Contents of the box:
Features: Back and Ports
Features: The Battery Compartment
Getting Started
The WORKABOUT PRO
Features: Front
Speaker
Stylus
3
H
a
n
d
-
H
e
l
d
C
o
m
p
u
t
e
r
C
Ve
r
s
i
o
n
Q
u
i
c
k
S
t
a
r
t
G
February 8, 2010 PN 8000198.A
u
i
d
e
I
S
O
9
0
0
1
C
e
r
t
i
f
i
e
d
Q
u
a
li
t
y
M
a
n
a
g
e
m
e
n
t
S
y
s
t
e
m
This Guide
Microphone Port
Additional documentation
(dependent on order)
Scan Bar
LED
Indicator
Battery Cover
Back Cover
Endcap
Stylus
Features: Typical Variants
Version without
scanner or
GSM radio
Version with scanner
in pod
Version with GSM
radio and scanner
in endcap
Version with pistol grip
Tether Port
Beeper Port
LIF Port
DC Input
Version with scanner
in endcap
Card Gate (Open)
Battery Fasteners
Card Gate (Closed)
FCC Labels
On/Off Switch
SIM Card Slot
Battery Cover
Note: The SIM Card slot
may be covered on your unit.
SD Card Slot
On/Off Switch
Switch the hardware on.
1
On/Off Switch
Insert the battery.
2
Close and lock
3
the battery cover.
ON
Battery Fasteners
Turn the fasteners towards
the centre of the unit
to lock the battery cover.
Over
Charge the battery. The power adaptor may
4
be plugged directly into the WORKABOUT PRO3.
Turn the unit on. Press the Power
5
button for a few seconds.
To turn the WORKABOUT PRO3 off, do one
of the following:
Press the • Power button, or
Select • Shut down from the Start menu.
Hand-Held Computer
C Version
The WORKABOUT PRO3 may also be charged
in a Docking Station.
Note: Use only the
universal AC power
adaptor approved by
Psion Teklogix for the
WORKABOUT PRO3.
Allow the WORKABOUT PRO3 to charge
for 6 hours.
Note: Full battery performance is
5 - 40°C
41 - 104°F
only reached after the rst few full
charge/discharge cycles.
6h
Quick Start Guide
Power Button
Resetting the unit
Important: Resetting may result in data loss.
February 8, 2010 PN 8000198.A
To perform a cold reset:
Connect the WORKABOUT PRO3 to the
6
host computer. Connect using a Tether Port to
USB cable, or through a Docking Station.
Install ActiveSync®.
7
Go to http://go.microsoft.com/fwlink/?LinkId=147001 and
follow the instructions to download and install
ActiveSync 4.5 or higher.
Note: ActiveSync is not needed when connecting to a
Press the • SCAN bar, the FN/BLUE key, and the ENTER key
simultaneously for a few seconds.
During a cold reset, running programs are halted and RAM
memory is cleared. The contents of ash memory and the
registry are preserved. The operating system is reloaded.
To perform a warm reset:
Press the • FN/BLUE key and the ENTER key simultaneously
for a few seconds.
During a warm reset, running programs are halted. The
contents of RAM, ash memory and the registry are preserved.
host computer that uses the Windows® Mobile Device
Center (such as Microsoft® Windows Vista®).
Congure ActiveSync. Follow the onscreen
8
instructions provided by ActiveSync to establish
a connection between the host computer and the
WORKABOUT PRO3.
8 0 0 0 1 9 8
Rev. A
ISO 9001 Certied
Quality Management System
Loading...