Zebra Technologies TW522 User Manual

TS-524 Switch and TW-5xx WallPlate

Installation Guide

(2)

TS-524 UTP ports 1 x RJ21 for PBX connection, 1 x RJ21 for downstream VDSL2

TS-524 Uplink ports 2 x IEEE 802.3 10/100/1000MB auto-sensing via RJ45

TS-524 Management Telnet, SSH, HTTPS, or serial console

TS-524 VLANs 802.1 Q tagged VLANs, access or trunk

*Operating frequencies and transmit power settings depend on national regulatory limits.

4dBi peak @ 2.4GHz, 5dBi @ 5GHz
Two internal omni-directional, 1x2 or 2x2 MIMO operation

*

1 to 20dBm in 1dBm increments

5GHz: 5150 to 5250MHz, 5725 to 5850MHz

2.4GHz: 2400 to 2483.5MHz

802.11ac: MCS 0-9, up to 400Mbps (TW-522 only)

802.11n: MCS 0-15, up to 300Mbps

802.11a: 6, 9, 12, 18, 24, 36, 48, 54Mbps

802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps

802.11ac (TW-522 only)

TW-522: Dual radio; 802.11a/b/g/n/ac; 2.4GHz and 5GHz

*

Antenna configuration

Transmit power settings

Operating frequencies

Data rates 802.11b: 1, 2, 5.5, 11Mbps

Network Standards 802.11a/b/g/n, 802.11i, 802.11-2007,

Medium DSSS, OFDM, MIMO

Pass through phone port Filtered RJ11 port

Uplink UTP 1 x VDSL2 via RJ11

LAN Ethernet port 2 x IEEE 802.3 10/100MB auto-sensing via RJ45

Wireless Interface TW-511: Single radio; 802.11a/b/g/n; 2.4GHz or 5GHz

*

TS-524 and TW-5xx Specifications

(1)

(0° to 40°C / 32° to 104°F except TW-522 which is 0° to 35°C / 32° to 95°F).
equipment operation specifications

• Verify there is adequate ventilation around the device, and that ambient temperatures meet

• Verify proper wiring and grounding for each installation location .

• Remove jewelry and watches before installing this equipment.

installation before installing this equipment.

• Read all installation instructions and site survey reports, and verify correct equipment

• This equipment should only be installed by qualified professional installers.

October 2015 Revision C
MN001390A01

Warnings

personal injury or equipment damage.
WARNING! Indicates a condition or procedure that could result in

loss or equipment malfunction.
CAUTION Care is required. Disregarding a caution can result in data

NOTE Tips, hints, or special requirements that you should take note of.

The following graphical alerts are in this document to indicate notable situations:

Lincolnshire, IL 60069 USA
Zebra Technologies Corporation

Document Conventions

TW-511 (P/N TW-0511-60010-US, -EU, -WR), and TW-510 (P/N TW-0510-WR).
TW-522 (P/N TW-0522-67030-US, -EU, -WR),
This installation guide applies to TS-524 (P/N TS-0524-WR),

structured cabling.
and wireless LAN networks without the effort and expense of re-wiring with
TW-5xx is designed to leverage the in-building telephone wiring to deploy Ethernet
such as hotels, healthcare facilities, apartments, and dormitory housing. The
The TW-5xx Series Wired/Wireless WallPlate is designed for multi-tenant buildings

Introduction

Installing In-line Filters

The TW-5xx Wallplate features a built-in Plain Old Telephone Setvice (POTS) and Line Power
filter for the desk phone. Install an in-line filter on all other phone jacks that will have a phone
connected.

The terminated filter has a clipped RJ11 connector. This is purposely done to comply with
EN60950 requirements. Use a small flat blade screwdriver to lift the tab if attempting to
remove the filter.

If installing a filter on a bathroom phone, use the unterminated filter. Remove the bathroom
wall plate and terminate the filter in the wall box using wire beans.

Installing the TW

-5xx WallPlate

1. Loosen the screws on the existing wall plate to create a gap of 6mm (1/4 in).

2. Attach the mounting adapter using the keyhole slots.

3. Tighten the screws until the mounting adapter is securely attached.

CAUTION Do not over tighten.

4. Connect the supplied 10cm cable between the TW-5xx bottom mounted RJ11
jack and the existing RJ11 jack.

5. Hook the bottom tabs on the mounting adapter to the TW-5xx. Rotate and
snap the TW-5xx onto the adapter.

Network Configuration (TS-524)

The following will enable all ports and configure one wireless LAN:

Serial Console Connection Default IP Address

Speed: 19200
Data Bits: 8
Parity: None
Stop Bit: 1
Flow Control: None

Log in to the system using Telnet, SSH, HTTP, or Serial Console using the default
username and password:

Username: admin
Password: admin123

Enter the following commands:

config
password admin <enter your new password>
country-code <xx = your country>
hostname <enter your hostname>
interface vlan1 ip-address 192.168.1.1/24
wlan Guest
exit
int dsl1-24 no shutdown
int radio1-24.1
channel 6
power 18
wlan Guest
no shutdown
exit

192.168.1.3

Enabling Line Power

Line power should be enabled after the filters and TW-5xx WallPlate have been
installed. Line power is safe for use with telephony equipment but it will ring the
phones if the filters are not installed first.

To enable line power, enter the following commands into the CLI:

interface dsl1-24 line-power
write memory

Regulatory Information

This guide applies to Model Numbers: TS-524, TW-510, TW-511, and TW-522.
All Zebra devices are designed to be compliant with rules and regulations in locations where they are sold

and will be labeled as required.
Local language translations are available at the following website:

www.zebra.com/support

Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user's
authority to operate the equipment. When Zebra devices are professionally installed, the Radio Frequency
Output Power will not exceed the maximum allowable limit for the country of operation.

Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas,
modifications, or attachments could cause damage and may violate regulations.

Radio Modules

The TW-511 contains an approved radio module. This module is identified below:

802.11 a/b/g/n WLAN, Type: TW-5

Wireless Device Country Approvals (TW-511 and TW-522 Only)

Regulatory markings, subject to certification, are applied to the device sign ifying the radio(s) is/are approved
for use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe.

Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at

www.zebra.com/doc

Note: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg,
Malta, Netherlands, Norway, Poland, Portugal, R omania, Slovak Republic, Slovenia, Spain, Sweden,
Switzerland and the United Kingdom.

Country Selection

Select only the country in which you are using the device. Any other selection will make the operation of this
device illegal. The US version of the Access Point will operate only if US country code is selected. The US
version will be sold / used in the US protectorates: American Samoa, Guam, Northern Marianas, Puerto Rico ,
US Virgin Islands.

.

.

Operation of the device without regulatory approval is illegal.

(3) (4) (5) (6)

Frequency of Operation - FCC and IC

5 GHz Only

The use in the UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250 MHz) is restricted to
Indoor Use Only; any other use will make the operation of this device illegal.

Industry Canada Statement:
Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potent ial for harmful

interference to co-Channel mobile satellite systems. High power radars are allocated as primary users
(meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause
interference and/or damage to LE-LAN devices.

Avertissement: Le dispositive fon ctionnant dans la bande 5150-5250 MHz est rés ervé uniquement pour une
utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux.

Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la
priorité) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage
et/ou des dommages aux dispositifs LAN-EL

2.4 GHz Only

The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is
limited by firmware.

Health and Safety Recommendations

General Safety Warnings

TS-524 Only
WARNIN G: For installation only in a Restricted Access Location by trained service personnel.
WARNIN G: Equipment must be connected to an earthed mains socket-outlet.
WARNIN G: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
WARNIN G: Voltages present which are above TNV-3 (POTS) limits. A cover must be installed over the punch

down blocks with a HV (High Voltage) warning label (supplied).
WARNIN G: The maximum operating ambient temperature is 40 degrees Celcius. When installing the Switch

in an equipment rack, consider the following potential hazards:
Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly, the operating

ambient temperature of the rack environment may be greater than the room ambient. Therefore
consideration should be given to installing the equipment in an environment compatible with t he
manufacturer's maximum rated ambient temperature (Tmra).

Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required
for safe operation of the equipment is not compromised.

Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is
not achieved due to uneven mechanical loading.

Circuit Overloading - Consideration should be given to the connection of the equipmen t to the supply circuit
and the effect that overloading of circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention
should be given to supply connections other than direct connections to the branch circuit (e.g.,use of power
strips).

(7) (9) (1 1) (13)

RF Exposure Guidelines (TW-511 and TW-522 Onl y)

Safety Information
Reducing RF Exposure - Use Properly

Only operate this device in accordance with the instructions supplied.

International (TW-511 and TW-522 Only)

The device complies with internationally recognized standards covering human exposure to electromagnetic
fields from radio devices. For information on "International" human exposure to electromagnetic fields refer
to the Declaration of Conformity (DoC) at www.zebra.com/doc

For further information on the safety of RF energy from wireless devices, see
http://responsibility.zebra.com/index.php/downloads/ located under Wireless Communications and Health

EU (TW-511 and TW-522 Only)

Remote and Standalone Antenna Configurations

To comply with EU RF exposure requirements, antennas that are mounted externally at remote locations or
operating near users at stand-alone desktop of similar configurations must operate with a minimum
separation distance of 20 cm from all persons.

US and Canada (TW-511 and TW-522 Only)

Co-located statement

To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be
co-located or operating in conjunctio n with any other transmitter/antenna except those already approved in
this filling.

Remote and Standalone Antenna Confiugrations

To comply with FCC RF exposure requirements, antennas that are mounted externally at remote locations or
operating near users at stand-alone desktop of similar configurations must operate with a minimum
separation distance of 20 cm from all persons.

Radio Frequency Interference Requirements - FCC

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be re quired to correct the
interference at his own expense.

Radio Transmitters (Part 15) - (TW-511 and TW-522 Only)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Radiation Exposure Statement

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Déclaration
d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements FCC et IC établies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

.

Waste Electrical and Electronic Equipment (WEEE)

English: For EU Customers: All products at the end of their life must be returned to Zebra
for recycling. For information on how to return product, please go to: www.zebra.com/weee

Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent
être retournés à Zebra pour recyclage. Pour de plus amples informations sur le retour de
produits, consultez : www.zebra.com/weee
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a
Zebra al final de su ciclo de vida para que sean reciclados. Si desea más información
sobre cómo devolver un producto, visite: www.zebra.com/weee

Български: За клиенти от ЕС: След края на полезния им живот всички продукти
трябва да се връщат на Zebra за рециклиране. За информация относно връщането
на продукти, моля отидете на адрес: www.zebra.com/weee

Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer
Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter www.zebra.com/weee
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di
vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni
sulle modalità di restituzione, visitare il seguente sito Web: www.zebra.com/weee
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à
Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite:

www.zebra.com/weee

Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun
levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg

www.zebra.com/weee

Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y
zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów
znajduj¹ siê na stronie internetowej www.zebra.com/weee
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti
vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na
webové stránce: www.zebra.com/weee
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise
eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun
aadressi: www.zebra.com/weee
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell
eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos
tudnivalókért látogasson el a www.zebra.com/weee

.

voor meer informatie over het terugzenden van producten.

.

.

.

.

.

.

.

.

weboldalra.

Japan (VCCI) - Voluntary Control Council for Interference

.

Chinese Warning Statement for Class A ITE

Other Countries
Australia

Use of 5 GHz RLAN's in Australia is restricted in the following band 5.50 - 5.65GHz.

Brazil
Declarações Regulamentares para TW-511 - Brazil

Nota: A marca de certificação se aplica ao Transceptor, modelo TW-511. Este equipamento opera em caráter
secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo
tipo, e não pode causar interferência a sistemas operando em caráter primário.
Para maiores informações sobre ANATEL consulte o site: www.anatel.gov.br

Mexico
Mexico

Restrict Frequency Range to: 2.450 - 2.4835 GHz.
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o
dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier
interferencia, incluyendo la que pueda causar su operación no deseada.

Product designed to be used below 2000 meters altitude.

TW-510, TW-511 and TW-522

When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub,
in a wet basement or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk
of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

Warnings for Use of Wireless Devices

Please observe all

Potentially Hazardous Atmospheres - Fixed Installations

You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical
plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders).

Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When
installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely
affected.

Pacemakers

Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a
handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These
recommendations are consistent with independent research and recommendations by Wireless Technology
Research.

Persons with Pacemakers:

• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.

• Should not carry the device in a breast pocket.

• Should use the ear furthest from the pacemaker to minimize the potential for interference.

• If you have any reason to suspect that interference is taking place, turn OFF your device.

Other Medical Devices

Please consult your physician or the manufacturer of the medical device, to determine if the operation of your
wireless product may interfere with the medical device.

warning notices with regard to the usage of wirel ess devices.

Safety in Hospitals

The use of 5 GHz WLAN's, for use in the US , have the following restrictions

• Notched Band 5.60 - 5.65 GHz

Radio Frequency Interference Requirements - Canada

This Class A digital apparatus complies with Canadian ICES-003.

Radio Transmitters - (TW-511 and TW-522 Only)
For RLAN Devices:

The use of 5 GHz RLAN's, for use in Canada, have the following restrictions:

• Restricted Band 5.60 - 5.65 GHz

L'utilisation de RLAN de 5 GHz, pour utilisation au Canada est soumise aux restrictions suivantes:

• Bande Restreinte de 5,60 à 5,65 GHz
This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de
licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible
de provoquer un fonctionnement indésirable.

Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical
specifications were met.

Marking and European Economic Area (EEA)

WARNIN G: This is a Class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.
The use of 2.4GHz RLAN's, for use through the EEA, have the following restrictions:

• Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz.

• Italy requires a user license for outside usage.

Statement of Compliance for Wireless Devices (TW-511 and TW-522 Only)

Zebra hereby declares that this device is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from

www.zebracom/doc

Statement of Compliance for Non-Wireless Devices (TS-524 and TW-510)

Zebra hereby declares that this device is in compliance with all the applicable Directives, 2004/108/EC and
2006/95/EC. A Declaration of Conformity may be obtained from

www.zebracom/doc

Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras
till Zebra för återvinning. Information om hur du returnerar produkten finns på

www.zebra.com/weee

Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen
palauttamisesta on osoitteessa www.zebra.com/weee
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er
udtjent. Læs oplysningerne om returnering af produkter på: www.zebra.com/weee

Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους,
πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες
σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση

www.zebra.com/weee

Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom,
iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna
l-prodott, jekk jogħġbok żur: www.zebra.com/weee
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare,
trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre returnarea produsului,
accesaţi: www.zebra.com/weee
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju
Zebra za reciklažo. Za informacije o vračilu izdelka obiščite: www.zebra.com/weee
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich
životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov
nájdete na: www.zebra.com/weee
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti
utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite:

www.zebra.com/weee

Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ
Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu,
skatiet: www.zebra.com/weee
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için
Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi
ziyaret edin: www.zebra.com/weee

.

.

.

στο ∆ιαδίκτυο.

.

.

.

.

.

.

.

Turkish WEEE Statement of Compliance

Support

If you have a problem with your equipment, contact support for your region.

Contact information is available at: www.zebra.com/support

When contacting Support, please provide the following information:

• Serial number of the unit

• Model number or product name

• Software type and version number

Support responds to calls by e-mail, telephone, or fax within the time limits set forth
in support agreements. If you purchased your product from a business partner,
contact that business partner for support.

Web Site

The Support Web site, located at:www.zebra.com/support provides information and
online assistance including developer tools, software downloads, product manuals
and online repair requests.

Manuals

www.zebra.com/support

.

(8) (10) (12) (14)