machine number | DVC2515
enjoy the view
operating guide / warranty
®
PAGE 2 INTRODUCTION
Safety Precautions
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated ‘dangerous voltage’ within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION:
POUR EVITER LES CHOCS ELECTRIQUE, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOUD.
CAUTION: This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference, should the unit require maintenance, contact an authorized service location-see
service procedure.
Use of controls, adjustments or the performance of procedures other than those specified may
result herein hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation
when open the enclosure. DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connect
ed.
- Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
INDUSTRY CANADA REQUIREMENT :
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numéruque de la classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Zenith is a trademark of ZEC © Copyright Zenith Electronics Corporation 2000
RECORD YOUR MODEL NUMBER (Now, while you can see it)
The model and serial number of your new DVD
player are located on the back of the DVD player cabinet. For your future convenience, we suggest that you record these numbers here:
MODEL NO.____________________________________
SERIAL NO.____________________________________
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVERTISSEMENT
WARNING : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISQUE DE CHOC ELECTRIQUE NE
PAS OUVRIR
INTRODUCTION PAGE 3
Table of Contents
Introduction
❏ Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . 2
❏ Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . 3
❏ IMPORTANT SAFETY INSTRUCTIONS . . . . . . 4-5
❏ Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
❏ Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 7
❏ Identification of Controls . . . . . . . . . . . . . . . . . 8-12
Front Panel/Display window. . . . . . . . . . . . . . . . . . . . . 8
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Preparing the Remote Control . . . . . . . . . . . . . . . . . . 11
Operating with the Remote Control . . . . . . . . . . . . . . 11
Connections
❏ Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . 12
❏ Connecting to an Audio System . . . . . . . . . . . . . 13
❏ Connecting to Optional Audio System . . . . . . 14-16
Enjoying Dolby Digital (AC-3) Sound . . . . . . . . . . . . . 14
Enjoying Dolby Pro Logic Surround Sound . . . . . . . . 15
Enjoying 2 Channel Digital Stereo Sound. . . . . . . . . . 16
Enjoying DTS Sound. . . . . . . . . . . . . . . . . . . . . . . . . 16
Basic Operations
❏ Basic Playback . . . . . . . . . . . . . . . . . . . . . . . 17-21
Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Frame Advance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Skipping chapters and tracks forward or back . . . . . . 20
Scanning at High Speed . . . . . . . . . . . . . . . . . . . . . . . 21
Playing in Slow-Motion . . . . . . . . . . . . . . . . . . . . . . . 21
Operation Using GUI Menu Icons
❏ General Information about GUI menu icons . . . . 22
❏ Detailed description of each GUI menu icon. . . . 23
Advanced Operation
❏ Using a title menu . . . . . . . . . . . . . . . . . . . . . . . 24
❏ Using a DVD menu . . . . . . . . . . . . . . . . . . . . . . 24
❏ Changing subtitle language . . . . . . . . . . . . . . . . 25
❏ Changing audio soundtrack language . . . . . . . . . 25
❏ Viewing from another angle . . . . . . . . . . . . . . . . 26
❏ Producing a 3D Surround effect . . . . . . . . . . . . . 26
❏ Repeat Play. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
❏ Storing markers in memory to be
viewed (listened to) again. . . . . . . . . . . . . . . . . . 28
❏ Zoom Feature . . . . . . . . . . . . . . . . . . . . . . . . . . 29
❏ Random Play. . . . . . . . . . . . . . . . . . . . . . . . . . . 29
❏ Program Play. . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Initial Settings
❏ Common procedures of initial settings . . . . . . . . 31
❏ Selecting disc Languages . . . . . . . . . . . . . . . . . 32
❏ Selecting rating level and password . . . . . . . 33-34
❏ Selecting TV Aspect . . . . . . . . . . . . . . . . . . . . . . 35
❏ Selecting Menu Language . . . . . . . . . . . . . . . . . 36
❏ Selecting Digital Audio Output . . . . . . . . . . . . . . 37
❏ Table of Languages and Their Abbreviations . . . 38
Reference
❏ Disc Requirements/Copyright Information. . . . . . 39
❏ Before Calling Service Personnel . . . . . . . . . . . . 40
❏ Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 41
PAGE 4 INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL
AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire
hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation,
use and servicing.
This unit is fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read owner’s manual
After unpacking this product, read the owner’s
manual carefully, and follow all the operating and
other instructions.
2. Power Sources
This product should be operated only from the type
of power source indicated on the marking label. If
you are not sure of the type of power supply in your
home, consult your product dealer or local power
company. For products intended to operate from
battery power, or other sources, refer to the
operating instructions.
3. Grounding or Polarization
This product is equipped with a polarized alternating
current line plug (a plug having one blade wider than
the other). This plug will fit into the power outlet only
one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
4. Ventilation
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from overheating. These
openings must not be blocked or covered. The
openings should never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in
installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s
instructions have been adhered to.
5. Heat
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
6. Water and Moisture
Do not use this product near water-for example,
near a bath tub, wash bowl, kitchen sink. or laundry
tub; in a wet basement; or near a swimming pool
and the like.
7. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
8. Power-Cord Protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, playing particular
attention to cords at plugs, convenience receptacles,
and the point where they exit from the product.
9. Overloading
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result
in a risk of fire or electric shock.
10.Lightning
For added protection of this product during storms, or
when it is left unattended and unused for long
periods of time, unplug it from the wall outlet.
This will prevent damage to the product due to
lightning and power-line surges.
11.Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result in
a fire or electric shock. Never spill liquid of any kind
on the product.
12.Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
INTRODUCTION PAGE 5
IMPORTANT SAFETY INSTRUCTIONS
13.Accessories
Do not place this product on
an unstable cart, stand, tripod,
bracket, or table. The product
may fall, causing serious
injury to a child or adult, and
serious damage to the
product. Use only with a cart,
stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the
product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer. A product and cart combination should
be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product and
cart combination to overturn.
14.Disc Tray
Keep your fingers well clear of the disc tray as it is
closing. It may cause serious personal injury.
15.Burden
Do not place a heavy object on or step on the
product. The object may fall, causing serious
personal injury and serious damage to the product.
16.Connecting
When you connect the product to other equipment,
turn off the power and unplug all of the equipment
from the wall outlet. Failure to do so may cause an
electric shock and serious personal injury. Read the
owner’s manual of the other equipment carefully and
follow the instructions when making any
connections.
17.Sound Volume
Reduce the volume to the minimum level before you
turn on the product. Otherwise, sudden high volume
sound may cause hearing or speaker damage.
18.Sound Distortion
Do not allow the product to output distorted sound
for a longtime. It may cause speaker overheating
and fire.
19.Headphones
When you use the headphones, keep the volume at
a moderate level. If you use the headphones
continuously with high volume sound, it may cause
hearing damage.
20.Laser Beam
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of
the laser beam. It may cause sight damage.
21.Disc
Do not use a cracked, deformed, or repaired disc.
These discs are easily broken and may cause serious personal injury and product malfunction.
22.Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is
damaged.
b) If liquid has been spilled, or objects have fallen
into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e) If the product has been dropped or damaged in
any way.
f) When the product exhibits a distinct change in
performance-this indicates a need for service.
23.Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
24.Replacement parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.
25.Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in proper
operating condition.
PAGE 6 INTRODUCTION
Precautions
❏
When shipping the DVD player, always use the
original shipping carton and packing materials.
For maximum protection, repack the unit as it was
originally packed at the factory.
❏
Do not use volatile liquids, such as insect spray, near
the DVD player. Do not leave rubber or plastic
products in contact with the DVD player for a long
time. They will leave marks on the finish.
❏
The top and rear panels of the DVD player may
become warm after a long period of use. This is
normal and not a malfunction.
❏
When the DVD player is not in use, be sure to
remove the disc and turn off the power.
❏
If you do not use the DVD player for a long period, the
unit may not function properly in the future. Turn on
and use the DVD player occasionally.
❏
When you place this DVD player near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, move the DVD
player away from the TV, radio, or VCR.
Use a soft, dry cloth for cleaning.
❏
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry. Do not use any type of solvent, such as thinner
and benzine, as they may damage the surface of the
DVD player.
❏
If you use a chemical saturated cloth to clean the
unit, follow that product’s instructions.
Warning: Cleaning and adjustment of lenses
and/or other components of playback mechanism
should be performed by a qualified service
technician.
The DVD player is a high technology, precision device. If
the optical pick-up lens and disc drive parts are dirty or
worn down, the picture quality becomes poor. To obtain
a clear picture, we recommend regular inspection and
maintenance (cleaning or parts replacement) every
1,000 hours of use depending on the operating
environment. For details, contact your nearest dealer.
Moisture condensation damages the DVD player.
Please read the following carefully.
Moisture condensation occurs, for example, when
you pour a cold drink into a glass on a warm day.
Drops of water form on the outside of the glass. In
the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the DVD player.
Moisture condensation occurs during the following
cases.
❏
When you bring the DVD player directly from a cold
place to a warm place.
❏
When you use the DVD player in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
❏
In summer, when you use the DVD player in a hot
and humid place just after you move the unit from
an air conditioned room.
❏
When you use the DVD player in a humid place.
❏
Do not use the DVD player when moisture condensation may occur.
If you use the DVD player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the DVD player to the wall
outlet, turn on the DVD player and leave it “ON” for
two or three hours. After two or three hours, the
DVD player will have warmed up and evaporated
any moisture. Keep the DVD player connected to
the wall outlet and moisture condensation will seldom occur.
Notes on handling
Notes on Locating
Notes on Cleaning
To Obtain a Clear Picture
Notes on Moisture Condensation
E
x
a
m
p
l
e
s
o
f
m
o
i
s
t
u
r
e
c
o
n
d
e
n
s
a
t
i
o
n
Optical
pick-up lens
It’s too
warm!
Wait!
INTRODUCTION PAGE 7
Notes on Discs
This section shows you how to handle, clean, and store discs.
On Handling Discs
❍
Do not touch the playback side of the disc.
❍
Do not attach paper or tape to discs.
On Storing Discs
❍
Do not store discs in a place subject to
direct sunlight or near heat sources.
❍
Do not store discs in places subject to
moisture and dust such as a bathroom or
near a humidifier.
❍
Store discs vertically in a case. Stacking or
placing objects on discs outside of their
case may cause warping.
On Cleaning Discs
❍
Fingerprints and dust on the disc cause
picture and sound deterioration. Wipe the
disc from the center outward with a soft
cloth. Always keep the disc clean.
❍
If you cannot wipe off the dust with a soft
cloth, wipe the disc lightly with a slightly
moistened soft cloth and finish with a dry
cloth.
❍
Do not use any type of solvents such as
thinner, benzine, commercially available
cleaners or anti-static spray for vinyl LPs.
They may damage the disc.
About This Owner’s Manual
❍
This owner’s manual explains the basic
instructions of this DVD player.
❍
Some DVD video discs have functions that
may not be explained in this owner’s manual.
Therefore, some instructions may differ from
this owner’s manual, and there may be extra
instructions. In this case, follow the instructions
displayed on the TV screen or package.
❍
“ ” may appear on the TV screen
during operation. This icon means the
function explained in this owner’s manual is
not available on that specific DVD video
disc.
PAGE 8 INTRODUCTION
Identification of Controls
Front Panel
Display Window
open close
/
menu
select/enter
skip/scan
menu search
play
stop
pause step
/
power
12345
random repeat
disc select
clear
disc skip
disc exchange
/ /
TITLECD
PROG.
RANDOM ALL
AB
CHP/TRK
1
2
34
5
DVD
DVD indicator
CD indicator
RANDOM indicator
PROGRAM indicator
Repeat playback
mode indicators
Operating status indicator
Chapter/Track number indicator
Title number indicator
Angle icon indicator
Disc 1–5 indicators
Total playing time/elapsed time indicators
OPEN/CLOSE button
POWER indicator
PLAY button
SKIP/SCAN buttons
MENU button
STOP button
Disc tray
POWER button
PAUSE/STEP button
SELECT/ENTER
button
DISC SELECT (1 – 5)
buttons
Display window
DISC SKIP
button
DISC EXCHANGE
button
Remote sensor
RANDOM button
REPEAT button
CLEAR button
ARROW
buttons
INTRODUCTION PAGE 9
Identification of Controls
Rear Panel
S-VIDEO
OUT
DIGITAL
OUT
COAXIAL
AUDIO
OUT
VIDEO OUT
L
R
S-VIDEO OUT jack
AUDIO OUT (L/R) jacks
VIDEO OUT jack
POWER CORD
Connect to an AC 120V, 60Hz
outlet only.
COAXIAL DIGITAL
AUDIO OUT jack
PAGE 10 INTRODUCTION
Identification of Controls (con’d)
REMOTE CONTROL
You will find instructions for each of the remote control functions in the appropriate sections of this
instruction manual.
POWER button
***TITLE button
SETUP button
ZOOM button
DISPLAY button
**ARROW buttons
SELECT/ENTER button
PLAY button
STOP button
FWD/REV SLOW buttons
NUMBER buttons
CLEAR button
AUDIO button
SUBTITLE button
REPEAT button
DISC SKIP button
PROGRAM button
RANDOM button
OPEN/CLOSE button
*MENU button
MARKER-SEARCH buttons
RETURN button
PAUSE/STEP button
FWD/REV SCAN button
FWD/REV SKIP button
SOUND button
ANGLE button
A-B button
*MENU button
Use the MENU button to display the
menu screen included on DVD video
discs. To operate a menu screen,
follow the instructions in “Using a
DVD Menu” (page 22).
** Directional arrow buttons
(up, down, left, right) for use in highlighting a selection on a GUI menu
screen, TITLE and MENU screen.
***TITLE button
Use the TITLE button to display the
title screen included on DVD video
discs. To operate a menu screen,
follow the instructions in “Using a Title
Menu” (page 22).
power
setup title
zoom marker search
y
a
l
p
s
i
d
stop play pause/step
slow
select/
enter
scan
open/close
menu
r
e
t
u
skip
r
n
clear
audio
disc skip
sound
subtitle angle
repeat a-b
program random
PAGE 11 INTRODUCTION
Identification of Controls (con’d)
Insert the batteries into the remote control so you can
use it to operate the DVD player.
Open the battery cover.
Insert batteries (AAA size).
● Make sure to match the + and - on the batteries to
the marks inside the battery compartment.
Close the cover.
❍
Improper use of batteries may cause battery leakage and
corrosion.
❍
To operate the remote control correctly, follow the
instructions.
❍
Do not insert the batteries into the remote control in the
wrong direction.
❍
Do not charge, heat, open, or short-circuit the batteries.
Do not throw the batteries into fire.
❍
Do not leave dead or exhausted batteries in the remote
control.
❍
Do not use different types of batteries together, or mix
old and new batteries.
❍
If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage
from battery corrosion.
❍
If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.
❍
If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.
❍
The batteries should last about one year with normal
use.
This section shows you how to use the remote control.
Point the remote control at the
remote sensor and press the
buttons.
Distance: About 23 ft (7 m) from the front of the remote
sensor
Angle: About 30° in each direction of the front of the
remote sensor
* Do not expose the remote sensor of the DVD
player to a strong light source such as direct
sunlight or illumination. If you do so, you may not
be able to operate the DVD player with the remote
control.
❍
Direct the remote control at the remote sensor of the
DVD player.
❍
Do not drop or give the remote control a shock.
❍
Do not leave the remote control near extremely hot or
humid place.
❍
Do not spill water or put anything wet on the remote control.
❍
Do not open the remote control.
Preparing the Remote Control
Operating with the Remote Control
open close
/
menu
select/enter
skip/scan
menu search
play
stop
pause step
/
power
12345
random repeat
disc select
clear
disc skip
disc exchange
/ /
30° 30°
Within about 23 ft (about 7 m)
Notes on batteries
Notes on the remote control
1
2
3
power
open/close
setup title menu
zoom marker search
r
e
t
u
r
n
d
i
s
p
l
a
y
AAA
AAA
OPEN
CONNECTIONS PAGE 12
Connecting to a TV
Connect the DVD player to your TV
S-VIDEO
OUT
DIGITAL
OUT
COAXIAL
AUDIO
OUT
VIDEO OUT
L
R
S-video cable
(supplied)
To S-VIDEO OUT
To AUDIO OUT (L/R)/
VIDEO OUT
Audio/Video cable
(supplied)
To video input
To audio inputs
To S-video input
TV or monitor with
audio/video inputs
❍
Refer to the owner’s manual of your TV as well.
❍
When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
❍
Connect the DVD player to your TV directly. If you connect the DVD player to a VCR, the playback picture will be distorted
because DVD video discs are copy protected.
Warning
Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the DIGITAL AUDIO jack of this
DVD player to an AV decoder that has the Dolby Digital (AC-3) decoding function. High volume sound may damage your hearing
as well as the speakers. (Refer to “Selecting Digital Audio Output” on page 37.)
Notes
If the TV has an S-video input, connect the
DVD player with the supplied S-video cable.
PAGE 13 CONNECTIONS
Connecting to an Audio System
You can listen to the sound of audio CDs and DVD video discs in stereo.
S-VIDEO
OUT
DIGITAL
OUT
COAXIAL
AUDIO
OUT
VIDEO OUT
L
R
To audio inputs
Audio system
To VIDEO OUT To AUDIO OUT (L/R)
S-video cable (supplied)
To S-VIDEO OUT
To video input
To S-video input
TV or monitor with
audio/video inputs
Audio cable
(supplied)
Video cable
(supplied)
If the TV has an S-video input, connect the DVD
player with the supplied S-video cable.
❍
Refer to the owner’s manual of your audio system as well.
❍
When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
❍
If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case, move the DVD
player away from the tuner and radio.
❍
The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
❍
Turn off the receiver before you connect or disconnect the DVD player’s power cord. If you leave the receiver power on, the
speakers may be damaged.
Warning
Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the DIGITAL AUDIO jack of this
DVD player to an AV decoder that has the Dolby Digital (AC-3) decoding function. High volume sound may damage your hearing as
well as the speakers. (Refer to “Selecting Digital Audio Output” on page 37.)
Notes
Loading...