Zenith DVB611 Installation Manual

DV172NZ_HA1ULZ_ENG

Installation and Operating Guide | Warranty

Model Number | DVB611 | DVD Player

© Copyright 2006, LG Electronics U.S.A., Inc.

For service/

support Call:

Toll Free Number

1-800-243-0000

2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

This lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the user
to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the product.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.

CAUTION: Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.

Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect
it from over heating.
The openings should be never be blocked by placing the
product on a bed, sofa, rug or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or
the manufacturer's instruction have been adhered to.

PERSONNEL.

CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.

FCC WARNING: This equipment may generate or use
radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is
made.

REGULATORY INFORMATION: FCC Part 15

This epuipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
product is operated in a residential installation. This product
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
product does cause harmful interference to radio or
television reception, which can be determined by turning the
product off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the product and
receiver.

• Connect the product into an outlet on a circuit
different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV
technician for help.

FCC COMPLIANCE: The responsible party for this
product’s compliance is:

Marketed and Distributed by LG Electronics U.S.A., Inc.,
1000 Sylvan Avenue, Englewood Cliffs, NJ.
Phone: [phone].

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS DEFEATED.

CAUTION:

This product employs a Laser System.
To ensure proper use of this product, please read this
owner’s manual carefully and retain it for future reference.
Should the unit require maintenance, contact an authorized
service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.

CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a
dedicated circuit;

That is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch circuits.
Check the specification page of this owner's manual to be
certain.

Do not overload wall outlets. Overloaded wall outlets, loose
or damaged wall outlets, extension cords, frayed power
cords, or damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets,
and the point where the cord

exits the appliance.

To disconnect power from the mains, pull out the mains cord
plug. When installing the product, ensure that the plug is
easily accessible.

3

1. Read these instructions. - All these safety and operating

instructions should be read before the product is operated.

2. Keep these instructions. - The safety, operating and use
instructions should be retained for future reference.

3. Heed all warnings. - All warnings on the product and in
the operating instructions should be adhered to.

4. Follow all instructions. - All operating and use
instructions should be followed.

5. Do not use this product near water. – For example: near
a bath tub, wash bowl, kitchen sink, laundry tub, in a wet
basement; or near a swimming pool; and other areas
located near water.

6. Clean only with dry cloth. – Unplug this product from the
wall outlet before cleaning. Do not use liquid cleaners.

7.

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. -

Slots
and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to
protect it from over- heating. The openings should never
be blocked by placing the product on a bed, sofa, rug or
other similar surface. This product should not be placed in
a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instructions have been adhered to.

8.

Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.

9. D

o not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades

with one wider than the other. A grounding

type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
product.

11. Only use attachments/accessories specified by the
manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with
apparatus. When a cart is used, use caution when
moving the cart/product combination to avoid injury
from tip-over.

13. Unplug this product during lightning storms or when
unused for long periods of time.

14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the product, the product has been
exposed to rain or moisture, does not operate
normally, or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:

PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND
THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or
fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for
installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

Contents

Introduction . . . . . . . . . . . . . . . . . .5-8

About the Symbol Display . . . . . . . . . . . . .5

Symbol used in this Manual . . . . . . . . . . . . . .5

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . .5

Handling Discs . . . . . . . . . . . . . . . . . . . . . . .5

Storing Discs . . . . . . . . . . . . . . . . . . . . . . . .5

Cleaning Discs . . . . . . . . . . . . . . . . . . . . . . .5

Types of Playable Discs . . . . . . . . . . . . . . . . .6

Regional Code . . . . . . . . . . . . . . . . . . . . . . . . .6

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Remote Control . . . . . . . . . . . . . . . . . . . . . . . .8

Remote Control Operation . . . . . . . . . . . . . .8

Remote Control Battery Installation . . . . . . .8

Installation and Setup . . . . . . . . .9-14

Setting up the Player . . . . . . . . . . . . . . . . . . . .9

DVD Player Connections . . . . . . . . . . . . . . . . .9

Video and Audio Connections to Your TV . . .9

Audio Connection to Optional Equipment . .10

Displaying Disc Information on-screen . . . . .11

Initial Settings . . . . . . . . . . . . . . . . . . . . . . . .11

General Operation . . . . . . . . . . . . . . . . . . .11

LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . .12

• Menu Language . . . . . . . . . . . . . . . . . . .12

• Disc Audio / Subtitle / Menu . . . . . . . . . .12

DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . .12

• TV Aspect . . . . . . . . . . . . . . . . . . . . . . . .12

• Display Mode . . . . . . . . . . . . . . . . . . . . .12

• Progressive Scan . . . . . . . . . . . . . . . . . .12

AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

• Dolby Digital / DTS / MPEG . . . . . . . . . .13

• Sample Freq. (Frequency) . . . . . . . . . . . .13

• Dynamic Range Control (DRC) . . . . . . . .13

• Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . .13

LOCK (Parental Control) . . . . . . . . . . . . . .13

• Rating . . . . . . . . . . . . . . . . . . . . . . . . . . .13

• Password . . . . . . . . . . . . . . . . . . . . . . . .13

• Area Code . . . . . . . . . . . . . . . . . . . . . . .14

OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . .14

• PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

• Auto Play . . . . . . . . . . . . . . . . . . . . . . . .14

• B.L.E. (Black Level Expansion) . . . . . . . .14

• DivX(R) VOD . . . . . . . . . . . . . . . . . . . . .14

Operation . . . . . . . . . . . . . . . . . .15-20

General Features . . . . . . . . . . . . . . . . . . . . . .15

Additional Features . . . . . . . . . . . . . . . . . . . .16

Playing an Audio CD or MP3/WMA file . . . . .17

Programmed Playback . . . . . . . . . . . . . . . . .17

Repeat Programmed Tracks . . . . . . . . . . . .17

Erasing a Track from Program List . . . . . . .17

Erasing the Complete Program List . . . . . .17

Viewing a JPEG file . . . . . . . . . . . . . . . . . . . .18

Slide Show . . . . . . . . . . . . . . . . . . . . . . . . .18

Still Picture . . . . . . . . . . . . . . . . . . . . . . . . .18

Moving to another File . . . . . . . . . . . . . . . .18

Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

To rotate picture . . . . . . . . . . . . . . . . . . . . .18

Playing a DivX Movie file . . . . . . . . . . . . . . . .19

Controlling other TVs with the Remote Control

Maintenance and Service . . . . . . . . . . . . . . .20

.

Reference . . . . . . . . . . . . . . . . . .21-22

Language Codes . . . . . . . . . . . . . . . . . . . . . . .21

Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .22

Specifications . . . . . . . . . . . . . . . . . . . . . . . . .22

20

4

Operation

Reference

Installation and Setup

5

To ensure proper use of this product, please read this
owner’s manual carefully and retain for future
reference.

This manual provides information on the operation
and maintenance of your DVD player. Should the unit
require service, contact an authorized service location.

About the Symbol Display

“ ” may appear on your TV display during
operation and indicates that the function explained in
this owner’s manual is not available on that specific
DVD video disc.

Symbol Used in this Manual

Note:

Indicates special notes and operating features.

Tip:

Indicates tips and hints for making the task easier.

A section whose title has one of the following symbols
is applicable only to the disc represented by the
symbol.

All discs listed below

DVD and finalized DVD±R/RW

Video CDs

Audio CDs

MP3 files

WMA files

DivX files

Notes on Discs

Handling Discs

Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.

Storing Discs

After playing, store the disc in its case. Do not expose
the disc to direct sunlight or sources of heat and never
leave it in a parked car exposed to direct sunlight.

Cleaning Discs

Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center out.

Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.

DivX

WMA

MP3

ACD

VCD

DVD

ALL

Introduction

Introduction

6

Types of Playable Discs

DVD
(8 cm / 12 cm disc)

Video CD (VCD/SVCD)
(8 cm / 12 cm disc)

Audio CD
(8 cm / 12 cm disc)

In addition, this unit plays DVD±R/RW and CD-R/RW
that contains audio titles, DivX, MP3, WMA, and/or
JPEG files.

Notes:

• Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD±R/RW) disc
itself, some CD-R/RW (or DVD±R/RW) discs
cannot be played on the unit.

• Do not use irregularly shaped CDs (e.g., heart­shaped or octagonal) since they may result in
malfunctions.

• This DVD player requires discs and recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are
many different types of recordable disc formats
(including CD-R containing MP3 or WMA files) and
these require certain pre-existing conditions (see
above) to ensure compatible playback.

Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has
no right to grant such permission. Permission
should always be sought from the copyright
owner.

Regional Code

This unit has a regional code printed on the rear of the
unit. This unit can play only DVD discs labelled same
as the rear of the unit or “ALL”.

Notes on Regional Codes

• Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or the
disc cannot play.

• If you try to play a DVD with a different regional
code from your player, the message “Check
Regional Code” appears on the TV screen.

Notes on Copyrights:

It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyrighted
material without permission. This product features the
copy protection function developed by Macrovision.
Copy protection signals are recorded on some discs.
When recording and playing the pictures of these
discs picture noise will appear. This product
incorporates copyright protection technology that is
protected by method claims of certain U.S. patents
and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use
of this copyright protection technology must be
authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.

CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE. IN CASE OF 525 PROGRESSIVE
SCAN PICTURE PROBLEMS, IT IS
RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL
525p DVD PLAYER, PLEASE CONTACT OUR
CUSTOMER SERVICE CENTER.

Operation

Reference

Installation and Setup

7

Introduction

Front Panel

a bcde

fghi

a POWER

Switches the unit ON and OFF.

b N (PLAY)

Starts playback.

c x (STOP)

Stops playback.

d SKIP (.)

Go to next chapter or track.

e SKIP (>)

Returns to beginning of current chapter or track or
go to previous chapter or track.

f Disc Tray

Insert a disc here.

g Z (OPEN / CLOSE)

Opens or closes the disc tray.

h Display window

Shows the current status of the unit.

i Remote Sensor

Point the Remote Control

here.

8

Remote Control

POWER

Switches DVD Player ON and OFF.

OPEN/CLOSE (Z)

Opens and closes the disc tray.

0-9 numerical buttons

Selects numbered items in a menu.

CLEAR

Removes a track number on the

Program List or a mark on the

Marker Search menu.

TV Control Buttons

POWER: Turns the TV on or off.

AV: Selects the TV’s source.

PR/CH +/–: Selects TV’s channel.

VOL +/–: Adjusts TV’s volume.

DVD MENU

Accesses menu on a DVD disc.

TITLE

Displays title menu, if available.

b / B / v / V (left/right/up/down)

Selects an item in the menu.

DISPLAY

Accesses On-Screen Display.

RETURN (O)

Displays the video CD with PBC.

SCAN (m / M)

Search backward or forward.

SKIP (. / >)

Go to next chapter or track. Returns
to beginning of current chapter or
track or go to previous chapter or
track.

PAUSE / STEP ( X )

Pauses playback temporarily/ press
repeatedly for frame-by-frame
playback.

N (PLAY)

Starts playback.

STOP (x)

Stops playback.

AUDIO

Selects an audio language or an
audio channel.

SUBTITLE

Selects a subtitle language.

ANGLE

Selects a DVD camera angle, if
available.

SETUP

Accesses or removes the Setup
menu.

MARKER

Marks any point during playback.

SEARCH

Displays MARKER SEARCH menu.

PROGRAM

Enter to program edit mode.

ZOOM

Enlarges video image.

REPEAT

Repeat chapter, track, title, all.

A-B

Repeat sequence from point A to
point B.

RANDOM

Plays tracks in random order.

Remote Control Operation

Point the Remote Control

at the remote sensor and

press the buttons.

Caution:

Do not mix old and new batteries and never mix
different types of batteries such as standard, alkaline,
etc.

Remote Control Battery installation

Detach the battery cover on the rear of the

Remote Control

AAA

AAA

(size AAA) with 3 and # aligned correctly.

, and insert two batteries

Operation

Reference

Introduction

9

Installation and Setup

Installation and Setup

Setting up the Player

The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. If this occurs,
position the player away from the TV, VCR, or radio,
or turn off the unit after removing the disc.

DVD Player Connections

Depending on your TV and other equipment there are
various ways you can connect the player. Please refer
to the manuals of your TV, stereo system or other
devices as necessary for additional connection
information.

Video and Audio Connections
to Your TV

Make sure the DVD player is connected directly to the
TV and not to a VCR, otherwise the DVD image could
be distorted by the copy protection system.

Video – Connect the VIDEO OUT jack on the
DVD player to the video in jack on the TV using
the video cable (V)

S-Video – Connect the S-VIDEO OUT jack on the
DVD Player to the S-Video in jack on the TV using
the S-Video cable (S).

Component Video – Connect the COMPONENT
VIDEO OUT/PROGRESSIVE SCAN jacks on the
DVD Player to the corresponding in jacks on the
TV using an Y Pb Pr cable (C).

Progressive Scan

• If your television is a high-definition or “digital
ready” television, you may take advantage of
the unit’s progressive scan output for

higher video resolution.

• Set the Progressive to “On” on the setup
menu for progressive signal, see page 12.

• Progressive scan does not work with the
analog video connections (yellow VIDEO OUT
jack).

Audio – Connect the left and right AUDIO OUT
jacks of the DVD Player to the audio left and right
IN jacks on the TV (A) using the audio cables.
Do not connect the DVD Player’s AUDIO OUT jack
to the phone in jack (record deck) of your audio
system.

10

Audio Connection to Optional

DTS and DTS Digital Out are trademarks
of Digital Theater Systems, Inc.

Equipment

Connect the DVD player to your optional equipment
for audio output.

Rear of DVD player

AX

L

COAXIAL

Amplifier (Receiver)

Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic”, and
the double-D symbol are trademarks of
Dolby Laboratories.

R

AUDIO INPUTDIGITAL INPUT

Amplifier equipped with 2-channel analog stereo
or Dolby Pro Logic ll / Pro Logic: Connect the left

and right AUDIO OUT jacks on the DVD player to the
audio left and right IN jacks on your amplifier,
receiver, or stereo system, using the audio cables (A).

Amplifier equipped with 2-channel digital stereo
(PCM) or audio / video receiver equipped with a
multi-channel decoder (Dolby Digital™, MPEG 2,
or DTS): Connect the DVD Player’s DIGITAL

AUDIO OUT jack

(COAXIAL X) to the corresponding
in jack on your amplifier. Use an optional digital
(COAXIAL X) audio cable.

Digital Multi-channel sound

A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel audio
/ video receiver that supports one or more of the
audio formats supported by your DVD player such as
MPEG 2, Dolby Digital and DTS. Check the receiver
manual and the logos on the front of the receiver.

Notes:

If the audio format of the digital output does not match

•

the capabilities of your receiver, the receiver produces
a strong, distorted sound or no sound at all.

• Six Channel Digital Surround Sound via a digital

connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.

•

Operation

Reference

Introduction

11

Installation and Setup

Displaying Disc Information
on-screen

You can display various information about the disc
loaded on-screen.

1. Press DISPLAY to show various playback
information.
The items displayed differ depending on the disc
type or playing status.

1 / 3

1 / 12

0:20:09

ABC

2. You can select an item by pressing v / V and
change or select the setting by pressing b / B.



Title (Track) – Current title (or track).
number/total number of titles (or tracks).



Chapter – Current chapter number/total number
of chapters.



Time – Elapsed playing time.



Audio – Selected audio language or channel.



Subtitle – Selected subtitle.



Angle – Selected angle/total number of angles.



Sound – Selected sound mode.

Note:

If no button is pressed for a few seconds, the on­screen display disappears.

1 ENG

1 / 1

3D SUR.

Initial Settings

By using the Setup menu, you can make various
adjustments to items such as picture and sound. You
can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 12 to 14.

To display and exit the Menu:

Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.

To go to the next level:

Press B on the Remote Control.

To go back to the previous level:

Press b on the Remote Control.

General Operation

1. Press SETUP. The Setup menu appears.

2. Use v / V to select the desired option then press
B to move to the second level. The screen shows
the current setting for the selected item, as well as
alternate setting(s).

3. Use v / V to select the second desired option then
press B to move to the third level.

4. Use v / V to select the desired setting then press
ENTER to confirm your selection. Some items
require additional steps.

5. Press SETUP or PLAY to exit the Setup menu.

12

LANGUAGE

Menu Language

Select a language for the Setup menu and on-screen
display.

Disc Audio / Subtitle / Menu

Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.

Original – Refers to the original language in which
the disc was recorded.

Other – To select another language, press number
buttons then ENTER to enter the corresponding 4­digit number according to the language code list
on page 21. If you enter the wrong language code,
press CLEAR.

DISPLAY

Progressive Scan

Progressive Scan Video provides higher quality

pictures with less flickering.
If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with
a progressive scan signal, set Progressive Scan to
On.

To Turn ON progressive scan:

Connect component out of the DVD to the input of
your monitor/television, set your television or monitor
to Component Input.

1. Select “Progressive Scan” on the DISPLAY menu

then press B.

2. Select “On” using the v / V buttons.

3. Pressing ENTER will set the player to Progressive
scan mode.

Caution:

Once the setting for progressive scan output is
entered, an image will only be visible on a progressive
scan compatible TV or monitor. If you set Progressive
Scan to On in error, you must reset the unit. First,
remove the disc in the DVD Player. Next, press STOP

on the Remote Control ( x ) and hold it for five

seconds before releasing it. The video output will be
restored to the standard setting, and a picture will
once again be visible on a conventional analog TV or
monitor.

TV Aspect

4:3 – Select when a standard 4:3 TV is connected.

16:9 – Select when a 16:9 wide TV is connected.

Display Mode

Display Mode setting works only when the TV Aspect
mode is set to “4:3”.

Letterbox – Displays a wide picture with bands on
the upper and lower portions of the screen.

Panscan – Automatically displays the wide picture
on the entire screen and cuts off the portions that
do not fit.

Operation

Reference

Introduction

13

Installation and Setup

AUDIO

Each DVD disc has a variety of audio output options.
Set the player’s AUDIO options according to the type
of audio system you use.

Dolby Digital / DTS / MPEG

Bitstream – Select “Bitstream” if you connect this

unit’s DIGITAL OUT jack to an amplifier or other
equipment with a Dolby Digital, DTS or MPEG
decoder.

PCM (for Dolby Digital / MPEG) – Select when
connected to a two-channel digital stereo amplifier.
DVDs encoded in Dolby Digital or MPEG will be
automatically downmixed to two-channel PCM
audio.

Off (for DTS): If you select “Off”, the DTS signal is
not output through the DIGITAL OUT jack.

Sample Freq. (Frequency)

If your receiver or amplifier is NOT capable of
handling 96 kHz signals, select 48 kHz. When this
choice is made, this unit automatically converts any
96 kHz signals to 48 kHz so your system can decode
them.

If your receiver or amplifier is capable of handling 96
kHz signals, select 96 kHz.

Check the documentation for your amplifier to verify
its capabilities.

Dynamic Range Control (DRC)

With the DVD format, you can hear a program’s
soundtrack in the most accurate and realistic
presentation possible. However, you may wish to
compress the dynamic range of the audio output (the
difference between the loudest sounds and the
quietest ones). This allows you to listen to a movie at
a lower volume without losing clarity of sound. Set
DRC to On for this effect.

Vocal

Set to On only when a multi-channel karaoke DVD is
playing. The karaoke channels on the disc mix into
normal stereo sound.

LOCK (Parental Control)

Rating

Blocks playback of rated DVDs based on their
content. Not all discs are rated.

1. Select “Rating” on the LOCK menu then

press B.

2. To access the LOCK options, you must input the
password you have created. If you have not yet
entered password, you are prompted to do so.

Input a password and press ENTER. Enter it again
and press ENTER to verify. If you make a mistake
before pressing ENTER, press CLEAR.

3. Select a rating from 1 to 8 using the v / V buttons.

Rating 1-8: Rating one (1) has the most
restrictions and rating eight (8) is the least
restrictive.

Unlock: If you select unlock, parental control is
not active and the disc plays in full.

4. Press ENTER to confirm your rating selection, then
press SETUP to exit the menu.

Password

You can enter or change password.

1. Select Password on the LOCK menu then press B.

2. Follow step 2 as shown above (Rating).

To change the password, press ENTER when the
“Change” option is highlighted. Input a password
and press ENTER. Enter it again and press
ENTER to verify.

3. Press SETUP to exit the menu.

If you forget your password

If you forget your password, you can clear it using the
following steps:

1. Press SETUP to display the Setup menu.

2. Input the 6-digit number “210499” and press

ENTER. The password is cleared.

14

Area Code

Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list on
page 21.

1. Select “Area Code” on the LOCK menu then

press B.

2. Follow step 2 as shown previous page (Rating).

3. Select the first character using v / V buttons.

4. Press B and select the second character using
v / V buttons.

5. Press ENTER to confirm your Area code selection.

OTHERS

PBC

Set Playback Control (PBC) to On or Off.

On: Video CDs with PBC are played according to

the PBC.

Off: Video CDs with PBC are played the same

way as Audio CDs.

Auto Play

You can set up the unit so a DVD disc automatically
starts playing whenever the DVD is inserted.
If Auto Play mode is set to On, this unit will search for
title that has the longest playback time and then play
back the title automatically.

Note:

The Auto Play function may not work for some DVDs.

B.L.E. (Black Level Expansion)

To select the black level of playback pictures. Set your
preference and monitor’s ability.

On: Expanded grey scale. (0 IRE cut off)

Off: Standard grey scale. (7.5 IRE cut off)

DivX(R) VOD

We provide you the DivX

®

VOD (Video On Demand)
registration code that allows you to rent and purchase
videos using the DivX

®

VOD service. For more

information, visit www.divx.com/vod.

1. Select “DivX(R) VOD” option then press B.

2. Press ENTER while “Select” is selected and the

registration code will appear.
Use the registration code to purchase or rent the
videos from DivX

®

VOD service at
www.divx.com/vod. Follow the instructions and
download the video onto a disc for playback on
this unit.

3. Press ENTER to exit.

Note:

All the downloaded videos from DivX

®

VOD can only

be played back on this unit.

Operation

Reference

Introduction

15

Installation and Setup

Operations

General features

Buttons Operations

Z (OPEN / CLOSE) Opens or closes the disc tray.

X (PAUSE) During playback, press X to pause playback.

Press X repeatedly to play Frame-by-Frame.

SKIP (. / >) During playback, press SKIP (. or >) to go to the

next chapter/track or to return to the beginning of the
current chapter/track.

Press SKIP . twice briefly to step back to the previous
chapter/track.

SCAN (m / M) During playback, press SCAN (m or M) repeatedly to

select the required scan speed.
DVD, DivX disc; 4 steps
Video CD, MP3, Audio CD ; 3 steps

While the playback is paused, press SCAN M
repeatedly to play in slow motion (4 steps, forward only).

REPEAT During playback, press REPEAT repeatedly to select a

desired repeat mode.
DVD Video discs: Chapter/Title/Off
Video CD, Audio CD, DivX/MP3/WMA discs: Track/All/Off

A-B During playback, each press of A-B button to select point

A and point B and repeats a sequence from point A
(Starting point) to point B (End point).
Press CLEAR to exit.

ZOOM During playback or pause mode, press ZOOM to enlarge

the video image (4 steps).
You can move through the zoomed picture using bBvV

buttons. Press CLEAR to exit.

RANDOM During playback or in stop mode, press RANDOM for

random playback.

TITLE If the current DVD title has a menu, the title menu

appears on the screen. Otherwise, the disc menu may
appears.

DVD MENU The disc menu appears on the screen.

(ANGLE) During playback of DVD disc contains scenes recorded

different camera angles, press ANGLE repeatedly to
select a desired angle.

(SUBTITLE) During playback, press SUBTITLE repeatedly to select a

desired subtitle language.

(AUDIO) During playback, press AUDIO repeatedly to hear a

different audio language or audio track.

Discs

VCD

DivXDVD

DivXDVD

DVD

DVD

DVD

WMA

MP3ACD

DIVX

VCDDVD

ACDDivX

VCDDVD

ALL

DivXVCDDVD

MP3ACD

DivXVCDDVD

ALL

DivXVCDDVD

ALL

ALL

16

Notes on general features:

• On a Video CD with PBC, you must set PBC to Off
on the setup menu to use the repeat function (See
“PBC” on page 14).

• If you press SKIP (>) once during Repeat Chapter
(Track) playback, the repeat playback cancels.

• Zoom may not work on some DVDs.

• When you are playing a DVD disc contains scenes
recorded different camera angles, the angle indicator
will blink on the TV screen during scenes recorded
at different angles as an indication that angle
switching is possible

.

• The A-B repeat function is available only in the
current track.

Additional features

3D Surround

To produce a 3D surround effect that simulates multi­channel audio from two stereo speakers (instead of the
five+ speakers normally required for multi-channel
audio from a home theater system).

1. Press DISPLAY during playback.

2. Use 3 or 4 to select the sound option.

The sound option will be highlighted.

3. Use 1 or 2 to to select “3D SUR”.

To turn off the 3D Surround effect, select “Normal”.

1. Press AUDIO during playback.

“3D SUR.” appears on the menu screen.

2. To return to normal playback, press AUDIO

repeatedly until “3D SUR.” disappears from the
menu screen.

Time Search

To start playing at any chosen time on the disc:

1. Press DISPLAY during playback.

2. Press v / V to select the time clock icon and

“--:--:--” appears.

3. Input the required start time in hours, minutes, and

seconds from left to right. If you enter the wrong
numbers, press CLEAR to remove the numbers
you entered. Then input the correct numbers.

4. Press ENTER to confirm. Playback starts from the

selected time.

Marker Search

To enter a Marker

You can start playback from up to nine memorized
points. To enter a marker, press MARKER at the
desired point on the disc. The Marker icon appears on
the TV screen briefly. Repeat to enter up to nine
markers.

To Recall or Clear a Marked Scene

1. During disc playback, press SEARCH. The marker
search menu appears on the screen.

2. Within 10 seconds, press b / B to select a marker
number that you want to recall or clear.

3. Press ENTER and playback starts from the marked
scene. Or, Press CLEAR and the marker number is
erased from the list.

4. You can play any marker by inputting its number on
the marker search menu.

Last Scene Memory

This player memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the player or switch
off the player. If you load a disc that has the scene
memorized, the scene is automatically recalled.

Note:

This player does not memorize the scene of a disc if
you switch off the player before commencing to play
the disc.

Screen Saver

The screen saver appears when you leave the DVD
player in Stop mode for about five minutes. If the
Screen Saver is displayed for five minutes, the DVD
Player automatically turns itself off.

VCDACDDVD

DivXVCDDVD

DivXVCDDVD

ACD

DivXVCDDVD

Reference

Installation and

Setup

Introduction

17

Operation

Playing an Audio CD or
MP3/WMA file

This unit can play Audio CDs or MP3/WMA files
recorded media.

MP3/ WMA/ Audio CD

Once you insert an MP3/WMA files recorded media or
Audio CD, a menu appears on the TV screen.
Press v / V to select a track/file then press PLAY or
ENTER and playback starts. You can use variable
playback functions. Refer to page 15-16.

ID3 TAG

• When playing a file containing information such as
track titles, you can see the information by pressing
DISPLAY.
[ Song, Artist, Album, Comment, Genre ]

Tips:

• Press DVD MENU to move to the next page.

• On a CD with MP3/WMA and JPEG you can switch
MP3/WMA and JPEG. Press TITLE and MUSIC or

PHOTO word on top of the menu is highlighted.

Programmed Playback

The program function enables you to store your
favorite tracks from any disc in the player memory.
A program can contain 30 tracks.

1. Insert an Audio CD or MP3/WMA files recorded
media. AUDIO CD or MUSIC menu appears.

2. During STOP mode, press PROGRAM and
the mark will appear

Note:

Press PROGRAM again to exit the program edit
mode, then the mark will disappear.

3. Select a track on the “List”, then press ENTER to
place the selected track on the “Program” list.
Repeat to place additional tracks on the list.

4. Select the track you want to start playing on the
“Program” list.

5. Press PLAY or ENTER to start. Playback begins in
the order in which you programmed the tracks.
Playback stops after all of the tracks on the
“Program” list have played once.

6. To resume normal playback from programmed
playback, select a track on the list and then press
PLAY.

Repeat Programmed Tracks

Press REPEAT to select a desired repeat mode.

• Track: repeats the current track

• All: repeats all the tracks on programmed list.

• Off(No display): does not play repeatedly.

Note:

If you press > once during Repeat Track playback,
the repeat playback cancels.

Erasing a Track from “Program” List

1. During STOP mode, press PROGRAM and
the mark will appear

2. Use vVb Bto select the track that you wish to
erase from the Program list.

3. Press CLEAR. Repeat step 1~3 to erase additional
tracks on the list.

Erasing the Complete Program List

1. During STOP mode, press PROGRAM and
the mark will appear

2. Use vVb Bto select “Clear All”, then press
ENTER.

Note:

The programs are also cleared when the power is off
or the disc is removed.

MP3 / WMA disc compatibility with this player is
limited as follows:

• Sampling frequency: within 8 - 48 kHz (MP3),
within 32 - 48kHz (WMA)

• Bit rate: within 8 - 320kbps (MP3),
32 - 384 kbps (WMA)

• The player cannot read an MP3/WMA file that has
a file extension other than “.mp3” / “.wma”.

• CD-R physical format should be ISO 9660

• If you record MP3 / WMA files using software that
cannot create a file system (eg. Direct-CD) it is
impossible to playback MP3 / WMA files. We
recommend that you use Easy-CD Creator, which
creates an ISO 9660 file system.

• File names should have a maximum of 8 letters
and must incorporate an .mp3 or .wma extension.

• They should not contain special letters such as / ?
* : “ < > l etc.

• The total number of files in a folder should be less
than 1190 files.

E

E

E

E

18

Viewing a JPEG file

This unit can play JPEG files recorded media.

1. Insert a JPEG files recorded media. The PHOTO
menu appears on the TV screen.

2. Press v / V to select a folder, and press ENTER.
A list of files in the folder appears.

3. If you want to view a particular file, press
v / V to highlight a file and press ENTER or PLAY.

4. To return to the PHOTO menu while watching
pictures, press STOP.

Tips:

• If you are in a file list and want to return to the

previous Folder list, use v / V buttons to highlight

and press ENTER.

• Press DVD MENU to move to the next page.

• There are three Slide Speed options : >>>

(Fast), >> (Normal) and > (Slow).
Use vVbBto highlight . Then, use b / B to

select the option you want to use then press
ENTER.

• On a disc with MP3/WMA and JPEG you can switch

MP3/WMA and JPEG. Press TITLE and MUSIC or
PHOTO word on top of the menu is highlighted.

• While watching a picture, press RETURN to hide

the help menu.

Slide Show

Use vVbBto highlight the (Slide Show) then
press ENTER.

Still Picture

1. Press PAUSE/STEP during slide show.
The player will now go into PAUSE mode.

2. To return to the slide show, press PLAY or press
PAUSE/STEP again.

Moving to another File

Press SKIP (. or >) or cursor (b or B) once
while viewing a picture to advance to the next or
previous file.

Zoom

During watching pictures, press ZOOM to enlarge the
video image (4 steps).
You can move through the zoomed picture using bB
vVbuttons.

To rotate picture

Press v / V during showing a picture to rotate the
picture clockwise or counter clockwise.

JPEG disc compatibility with this player is
limited as follows:

• Depending upon the size and number of JPEG
files, it could take a long time for the DVD player
to read the disc’s contents. If you do not see an
on-screen display after several minutes, some of
the files may be too large — reduce the resolution
of the JPEG files to less than 5 million pixels and
burn another disc.

• The total number of files in a folder should be less
than 1190 files.

• Some discs may be incompatible due to a
different recording format or the condition of disc.

• Ensure that all the selected files have the “.jpg”
extensions when copying into the CD layout.

• If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” file.

• File names without “.jpg” extension will not be
able to be read by this unit. Even though the files
are shown as JPEG image files in Windows
Explorer.

Reference

Installation and

Setup

Introduction

19

Operation

Playing a DivX Movie file

Using this DVD Player you can play DivX file.

1. Insert a DivX file recorded media. The MOVIE
menu appears on the TV screen.

2. Press v / V to select a folder, and press ENTER.
A list of files in the folder appears.

3. If you want to view a particular file, press v / V to
highlight a file and press ENTER or PLAY.
You can use variable playback functions. Refer to
page 15-16.

4. Press STOP to stop the playback. The Movie
menu appears

Tips:

• If you are in a file list and want to return to the

previous Folder list, use the v / V buttons on the
remote to highlight and press ENTER.

• Press DVD MENU to move to the next page.

• On a CD with MP3/WMA, JPEG and MOVIE file,

you can switch MUSIC, PHOTO and MOVIE menu.
Press TITLE and MUSIC, PHOTO and MOVIE word
on top of the menu is highlighted.

• The disc subtitle may not be displayed properly, if a

DivX subtitle is downloaded through the internet.

• If the Disc Subtitle setup menu does not have the

DivX subtitile language you are going to play, the
subtitle may not be displayed properly.

Notice for displaying the DivX subtitle

If the subtitle does not display properly during
playback, press and hold SUBTITLE about 3 seconds
then press b / B to select another language code until
the subtitle is displayed properly.

DivX disc compatibility with this player is limited
as follows:

• Available resolution size of the DivX file is under

720x576 (W x H) pixel.

• The file name of the DivX subtitle is available by
56 characters.

• If there is impossible code to express in the DivX
file, it may be displayed as “ _ ” mark on the
display.

• If the number of the screen frame is over 30
per 1 second, this unit may not operate
normally.

• If the video and audio structure of recorded
file is not interleaved, either video or audio is
outputted.

• If the file is recorded with GMC, the unit
supports only 1-point of the record level.

*

GMC?
GMC is the acronym for Global Motion
Compensation. It is an encoding tool specified in
MPEG4 standard. Some MPEG4 encoders, like
DivX or Xvid, have this option.
There are different levels of GMC encoding,
usually called 1-point, 2-point, or 3-point GMC.

Playable DivX file

.avi, .mpg, .mpeg

Playable Subtitle format

SubRip(*.srt/*.txt)
SAMI(*.smi)
SubStation Alpha(*.ssa/*.txt)
MicroDVD(*.sub/*.txt)
SubViewer 1.0(*.sub)
SubViewer 2.0(*.sub/*.txt)
TMPlayer(*.txt)

Playable Codec format

“DIVX3.xx”, “DIVX4.xx”, “DIVX5.xx”, “XVID”,
“MP43”, “3IVX”.

Playable Audio format

“Dolby Digital”, “DTS”, “PCM”, “MP3”, “WMA”.

• Sampling frequency: within 8 - 48 kHz (MP3),
within 32 - 48kHz (WMA)

• Bit rate: within 8 - 320kbps (MP3),
32 - 192kbps (WMA)

• Not all the WMA Audio format is compatible with
this unit.

20

Controlling other TVs with the

Remote Control

You can control the sound level, input source, and

power switch of your LG TV with the supplied Remote
Control.

You can control the sound level, input source, and
power switch of non-LG TVs as well. If your TV is
listed in the table below, set the appropriate
manufacturer code.

1. While holding down TV POWER button, press the
number buttons to select the manufacturer code
for your TV (see the table below).

2. Release TV POWER button.

Code numbers of controllable TVs

If more than one code number is listed, try entering
them one at a time until you find the one that works
with your TV.

Manufacturer Code Number

LG / GoldStar 1 (Default), 2

Zenith 1, 3, 4

Samsung 6, 7

Sony 8, 9

Hitachi 4

Notes:

Depending on your TV, some or all buttons may not

•

function on the TV, even after entering the correct
manufacturer code.

• If you enter a new code number, the code number

previously entered will be erased.

• When you replace the batteries of the remote, the

code number you have set may be reset to the
default setting. Set the appropriate code number
again.

Maintenance and Service

Refer to the information in this chapter before
contacting a service technician.

Handling the Unit

When shipping the unit

Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally packed
at the factory.

Keeping the exterior surfaces clean

• Do not use volatile liquids such as insecticide
spray near the unit.

• Do not leave rubber or plastic products in contact
with the unit for a long period of time. since they
leave marks on the surface.

Cleaning the unit

To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution.

Do not use strong solvents such as alcohol, benzine,
or thinner, as these might damage the surface of the
unit.

Maintaining the Unit

The unit is a high-tech, precision device. If the optical
pick-up lens and disc drive parts are dirty or worn, the
picture quality could be diminished.

Depending on the operating environment, regular
inspection and maintenance are recommended after
every 1,000 hours of use.

For details, please contact your nearest authorized
service center.

Reference

Installation and

Setup

Introduction

21

Operation

Reference

Area Code

Afghanistan AF
Argentina AR
Australia AU
Austria AT
Belgium BE
Bhutan BT
Bolivia BO
Brazil BR
Cambodia KH
Canada CA
Chile CL
China CN
Colombia CO
Congo CG
Costa Rica CR
Croatia HR
Czech Republic CZ
Denmark DK
Ecuador EC
Egypt EG
El Salvador SV

Area Code

Ethiopia ET
Fiji FJ
Finland FI
France FR
Germany DE
Great Britain GB
Greece GR
Greenland GL
Herd and Mcdonald Islands

HM
Hong Kong HK
Hungary HU
India IN
Indonesia ID
Israel IL
Italy IT
Jamaica JM
Japan JP
Kenya KE
Kuwait KW
Libya LY
Luxembourg LU

Area Code

Malaysia MY
Maldives MV
Mexico MX
Monaco MC
Mongolia MN
Morocco MA
Nepal NP
Netherlands NL
Netherlands Antilles AN
New Zealand NZ
Nigeria NG
Norway NO
Oman OM
Pakistan PK
Panama PA
Paraguay PY
Philippines PH
Poland PL
Portugal PT
Romania RO
Russian Federation RU

Area Code

Saudi Arabia SA
Senegal SN
Singapore SG
Slovak Republic SK
Slovenia SI
South Africa ZA
South Korea KR
Spain ES
Sri Lanka LK
Sweden SE
Switzerland CH
Taiwan TW
Thailand TH
Turkey TR
Uganda UG
Ukraine UA
United States US
Uruguay UY
Uzbekistan UZ
Vietnam VN
Zimbabwe ZW

Area Codes

Choose a Area code from this list.

Language Code

Abkhazian 6566
Afar 6565
Afrikaans 6570
Albanian 8381
Ameharic 6577
Arabic 6582
Armenian 7289
Assamese 6583
Aymara 6588
Azerbaijani 6590
Bashkir 6665
Basque 6985
Bengali; Bangla 6678
Bhutani 6890
Bihari 6672
Breton 6682
Bulgarian 6671
Burmese 7789
Byelorussian 6669
Cambodian 7577
Catalan 6765
Chinese 9072
Corsican 6779
Croatian 7282
Czech 6783
Danish 6865
Dutch 7876
English 6978
Esperanto 6979
Estonian 6984
Faroese 7079

Language Code

Fiji 7074
Finnish 7073
French 7082
Frisian 7089
Galician 7176
Georgian 7565
German 6869
Greek 6976
Greenlandic 7576
Guarani 7178
Gujarati 7185
Hausa 7265
Hebrew 7387
Hindi 7273
Hungarian 7285
Icelandic 7383
Indonesian 7378
Interlingua 7365
Irish 7165
Italian 7384
Japanese 7465
Javanese 7487
Kannada 7578
Kashmiri 7583
Kazakh 7575
Kirghiz 7589
Korean 7579
Kurdish 7585
Laothian 7679
Latin 7665
Latvian, Lettish 7686

Language Code

Lingala 7678
Lithuanian 7684
Macedonian 7775
Malagasy 7771
Malay 7783
Malayalam 7776
Maltese 7784
Maori 7773
Marathi 7782
Moldavian 7779
Mongolian 7778
Nauru 7865
Nepali 7869
Norwegian 7879
Oriya 7982
Panjabi 8065
Pashto, Pushto 8083
Persian 7065
Polish 8076
Portuguese 8084
Quechua 8185
Rhaeto-Romance 8277
Rumanian 8279
Russian 8285
Samoan 8377
Sanskrit 8365
Scots Gaelic 7168
Serbian 8382
Serbo-Croatian 8372
Shona 8378
Sindhi 8368

Language Code

Singhalese 8373
Slovak 8375
Slovenian 8376
Somali 8379
Spanish 6983
Sudanese 8385
Swahili 8387
Swedish 8386
Tagalog 8476
Tajik 8471
Tamil 8465
Tatar 8484
Telugu 8469
Thai 8472
Tibetan 6679
Tigrinya 8473
Tonga 8479
Turkish 8482
Turkmen 8475
Twi 8487
Ukrainian 8575
Urdu 8582
Uzbek 8590
Vietnamese 8673
Volapük 8679
Welsh 6789
Wolof 8779
Xhosa 8872
Yiddish 7473
Yoruba 8979
Zulu 9085

Language Codes

Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.

22

Troubleshooting

Specifications

General

Power requirements: AC 120 V , 60 Hz

Power consumption: 8 W

Dimensions (Approx.):

430 x 35 x 242 mm (17 x 1.4 x 9.5 inches)
(W x H x D) without foot

Weight (Approx.): 1.9 kg (4.1 lbs)

Operating temperature:

5 °C to 35 °C (41 °F to 95 °F)

Operating humidity: 5 % to 90 %

Outputs

VIDEO OUT:

1 V (p-p), 75 Ω, sync negative, RCA jack x 1

S-VIDEO OUT:

(Y) 1.0 V (p-p), 75 Ω, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 Ω

COMPONENT VIDEO OUT:

(Y) 1.0 V (p-p), 75 Ω,negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2

AUDIO OUT:

2.0 Vrms (1 KHz, 0 dB), 600 Ω, RCA jack (L, R) x 1

DIGITAL OUT (COAXIAL):

0.5 V (p-p), 75 Ω, RCA jack x 1

System

Laser:

Semiconductor laser, wavelength 650 nm

Signal system: NTSC

Frequency response:

DVD (PCM 96 kHz): 8 Hz to 44 kHz
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz

Signal-to-noise ratio:

More than 100 dB (ANALOG OUT connectors only)

Harmonic distortion: Less than 0.008%

Dynamic range:

More than 95 dB (DVD/CD)

Accessories:

Video cable (1), Audio cable (1), Remote control (1),
Batteries (2

)

Note: Design and specifications are subject to change prior notice.

Symptom

No power.

The power is on, but
the DVD player does
not work.

No picture.

No sound.

The DVD player does
not start playback.

The Remote Control

does not work properly.

Possible Cause

• The power cord is disconnected.

• No disc is inserted.

• The TV is not set to receive DVD
signal output.

• The video cable is not connected
securely.

• The equipment connected with the
audio cable is not set to receive DVD
signal output.

The power of the equipment connected

•
with the audio cable is turned off.

• The AUDIO options are set to the
wrong position.

• An unplayable disc is inserted.

• The rating level is set.

• The

Remote Control is not pointed at

the remote sensor on the DVD player.

• The Remote Control

DVD player.

is too far from the

Correction

• Plug the power cord into the wall outlet
securely.

• Insert a disc. (Check the disc indicator
in the display window is lit.)

• Select the appropriate video input
mode on the TV.

• Connect the video cable securely.

• Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD player.

• Turn on the equipment connected with
the audio cable.

• Set the AUDIO option to the correct
position, then turn on the DVD player
again by pressing POWER.

• Insert a playable disc. (Check the disc
type and regional code.)

• Change the rating level.

• Point the Remote Control

sensor of the DVD player.

• Operate the Remote Control

the DVD player.

at the remote

closer to

Zenith will repair or replace your product, at Zenith’s option, if it proves to be defective in material or workmanship under
normal use, during the warranty period (“Warranty Period”) listed below, effective from the date (“Date of Purchase”) of
original consumer purchase of the product. This warranty is good only to the original purchaser of the product and
effective only when used in the United States, excluding U.S. Territories.

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE
EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS
WARRANTY PERIOD ABOVE. ZENITH WILL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR
INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS, IN CONNECTION WITH
THE PRODUCT. SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS
OR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY DOES NOT APPLY TO:

1.Damages or operating problems that result from shipping, installation, adjustment of user controls, calibration,
maintenance or failure to maintain, or separate system components; and

2.Damages or operating problems that result from normal wear and tear, misuse, abuse, operation outside
environmental specifications or contrary to the requirements or precautions in the Operating Guide, accident,
lightning strikes or other natural causes, unauthorized modification or alteration, incorrect electrical current or
voltage, software errors that do not disable functionality, operating software protocols adopted after the date of
manufacture or for outside the U.S., institutional or commercial use, or other causes not arising out of defect in
material or workmanship.

3.Therefore, the cost of repair or replacement of such a defective product shall be borne by the
consumer.

CUSTOMER INTER-ACTIVE CENTER NUMBERS:

FOR WARRANTY SERVICE:

You must call 1-800-243-0000 (24 hours a day, 365 days per year) and select appropriate option from the menu to
confirm the product is defective and to obtain Return Authorization (RA). During the Warranty Period, Zenith will
send you a return-shipping label. After you obtain RA for return, please box your unit with a copy of the sales receipt
and enough packing material to ensure undamaged delivery of your product. When you receive the label, place it on
the box and call the 800 # in the instruction for pick-up. When your unit is received, Zenith will repair or replace your
unit in accordance with this Limited Warranty.

ADVANCE SHIPMENT If replacement unit is available and you want second day delivery, our service representative
will ask for your credit card number. Zenith requires a reserved deposit by credit card as surety for such advance
shipment. Your credit card will not be charged if you return the defective unit in 10 business days. For advance
shipment, the return label will come with the replacement unit sent to you. Please follow boxing and shipping
instructions above.

Marketed and distributed by: GS# 3834RD0081K
LG ELECTRONICS U.S.A., INC. Printed in Indonesia
1000 SYLVAN AVENUE Issue O
ENGLEWOOD CLIFFS, NJ

WARRANTY PERIOD:
LABOR: 90 DAYS from the Date of Purchase.
PARTS: ONE YEAR from the Date of Purchase.
Repaired or Replacement Units are warranted for

the remaining period of the original warranty.

HOW SER

VICE IS HANDLED:

Call 1-800-243-0000 for instructions on getting the

defective unit repaired or replaced.
PPlease retain dated sales receipt and your box to

return the unit to Zenith for repair or replacement.
Both ways shipping charges will be borne by Zenith

during the Warranty Period. After the Warranty Period,
you pay in-bound shipping charges and Zenith pays
return shipping charges.

ZENITH ELECTRONICS USA., INC.

DVD PLAYER LIMITED WARRANTY-USA

For Warranty Service

For Post Warranty Repair

For Where-to buy, Product
Assistance, or Customer Assistance

Call 1-800-243-0000 (24 hours a day, 365 days per year)

Retain your dated sales receipt to prove the Date of Purchase as well as
your box for shipping the unit to Zenith, for warranty service.

Legible copy of your sales receipt must be submitted with the unit at the
time the unit is returned for warranty service.

For repair or replacement after the Warranty Period has expired,

Call 1-800-243-0000 (24 hours a day, 365 days per year)

Call 1-800-243-0000 (24 hours a day, 365 days per year) and select an

appropriate option from the menu.Or visit our website at

http://www.zenithservice.com