Polarization
This product is equipped with a polarized alternating-current power plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
13. Power Cord Protection
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit
from the product.
Important safeguards for you and your new product
This product has been manufactured and tested with your safety in mind. However, improper use can result in potential
electrical shock or fire hazards. To avoid defeating the safeguards that have been built into the new product, please read
and observe the following safety points when installing and using the new product, and save them for future reference.
Observing the simple precautions discussed in this installation and operating guide can help the lodge get the many years
of enjoyment and safe operation that are built into the new product.
(Continued on next page)
IMPORTANT SAFETY INSTRUCTIONS
PORTABLE CART WARNING
(Continued from previous page)
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded so
as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical
Code (U.S.A.), ANSI/ NFPA 70 provides information with
regard to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
15. Lightning
For added protection for this product (receiver) during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
16. Power Lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can
result in a risk of fire or electric shock.
18. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
19. Servicing
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been
damaged.
f. If the product exhibits a distinct change in performance.
21. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to determine that the product is in proper operating condition.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer. The product may slide or
fall, causing serious injury to a child or adult, and serious
damage to the product.
24. Heat
The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
PAGE 4
206-3490-O
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
Ground Clamp
Electric Service
Equipment
Example of Grounding According to National Electrical
Code Instructions
NEC - National Electrical Code
IMPORTANT SAFETY INSTRUCTIONS
206-3852
PAGE 5
Table of Contents
Purchase the Optional Installer’s Remote
To perform a normal installation set up, you need an installer’s remote like the LP702. The LP702 is shown and described
in later sections. The installer remote allows access to the Installer’s menus, and User menus. The installer remote has
Menu, Select, and Adjust Keys (Down/Left/Right arrow) keys. To purchase the LP702 remote, see your Zenith Dealer.
Installer/Hotel Note:
Pages 40, 41, 42, and 43 contain information and menus which the guest can use to operate the TV.
It is recommended that these four pages be copied and included with the literature packet that the
hotel provides to the guest.
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safety Instructions . . . . . . . . . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 1. Hook Up TV
TV and other Equipment Hookups
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cable service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cable service with VCR . . . . . . . . . . . . . . . . . . . . . . . 9
External Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Step 2. Channel Search and Reception Setup
Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
(Select Antenna, or cable service and perform channel
search)
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 12
Guest’s Remote Key Functions . . . . . . . . . . . . . . . . . 13
Installer’s Remote Key Functions . . . . . . . . . . . . . . . . 14
On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . 15
Step 3. Customize the ConciergeTMTV’s Features
Setup Menu (Start with page 11, Auto Program)
Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Timer (On/Off Timer) . . . . . . . . . . . . . . . . . . . . . . . 19
Captions (Caption/Text) . . . . . . . . . . . . . . . . . . . . . 20
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installer Parental Control Menu . . . . . . . . . . . . 23 - 24
Other Menus and On-Screen Displays . . . . . . . . . . . . . 25
Managing the Channel Banks . . . . . . . . . . . . 26 - 27 - 28
Installers Menus . . . . 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36
LT2000 Quickset II Clone Programmer . . . . . . 37 - 38 - 39
Guest Operation Section (Copy for guest usage)
Guest Remote Control Key Functions . . . . . . . . . . . . . 40
Guest Parental Control Menu . . . . . . . . . . . . . . . 41 - 42
Guest Menus and On-Screen Displays . . . . . . . . . . . . . 43
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Warranty for Concierge
TM
Series TVs . . . . . . . . . Back Cover
ConciergeTMis a trademark of Zenith Electronics Corporation
Use the steps outlined below as a setup guide and to determine the TV features
that will require adjustment for the needs of the end user
PAGE 6
206-3745
Mini glossary
75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire
sticking through the middle, and it screws onto the threaded jack on the back of your TV.
A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws
on one end and a round opening with a wire sticking out on the other end.
Antenna Hook Up
Connect an over-the-air antenna to the Concierge TV
If you have a 75 ohm RF cable, then you don’t need any
adapters!
A 300 to 75 ohm adapter is not included with the Zenith
Concierge TV.
300 TO 75 OHM
ADAPTER
Antenna
Flat Wire
(300 ohm)
300/75 ohm
Adapter
TV Back Panel
(Expanded View)
TV Back
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
RF Coaxial Wire
(75ohm)
Antenna
TV Back
TV Back Panel
(Expanded View)
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
Locate the Antenna/Cable jack on the back of the
Concierge TV.
Connect the antenna wire that runs from the wall,
according to one of the diagrams to the right.
Remove the back of the remote and put in two AA
batteries.
Plug in the TV. Concierge TV is designed to operate
on standard current, 120-volt 60 Hertz AC. Do not
attempt to operate it on DC power.
Go to page 11 to Auto Program the TV.
Back of
Remote
120 V AC
60 Hz
1
2
3
4
5
PAGE 7
206-3745
Cable Service Hook Up (CATV)
If you’re using a cable box, leave the TV tuned to channel 3
or 4 and use the cable box to change channels.
If you’re using a cable box, Auto Program might only find the
channel your cable service is on (usually channel 3 or 4).
Cable TV
Wall Jack
RF Coaxial Wire
(75ohm)
TV Back
TV Back Panel
(Expanded View)
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
Cable TV
Wall Jack
Cable Box
In
Out
3 4
Output
Switch
RF Coaxial Wire
(75ohm)
TV Back Connections Panel
(Expanded View)
TV Back
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
Locate the Antenna/Cable jack on the back of the
Concierge TV.
Connect the cable service wire that runs from the wall,
according to one of the diagrams to the right.
Remove the back of the remote and put in two AA batteries.
Plug in the TV. The Concierge TV is designed to operate
on standard current, 120-volt 60 Hertz AC. Do not
attempt to operate it on DC power.
Go to page 11 to Auto Program the Concierge TV.
Back of
Remote
120 V AC
60 Hz
1
2
3
4
5
Connect cable service to the Concierge TV
PAGE 8
206-3745
Antenna With VCR Hook Up
Connect an off-air antenna and VCR to the Concierge TV
No A/V cables are included with the TV.
TV Back
TV Back Panel
(Expanded View)
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
Flat wire
(300 ohm)
Antenna
300/75 ohm
Adapter
In
Out
Audio
Video
3 4
VCR Back
VCR Back AV Panel
output
switch
TV Back
TV Back Panel
(Expanded View)
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
A/V Cables
Not included
with TV
RF Coaxial Wire
(75ohm)
Antenna
In
Out
Audio
Video
3 4
VCR Back
VCR Back AV Panel
output
switch
Locate the Antenna/Cable jack on the back of
the VCR.
Connect the antenna wire that runs from the
antenna, according to one of the diagrams to
the right. Make other connections as needed.
Remove the back of the remote and put in two
AA batteries.
Plug in the TV. The Concierge TV is designed to
operate on standard current, 120-volt 60 Hertz
AC. Do not attempt to operate it on DC power.
Go to page 11 to Auto Program the TV.
Back of
Remote
120 V AC
60 Hz
1
2
3
4
5
PAGE 9
206-3745
Cable Service (CATV) with VCR Hook Up
Connect a VCR and Cable service to the Concierge TV
Leave the VCR and the television tuned to channel
three and use the cable box to change channels.
No A/V cables are included with the TV.
TV Back
TV Back Panel
(Expanded View)
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
Cable TV
Wall Jack
Cable Box
In
Out
3 4
Output
Switch
A/V Cables
Not included
with TV
RF Coaxial Wire
(75ohm)
In
Out
Audio
Video
3 4
VCR Back
VCR Back AV Panel
Output
Switch
TV Back
TV Back Panel
(Expanded View)
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
Cable TV
Wall Jack
A/V Cables
Not included
with TV
RF Coaxial Wire
(75ohm)
In
Out
Audio
Video
3 4
VCR Back
VCR Back AV Panel
Output
Switch
Locate the Antenna/Cable jack on the back
of the VCR.
Connect the cable service wire that runs
from the wall, according to one of the diagrams to the right. Make other connections
as needed.
Remove the back of the remote and put in
two AA batteries.
Plug in the TV. The Concierge TV is designed
to operate on standard current, 120-volt 60
Hertz AC. Do not attempt to operate it on
DC power.
Go to page 11 to Auto Program the TV.
Back of
Remote
120 V AC
60 Hz
1
2
3
4
5
PAGE 10
206-3745
External Speaker Hook Up
Locate the Audio In jack on the back of the external speaker.
Connect a standard audio cable from the Speaker
Out jack on the TV, to the Audio In jack on the
external speaker.
TV Back Panel
(Expanded View)
VIDEO
IN
ANTENNA
CABLE
M.P.I.
Super
Port
SPEAKER
OUT
AUDIO
IN
Audio In
Speaker back
TV Back
1
2
Connect an external speaker to the Concierge TV
PAGE 11
206-3745
Auto Program (Channel Search)
Use Auto Program to specify Antenna or cable service
incoming signal source and automatically store all of the
channels that are found by the channel search
Using an Installer remote control, press the POWER key to
turn on the Concierge TV.
Press the MENU key to show the SETUP MENU.
Using SELECT on the remote control, highlight AUTO
PROGRAM on the screen.
Press the Right or Left ADJ (Adjust) arrow to go to the
Auto Program menu.
Using SELECT, choose either CABLE TV or OFF AIR ANTENNA
on your screen.
Press the Right or Left ADJ arrow key to begin the Channel
Search.
Press ENTER when the channel search is complete.
1
2
3
4
5
6
7
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
MENU
ALARM
ADJ
ADJ
SELECT
3/5
AUTO PROGRAM
ADD/DEL/BLNK
CH. LABELS
CLOCK SET
TIMER
CAPTIONS
LANGUAGE
TO PROGRAM
SETUP MENU
Mini glossary
OFF AIR ANTENNA If the guest can only view over-the-air broadcasts, select Antenna.
CABLE If you provide cable service to your guests, select Cable.
Note: Auto Program finds channels being received by the TV
tuner.
Cable will not work unless the lodge provides a cable service.
4/6
1
7
2
PAGE 12
206-3852
Front Panel Controls
1
2
3
4
Use the front control panel to access the menus or just operate the TV
Note: Item 11 Key Defeat, in the installer’s menu allows the installer to:
Set Menu Option 11, Key defeat to “0” - Front panel controls give access
to menus.
Set Menu Option 11, Key defeat to “1” - Menus not available with front
panel controls.
Front panel control menu operation buttons are not
labeled and are not usually available to the guest.
You can use Channel to tune to available channels and
Volume to set the sound level, regardless of the key
defeat setting.
Camport jacks are not available on some models.
Press POWER to turn on your TV.
To access the menus, press the MENU button on
the control panel. Cycle through the various
menus by pressing MENU repeatedly.
Use the SELECT button to highlight the option
you want to modify.
Use either the Right or Left ADJUST button to
modify the option you have chosen.
Press CAPTIONS to turn captions on and off.
The menu will disappear after a few seconds.
TV Operation
Power turns the TV on and off.
Channel Up/Down tunes to next channel.
Volume Up/Down adjusts sound level.
Captions turns selected Caption/Text option on
and off.
Camport: Front Audio/Video Inputs
Video Input
L-Audio-R Inputs
Note: TV sound is always monaural. Left/Right
Audio input is processed into monaural sound
by the TV.
5
adjust select menu
captions volume channel power
L audio R
video in
2
4
3
H25F34DT Front Panel Controls
1/A
C
B
5/D
F
E
A
B
C
D
E
F
power
channel
volume
captions
CAPTION
VOL
VOL
CH
CH
OFF
ON
H20F34DT
H19F34DT
PAGE 13
206-3852
Guest’s Remote Key Functions
TIMER ALARM
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
CC
FLASHBK (FLASHBACK)
Returns to the last channel viewed.
POWER
Turns TV On or Off
.
CHANNEL (UP/DOWN)
Scrolls through available channels, and
the Video Channel (Audio/Video source).
MUTE
Turns sound Off and On, while the
picture remains.
ENTER
Press to view the Channel/Time
display or to remove any on-screen
display or menu.
NUMBER KEYPAD
Selects channels directly: enter channel
numbers and press ENTER to go to new
channel
.
remote control part number
SC652Z
124-213-18
6710V00108A
TIMER
Press repeatedly to choose a TV
turn-off time, up to 4-hours.
Use to pick AM/PM in the Alarm menu.
VOLUME LEFT/RIGHT
Adjusts the sound level.
CHANNEL PREVIEW
Displays the available TV channels, including access to guest’s Parental Control
menu. Allows guest to select the Aux
Channel. (Use the Audio/Video jacks on
the back of the TV as the source of the
picture and sound.)
CC (CLOSED CAPTIONING)
Press to access closed captions.
Press ENTER to exit.
A brief overview of the keys on the guest’s remote and what their function
ALARM
Press to display menu, then follow onscreen instructions to set a TV turn-on
time.
PAGE 14
206-3490-O
Installer Remote Key Functions
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
MENU
ALARM
ADJ
ADJ
SELECT
FLASHBK (FLASHBACK)
Returns to the last channel viewed.
POWER
Turns TV On or Off
.
CHANNEL (UP/DOWN)
Flips through available channels.
MUTE
Turns sound Off and On, while the
picture remains.
ENTER
Press to view the Channel/Time display or
to remove any on-screen display or menu.
NUMBER KEYPAD
Selects channels directly and enters
numeric values for some options
.
remote control part number
LP702
124-213-04
TIMER
Press repeatedly to choose a TV
turn-off time, up to 4-hours.
Use to pick AM/PM in the Clock/Alarm
menus, on some TVs.
VOLUME LEFT/RIGHT
Adjusts the sound levels.
CC (CLOSED CAPTIONING)
Press to access closed captions.
Press ENTER to exit.
An overview of the keys on the LP702 installer’s remote and what they do
ALARM
Press to go to the Alarm menu. Set a
time for the TV to turn itself on.
MENU/SELECT/ADJ (ADJUST)
Press MENU repeatedly to scroll through
either the Installer, or User menus. Use
SELECT to choose an option and ADJ
(adjust) to change the selected option.
CHANNEL PREVIEW
Gives installer access to the guest’s
menus. Displays the available TV channels and hotel guest’s Parental Control
menu. Allows user to select the Aux
Channel. (Use the Audio/Video jacks on
the back of the TV as the source of the
picture and sound.)
TV/FM
Selects TV or Radio on TVs equipped with
FM radio.
PAGE 15
206-3745
On-Screen Menus Overview
ON-SCREEN MENUS
SETUP MENU Adjusts the basic characteristics of the TV
Auto Program 11 Automatically finds and stores active channels in memory to scroll through using Channel Up/Down.
Add/Del/Blnk 16 Picks and chooses which active channels will appear when using Channel Up/Down
Channel Labels 17 Labels available channels with their network names (ABC, CBS, HBO, etc.).
Clock Set 18 Sets the time.
Timer 19 Sets times for the TV to turn itself on and off each day.
Captions 20 Chooses the captioning or text option.
Language 21 Select the language the on-screen menus will appear in.
VIDEO MENU 22 Adjusts the picture settings. The options are: Contrast, Brightness, Color,
Tint, Sharpness, Picture Pref.
PARENTAL 23 Allows installer to block any channel or A/V source for up to 99 hours, with the use of a password.
CONTROL MENU
25 OTHER MENUS AND ON-SCREEN DISPLAYS
Channel/Time Shows the current time, channel, video, type of incoming audio signal, and XDS* data if available.
Alarm Sets a time for the TV to automatically turn itself on.
Sleep Timer Sets the time the TV will turn itself off.
Volume Shows current sound level.
Captions Selects Caption/Text options.
Ch Preview Displays the available channels list, access to Parental Control, and Aux source selection.
Channel Bank Shows currently selected channel bank.
INSTALLER MENUS
INSTALLER MENUS 29 Make adjustment to the TV’s operational features.
*XDS (Extended Data Service) Additional program information provided at the
discretion of the broadcaster. May include: title of broadcast, elapsed time, and time
remaining on program.
Descriptions of the menus and on-screen displays on the TV available to the installer
Using the Menu button on the installer’s remote, the installer can access all the menus below.
Menu Name Page Description
PAGE 16
206-3599-O
Fine-tuning the guest’s channel selection list
Channel Add/Delete/Blank
Press the MENU key on an Installer’s remote so the SETUP MENU
appears.
Press SELECT repeatedly to go to the Add/Del/Blnk option.
Using either the NUMBER keypad and ENTER or the Channel
Up/Down arrows on the remote, select a channel. (If adding a
deleted channel, you will need to use the number keypad and
ENTER.)
Using the Right/Left ADJ arrows, pick whether that channel is
Added, Deleted, or Blank.
To continue, select another channel and repeat from Step 3.
When you are finished, press ENTER to remove menu.
Adding Aux, VCR 3, or VCR 4 to the Channel
Preview List
Go to the Setup menu, select the Add/Del/Blnk option. Use
Channel Up/Down to select the option and choose Added.
Note: If the option was turned off in the Service menu, you will
have to reinstate it before it can appear as an option in the
Channel Preview list.
Note: You can Add, Delete, or Blank: VCR 3, VCR 4, and Aux.
Caution: If you delete CH3, VCR3 is deleted also, if you delete
CH4 VCR4 is deleted also, and vice versa.
1
2
3
4
5
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
MENU
ALARM
ADJ
ADJ
SELECT
2
CH 44 ADDED
AUTO PROGRAM
ADD/DEL/BLNK
CH. LABELS
CLOCK SET
TIMER
CAPTIONS
LANGUAGE
SETUP MENU
Mini glossary
ADD Adds new channels to the list that the guest can scroll through when using the remote.
DELETE Removes channels for one reason or another from the list that the guest can scroll through.
BLANK Removes the video signal from a channel so the guest will only receive the audio signal
.
4
3/5
1
If you delete a channel, it isn’t gone for good. Just select it
using the NUMBER keypad on the remote, or add it later.
3
3
PAGE 17
206-3599-O
Setting Up Channel Labels
Customizing the channel selection names
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
MENU
ALARM
ADJ
ADJ
SELECT
AUTO PROGRAM
ADD/DEL/BLNK
CH. LABELS
CLOCK SET
TIMER
CAPTIONS
LANGUAGE
CH 32 ABC
SETUP MENU
Overview
Channel Labels help the user identify the channel or network being viewed.
In the Setup menu with the CH. LABELS option highlighted, use the Adjust
Left/Right arrows to scroll through the available channel labels, such as,
A & E, AMC, ESPN, HBO, etc. These are a series of alphabetically organized preset
labels from which you can choose the more common networks. Use any of these or
create custom labels.
- - - - , The 4 dashes will allow a channel label to appear; if one is provided by
XDS. (Extended data service)
NONE, prevents any channel label from appearing.
LAB 1, thru LAB 20, are the 20 programmable labels.
The 20 programmable labels can be customized for your needs.
Each programmable label has 5 characters spaces available.
Creating Custom Channel Labels
First select a channel using the NUMBER keypad and ENTER or the Channel
Up/Down arrows, on an Installer’s remote control. (To select a deleted channel,
use the NUMBER keypad and ENTER.)
To create a channel label, go to the SETUP MENU and select CH. LABELS.
Press the Right/Left ADJ key to scroll the available preset labels. Scroll past - - - -
, scroll past NONE, to go to the first programmable label slot, LAB 1. (Label 1)
Notice that the label appears with the title LAB 1, and is also on a dark background; which will distinguish it from the preset labels.
Operating the Menu to Create Custom Labels
Use Volume Up/Down to select the first letter; when it blinks it is selected.
Press MUTE to clear the label if necessary.
Use Channel Up/Down to change the character to one of the 255 characters avail-
able. (A blank letter space is available if required, after the “!” symbol.)
Adjust Left/Right Switches to the next label.
- - moves to the next or previous
label.
Volume Up/Down Selects character spaces
- - moves to the next or previous
character space.
Channel Up/Down Scrolls through the available
characters.
ENTER Accept the channel label and
removes the menu.
MUTE Removes any custom label, inserts NONE
- - if any custom character space is selected.
You can press and hold down
Channel Up/Down to scroll
through the available
characters rapidly.
PAGE 18
206-3683
Set the Clock
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
MENU
ALARM
ADJ
ADJ
SELECT
AUTO
EASTERN
CENTRAL
MOUNTAIN
PACIFIC
CLOCK MENU
CLOCK SET
TIME ZONE
DAY. SAVING
USE SELECT TO CHOOSE
USE ADJ TO CHANGE
AUTO
AUTO
OFF
ON
10:43 AM
CLOCK MENU
CLOCK SET
TIME SET
MANUAL
TIMER
AUTO PROGRAM
ADD/DEL/BLNK
CH. LABELS
CLOCK SET
TIMER
CAPTIONS
LANGUAGE
SETUP MENU
TO SET CLOCK
AUTO PROGRAM
ADD/DEL/BLNK
CH. LABELS
CLOCK SET
TIMER
CAPTIONS
LANGUAGE
SETUP MENU
TO SET CLOCK
USE SELECT TO CHOOSE
2
4
3
3
Mini glossary
TIME A four-digit figure broken down into hours and minutes, used to enter the current time when setting the clock or wake-up alarm.
HOURS First two digits that are entered when setting the clock or the wake-up alarm.
MINUTES The last two digits that are entered when setting the clock, or the wake-up alarm.
TIMER Chooses AM or PM when setting the clock.
Clock Auto/Manual Operating Modes Setup
Use MENU, SELECT, and ADJ Left/Right to choose the Clock menu and to
set up the clock menu options.
Clock Mode Auto: TV automatically sets the time.
Time Zone: User can choose the time zone or have the
TV set it automatically.
Day. Savings: User can choose to have daylight
savings adjust the clock time one hour, or have the TV
adjust it automatically.
Manual: User sets the time on the clock.
Press ENTER repeatedly to remove menus.
1
3
The clock can also be set using 24 hour “military time.” For p.m. settings
add 1200. For example, to set 6:30 p.m., add 1200 to 630, = enter 1830.
For Auto Clock Set to work, TV must be tuned to a channel that has XDS
data available. Auto Clock Set, sets the time only once while the TV is on.
To set the clock with XDS data, turn TV off, then back on again, or set the
clock time manually.
PAGE 19
206-3745
On/Off Timer Setup
ON TIME 9:00 AM
OFF TIME 7:00 PM
ON/OFF TIMER
ON
TIMER
AUTO PROGRAM
ADD/DEL/BLNK
CH. LABELS
CLOCK SET
TIMER
CAPTIONS
LANGUAGE
TO SET TIMER
SETUP MENU
Set up On/Off Timers
Note: On/Off Timers
operate independently of
each other.
On the optional HP602 Installer’s remote, press MENU
repeatedly until the Setup menu appears.
Press SELECT repeatedly to highlight the Timer option, press
the Right arrow.
Use SELECT to choose an option. Use the number keypad
and/or the Left/Right ADJ arrows to enter the times. Use the
TIMER key to set AM/PM.
Your options are:
• On Time
Sets a time that the TV will turn itself On each day.
• Off Time
Sets a time that the TV will turn itself Off each day.
• On/Off Timer
Enables or disables the On/Off Timer functions. (The On/Off
Timer can be disabled but the settings will be retained.)
Press ENTER to remove menu and return to TV viewing.
The clock must be set before the Timers will function.
The Off Timer can be used to turn the TV off at the preset time.
Note: No On Timer setting is required to use the Off Timer feature.
Mini glossary
TIME A four-digit figure broken down into hours and minutes, used to enter the time when setting the clock or programming timers.
HOURS First two digits that are entered when setting the clock or programming timers.
MINUTES The last two digits that are entered when setting the clock, or programming timers.
TIMER Choose AM or PM with the TIMER button when setting the clock.
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
MENU
ALARM
ADJ
ADJ
SELECT
2/3
2/3
4
1
1
2
3
4
3
PAGE 20
206-3490-O
Captions (Caption/Text Set Up)
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
1
Caption/Text are features which allow the Concierge TV to receive the closed
caption and/or text options if made available by the broadcaster.
Availability and functionality of Caption/Text options are determined only by each
broadcaster and may not be available in your area.
2
Standard closed captioning is available using the Caption 1 option.
OPER. MODE
SEL. TYPE
CAPTION
ON MUTE
CAPTION LOCK
CAPTION 1
CAPTION 2
CAPTION 3
CAPTION 4
TEXT 1
TEXT 2
TEXT 3
TEXT 4
OFF
CAPTIONS SETUP
OPER. MODE
SEL. TYPE
CAPTION LOCK
CC
CC
PRESS SELECT TO CHOOSE
PRESS ADJ TO CHANGE
STANDARD
ON, OFF
CC
CAPTION 1
CAPTION 2
CAPTION 3
CAPTION 4
TEXT 1
TEXT 2
TEXT 3
TEXT 4
TO SET CAPTIONS
CAPTIONS SETUP
CC
PRESS SELECT TO CHOOSE
PRESS ADJ TO CHANGE
QUICK/MUTE
ON, OFF
ON, OFF
ON, OFF
AUTO PROGRAM
ADD/DEL/BLNK
CH. LABELS
CLOCK SET
TIMER
CAPTIONS
LANGUAGE
SETUP MENU
TO SET CAPTIONS
AUTO PROGRAM
ADD/DEL/BLNK
CH. LABELS
CLOCK SET
TIMER
CAPTIONS
LANGUAGE
SETUP MENU
Mini glossary
CAPTIONS The term for the words that scroll across the bottom of your TV screen; usually the audio portion of the program
provided for the hearing impaired.
TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages
provided by the broadcaste
r.
Set up Closed Caption/Text options for the user
Closed Captions/Text Operating Modes Setup
Use MENU, SELECT, and ADJ Left/Right to choose the Closed Captions/Text
mode and to set up the other menu options for the user.
Quick/Mute When CC is pressed: User can only turn Captions on/off.
(If CC on Mute is on, shows captions option on mute.)
(If locked, type is retained with Power on/off.)
Standard When CC is pressed: User can choose a captions type.
(If locked, type is retained with Power on/off.)
Press ENTER repeatedly to remove menus.
PAGE 21
206-3490-O
Language
AUTO PROGRAM
ADD/DEL/BLNK
CH. LABELS
CLOCK SET
TIMER
CAPTIONS
LANGUAGE
ENGLISH
SETUP MENU
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
MENU
ALARM
ADJ
ADJ
SELECT
2
1
4
Choose the language the on-screen menus
will appear in
Press the MENU key on the remote control so the Setup
menu appears.
Use the SELECT key on the remote control, to highlight Language
on your screen.
Use the Right/Left ADJ arrow to choose one of the following
options: English, Spanish, or French.
Press ENTER to return to TV viewing.
1
2
3
4
3
PAGE 22
206-3490-O
Video Menu
Press the MENU key repeatedly until the Video menu appears.
Your options are:
• Contrast: Adjusts the level of difference between white and
black in the TV picture. The more contrast, the brighter the
picture appears.
• Brightness: Increases or decreases amount of white in the TV
picture.
• Color: Adjusts levels of all colors in the TV picture.
• Tint: Balances between amounts of red and green in the TV
picture.
• Sharpness: Raises or lowers the definition of the TV picture.
The lower the level, the softer the images will appear.
• Picture Preference: Choose either Custom or Preset. Custom
allows you to set the picture the way you want. Preset moves
all the above options back to their original, factory-set levels.
Using SELECT on the installer’s remote control, choose Contrast
on your screen.
Using the Right/Left ADJ arrow, change the contrast level to
your preference.
Press ENTER, or MENU one more time to return to TV viewing,
or repeat from step two to set the other menu options.
Picture Preference
Use SELECT to choose Picture Preference on your screen.
Use the Right/Left ADJ arrows, to choose either the original
settings with Preset, or use your own settings with Custom.
1
2
3
4
A
Choose the Preset option in Picture Preference to quickly reset the
Video menu settings to their original values.
Use the Video menu to customize the picture appearance
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
PICTURE PREF
PRESET
VIDEO MENU
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
MENU
ALARM
ADJ
ADJ
SELECT
2/A
4
3/B
B
1
PAGE 23
206-3852
Installer Parental Control Menu
Overview
To insure complete coverage for all TV programs, (movies and regular TV shows) choose a rating for MPAA, from the selections below AND choose ratings from the TV Parental Guidelines Rating System on the next page, using the Age Block
option for General Audiences and for Children. In addition to those, you may wish to add additional restrictions from the
Content Block menu. See the Parental Control menu, and submenus example on the next page.
Things to Consider before Setting Up Parental Control
Determine which rating you consider acceptable to the viewer. (For example, if you choose TV-PG, all more restrictive ratings will be automatically blocked; the viewer will not be able to see: TV-PG, TV-14, or TV-MA rated programming.)
Do you want to block the auxiliary video source entirely? (Blocks the signal sent by the equipment, such as a VCR, connected to the TV Audio/Video input jacks; in the Aux. Block option.) Or leave unblocked, then choose allowable ratings.
Block program “Content” based on individual parameters such as: Strong Dialog, Mature Language, Sex Scenes, Violence
Scenes, or Fantasy Violence Scenes; in the Content Blk option.
How many hours do you want Parental Control to be active? You can set the Hours option for up to 99 hours.
Select a secret password; in the Set Password option. Use the number keys on the remote. Don’t forget the password, it is
the only way you can access the Parental Control menu and change rating selections, or turn Parental Control off.
Do you want Parental Control to be active all the time? If not, you can turn it on or off; with the Lock On/Off option.
If used, this optional feature can “block” undesirable programming from appearing on the TV
You can set different Parental Control viewing restrictions for general audiences and for children - - both can
be active at the same time
.
Simply specifying one content block such as Sex Scenes,
will not automatically block another content in the programs from appearing.
Parental Control offers the user a wide variety of options and settings that restrict or “block” the programming that can
appear on the TV. Parental control allows the user the capability of defining which program rating they consider acceptable, to the younger or more sensitive viewer. It can be preset and turned either on or off by the user who specifies the
secret 4-number code, the password. The number of hours blocked are specified. General audience and children viewer
blocks can both be programmed into the TV’s memory. Viewer ratings are specified for both TV and the motion picture
industry; both rating systems can be used. The ratings are based mainly on the ages of children.
You cannot disable Parental Control by disconnecting the TV
from power. Block hours remaining will be retained if power is
lost or power cord is disconnected.
The AUX input source can also be blocked.
Reset Parental Control Block Hours to Zero and Cancel Password
This provides the lodge staff and the installer a means to reset the TV to normal operation, if a guest
has either forgotten the password or has left Parental Control Block active after checking out.
On the installer’s remote control, press and hold down MENU until the menu disappears (about 6 seconds). Immediately press 9, 8, 7, 6 and then CC. (Based on 0-I INST. SEQ. ‘0’ setting.) This will reset
the Block Hours to Zero and cancel the current 4-number password.
PAGE 24
206-3852
Installer Parental Control Menu
After you have read the preceding page, follow instructions below to set up and activate Parental Control.
Note: Use the installer’s remote control to
specify Parental Control settings.
TIMER
CH PREVIEW
ENTER
7
8
9
0
MENU
ALARM
ADJ
ADJ
SELECT
2
3
1
1
2
3
4
Press MENU repeatedly until the Parental Control Menu appears.
With the Parental Control menu on-screen, use the SELECT button to
access the MPAA menu and customize the level of restriction.
Use the Left/Right ADJ arrow to adjust or set the rating for an option,
for example, use the “PG” setting. (See the Mini Glossary, Ratings Charts
on pages 40 and 41 for rating descriptions.)
After you have selected and adjusted the Parental Control menu options
to your preferences:
- Set the number of hours Parental Control will be on.
- Set a 4-number password, using the number keypad.
- Set the Lock On/Off option to either On or Off.
On= Programs will be restricted.
Off= Programs will not be restricted; although restriction
settings will be retained.
Note: Some broadcasts do not include rating information.
SETUP MENU
DIALOG
LANGUAGE
SEX SCENES
VIOLENCE
F VIOLENCE
NO RATING
TO BLOCK
GENERAL
CHILDREN
AGE BLOCK
UNBLOCKED
CONTENT BLOCK
TO BLOCK
AUX SOURCES
MPAA RATING
AGE BLOCK
CONTENT BLK
SET HOURS
SET PASSWORD
LOCK ON OFF
PARENTAL CONTROL
VIDEO MENU
PRESS CC TO RETURN
PRESS CC TO RETURN
UNBLOCKED
Make Parental Control restrictions permanent,
with no preset or fixed hours time limit
In the Installer’s Menu, Item 84: PERMANENT BLK, 0 or 1.
0 Blocking restrictions always active, no time limit.
1 Restrictions limited to specified hours, 12 - 99.
Reset the Maximum Number of Parental
Control Default Block Hours
You can change the Block hours from the 12-hour default
setting to up to 99 hours.
In the Installer’s Menu, item: 22-I MAX BLK HRS 12,
use the ADJ Left/Right adjust arrow to set a different
default number of hours.
To Turn the Parental Control Feature Off/On
In the Installer’s Menu,
Items: 21-I V-CHIP, 0 or 1, 51-I DIS. VCHIP M., 0 or 1
Options Setups for V-Chip Menu and Block Functions
21-I V-CHIP 51-I DIS. VCHIP M.
0 0 No menu, no blocking.
0 1 No menu, no blocking.
1 0 Shows menu, Block functions.
1 1 No menu, Block functions.
PAGE 25
206-3490-O
Other Menus & On-Screen Displays
SLEEP TIMER
OFF
PRESS TIMER
Ch 25 - PBS
7:15
OLD TIME MOVIES
LENGTH 01:00 TIME LEFT 00:36
PM
Channel/Time/XDS Display
Press ENTER. Shows currently
selected channel or source, current
time if the clock has been set,
incoming audio signal, and XDS
data (if available).
Volume Display
Press VOLUME. Shows currently
selected sound setting.
Closed Captions Menu
Press CC. Turns selected option on
or off. See Caption/Text page to
select options.
PRESS DIGITS TO SET TIME
TIMER TO SELECT AM/PM
ALARM MENU
TIME NOW 3:11 PM
6:10 AM
TIMER
Alarm Menu
Press ALARM. Sets a time the TV
will turn itself on. (Clock must be
set.)
CHANNEL PREVIEW
5 - - - 9 - - - 20 - - - 32 - - - 44 - - - AUX - - - -
CC FOR PARENTAL CONTROL
CH TO SELECT, ENTER TO QUIT
VOLUME
Press the remote keys indicated below to access these menus and displays
Channel Banks Menu
Press SOURCE/BANK on an Installer
remote equipped with those keys.
Accesses the Channel Banks menus:
Bank 1, Bank 2, Bank 3, Bank 4.
CHANNEL BANK
BANK 3
CAPTION 1 IS ON
CC
Sleep Timer Menu
Press TIMER. Shows remaining time
before TV shutoff. Choose a preset
time for TV turn-off.
Ch Preview Menu
Press CH PREV. Displays list of the
available TV Channels, Guest
Parental Control menu, and used to
select Auxiliary input source.
PAGE 26
206-3490-O
PLANNING THE CHANNEL BANKS
Generally, TV channels are grouped into “program pack-
ages” with terms that are proposed to the end user. The
user then opts for a package. Below is an example of how
TV channels may be grouped.
You may plan your package by using a chart like the one
after the following page.
Remember, you can “blank” a channel for accommodating
audio-only, such as an FM radio station or in-house com-
munication.
Sometimes, only one or two channel banks may be need-
ed. You may leave any unused bank with the channels
entered during Auto Program; or, you may delete the chan-
nels. However, you may want to leave at least one channel
in any unused bank. Then, if someone selects an “unused”
bank, that channel will assure them that the TV is func-
tional.
Note: Some channels from factory testing may be in the
channel banks if you have not yet run Auto Program.
ADDING / DELETING CHANNELS
A previously prepared programming chart is helpful.
1. Run Auto Program (in the Setup menu). All channels
found on your cable/antenna will be entered in
Channel Banks 1, 2, 3, and 4.
Note: Be advised that running Auto Program overwrites
any custom channel setups; removes Blanked, Deleted.
2. Select a channel bank with an installer remote - -press
SOURCE/BANK (and repeat). CHANNEL BANK and BANK
number will be displayed.
3. Use the ADD/DEL/BLNK item (also in the Setup menu)
to customize your program package. You may delete
channels or add some that have not been entered. You
can also “Blank” a channel for accommodating an
audio-only program source or in-house communication.
See the “ADD/DEL/BLNK” menu page for more details.
Note: The Blank Channel feature is global. A channel
will be blanked in all channel banks.
4. Repeat steps 2, and 3 to program another channel
bank.
Managing the Channel Banks
The TV has four channel banks, where the administrator or installer can store groups of TV channels
Note: Channel banks set up requires an installer’s remote with “Source” or “Bank” keys like the Zenith
MBR3447, or a similar remote.
Channel Bank Program package
1 Basic cable channels
2 Extended cable channels
3 Extended with premium channels
4 Other cable service options
(Grouping is provided as an example only.)
The BLNK (blank) channel function is “global” -- the same
channel number is blanked in channel banks 1, 2, 3, and 4.
Channel Bank Number Display
CHANNEL BANK
BANK 1
PAGE 27
206-3490-O
B Purpose Channel Number
A 12345678910111213141516171819202122232425
N
K
1 A A A A AAAAAAA AAAA
2 A A A A AAAAAAA AAAA
3 A A A A AAAAAAA AAAA
4 A A A A AAAAAAA AAAA
B Purpose Channel Number
A 12345678910111213141516171819202122232425
N
K
1 Basic BC A AAAADDDDDDDD DDDD
2 Extend BC A AAAAADAADAAADDDD
3 All CTV BC A AAAAADAADAAAADAA
4 Other BC A AAAAAAAAAAAA AAAA
ADDING / DELETING CHANNELS
It is best to do ADD / DEL customizing before doing “BLNK.”
AUTO PROGRAM enters the same channels in banks 1, 2, 3,
and 4.
AUTO PROGRAM removes any channels previously customized
with ADD / DEL / BLNK. The channels available on your
antenna / cable will be entered, and any channels previously
entered but not currently available will be deleted.
ADD and DEL (not BLNK) can be used independently for channel banks 1, 2, 3, and 4.
A channel blanked, is blanked in all channel banks.
Channel allocations in tuning bands:
BROADCAST: 2 – 69
CABLE – CATV, HRC or ICC: 1 – 125
A = Active - - Channel was found during AUTO PROGRAM
A = Active Channel was found during AUTO PROGRAM
D = Deleted Channel was deleted using Add/ Del option.
BC = Blanked Channel Channel was blanked using BLANK channel option (ADD/DEL/BLNK).
Managing the Channel Banks
Examples of typical channel banks charts
Figure 1. Typical channel banks after running Auto Program
Figure 2. Typical channel banks after running Auto Program, and customizing with Add/Del/Blnk
PAGE 28
206-3852
PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies).
B Purpose Channel Number
A 12345678910111213141516171819202122232425
N
K
1
2
3
4
B Purpose Channel Number
A 26272829303132333435363738394041424344454647484950
N
K
1
2
3
4
B Purpose Channel Number
A 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 FM
N
K
1
2
3
4
B Purpose Channel Number
A 51525354555657585960616263646566676869707172737475
N
K
1
2
3
4
B Purpose Channel Number
A 767778798081828384858687888990919293949596979899100
N
K
1
2
3
4
Managing the Channel Banks
PAGE 29
206-3852
Installer’s Menus
Use the Installer Menu to set up or change operational settings
See descriptions of the Installer items on the following pages...
0IMCRMI038A 01.83 01
0-I. INST. SEQ. 0
SN: XXXX-XXXXXXXX
UPN: XXX-XXX-XXX-XXX
XX/XX/XX TE = 10110000
Accessing the Installer’s Menu
Installer’s menu items can be accessed by using the optional LP702 installer’s remote
control. Just press and hold MENU (about 8 seconds) until the display changes, then
press 9, 8, 7, 6, then ENTER. To exit the Installer’s Menu, press ENTER again. Any
changes you make will be stored in nonvolatile memory.
The Installer’s menu opens with item 0-I, INST. SEQ. Use the SELECT key to sequence
through the available menu items. Or, access an item directly by entering the line
number, then pressing MENU. For example, to access the Sleep Timer option which is
on line 15-I, press 15, then MENU. To change a setting use the Left/Right ADJ keys.
Using the Installer’s Menu
Items 0-I - 86-I are immediately accessible only upon entering the Installer’s Menu.
Their numbers, descriptions, ranges, factory default settings, and a place for listing
any changes made on-site are given below and on the following pages. A Factory
Menu that is intended for qualified service technicians only, is not shown. Normally
Factory menu items do not require adjustment.
Installer Menu Items 0-I through 25-I
XX-F Menu Items (Not
shown here) are servicetype adjustments and only
qualified technicians having
specialized test equipment
should access them.
Typical Installer Menu
Menu Item Function Value Range Default Value Brief Description of Function and Comments
0-I. INSTALLER SEQ 0 - 3 0 Leave default set 0.
1-I. POWER MANAGE 0 - 7 0 Sets number of hours of no activity before auto shutoff.
2-I. AC ON 0 / 1 0 Set to 1 to enable auto turn on at power up.
3-I. BAND/AFC 0 - 7 0 Tuning band, see detailed descriptions.
4-I. STRT CHANNEL 0 - 255 255 Channel at turn-on (Set 255 to go to last Channel viewed before turn-off).
5-I. CHAN LOCK 0 / 1 0 When set to 1, cannot tune from current channel.
6-I. GHOST CH 0 / 1 0 Set to 1 to enable Ghost Channel display.
7-I. START VOLUME 0 - 63, 255 255 Volume level at TV turn-on (Set 255 to retain last volume level).
8-I. MIN VOLUME 0 - 63 0 Minimum volume setting.
9-I. MAX VOLUME 0 - 63 63 Maximum volume setting.
10-I. MUTE DISABLE 0 / 1 0 Set to 1 to disable mute function.
11-I. KEY DEFEAT 0 / 1 1 Set to 1 to disable Menu, Select, and Adj keys on front panel.
12-I. IR BANKS EN. 0 / 1 0 Set to 1: enables TV to respond to IR codes to change Channel Bank directly.
13-I. SCAN MODE 0 / 1 0 Puts On-Off in Ch Up/Down sequence.
14-I. STRT CH IN SM 0 / 1 0 Set to 1 to put TV on/off below start channel number.
15-I. SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer.
16-I. EN. TIMER 0 / 1 1 Set to 1 to enable Timer.
17-I. ALARM 0 / 1 1 Set to 1 to enable Alarm.
18-I. NOT USED
19-I. NOT USED
20-I. FEATURE LEVEL 0 / 1 1 Zen 1 Leave default set 1 (1 Zen 1)
21-I. V-CHIP 0 / 1 1 Set to 1 to enable V-Chip.
22-I. MAX BLK HRS 0 - 99 12 Select number of Parental Control blocking hours.
23-I. CAPTION LOCK 0 / 1 0 Set to 1 to retain Caption setting at turn off.
24-I. TEXT MODE 0 / 1 1 Set to 1 to add Text option to closed caption menu.
25-I. FUNCTION PRE. 0 - 3 0 Controls channel preview in Pay-Per-View function menu.
PAGE 30
206-3852
Installer Menus
Menu Item Function Value Range Default Value Brief Description of Function and Comments
26-I. NOT USED
27-I. NOT USED
28-I. CH. OVER RIDE 0 / 1 1 When set to 0, limits direct access to favorite channels.
29-I. OLD OCV 0 / 1 0 OCV should set to 1.
30-I. ACK MASK 0 / 1 0 M.P.I. communication parameter.
31-I. POLL RATE 20 - 169 94 M.P.I. communication parameter.
32-I. TIMING PULSE 186 - 227 207 M.P.I. communication parameter.
33-I. NOT USED
34-I. CAMPORT EN. 0 / 1 1 Set to 1 to enable the front AUX (Camport) input.
35-I. NOT USED
36-I. NOT USED
37-I. REAR Y/C EN. 0 / 1 1 Set to 1 to enable the rear S-Video input.
38-I. NOT USED
39-I. NOT USED
40-I. AUTO CAMPORT 0 / 1 1 Set to 1 to automatically switch to Camport.
41-I. NOT USED
42-I. NOT USED
43-I. AUTO REAR Y/C 0 / 1 0 Set to 1 to automatically switch to rear S-Video input.
44-I. NOT USED
45-I. NOT USED
46-I. STRT AUX SRCE 0 - 2, 255 255 Set the starting AUX source
47-I. AUX STATUS 0 / 1 0 Set to 1 for M.P.I. AUX source reported as Channel number instead of Channel 0.
48-I. DIS. SETUP M. 0 / 1 0 Set to 1 to disable Setup menu.
49-I. DIS. AUDIO M. 0 / 1 0 Set to 1 to disable Audio menu.
50-I. DIS. VIDEO M. 0 / 1 0 Set to 1 to disable Video menu.
51-I. DIS. VCHIP M. 0 / 1 0 Set to 1 to disable V-Chip (Parental Control) menu.
52-I. DIS. SOURCE M. 0 / 1 0 Set to 1 to disable Source menu.
53-I. DIS. CH-TIME M. 0 / 1 0 Set to 1 to disable Channel-Time display.
54-I. EN. SET. COL. 0 / 1 0 Set to 1 to enable custom color for Setup menu.
55-I. FOR. SETUP M. 0 - 7 6 Custom foreground color for the Setup menu.
56-I. BCK. SETUP M. 0 - 7 4 Custom background color for the Setup menu.
57-I. EN. AUDIO COL. 0 / 1 0 Set to 1 to enable custom color for the Audio menu.
58-I. FOR. AUDIO M. 0 - 7 1 Custom foreground color for the Audio menu.
59-I. BCK AUDIO M. 0 - 7 7 Custom background color for the Audio menu.
60-I. EN. VIDEO COL. 0 / 1 0 Set to 1 to enable custom color for the Video menu.
61-I. FOR. VIDEO M. 0 - 7 4 Custom foreground color for the Video menu.
62-I. BCK VIDEO M. 0 - 7 7 Custom background color for the Video menu.
63-I. EN. PTL. COL. 0 / 1 0 Set to 1 to enable custom color for the V-Chip (Parental Control) menu.
Installer Menu Items 26-I through 63-I
PAGE 31
206-3852
Installer Menus
Menu Item Function Value Range Default Value Brief Description of Function and Comments
64-I. FOR. PTL. M. 0 - 7 6 Custom foreground color for the V-Chip (Parental Control) menu.
65-I. BCK. PTL. M. 0 - 7 4 Custom background color for the V-Chip (Parental Control) menu.
66-I. EN. SRC. COL. 0 / 1 0 Set to 1 to enable custom color for the Source menu.
67-I. FOR. SRC. M. 0 - 7 3 Custom foreground color for the Source menu.
68-I. BCK. SRC. M. 0 - 7 4 Custom background color for the Source menu.
69-I. EN. CH-T COL. 0 / 1 1 Set to 1 to enable custom color for the Channel-Time display.
70-I. FOR. CH-T COL 0 - 7 1 Custom foreground color for the Channel-Time display.
71-I. BCK. CH-T COL 0 - 7 1 Custom background color for the Channel-Time display.
72-I. NOT USED
73-I. CH NOT AVBLE 0 / 1 0 When set to 1 and channel override is 0, “NOT AVAILABLE” message is displayed
when direct accessing a channel not in the favorite channel list.
74-I. CH-TIME SIZE 0 / 1 0 When set to 1 and transparent background is selected for Channel-Time display,
(foreground color = background color and custom color enabled) a large channel
number is displayed instead of the normal Channel-Time display.
75-I. NOT USED
76-I. DEFEAT XDS 0 / 1 0 When set to 1, XDS display program information will not appear.
77-I. NOT USED
78-I. UPN MSB 0 - 255 255 User programmable number, most significant byte. (Line - Day)
79-I. UPN MSB-1 0 - 255 255 User programmable number, most significant byte - 1. (Week)
80-I. UPN MSB-2 0 - 255 255 User programmable number, most significant byte - 2. (SN-HIGH)
81-I. UPN LSB 0 - 255 255 User programmable number, least significant byte. (SN-LOW)
82-I. CHKSM ERROR 0 / 1 0 Enforces rigid M.P.I.* checksum.
83-I. HANDSHK TIME 0 - 5 0 Relaxes M.P.I. timing to be compatible with PC based Windows controlled systems.
84-I. PERMANENT BLK 0 / 1 0 Remove block hours setting for Parental Control and make blocks permanent.
85-I. A. MUTE TIME 0 - 254 50 Controls muting audio delay time when switching between AUX sources.
86-I. V. MUTE TIME 0 - 254 50 Controls muting video delay time when switching between AUX sources.
Detailed Descriptions of Installer Menu Items
0-I. INSTALLER SEQUENCE
Gives access to Installer Menu depending on the code selected.
0 = 9876 1 = 4321
2 = 1478 3 = 3698
1-I. POWER MANAGE (Power Management)
Determines hours of no activity before automatic shutoff. The
POWER MANAGE function is for saving energy. When set to 0,
Power Manage is OFF. Settings range from 0 - 7, with 1 - 7 repre-
senting the hours that the TV will remain on, unless there has
been activity from either the control panel or remote control.
2-I. AC ON (AC Power Switchable)
Allows the TV to turn ON just by applying AC power. Pressing the
ON button is not necessary. This is desirable when the TV is
plugged into a cable box or a power outlet controlled by a wall
switch. Use ADJUST to select 0 or 1, where 0 is the default is
OFF, and 1 is ON.
NOTE: When set to 1 (ON), the TV does not respond to ON/OFF
commands from either the remote or the control panel, and the
SLEEP TIMER is also nonfunctional.
Installer Menu Items 64-I through 86-I
*M.P.I. Multiple Protocol Input: Zenith protocol for remote control of TV through RJ11 (M.P.I.) jack on TV connections panel.
PAGE 32
206-3852
Installer Menus
3-I. BAND/AFC (Band/Automatic Frequency Control)
There are 8 possible settings for this option:
0 = Broadcast Fixed 4 = Broadcast AFC
5 = CATV Fixed 1 = CATV AFC
6 = HRC Fixed 2 = HRC AFC
7 = ICC Fixed 3 = ICC AFC
Channels are accessed faster when fixed modes are used. The AFC
(search modes) should only be used when some channels are not
on nominal frequencies.
NOTE: BAND is automatically set by AUTO PROGRAM.
If some channels were not found by AUTO PROGRAM, select the
appropriate AFC setting here and add the channels using the
ADD/DEL option in the Setup Menu.
4-I. STRT CHANNEL
When active, this function allows you to determine the initial
channel number when the TV is turned ON. This feature is useful
for an in-house information channel, since the TV would always
select that channel when it is turned on. Setting this to 255 causes the last channel viewed when TV was turned off to be the
tuned to channel when the TV is turned on again.
The range of values is 0 - 255. Use (adjust) keys to choose numbers that determine the start channel.
5-I. CHAN LOCK (Channel Lock)
CHAN LOCK is ideal if a cable box (or similar) is the sole source
for programming—and the TV must always be on the same channel. Changing channels with Channel Up/Down or keypad numbers
is impossible. Channel Lock is inactive when set to 0 (default).
Generally, this feature is used in conjunction with START CHANNEL
(item 4-I.) where the start channel may, for example, be set to 3
or 4. If the start channel is 3 then the TV will remain on channel
3. NOTE: When CHANNEL LOCK is active and CHANNEL OVERIDE is
disabled, AUTO PROGRAM is not active.
6-I. GHOST CH (Ghost Channel)
When set to 1, the current channel number is displayed in the
upper right corner of the CRT. The number moves slightly to prevent damage to the screen. The default is “0” or OFF.
NOTE: When captions are on, the “Ghost Channel” is not
displayed.
7-I. START VOLUME
This function allows the Installer to determine the initial volume
level setting when the TV is turned ON. This feature is useful for
an in-house information channel, since the TV would always select
that volume level when it is turned on. The range of values are 0 63, 255. If 255 is selected, the current volume level will be
retained in memory when the TV is turned off; at TV turn on, volume level is automatically set to the previous or last level.
8-I. MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable
with the VOLUME (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The range is
from 0 to 63—change values with ADJUST. The factory default is
0, which provides full range of volume control. It may be best to
set the same value on every TV.
NOTE: The minimum volume level cannot have a value setting
higher than in the MAX VOLUME level (described below).
9-I. MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allowable
with the VOLUME VOL Up/Down control. In this way, for example,
someone cannot set the volume level high enough to disturb others. The range is 0 to 63, with 63 as the default which gives the
user the full range of volume control. Change values with ADJUST
keys. It may be best to set the same value on every TV.
NOTE: The maximum volume level cannot have a value setting
lower than the MIN VOLUME level (described above).
10-I. MUTE DISABLE
Enables or disables sound mute function. Set to 1, sound cannot
be muted. Set to 0, sound can be muted.
11-I. KEY DEFEAT (Keyboard Defeat)
When set to 1, it prevents the end user from accessing screen
menus on the front panel—MENU, SELECT, and ADJUST do not
function. When set to 0, those keys are functional. The menus can
always be accessed with MENU on the remote.
12-I. IR BANKS EN.
For direct access to a particular Channel Bank. When enabled,
installer can access a channel bank by inputting the IR code for
the bank.
13-I. SCAN MODE
Allows variation in setting the On/Off with Channel UP/DOWN. You
may opt for TV channels only; TV channels + Off/ON with these
settings for Scan Mode:
Installer Menu Items 3-I through 13-I: Detailed Descriptions
PAGE 33
206-3852
Installer Menus
Scan mode Characteristics
0 Channel up/down keys change channels only.
1 Channel down below the lowest channel (or
channel up higher than the highest) and TV
turns off.
14-I. STRT CH IN SM
When set to 1, installs TV on/off event below the start channel at
TV turn on.
15-I. SLEEP TIMER
When set to 1, the SLEEP TIMER feature may be used (but no message is displayed prior to turn-off). When set to 0, the sleep timer
is not available.
16-I. EN. TIMER
Set to 1, timer function is available to user. Set to 0 to disable
Timer functions. (Clock must be set in order to use Timers.)
17-I. ALARM
Gives you the option of making the alarm function available to
the user. Set to 1, alarm function is available to user. Set to 0 to
disable the Alarm function.
Note: Clock must be set in order to set the Alarm.
18-I. NOT USED
19-I. NOT USED
20-I. FEATURE LEVEL
Default set to ZEN 1 for Zenith IR remote control operation.
Set O, P LBL for Zenith Private Label IR remote control operation.
Warning: Do not set to “0” or remote will not control TV.
21-I. V-CHIP
Set to 1 to activate V-Chip (Parental Control); have it available to
user to filter, control, or restrict programming content. Set to 0 to
turn V-Chip feature off, not available to user; no programming
restrictions can be set.
22-I. MAX BLK HRS
Set to 0 to 99 for the maximum V-Chip (Parental Control) block
hours. Default is 12 blocking hours.
23-I. CAPTION LOCK
Set to 1 to restore previous caption On/Off state after TV turns
off. When set to 0, captions are always off, when TV is initially
turned on.
24-I. TEXT MODE
Determines whether TEXT 1, TEXT 2, TEXT 3, or TEXT 4 decoding is
enabled when TEXT is turned on (either from the Setup Menu or
directly with CC on the remote).
TIP: Set Text Mode to 1 only if text is offered in your video
system.
25-I. FUNCTION PRE.
Set to 0 to suppress CHANNEL PREVIEW from the FUNCTION menu
with some Pay-Per-View systems.
26-I. NOT USED
27-I. NOT USED
28-I. CH. OVERRIDE (Channel Override)
When set to 1, the user can select channels with either Channel
Up/Down or by direct keypad entry. When set to 0, only those
channels that are entered for scanning may be selected by direct
keypad entry. Note: If set to 0, Auto Program is locked; (as shown
on Setup menu) you cannot do a channel search.
29-I. OLD OCV (On Command Video
TM
)
Set to 1 for operation with systems from On Command
Corporation.
30-I. ACK MASK
M.P.I. Communication Parameter. Leave at default setting unless
changed by Pay-Per-View provider.
31-I. POLL RATE
M.P.I. Communication Parameter. Leave at default setting unless
changed by Pay-Per-View provider.
32-I. TIMING PULSE
M.P.I. Communication Parameter. Leave at default setting unless
changed by Pay-Per-View provider.
33-I. NOT USED
34-I. FRONT AUX ENABLE
Set to 1 to enable the front AUX (Camport) input.
Set to 0 to disable front AUX input.
Installer should leave item
0-I FEATURE LEVEL set to
1 (default).
Installer Menu Items 14-I through 34-I: Detailed Descriptions
PAGE 34
206-3852
Installer Menus
35-I. NOT USED
36-I. NOT USED
37-I. REAR Y/C EN.
Set to 1 to enable the rear S-Video input.
Set to 0 to disable the rear S-Video input.
38-I. NOT USED
39-I. NOT USED
40-I. AUTO CAMPORT
Set to 1 to automatically switch to camport when equipment is
connected to front Video input.
Set to 0 to disable front Video automatic source selection.
41-I. NOT USED
42-I. NOT USED
43-I. AUTO REAR Y/C
Set to 1 to automatically switch viewing source to rear S-Video
input when equipment is connected.
Set to 0 to disable rear S-Video automatic source selection.
44-I. NOT USED
45-I. NOT USED
46-I. STRT AUX SRCE
Sets the starting AUX source.
47-I. AUX STATUS
Set to 1 for M.P.I. AUX source to be reported as a channel number
instead of channel 0. Set to 0 to disable AUX identification
change.
48-I. DIS. SETUP M.
Set to 1 to disable the Setup menu. Setup menu will not appear.
Set to 0 to enable the Setup menu.
49-I. DIS. AUDIO M.
Set to 1 to disable the Audio menu. Audio menu will not appear.
Set to 0 to enable the Audio menu.
50-I. DIS. VIDEO M.
Set to 1 to disable the Video menu. Video menu will not appear.
Set to 0 to enable the Video menu.
51-I. DIS. VCHIP M.
Set to 1 to disable the Parental Control menu. Parental Control
menu will not appear.
Set to 0 to enable the Parental Control menu.
52-I. DIS. SOURCE M.
Set to 1 to disable the Source menu. Source menu will not appear.
Set to 0 to enable the Source menu.
53-I. DIS. CH-TIME M.
Set to 1 to disable the Channel-Time display. Channel-Time display
will not appear.
Set to 0 to enable the Channel-Time display.
54-I. EN. SET. COL.
Set to 1 to enable custom color settings for the Setup menu.
Set to 0 to disable custom color settings for the Setup menu.
55-I. FOR. SETUP M. (Setup Menu Foreground Color)
Set according to Color Chart.
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
56-I. BCK. SETUP M. (Setup Menu Background Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
57-I. EN. AUDIO. COL.
Set to 1 to enable custom color settings for the Audio menu.
Set to 0 to disable custom color settings for the Audio menu.
58-I. FOR. AUDIO. COL. (Audio Menu Foreground Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
59-I. BCK. AUDIO. COL. (Audio Menu Background Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
60-I. EN. VIDEO. COL.
Set to 1 to enable custom color settings for the Video menu.
Set to 0 to disable custom color settings for the Video menu.
Installer Menu Items 35-I through 60-I: Detailed Descriptions
PAGE 35
206-3852
Installer Menus
61-I. FOR. VIDEO M. (Video Menu Foreground Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
62-I. BCK. VIDEO. COL. (Video Menu Background Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
63-I. EN. PTL. COL.
Set to 1 to enable custom color settings for the V-Chip menu.
Set to 0 to disable custom color settings for the V-Chip menu.
64-I. FOR. PTL. M. (V-Chip Menu Foreground Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
65-I. BCK. PTL. M. (V-Chip Menu Background Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
66-I. EN. SRC. COL.
Set to 1 to enable custom color for the Source menu.
Set to 0 to disable custom color for the Source menu.
67-I. FOR. SRC. M. (Source Menu Foreground Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
68-I. BCK. SRC. M. (Source Menu Background Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet.
69-I. EN. CH-T COL.
Set to 1 to enable custom color for the Channel-Time display.
Set to 0 to disable custom color for the Channel-Time display.
70-I. FOR. CH-TIME (Channel-Time Display Foreground Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
Note: If foreground and background color are the same, menu
background is transparent.
71-I. BCK. CH-TIME (Channel-Time Display Background Color)
0 = Black 3 = Yellow 6 = Cyan
1 = Red 4 = Blue 7 = White
2 = Green 5 = Violet
Note: If foreground and background color are the same, menu
background is transparent.
72-I. NOT USED
73-I. CH NOT AVBLE
When set to 1 and channel override is set to 0, “NOT AVAILABLE”
message is displayed when direct accessing a channel not in the
favorite channel list.
74-I. CH-TIME SIZE
When set to 1 and transparent background is selected for ChannelTime display, (foreground color = background color and custom
color enabled) a large channel number is displayed instead of the
normal Channel-Time display
.
75-I. NOT USED
76-I. DEFEAT XDS
Set to 1 to disable XDS display. Set to 0 to enable XDS display.
77-I. NOT USED
78-I. UPN MSB
User programmable number, most significant byte readable by
M.P.I. command.
79-I. UPN MSB-1
User programmable number, most significant byte-1 readable by
M.P.I. command.
80-I. UPN MSB-2
User programmable number, most significant byte-2 readable by
M.P.I. command.
81-I. UPN LSB
User programmable number, least significant byte readable by
M.P.I. command.
82-I. CHKSM ERROR
Enforces rigid M.P.I. checksum validation.
Set to 1 for validation.
Set to 0 to turn off.
Installer Menu Items 61-I through 82-I: Detailed Descriptions
PAGE 36
206-3852
Installer Menus
83-I. HANDSHK TIME
Adds an additional delay to the handshake time which is 64 msec,
thus relaxing M.P.I. timing requirements to be compatible with PC
based Windows controlled systems, range is 0 - 5.
Set to 0 to retain standard 64 msec delay.
Set to 1 - 5 to increase @ 16 msec ea., the delay up to 144 msec.
84-I. PERMANENT BLK
Allows Parental Control blocking schemes to be permanent by
removing the blocking hours function.
Set to 1 to install Parental Control blocking restrictions permanently.
Set to 0 for user-specified hours control of blocking schemes.
85-I. A. MUTE TIME
Controls audio muting delay time when switching between AUX
sources. The audio will be muted for 16 msec times the value of
this setting.
86-I. V. MUTE TIME
Controls video muting delay time when switching between AUX
sources. The video will be muted for 16 msec times the value of
this setting.
Installer Menu Items 83-I through 86-I: Detailed Descriptions
PAGE 37
206-3490-O
LT2000 QuickSet II Programmer
A slow flashing green light indicates there is a problem with the communications between the TV and the programmer. In this
case, check for a damaged cable, poor contacts, or other connection troubles.
If the status indicator is red, the programmer batteries are low and should be replaced. Use 4 good-quality alkaline AA batteries.
Use the Zenith LT2000
QuickSet II “Clone”
Programmer to copy the
setup from a “Master” TV
then quickly transfer the
setup to duplicate TVs must be the same model
number as the master TV
The optional QuickSet II Clone Programmer (LT2000) allows custom setup and programming information to be quickly copied from a master TV into multiple identical television sets. Once learned from the master, setup data is retained in the LT2000 for future use.
When using the LT2000, cloning operations will go easier if the TV set is connected to a good quality signal and operating with a stable
picture displayed. To operate the LT2000, use the indicated keys on an HP602, LP702, or MBR3447 remote, or the front panel keys on
the TV receiver.
Clone Controlling TV Display
Before you begin...
• The “master TV” should be connected to a good, stable signal
from an over-the-air antenna or cable service and turned on.
• Teaching and Learning is only possible between identical model
Zenith TVs. (However, the Clone programmer can store 4 different
master TV setups.)
WARNING: Copying a blank or incorrect memory into a
TV will cause the TV to operate erratically or become
inoperable.
• Use a Zenith MBR Remote like the MBR3447 or the TV front
panel controls to operate Learning and Teaching menus.
• Make sure that the batteries in the Clone programmer are fresh.
• If the batteries are removed, the Clone Clock time will be lost.
• Decide if you want to set the time from the Clone programmer or
copy the time to the Clone programmer; from a TV which has the
clock set to the current time.
• Follow the connection diagrams above to connect the Clone to a
master TV and, after learning is complete, to another TV to “teach”
it the setup.
• Setting the time and transferring it to the Clone or another TV is
a separate procedure.
• Once a TV’s setup is copied to another TV, that TV needs to be
disconnected from power for about 5 seconds to activate the
newly copied setup.
• See Troubleshooting to solve problems.
A. Set Up a Master TV
Using a Zenith Multi-Brand remote like the MBR3447, set up a
“Master” TV with custom settings and features as described in the
master TV’s operating guide. The master TV’s Setup is what you will
copy to the Clone Programmer and transfer to TVs of the same
model so they will operate identically.
B. Connect Clone to Master TV
If there is a good connection, the “Clone has Control of TV” message will appear. (See menu above left.)
Learn Master TV
Typical MPI Connections
Teach Other TV
Typical MPI Connections
Antenna
TV Back
Antenna
TV Back
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REVISION XX
CLONE CLOCK = XX:XX
TV CLOCK = XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
RF Coaxial Wire
(75ohm)
Super
Port
TV Back Panel
(Expanded View)
ANTENNA
CABLE
M.P.I.
QuickSet II Programmer
LT2000
Clone
SPEAKER
OUT
VIDEO
AUDIO
IN
IN
®
RF Coaxial Wire
(75ohm)
Super
Port
TV Back Panel
(Expanded View)
ANTENNA
CABLE
M.P.I.
QuickSet II Programmer
Clone
SPEAKER
OUT
VIDEO
AUDIO
IN
IN
®
LT2000
PAGE 38
206-3490-O
Clone Selection Menu Choices
Typical Clone Programmer on-screen menus
C. Learn Setup from Master TV
Press 1 to select the “Learn From TV” option, then press ON/OFF,
POWER, or ENTER to go to the Memory Bank Selection Menu.
Pick the Memory ”Bank” (1, 2, 3, or 4) you want to store this
Master TV’s Setup in by pressing either Channel key repeatedly to
pick Memory 1, 2, 3, or 4. (If you choose a Memory “Bank” that
already has a master TV’s setup already in it, it will be overwritten
by this Master TV’s setup.) Once the Clone memory bank is selected, press ON/OFF, POWER, or ENTER. The Clone memory bank you
have selected will be shown. Press ON/OFF or POWER to begin
copying the master TV’s setup.
Ca. Set the Clock (Optional)
Set the time on the Master TV’s Clock. (If the time has already
been copied from another TV into the Clone programmer, you can
set the Master TV’s clock by copying the time from the Clone programmer.) The Clone Programmer can copy the current time to
both a master TV and to the Clone’s internal clock; accurate to
within one minute. (Another reason that the Clone programmer
should be equipped with fresh, high-quality alkaline batteries is
for it to keep the time as accurately as possible.)
Since the Clone Programmer’s time cannot be set directly, the time
needs to be copied from a Zenith TV equipped with M.P.I. input
capability.
Once the time is copied to the Clone programmer, the current time
can then be transferred to another TV. (This can be a Master TV, or
another TV which has had the features already set up.)
D. Teach Master TV’s Setup to Other TV
Once Learning is complete, remove the M.P.I. cable from the master TV and connect it to the TV that you want to copy the master
TV’s setup to. With the “TV is Controlled by Clone” message displayed, press 2 or use either Channel key to go to the “Teach to
TV” option, press ON/OFF, POWER, or ENTER. Follow on-screen
instructions to transfer the Setup and other information to the
“Learning” TV. After the “Teach to TV is Complete” message is displayed, press any key to return to the Clone menus option, then
press ON/OFF, POWER, or ENTER. If finished, remove M.P.I. cable
from the TV.
E. Disconnect TV Power for 5 Seconds
Remove the TV power cord of the newly “Cloned TV” from the
power outlet for about 5 seconds to activate the newly copied
setup.
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REVISION XX
CLONE CLOCK= XX:XX
TV CLOCK= XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
-TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
-TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER
PAGE 39
206-3490-O
Clone Selection Menu Choices
Operation Notes
Disconnect the Clone from the TV when you are finished; automatically switching it off. The real-time clock continues to run
when the main circuits are switched off.
Reset Clone After Static Shock
After replacing exhausted batteries, or if the programmer
behaves strangely after a static shock, use a paper clip or similar
instrument inserted through the small hole marked ”RESET” to
activate the internal reset switch and restore normal operation.
After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV containing
the correct time.
The LT2000 programmer is designed to be used with TVs containing the 221-01006 and later processors. Usage with earlier TV
sets may give unpredictable results. The specific microprocessor
used in any TV set can be determined by activating the Installer
Menu. The microprocessor part number appears at the top of the
screen when the Installer Menu is activated. Processors before
the 221-01006-04 have a limited screen display capability. They
cannot display entire screens as shown in the quick setup
instructions accompanying the LT2000 clone programmer. Use the
printed menu illustrations on the quick setup sheet supplied with
the Clone as an aid to making your programming choices.
(Although the menus are not all displayed, the clone functions
all operate normally.)
When cloning operations are complete, just unplug the LT2000 from the TV.
If the TV does not display a picture (blank screen) after a few seconds, just change channels.
Troubleshooting
Problem Possible Cause(s) Possible Solution(s)
Clone Programmer
LED does not blink. • M.P.I. cord not connected. -Connect M.P.I. cord.
• TV not turned on. -TV must be on for clone to work.
• Weak batteries. -Install 4 fresh AA high-quality alkaline batteries.
Clone menu hard • Weak signal. -Connect TV to a reliable signal source.
to read.
No time set. • No time on master TV. -Set time on master TV, copy time to Clone Programmer.
Menu items 7-8 not • Not necessary. -Channel Labels already cloned; if they were on master TV.
on clone selection menu.
Master and Other TVs
Cloning did not work. • Procedure interrupted. -Wait until procedure complete message is displayed.
• Different TV models. -Cloning is only possible with identical model TVs.
Clone time disappeared. • Batteries were removed. -Batteries must remain installed to retain time settings.
Channel Labels not • Saved to other memory. -Must save channel labels to same memory bank as
present on cloned TV. master TV setup.
New Setup not present. • TV not reset. -Disconnect newly cloned TV from power for 5 seconds.
PAGE 40
206-3490-O
Parental Control Menu
Mini glossary
MOTION PICTURE ASSOCIATION OF AMERICA (MPAA) RATING SYSTEM
G General Audiences Content not offensive to most viewers.
PG Parental Guidance Content is such that parents may not want their children to view the program.
Suggested
PG-13 Parental Guidance Program is inappropriate for preteens, with a greater degree of offensive material
Suggested than a PG rated program.
R Restricted viewing Not for children under age 17. Strong elements of sex and/or violence.
NC-17 Restricted Viewing Not for children under age 17 under any circumstances. Strong sexual content.
X Hard Core Films Same as NC-17 rating.
Note: Zenith Electronics Corporation is not liable for any program content that appears when using this rating system; as always, user
discretion is advised.
Overview
To insure complete coverage for all TV programs, (movies and regular TV shows) choose a rating for MPAA, from the selections below AND choose ratings from the TV Parental Guidelines Rating System on the next page, using the Age Block
option for General Audiences, and for Children. In addition to those, you may wish to add additional restrictions from the
Content Block menu. See the Parental Control menu, and submenus example on the next page.
Things to Consider before Setting Up Parental Control
Determine which rating you consider acceptable to the viewer. (For example, if you choose TV-PG, all more restrictive ratings will be automatically blocked; the viewer will not be able to see: TV-PG, TV-14, or TV-MA rated programming.)
Do you want to block the auxiliary video source entirely? (Blocks the signal sent by the equipment, such as a VCR, connected to the TV Audio/Video input jacks; in the Aux. Block option.) Or leave unblocked, then choose allowable ratings.
Block program “Content” based on individual parameters such as: Strong Dialog, Mature Language, Sex Scenes, Violence
Scenes, or Fantasy Violence Scenes; in the Content Blk option.
How many hours do you want Parental Control to be active? You can set the Hours option for up to 99 hours.
Select a secret password; in the Set Password option. Use the number keys on the remote. Don’t forget the password, it is
the only way you can access the Parental Control menu and change rating selections, or turn Parental Control off.
Do you want Parental Control to be active all the time? If not, you can turn it on or off; with the Lock On/Off option.
This optional feature can be used to “block” undesirable programming from appearing on your TV.
You can set different Parental Control viewing restrictions for general audiences and for children - - both
can be active at the same time
.
Simply specifying one content block such as Sex
Scenes, will not automatically block another content
in the programs from appearing.
This TV offers the user a wide variety of options and settings that restrict or “block” the programming that can appear on
the TV. Parental control allows the user the capability of defining which program rating they consider acceptable, to the
younger or more sensitive viewer. It can be preset and turned either on or off by the user who specifies the secret 4-number code, the password. The number of hours blocked are specified. General audience and children viewer blocks can both
be programmed into the TV’s memory. Viewer ratings are specified for both TV and the motion picture industry; both rating systems can be used. The ratings are based mainly on the ages of children.
When the Aux input is set to block, your TV will block all programming you have set for cable or over-air broadcasts.
You cannot disable Parental Control by disconnecting the TV
from power. Block hours will automatically reset to the original
block time setting specified if power is disconnected.
PAGE 41
206-3490-O
Parental Control Menu
Mini glossary
TV PARENTAL GUIDELINE RATING SYSTEM
TV-G General Audience Considered suitable for all audiences; children may watch unattended.
TV-PG Parental Guidance Suggested Unsuitable for younger children, may contain: Suggestive Dialog, Mature Language, Sex, and Violence Scenes.
TV-14 Parents Strongly Cautioned Unsuitable for children under 14, may contain: Strong Dialog, Mature Language, Sex, and Violence Scenes.
TV-MA Mature Audience Only Adults only, may contain: Strong Dialog, Mature Language, Sex, and Violence Scenes.
CHILDREN’S CLASSIFICATIONS
TV-Y Children Considered suitable for all children under 7 years old.
TV-Y7 Children 7 and over Considered suitable for children over 7, may contain Fantasy Violence Scenes.
Press CH PREVIEW.
Use CHANNEL Up/Down to highlight PARENTAL CONTROL.
Press ADJ Right arrow to go to Parental Control menu.
Use SELECT to highlight an option like CONTENT BLOCK.
Press ADJ Right arrow to go to the CONTENT BLOCK menu.
Use SELECT to highlight an option like SEX SCENES.
Press ADJ Right arrow to choose: Unblocked, TV-PG AND
ABOVE, TV-14 AND ABOVE, or TV-MA. (AND ABOVE means
more restrictive headings are automatically included when
you choose a low restriction setting like TV-PG.) See the Mini
Glossary, Ratings Charts on this and the previous page for
rating meanings.
After you have selected and adjusted the parental control
menu options to your preferences:
- Set the number of hours Parental Control will be on.
- Set a 4-number password, using the number keypad.
- Set the Lock On/Off option to either On or Off.
Note: some broadcasts do not contain rating information.
After you have read the preceding page, follow instructions below to set up and activate Parental Control
TO BLOCK
CHANNEL PREVIEW
5 - - - 9 - - - 20 - - - 32 - - - 44 - - - AUX - - - -
CONTENT BLOCK
DIALOG
LANGUAGE
SEX SCENES
VIOLENCE
F VIOLENCE
NO RATING
TV-MA
CC FOR PARENTAL CONTROL
CH TO SELECT, ENTER TO QUIT
PRESS CC TO RETURN
TIMER
CH PREVIEW
ENTER
1
2
3
4
5
6
7
8
9
0
POWER
FLSHBK
MUTE
VOL
UME
CHANNEL
TV/FM
CC
MENU
ALARM
ADJ
ADJ
SELECT
4/6
3/5/7
1
1
2
3
4
2
5
6
7
8
PAGE 42
206-3490-O
Parental Control Menu
Unblocked
Blocked
General
Children
Unblocked
G and Above
PG and Above
PG-13 and Above
R and Above
NC-17 and Above
X
Dialog
Language
Sex Scenes
Violence
F Violence
No Rating
TO BLOCK
Unblocked
TV-PG and Above
TV-14 and Above
TV-MA
Unblocked
TV-Y7
Unblocked
Blocked
Unblocked
TV-G and Above
TV-PG and Above
TV-14 and Above
TV-MA
Unblocked
TV-Y and Above
TV-Y7
00 Hours
To Set
Enter Code: - - - -
On
Off
SETUP MENU
DIALOG
LANGUAGE
SEX SCENES
VIOLENCE
F VIOLENCE
NO RATING
TO BLOCK
GENERAL
CHILDREN
AGE BLOCK
UNBLOCKED
CONTENT BLOCK
TO BLOCK
AUX SOURCES
MPAA RATING
AGE BLOCK
CONTENT BLK
SET HOURS
SET PASSWORD
LOCK ON OFF
PARENTAL CONTROL
VIDEO MENU
PRESS CC TO RETURN
PRESS CC TO RETURN
UNBLOCKED
Typical Parental Control Menu Structure
PAGE 43
206-3490-O
Menus & On-Screen Displays
SLEEP TIMER
OFF
PRESS TIMER
Volume Display
Press VOLUME. Shows currently
selected sound setting.
Closed Captions Menu
Press CC. Turns Caption/Text option
On and Off.
PRESS DIGITS TO SET TIME
TIMER TO SELECT AM/PM
ALARM MENU
TIME NOW 3:11 PM
6:10 AM
TIMER
Alarm Menu
Press ALARM. Sets the time the TV
will automatically turn itself on.
CHANNEL PREVIEW
5 - - - 9 - - - 20 - - - 32 - - - 44 - - - AUX - - - -
CC FOR PARENTAL CONTROL
CH TO SELECT, ENTER TO QUIT
VOLUME
CAPTION 1 IS ON
CC
Press the remote keys indicated below to access these menus and displays
Ch 25 - PBS
7:15
OLD TIME MOVIES
LENGTH 01:00 TIME LEFT 00:36
Rating:
TV-14
PM
Channel/Time Display
Press ENTER. Shows currently
selected channel or source, current
time if the clock has been set,
incoming audio signal, and XDS
data if provided by broadcaster.
Sleep Timer Menu
Press TIMER. Shows remaining time
before TV shutoff. Choose a preset
time for TV turn-off.
Ch Preview Menu
Press CH PREV. Displays list of the
available TV Channels, Guest
Parental Control menu, also used to
select Auxiliary input source.
PAGE 44
206-3490-O
Routine TV cabinet and screen cleaning
Maintenance
1. Here’s a great way to keep the dust off the screen for a while. Wet a soft cloth in a mixture of lukewarm water
and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to
wipe the screen.
2. Make sure the excess water is off the screen, and then let it air-dry before turning it on.
1. Use a soft cloth with a mild soap solution to wipe the cabinet. (Avoid using any harsh, industrial strength variety of cleaner.)
2. Rinse the cloth and wipe the cabinet again.
3. Let the cabinet air-dry before turning the Concierge TV on.
Use a quality wood cleaner and polish. This will protect the TV from dirt and dust, as well as keep the cabinet
looking new.
If the TV is to be left dormant for a long time, it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. If you use an off-air antenna, you may also want to disconnect it from
the back of the TV.
Screen Cleaning
Extended Absence
If you unplug the TV, you may have to reset the clock using the Clock Set menu described earlier.
See page 18.
Cabinet Cleaning
Wood Cabinet
Careful and regular cleaning can extend the the useful service life of the TV. Be sure to turn the power off and pull out
the plug before you begin any cleaning.
PAGE 45
206-3490-O
SYMPTOM
Snowy picture and unclear sound.
Multiple images or ‘ghost shadows.’
Interference: Sharp lines across
the screen and poor sound.
Normal picture but no sound.
No picture and unclear sound.
No picture and no sound.
No color, but the sound is O.K.
Picture has a big black box
on it, but the sound is O.K.
Remote control doesn’t work.
Menu options can’t be
changed or selected.
No picture or sound when any
non-cable source is selected.
No XDS Information.
Troubleshooting
POSSIBLE SOLUTIONS
• Check antenna connection or location
• Check cable input.
• Check to see if the TV/VCR button on VCR has the TV selected
• Check antenna direction and/or location.
• Check cable input
• Make sure the wire from the antenna to the TV is
properly connected.
The following may cause image problems or distortion:
Electrical appliances, powerful lights, cars, trucks; computers or
portable phones; medical equipment.
• If possible increase the distance between the The TV and
the offending appliance. Or shut one of them off.
• Check volume levels.
• Make sure the TV sound is not muted.
• Try another channel. The problem may be the broadcast, not the TV
• Are the Audio A/V cables properly installed?
• Are the wires for external speakers (if you have external speakers)
properly installed?
• If the audio mode is set to SAP, the channel may not have a SAP program.
• Are you in TV or cable tuning mode, and should be in the other?
• Make sure output channels on all A/V equipment are on the same channel (3 or 4).
• Check that all connections are tight.
• Is the AC power cord plugged in?
• Check that your AC power outlet works. (Test it by plugging in another device
or try another power outlet.)
• Make sure your brightness and audio controls are set properly.
• Try another channel. The problem may be with the broadcast.
• Check the settings in the Video menu.
• Try another channel. The problem may be with the broadcast. Weak signal?
• Broadcast may be in black and white.
• The CC (closed caption) option may be in Text mode. Select Caption 1, or OFF
in the Captions/(Text) menu.
• Make sure the batteries are fresh and installed properly. Any obstructions?
• Make sure the batteries are fresh and installed properly.
• Try using front panel controls, remote control problem?
• Try unplugging the TV for a few minutes, then plug it back in.
• Check to see if the source equipment has been turned on.
• Make sure that the connections are secure on the TV and source equipment.
• XDS data is provided at the discretion of the broadcasting station. Not all
programs will have this information.
PAGE 46
206-3852
Glossary
A list of definitions for words found in this guide
.
75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a
wire sticking through the middle. It screws onto the threaded jack on the back of the TV.
300 TO 75 OHM A small device that connects a two-wire
300 ohm antenna to a 75 ohm RF jack.
ADAPTER They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on
the other end.
A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television).
ADD This function lets the installer add new channels to list that the guest will scroll through using the guest remote.
AMPLIFIER An electronic device that amplifies sound from a television, CD player, VCR, DVD, or other A/V device.
ANTENNA The physical receiver of television signals sent over the air. A large metal piece of equipment does not always have
to be visible to be using an antenna.
AUTO PROGRAM Auto Program has the Concierge TV automatically find all the channels available in the area.
DELETE Lets the installer remove channels from the list the guest will scroll through using the guest remote.
INPUT Refers to the jack that receives a signal from a TV, VCR or other A/V device.
JACK A connection on the back of a TV, VCR, or any other A/V device.
MONO SOUND Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio.
M.P.I. Multiple Protocol Interface: Zenith protocol for external control of TV through RJ11 (M.P.I.) input
jack on TV connections panel. (M.P.I. jack is used for cloning TV’s features.)
OUTPUT Refers to the jack that sends a signal out of a VCR, DVD, or other A/V device.
2ND AUDIO Second Audio Programming (SAP) is another, separate, audio channel
PROGRAMMING/SAP Available with some programming. Choosing SAP often refers to listening to audio in another language, such as
Spanish or French.
SIGNAL Picture and sound traveling through a cable, or over the air, to your television screen.
TUNER Device that receives audio/video signals and turns them into picture and sound.
XDS Extended Data Service: Additional program information provided at the discretion of the broadcaster.
PAGE 47
206-3490-O
Notes
206-3852
Issue*
Copyright 2003 Zenith Electronics Corporation
Your Zenith TV Warranty
For Customer Support/Service
Please call:
1-888-865-3026
www.zenith.com
Direct-View Color TV Welcome to the Zenith family! We believe that you will be pleased with your new Zenith TV. Please read this warranty carefully, it is a “LIMITED WAR-
RANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state
within the U.S.A.
ZENITH’S RESPONSIBILITY
Service Labor During a period of one year from effective warranty date, Zenith will provide service labor by a Zenith authorized service center when needed, as
determined by the Zenith service center, as a result of manufacturing defects.
Parts New or remanufactured replacements for factory-defective parts will be supplied by a Zenith authorized service center for one year from effective
warranty date (color picture tube — two years). Such replacement parts are warranted for the remaining portion of the original warranty period.
Warranty Service Warranty service is provided in the institution in most cases. (Some repairs may require the unit to be taken by the servicer to the repair facility and
returned, at no additional charge.) Call 1-888-865-3026 for further information.
Not Covered This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls, installation or repair of antenna systems,
cable converters or cable company-supplied equipment; it also does not cover damage due to misuse, abuse, negligence, acts of God or other causes
beyond the control of Zenith. Any alteration of the product after manufacture voids this warranty in its entirety.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ZENITH SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR
INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT. SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
OWNER’S RESPONSIBILITY
Effective Warranty Date Warranty begins on the date of installation of the Commercial Products Direct-View Television Receiver.
For your convenience, keep the dealer’s dated bill of sale or delivery ticket as evidence of the purchase date.
Operating Guide Read your Operating Guide carefully so that you will understand the operation of the TV and how to adjust the controls.
Antenna Reception problems caused by inadequate antenna or faulty antenna connections are the owner’s responsibility.
Warranty Service For warranty service information, call 1-888-865-3026. Parts and service labor that are Zenith’s responsibility (see above) will be provided without
charge. Other service is at the owner’s expense. If you have any problem in obtaining satisfactory warranty service, call 1-888-865-3026.
You must provide the model number, serial number and date of purchase or date of original installation.
Before you ask for warranty service, read “Maintenance and Troubleshooting” in the operating guide. You might avoid a service call.
3828VA0A30A
Loading...