There are two software elements that you can use to control the functionality of the iX104C
Bios Setup Utility and Panel Control Center.
• Bios Setup Utility controls the default boot up settings
• Panel Control Center allows for temporary session based settings via the programmable keys.
BIOS Setup Utility
1. Controls:
The Control for the Dual Mode system can be found in Bios Setup Utility under the Startup
Configuration in the Digitizer Section:
Dual Mode:
Digitizer Selection values and meanings
Digitizer Selection Description Notes
Auto Xplore’s Auto Sensing feature is enabled allow for
automatic sensing of the active pen or Touch inp uts.
The system manages the input method seamlessly
without user intervention
Touch Only Turns on Touch input only. Active Digitizer and pen
as well as the Auto Sense feature are disabled
Digitizer Only Turns on Active Pen input only. Touch Panel and
Auto Sense features are disabled.
Copyright XPLORE TECHNOLOGIES 1 of 6
This is the default setting
For iX104C2 and iX104C2V this
is the default setting and cannot
be changed
2. Security:
To allow or disallow User control of the input method use the Bios Setup Utility Supervisor
password.
Password Setting Description Notes
No passwords set Control can be changed by
anyone
Supervisor password set only Control can be only changed by
entering Supervisor password
User Password set Controls are disabled Only the supervisor can change digitizer
This control is not controlled by Windows
User groups
The password will be prompted prior to
Bios Setup Utility will open
controls
3. Changing values:
Anytime the value is changed the Bios Setup Utility will prompt for the unit to be rebooted when the
OK button is clicked. It is strongly recommended to reboot the system after changing this value.
This value will now be the default input mode.
Panel Control Center
Panel Control Center allows for temporary, session-based changes to iX104C2 Dual Mode unit functions.
Upon a reboot or a restart of the system these settings are lost and the default value set in BIOS SETUP
UTILITY are restored.
By default these controls are not set by Panel Control Center and will need to set by the Administrator
account of the tablet. (Any user that has administrator rights). The functions will be dependent on the value
set in the Bios Setup Utility.
To setup, click on Panel Control Center (triangle icon in the System Tray)
> Click on the configure button
> Click the Change Button next to the P Key desired and
> Choose Predefined Function as shown below
Copyright XPLORE TECHNOLOGIES 2 of 6
There are two pre-defined functions; Digitizer Selection and Touch Panel Toggle.
Pre-Define Function Description
Digitizer Selection This will toggle from AUTO to Digitizer Only to Touch Only, when Bios Setup Utility is
set to AUTO.
Touch Panel Toggle This will disable the Touch Panel if you desire to turn off the Touch input temporarily
when in the Touch only or Auto Modes.
Since the above Pre-defined functions are dependent on the Bios Setup Utility, the following chart show the
functions and results:
Bios Setup
Digitizer
Selection Value
Digitizer Only
Pre-Define Function On-Screen Description
when key is pressed
Digitizer Selection
Digitizer Only will display
Notes
Since Digitizer only is
selected there is no other
input available. Digitizer is
left functioning.
Copyright XPLORE TECHNOLOGIES 3 of 6
Bios Setup
Digitizer
Selection Value
Digitizer Only
Bios Setup
Digitizer
Selection Value
Touch Only
Pre-Define Function On-Screen Description
when key is pressed
Touch Screen Toggle
Digitizer Only will display
Pre-Define Function On-Screen Description
when key is pressed
Digitizer Selection
Touch Only will display
Notes
Touch Screen is disabled
already.
Notes
Since Touch only is selected
there is no other input
available Touch is left
functioning.
Copyright XPLORE TECHNOLOGIES 4 of 6
Bios Setup
Digitizer
Selection Value
Touch Only
Pre-Define Function On-Screen Description
when key is pressed
Touch Screen Toggle
Touch Screen Off/On
Notes
This will turn on or off the
Touch Screen. Note, if
touch screen is off and unit
goes into standby or
hibernate Touch Screen will
automatically be turned back
on.
Bios Setup
Digitizer
Selection Value
Auto
Pre-Define Function On-Screen Description
when key is pressed
Digitizer Selection
Auto, Digitizer only or Touch
only
Notes
This rotates through each
mode and displays that
mode
Copyright XPLORE TECHNOLOGIES 5 of 6
Bios Setup
Digitizer
Selection Value
Auto
Pre-Define Function On-Screen Description
when key is pressed
Touch Screen Only
Auto or Digitizer Only
Notes
This function turns on or off
the touch panel.
Examples of implementation:
Sample 1
Power users or limited users to have Touch only with the ability to turn off the touch screen. Users do not
have option to change any controls.
Setup:
1. Set a Supervisor password in Bios Setup utility. (This will protect the digitizer selection, for that
matter all bios setup utility controls)
2. Set one of the P Keys to Touch Panel Toggle in Administrator mode (Windows)
3. Create User Account (Add new user). Or if user is already created the setting the admin has set
will replicate to all users on the unit.
Sample 2
Power user or limited users to default to Auto Sense but allow temporary selection. Users have the option
to change the default.
Setup:
1. Do not set a Supervisor password (leave open)
2. Set one of the P Keys to Digitizer Selection
3. Create User Account (add new User)
Copyright XPLORE TECHNOLOGIES 6 of 6
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.