Introduction
M10X1.5X50 (4)
Screw
Split Lock Washer
Flat Washer
Mounting Bracket
M8X1.25X20 (2)
Screw
Split Lock Washer
Flat Washer
Note: Dependent on the desired
height, attach the U-Mount Bracket
to either the top or bottom hole
located on the Adapter Bracket.
Adapter
Bracket
Friction
Pad (2)
M6X1X14 Screw (4)
Scanner
Holder
Adapter
Bracket (2)
M6X1X14 (2)
M6X1X17 (2)
Scanner
Holder
Mounting
Bracket
M8X1.25X20 (2)
Screw
Split Lock Washer
Flat Washer
Friction
Pad (2)
This installation guide provides instruction on how to install the
Adapter Bracket Kit (P/N: MNT-VC80-ADPA1-1) to attach the VH10 or
the VC80 to the VC5090 U-Mount.
WARNING! The vehicle computer and bracket must be firmly
secured to a surface that can support the vehicle
computer’s weight.
Always use four 11mm holes with M10 screws
to mount the bracket to the desired location. Using
different holes and screws may cause damage
and/or injury.
CAUTION Mounts used in industrial or vibration generating
environments may be subjected to fatigue, stress,
and/or part wear. A periodic inspection of the
mounting hardware and mounts should be
performed to ensure parts are retightened to the
correct torque, free from fractures, excessive
wear, and/or other environmental damage. Any
parts found to be unsafe should be removed and
replaced immediately. After inspection or
replacement of parts, readjust the mount as
required.
Contents
The Adapter Bracket kit includes:
•
Adapter Bracket (quantity: 2)
•
Friction Pad (quantity: 2)
•
M6X1X14 screws and washers (quantity: 4 each)
•
M8X1.25X20 screws and washers (quantity: 2 each)
•
Installation guide (quantity: 1)
ADAPTER BRACKET KIT
FOR VC50 U-MOUNT
INSTALLATION GUIDE
Scanner Holder
The Scanner Holder attachment (P/N: KT-SCANMNT-VC80-R) is not
included in the Adapter Bracket kit and must be purchased separately.
To attach the Scanner Holder:
1. Install the Adapter Bracket on one side of VC using the M6X1X14
screws and washers.
2. Install the Adapter Bracket and Scanner Holder subassembly on
the other side of the VC using the M6X1X17 screws. Torque the
screws to 3.9 Nm (34.5 in-lbs).
Required Tools
•
Socket and Torque wrench for the M6, M8, and M10 screws.
Installation
WARNING! Always disconnect the VC from all battery and
A/C power before servicing components.
To install the Adapter Bracket:
1. Screw the Adapter Brackets onto the VC using the M6X1X14
screws and washers.
a. Insert the Split Lock Washer on the screw.
b. Insert the Flat Washer on the screw.
c. Torque the screws to 3.9 Nm (34.5 in-lbs).
2. Mount the Mounting Bracket in the desired location using the
M10X1.5X50 screws, split lock washers, and flat washers (not
included in the Adapter Bracket kit). Torque the screws to 42 Nm
(31 ft-lbs).
3. Place the Friction Pads onto the thread insert on the Adapter
Brackets.
4. Install the subassembly to the Mounting Bracket using the
Zebra Technologies Corporation, Inc.
3 Overlook Point
Lincolnshire, IL 60069, U.S.A.
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many
jurisdictions worldwide. All other trademarks are the property of their respective owners.
© 2016 Symbol Technologies LLC, a subsidiary of Zebra Technologies Corporation.
All rights reserved.
M8X1.25X20 screws and washers. Adjust the VC to the desired
angle. Torque the M8 screws to 27.0 Nm (239.0 in-lbs).
3. Mount the Mounting Bracket in the desired location using the
M10X1.5X50 screws and washers (not included in the Adapter
Bracket kit). Torque the screws to 42 Nm (31 ft-lbs).
4. Place the Friction Pads onto the thread insert on the Adapter
Brackets.
5. Install the subassembly to the Mounting Bracket using the
M8X1.25X20 screws and washers. Adjust the VC to the desired
angle. Torque the M8 screws to 27.0 Nm (239.0 in-lbs).
MN-002932-01 Rev A 10/2016
Loading...