Zenith DVD-2220 User Manual
machine numbers | DVD2250
operating guide / warranty
As an ENERGY STAR® Partner, Zenith Electronics
Corporation has determined that this product
meets the E
NERGY STAR® guidelines for energy
efficiency.
PAGE 2 INTRODUCTION
Safety Precautions
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated ‘dangerous voltage’ within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION:
POUR EVITER LES CHOCS ELECTRIQUE, INTRODUIRE LA LAME LAPLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LAPRISE ET POUSSER JUSQU’AU FOUD.
CAUTION: This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference, should the unit require maintenance, contact an authorized service location-see
service procedure.
Use of controls, adjustments or the performance of procedures other than those specified may
result herein hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation
when open the enclosure. DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connect
ed.
- Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
INDUSTRY CANADA REQUIREMENT :
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numéruque de la classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Zenith is a trademark of ZEC © Copyright Zenith Electronics Corporation 1999
RECORD YOUR MODEL NUMBER (Now, while you can see it)
The model and serial number of your new DVD
player are located on the back of the DVD player cabinet. For your future
convenience, we suggest that you record these numbers here:
MODEL NO.____________________________________
SERIAL NO.____________________________________
WARNING
RISK OF ELECTRIC SHICK
DO NOT OPEN
AVIS
WARNING : TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
RISQUE DE CHOC ELECTRIQUE NE
PAS OUVRIR
INTRODUCTION PAGE 3
Table of Contents
Introduction
❏ Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . 2
❏ Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . 3
❏ IMPORTANT SAFETY INSTRUCTIONS . . . . . . 4-5
❏ Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
❏ Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 7
❏ Identification of Controls . . . . . . . . . . . . . . . . . 8-12
Front Panel/Display window. . . . . . . . . . . . . . . . . . . . . 8
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Controlling the TVs . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Preparing the Remote Control . . . . . . . . . . . . . . . . . . 12
Operating with the Remote Control . . . . . . . . . . . . . . 12
Connections
❏ Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . 13
❏ Connecting to an Audio System . . . . . . . . . . . . . 14
❏ Connecting to Optional Equipment . . . . . . . . 15-17
Enjoying Dolby Digital (AC-3) Sound . . . . . . . . . . . . . 15
Enjoying Dolby Pro Logic Surround Sound . . . . . . . . 16
Enjoying 2 Channel Digital Stereo Sound. . . . . . . . . . 17
Enjoying DTS Sound. . . . . . . . . . . . . . . . . . . . . . . . . 17
Basic Operation
❏ Basic Playback . . . . . . . . . . . . . . . . . . . . . . . 18-22
Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-20
Playing at x2 Normal Speed or
Scanning at High Speed . . . . . . . . . . . . . . . . . . . . . . . 21
Playing Frame by Frame . . . . . . . . . . . . . . . . . . . . . . 21
Playing in Slow-Motion . . . . . . . . . . . . . . . . . . . . . . . 22
Resuming Playback from the Same Location. . . . . . . 22
Operation Using GUI Menu Icons
❏ General Information about GUI menu icons . . . . 23
❏ Detailed description of each GUI menu icon. . . . 24
Advanced Operation
❏ Using a title menu/DVD menu . . . . . . . . . . . . . . 25
❏ Changing subtitle language . . . . . . . . . . . . . . . . 26
❏ Changing audio soundtrack language. . . . . . . . . 27
❏ Viewing from another angle . . . . . . . . . . . . . . . . 28
❏ Producing a 3D Surround effect. . . . . . . . . . . . . 28
❏ Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
❏ Storing markers in memory to be
viewed (listened to) again. . . . . . . . . . . . . . . . . . 30
❏ Zooming Feature/Random Play . . . . . . . . . . . . . 31
❏ Program Play. . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Initial SETUP Operation
❏ Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
❏ Selecting disc Languages . . . . . . . . . . . . . . . . . 34
❏ Selecting rating level and password . . . . . . . 35-36
❏ Selecting TV Aspect. . . . . . . . . . . . . . . . . . . . . . 37
❏ Selecting Menu Language . . . . . . . . . . . . . . . . . 38
❏ Selecting Digital Audio Output . . . . . . . . . . . . . . 39
❏ Table of Languages and Their Abbreviations . . . 40
Reference
❏ Disc Requirements/Copyright Information. . . . . . 41
❏ Before Calling Service Personnel. . . . . . . . . . . . 42
❏ Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 43
PAGE 4 INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL
AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or
fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for
installation, use and servicing.
This unit is fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read owner ’s manual
After unpacking this product, read the owner’s
manual carefully, and follow all the operating and
other instructions.
2. Power Sources
This product should be operated only from the type
of power source indicated on the marking label. If
you are not sure of the type of power supply in your
home, consult your product dealer or local power
company. For products intended to operate from
battery power, or other sources, refer to the
operating instructions.
3. Grounding or Polarization
This product is equipped with a polarized alternating
current line plug (a plug having one blade wider than
the other). This plug will fit into the power outlet only
one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
4. Ventilation
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from overheating. These
openings must not be blocked or covered. The
openings should never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in
installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s
instructions have been adhered to.
5. Heat
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
6. Water and Moisture
Do not use this product near water-for example,
near a bath tub, wash bowl, kitchen sink. or laundry
tub; in a wet basement; or near a swimming pool
and the like.
7. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
8. Power-Cord Protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles,
and the point where they exit from the product.
9. Overloading
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result
in a risk of fire or electric shock.
10.Lightning
For added protection of this product during storms, or
when it is left unattended and unused for long
periods of time, unplug it from the wall outlet.
This will prevent damage to the product due to
lightning and power-line surges.
11.Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result in
a fire or electric shock. Never spill liquid of any kind
on the product.
12.Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
INTRODUCTION PAGE 5
IMPORTANT SAFETY INSTRUCTIONS
13.Accessories
Do not place this product on
an unstable cart, stand, tripod,
bracket, or table. The product
may fall, causing serious
injury to a child or adult, and
serious damage to the
product. Use only with a cart,
stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the
product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer. A product and cart combination should
be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product and
cart combination to overturn.
14.Disc Tray
Keep your fingers well clear of the disc tray as it is
closing. It may cause serious personal injury.
15.Burden
Do not place a heavy object on or step on the
product. The object may fall, causing serious
personal injury and serious damage to the product.
16.Connecting
When you connect the product to other equipment,
turn off the power and unplug all of the equipment
from the wall outlet. Failure to do so may cause an
electric shock and serious personal injury. Read the
owner’s manual of the other equipment carefully and
follow the instructions when making any
connections.
17.Sound Volume
Reduce the volume to the minimum level before you
turn on the product. Otherwise, sudden high volume
sound may cause hearing or speaker damage.
18.Sound Distortion
Do not allow the product to output distorted sound
for a longtime. It may cause speaker overheating
and fire.
19.Headphones
When you use the headphones, keep the volume at
a moderate level. If you use the headphones
continuously with high volume sound, it may cause
hearing damage.
20.Laser Beam
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of
the laser beam. It may cause sight damage.
21.Disc
Do not use a cracked, deformed, or repaired disc.
These discs are easily broken and may cause serious personal injury and product malfunction.
22.Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is
damaged.
b) If liquid has been spilled, or objects have fallen
into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e) If the product has been dropped or damaged in
any way.
f) When the product exhibits a distinct change in
performance-this indicates a need for service.
23.Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
24.Replacement parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.
25.Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in proper
operating condition.
PORTABLE CART WARNING
PAGE 6 INTRODUCTION
Precautions
❏
When shipping the DVD player, always use the
original shipping carton and packing materials.
For maximum protection, repack the unit as it was
originally packed at the factory.
❏
Do not use volatile liquids, such as insect spray, near
the DVD player. Do not leave rubber or plastic
products in contact with the DVD player for a long
time. They will leave marks on the finish.
❏
The top and rear panels of the DVD player may
become warm after a long period of use. This is
normal and not a malfunction.
❏
When the DVD player is not in use, be sure to
remove the disc and turn off the power.
❏
If you do not use the DVD player for a long period, the
unit may not function properly in the future. Turn on
and use the DVD player occasionally.
❏
When you place this DVD player near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, move the DVD
player away from the TV, radio, or VCR.
Use a soft, dry cloth for cleaning.
❏
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry. Do not use any type of solvent, such as thinner
and benzine, as they may damage the surface of the
DVD player.
❏
If you use a chemical saturated cloth to clean the
unit, follow that product’s instructions.
Warning: Cleaning and adjustment of lenses
and/or other components of playback mechanism
should be performed by a qualified service
technician.
The DVD player is a high technology, precision device. If
the optical pick-up lens and disc drive parts are dirty or
worn down, the picture quality becomes poor. To obtain
a clear picture, we recommend regular inspection and
maintenance (cleaning or parts replacement) every
1,000 hours of use depending on the operating
environment. For details, contact your nearest dealer.
Moisture condensation damages the DVD player.
Please read the following carefully.
Moisture condensation occurs, for example, when
you pour a cold drink into a glass on a warm day.
Drops of water form on the outside of the glass. In
the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the DVD player.
Moisture condensation occurs during the following
cases.
❏
When you bring the DVD player directly from a cold
place to a warm place.
❏
When you use the DVD player in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
❏
In summer, when you use the DVD player in a hot
and humid place just after you move the unit from
an air conditioned room.
❏
When you use the DVD player in a humid place.
❏
Do not use the DVD player when moisture
condensation may occur.
If you use the DVD player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the DVD player to the wall
outlet, turn on the DVD player and leave it “ON” for
two or three hours. After two or three hours, the
DVD player will have warmed up and evaporated
any moisture. Keep the DVD player connected to
the wall outlet and moisture condensation will
seldom occur.
Notes on handling
Notes on Locating
Notes on Cleaning
To Obtain a Clear Picture
Notes on Moisture Condensation
E
x
a
m
p
l
e
s
o
f
m
o
i
s
t
u
r
e
c
o
n
d
e
n
s
a
t
i
o
n
Optical
pick-up lens
It's too
warm
!
Wait!
INTRODUCTION PAGE 7
Notes on Discs
This section shows you how to handle, clean, and store discs.
On Handling Discs
❍
Do not touch the playback side of the disc.
❍
Do not attach paper or tape to discs.
On Storing Discs
❍
Do not store discs in a place subject to
direct sunlight or near heat sources.
❍
Do not store discs in places subject to
moisture and dust such as a bathroom or
near a humidifier.
❍
Store discs vertically in a case. Stacking or
placing objects on discs outside of their
case may cause warping.
On Cleaning Discs
❍
Fingerprints and dust on the disc cause
picture and sound deterioration. Wipe the
disc from the center outward with a soft
cloth. Always keep the disc clean.
❍
If you cannot wipe off the dust with a soft
cloth, wipe the disc lightly with a slightly
moistened soft cloth and finish with a dry
cloth.
❍
Do not use any type of solvents such as
thinner, benzine, commercially available
cleaners or anti-static spray for vinyl LPs.
They may damage the disc.
About This Owner’s Manual
❍
This owner’s manual explains the basic
instructions of this DVD player.
❍
Some DVD video discs have functions that
may not be explained in this owner’s manual.
Therefore, some instructions may differ from
this owner’s manual, and there may be extra
instructions. In this case, follow the instructions
displayed on the TV screen or package.
❍
“ ” may appear on the TV screen
during operation. This icon means the
function explained in this owner’s manual is
not available on that specific DVD video
disc.
PAGE 8 INTRODUCTION
Identification of Controls
Front Panel
Display Window
play
stop
pause/step
skip
select/entermenu
scan
open/closepower
DVD
TOTALCHP / TRK
TITLE PROG.
ALL A B RANDOM
CD
DVD indicator
CD indicator
RANDOM indicator
Repeat playback
mode indicators
Title number indicator
Chapter/track number indicator
Angle icon indicator
Operating status indicator
Total playing time/elapsed time indicators
OPEN/CLOSE button
POWER/Standby button
and indicator
(Power ON mode: Green color
Standby mode: Red color)
PLAY button
SKIP/SCAN buttons
MENU button
STOP button
Disc tray
PAUSE/STEP button
SELECT/ENTER button
Display window
ARROW
buttons
INTRODUCTION PAGE 9
Identification of Controls
Rear Panel
COAXIAL
OPTICAL
DIGITAL OUT
AUDIO OUT
COMPONENT
VIDEO OUT
Y
Pr
Pb
S-VIDEO
OUT
L
1 2
R
VIDEO
OUT
VIDEO OUT jack
S-VIDEO OUT jack
ANALOG AUDIO OUT(R/L) jacks 1, 2
POWER CORD
Connect to an AC 120V, 60Hz outlet only.
While plugged into an AC outlet, the DVD
consumes 3W of electrical power in OFF
condition.
COAXIAL DIGITAL
AUDIO OUT jack
OPTICAL DIGITAL AUDIO OUT jack
Remove the dust protection cap from the connector and
connect the optical digital cable (not supplied) firmly so that
the configurations of both the cable and the connector match.
Keep the dust protection cap and always reattach the cap
when not using the connector to protect against dust.
Dust protection cap
COMPONENT VIDEO OUT jacks
PAGE 10 INTRODUCTION
Identification of Controls (con’d)
REMOTE CONTROL
clear
program
display return/tv input
select
/enter
title menu
ch
ch
vol vol
audio subtitle sound/muteangle
setup repeat random
power
dvd tv
open/close
a-b
123
45
6
7
8
0
9
slow
zoom marker-search
pause/stepresume
s
c
a
n
s
k
i
p
stop
play
You will find instructions for each of the remote control functions in the appropriate sections of this
instruction manual.
POWER button
REPEAT button
SETUP button
SUBTITLE button
AUDIO button
TITLE button
SELECT/ENTER button
DISPLAY button
ZOOM button
FWD/REV SCAN button
STOP button
PAUSE/STEP button
RESUME button
Number buttons
CLEAR button
DVD/TV Selector Switch
OPEN/CLOSE button
A-B button
RANDOM button
ANGLE button
SOUND
(MUTE) button
*MENU buttons
** ARROW
(Volume/Channel)
buttons
RETURN
(TV INPUT) button
MARKER-SEARCH button
PLAY button
FWD/REV SKIP button
SLOW buttons
PROGRAM button
*MENU button
Use the MENU button to display the
menu screen included on DVD
video discs. To operate a menu
screen, follow the instructions in
“Using a DVD Menu” (page 25).
** Directional arrow buttons
(up, down, left, right) for use in
highlighting a selection on a GUI
menu screen, TITLE and MENU
screen.
***TITLE button
Use the TITLE button to display the
title screen included on DVD video
discs. To operate a menu screen,
follow the instructions in “Using a
Title Menu” (page 25).
INSTALLATION PAGE 11
Controlling the TVs
Set the DVD/TV selector to TV.
While holding PROGRAM button, press the
number buttons to set the code number
referring to the table on the below.
Some manufactures have more than one code number. If the
remote control does not operate with the VCR, CATV or TV
after setting the code number, try another number.
To control the TV
POWER, Number (0~9), SELECT (ENTER), RETURN (Input
select), CH (Channel)
E/D, VOL (Volume) E/D and SOUND
(MUTE) buttons on the remote control are activated.
❍ Due to the variety of codes used by manufactures, our company
cannot guarantee that the MBR remote control will operate with
every model of the brands listed.
1
2
Your remote control operates the common
features of most, but not all, models and
brands of IR (infrared) controlled TVs.
clear
program
123
45
6
7
8
0
9
setup repeat random
power
dvd tv
open/close
a-b
2
1
2
Note
TV Brand Name Codes
ADMIRAL 110, 113, 144, 151, 152
AKAI 115
AMARK 131
AOC 115
BELL & HOWELL 113
BROKSONIC 140, 143
CANDLE 158
CENTURION 130
CITIZEN 156, 157, 158, 159, 160, 161, 162
CORONADO 131
CROWN 131
CURTIS MATHES 113, 115, 118, 130, 144, 151
DAEWOO 145, 146, 147, 148, 149, 150
DAYTRON 115, 130
EMERSON 110, 111, 115, 131, 140, 143
FISHER 116, 125
FUNAI 153, 154
GENERAL ELECTRIC 102, 118, 127, 128, 133, 144, 151
HITACHI 119, 131, 132
JC PENNEY 102, 115, 124, 130, 133
JVC 109, 141
KMC 131
KTV 115, 130, 131, 138
LG (GOLDSTAR) 115, 122, 130, 131, 133, 146
LODGENET 113
LOGIK 113
LXI 104, 116, 123, 124, 125, 131, 139
MAGNAVOX 100, 106, 107, 109, 114, 115, 121, 122, 130,
131, 133, 158
MAJESTIC 113
MARANTZ 103, 115
MEMOREX 113
TV Brand Name Codes
MGA/MITSUBISHI 103, 114, 115, 130
MONTGOMERY WARD 103, 113, 114, 115, 121, 129, 130, 131, 139
NEC 115, 130
PANASONIC 104, 122, 127, 128, 133, 163
PHILCO 115, 121, 122, 130, 131, 150
PHILIPS 121, 122
PIONEER 134
PORTLAND 131
PROSCAN 118, 144, 151
QUASAR 127, 128
RADIO SHACK 110, 111, 129
RCA 115, 118, 144, 151
REALISTIC 110, 111, 129
SAMPO 130
SAMSUNG 104, 115, 130, 131
SANYO 116, 125
SCOTT 115, 130
SEARS 104, 116, 123, 124, 125, 131
SHARP 112, 129, 131, 139
SIGNATURE 2000 102, 113, 114, 115, 121, 129, 130, 131, 139
SONY 105
SOUNDESIGN 158
SYLVANIA 106, 107, 115, 121, 122, 130, 133, 158
SYMPHONIC 153, 154
TATUNG 128
TEKNIKA 110, 113, 122, 131, 158
TELERENT 113, 131
YORX 130
TOSHIBA 104, 123, 124
WARDS 102, 113, 114, 115, 121, 130, 131
XR1000 155
ZENITH 100, 101
Identification of Controls (con’d)
Insert the batteries into the remote control so you can
use it to operate the DVD player.
Open the battery cover.
Insert batteries (AAA size).
● Make sure to match the + and - on the batteries to
the marks inside the battery compartment.
Close the cover.
❍
Improper use of batteries may cause battery leakage and
corrosion.
❍
To operate the remote control correctly, follow the
instructions below.
❍
Do not insert the batteries into the remote control in the
wrong direction.
❍
Do not charge, heat, open, or short-circuit the batteries.
Do not throw the batteries into fire.
❍
Do not leave dead or exhausted batteries in the remote
control.
❍
Do not use different types of batteries together, or mix
old and new batteries.
❍
If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage
from battery corrosion.
❍
If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.
❍
If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.
❍
The batteries should last about one year with normal
use.
This section shows you how to use the remote control.
Point the remote control at the
remote sensor and press the
buttons.
Distance: About 23 ft (7 m) from the front of the remote
sensor
Angle: About 30° in each direction of the front of the
remote sensor
* Do not expose the remote sensor of the DVD
player to a strong light source such as direct
sunlight or illumination. If you do so, you may not
be able to operate the DVD player with the remote
control.
❍
Direct the remote control at the remote sensor of the
DVD player.
❍
Do not drop or give the remote control a shock.
❍
Do not leave the remote control near extremely hot or
humid place.
❍
Do not spill water or put anything wet on the remote
control.
❍
Do not open the remote control.
Preparing the Remote Control
Operating with the Remote Control
play
stop
pause/step
skip
select/entermenu
scan
open/closepower
30° 30°
Within about 23 ft (about 7 m)
Notes on batteries
Notes on the remote control
1
2
3
title menu
ch
audio subtitle sound/muteangle
setup repeat random
power
dvd tv
open/close
a-b
PAGE 12 INSTALLATION
CONNECTIONS PAGE 13
Connecting to a TV
Connect the DVD player to your TV
COAXIAL
OPTICAL
DIGITAL OUT
AUDIO OUT
COMPONENT
VIDEO OUT
Y
Pr
Pb
S-VIDEO
OUT
L
1 2
R
VIDEO
OUT
S-video cable
(supplied)
To S-VIDEO OUT
(white)
L
To COMPONENT
VIDEO OUT
To AUDIO/VIDEO OUT
Audio/Video cable
(supplied)
To video input
(yellow)
To audio inputs
(red and white)
Video cable (Y, Pb, Pr) (not supplied)
To S-video input
TV or monitor with
audio video inputs
(red)R(yellow)
V
❍
Refer to the owner’s manual of your TV as well.
❍
When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
❍
If your television set has one audio input, connect the DVD player to a Y cable adapter (not supplied) and then connect to your
TV.
❍
Connect the DVD player to your TV directly. If you connect the DVD player to a VCR, the playback picture will be
distorted because DVD video discs are copy protected.
Warning
Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the coaxial digital audio jack of
this DVD player to an AV decoder that has the Dolby Digital (AC-3) decoding function. High volume sound may damage your hearing as well as the speakers. (Refer to “Selecting Digital Audio Output” on page 39.)
Notes
If the TV has an S-video input, connect the DVD
player with the supplied S-video cable.
The component video connections supply component signals (Y, Pb, Pr) to video
equipment equipped with component video input connections. If your TV receiver has
component video inputs, it is highly recommended that you use a component video
cable (not supplied) to obtain the full benefit of DVD’s superb picture quality. (The
picture quality obtained using component video is even better than that of S-video.)
PAGE 14 CONNECTIONS
Connecting to an Audio System
You can listen to the sound of audio CDs and DVD video discs in stereo.
COAXIAL
OPTICAL
DIGITAL OUT
AUDIO OUT
COMPONENT
VIDEO OUT
Y
Pr
Pb
S-VIDEO
OUT
L
1 2
R
VIDEO
OUT
To audio inputs
of the amplifier
(white)
(red)
Audio system
To VIDEO
OUT
To AUDIO OUT
S-video cable (supplied)
To S-VIDEO OUT
(yellow)
(red)
R
(white)
L
To video input (yellow)
To S-video input
TV or monitor with
audio/video inputs
If the TV has an S-video input, connect the DVD
player with the supplied S-video cable.
❍
Refer to the owner’s manual of your audio system as well.
❍
When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
❍
If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case, move the DVD
player away from the tuner and radio.
❍
The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
❍
Turn off the receiver before you connect or disconnect the DVD player’s power cord. If you leave the receiver power on, the
speakers may be damaged.
Warning
Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the coaxial digital audio jack of
this DVD player to an AV decoder that has the Dolby Digital (AC-3) decoding function. High volume sound may damage your hearing as well as the speakers. (Refer to “Selecting Digital Audio Output” on page 39.)
Notes
CONNECTIONS PAGE 15
Connecting to Optional Equipment
You can enjoy the high quality dynamic sound of Dolby Digital (AC-3), Dolby Pro Logic, and 2 Channel Digital Stereo.
Enjoying Dolby Digital (AC-3) Sound
COAXIAL
OPTICAL
DIGITAL OUT
AUDIO OUT
COMPONENT
VIDEO OUT
Y
Pr
Pb
S-VIDEO
OUT
L
1 2
R
VIDEO
OUT
To DIGITAL OUT
(COAXIAL or OPTICAL)
75 ohm coaxial cable
To S-VIDEO OUT
or VIDEO OUT
Connection
example
Front speaker
(left)
Rear speaker
(left surround)
Rear speaker
(right surround)
Front speaker
(right)
Sub woofer
To S-video Input
or Video Input
Center
speaker
To digital
audio input
Amplifier equipped
with a Dolby Digital
(AC-3) decoder
or Video cable
S-Video cable
Dolby Digital (AC-3)
Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to
reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs with this
dynamic realistic sound by connecting the DVD player to a 6 channel amplifier equipped with a Dolby Digital (AC-3)
decoder or Dolby Digital (AC-3) processor.
❍
Refer to the owner’s manual of your audio equipment as well.
❍
When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
❍
The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
❍
Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
Notes
To enjoy Dolby Digital (AC-3)
sound from this DVD player
you need the following:
● DVD video discs recorded in
Dolby Digital (AC-3)
● 6 channel amplifier equipped
with a Dolby Digital (AC-3)
decoder, of Dolby Digital
(AC-3) processor and power
amplifier
● 5 speakers and 1 sub woofer
To enjoy Dolby Digital (AC-3)
sound
You need to select the recording
system. And select “AC-3”.
* Manufactured under license from Dolby Laboratories Licensing
Corporation. “Dolby”, “AC-3” and the double-D symbol are trademarks of
Dolby Laboratories Licensing Corporation.
Confidential Unpublished Works. 1992-1997 Dolby Laboratories, Inc. All
rights reserved.
C
Loading...