TC2X
LED Button
LED 1LED 2LED 3LED 4
Charging Contacts
USB Port
(Charging Only)
Power Pack
Regulatory Guide
Printed in China
Zebra Technologies | 3 Overlook Point | Lincolnshire, IL
60069 USA www.zebra.com
©2017 ZIH Corp and/or its affiliates. All rights reserved. ZEBRA
and the stylized Zebra head are trademarks of ZIH Corp,
registered in many jurisdictions worldwide. All other trademarks
are the property of their respective owners.
MN-003121-02 Rev. A - 11/17
Introduction
The Extended Power Pack provides additional power
for charging the TC2X internal battery.
For best performance it is recommended that the
Power Pack should always be installed on the device
and that both the Power Pack and device are fully
charged at the start of each work shift.
Installation
Charging
• In a cradle
• In a cradle attached to the TC2X
• using Zebra USB-C cable.
Power Pack Charging
The Power Pack Charging LEDs indicate the status of
charging. See the table below for charging status. The
power pack charges from fully depleted to 90% in
approximately four hours and from fully depleted to
100% in approximately five hours.
Check Power Level
To check the power level of the power pack, press the
LED button. The LEDs light indicating the charge level.
After five seconds the LEDs turn off.
LED State
LED1 LED2 LED3 LED4 Indication
Off Off Off Off Not charging.
Flashing Off Off Off Charge level is
Solid Flashing Off Off Charge level is
Solid Solid Flashing Off Change level is
Solid Solid Solid Off Fully charged (95-
Off Off Off Flashing Charging error, e.g.:
between 0% and 33%.
between 33% and
66%.
between 66% and
95%.
100%).
• Temperature is too
low or too high.
• Charging has
gone on too long
without completion
(typically 10
hours).
• Overcurrent/
voltage protection.
Charging Temperature
Charge batteries in temperatures from 0°C to 50°C
(32°F to 122°F) and discharge in temperatures from
-10°C to 50°C (14°F to 122°F). The device or cradle
always performs battery charging in a safe and
intelligent manner. At higher temperatures (e.g.
approximately +37°C (+98°F)) the device or cradle may
for small periods of time alternately enable and disable
battery charging to keep the battery at acceptable
temperatures. The power pack indicates when charging
is disabled due to abnormal temperatures via its LED.
Input/Output Rating
Input (USB-C): 5V ⎓ 1.2 A (Max.)
Output (2,000 mAh):
5V ⎓ 1.4 A (Max.)
Regulatory Information
These devices are approved under Zebra Technologies
Corporation.
This guide applies to the following Model Number:
BT-000343.
All Zebra devices are designed to be compliant with the
rules and regulations in the locations they are sold and
will be labeled as required.
Local language translations are available at the
following website: www.zebra.com/support.
Any changes or modifications to Zebra equipment not
expressly approved by Zebra could void the user's
authority to operate the equipment.
Declared maximum operating temperature: 40°C.
For use only with Zebra approved and UL Listed mobile
computers.
Health and Safety
Recommendations
INSTRUCTIONS PERTAINING TO RISK OF FIRE OR
INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING - When using this product, basic
precautions should always be followed, including the
following:
1. Read all the instructions before using the product.
2. To reduce the risk of injury, close supervision is
necessary when the product is used near children.
3. Do not put fingers or hands into the product.
4. Do not expose power bank to rain or snow.
5. Use of a power supply or charger not
recommended or sold by power pack
manufacturer may result in a risk of fire or injury to
persons.
6. Do not use the power bank in excess of its output
rating. Overload outputs above rating may result in
a risk of fire or injury to persons.
7. Do not use the power bank that is damaged or
modified. Damaged or modified batteries may
exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
8. Do not disassemble the power bank. Take it to a
qualified service person when service or repair is
required. Incorrect reassembly may result in a risk
of fire or injury to persons.
9. Do not expose a power pack to fire or excessive
temperature. Exposure to fire or temperature
above 100°C (212°F) may cause explosion.
10. Have servicing performed by a qualified repair
person using only identical replacement parts.
11. This will ensure that the safety of the product is
maintained.
12. Switch off the power bank when not in use.
SAVE THESE INSTRUCTIONS
Ergonomic Recommendations
CAUTION In order to avoid or minimize the
potential risk of ergonomic injury, follow
the recommendations below. Consult
with your local Health and Safety
Manager to ensure that you are adhering
to your company's safety programs to
prevent employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy
reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Power Supply
Use ONLY a Zebra approved Nationally Recognized
Test Laboratory (NRTL) Certified ITE (LPS/SELV)
power supply with electrical ratings: Output 5 VDC, min
2.5 A, with a maximum ambient temperature of at least
40°C. Use of alternative power supply will invalidate
any approvals given to this unit and may be dangerous.
Batteries
Taiwan - Recycling
EPA (Environmental Protection
Administration) requires dry battery producing
or importing firms in accordance with Article
15 of the Waste Disposal Act are required to
indicate the recycling marks on the batteries used in
sales, giveaway, or promotion. Contact a qualified
Taiwanese recycler for proper battery disposal.
Battery Information
Caution: Risk of explosion if battery is replaced by an
incorrect type. Dispose of batteries according to
instructions.
Zebra approved rechargeable power packs are
designed and constructed to the highest standards
within the industry.
However, there are limitations as to how long a battery
can operate or be stored before needing replacement.
Many factors affect the actual life cycle of a battery
pack such as heat, cold, harsh environmental
conditions, and severe drops.
When batteries are stored over six months, some
irreversible deterioration in overall battery quality may
occur. Store batteries at half of full charge in a dry, cool
place, removed from the equipment to prevent loss of
capacity, rusting of metallic parts, and electrolyte
leakage. When storing batteries for one year or longer,
the charge level should be verified at least once a year
and charged to half of full charge.
Replace the battery when a significant loss of run time
is detected.
Standard warranty period for all Zebra batteries is one
year, regardless if the battery was purchased
separately or included as part of the mobile computer
or bar code scanner. For more information on Zebra
batteries, please visit: www.zebra.com/batterybasics.
Battery Safety Guidelines
The area in which the units are charged should be clear
of debris and combustible materials or chemicals.
Particular care should be taken where the device is
charged in a non-commercial environment.
• Follow battery usage, storage, and charging
guidelines found in the user's guide.
• Improper battery use may result in a fire, explosion,
or other hazard.
• To charge the mobile device battery, the battery
and charger temperatures must be between +32°F
and +104°F (0°C and +40°C).
• Do not use incompatible batteries and chargers.
Use of an incompatible battery or charger may
present a risk of fire, explosion, leakage, or other
hazard. If you have any questions about the
compatibility of a battery or a charger, contact
Zebra support.
• For devices that utilize a USB port as a charging
source, the device shall only be connected to
products that bear the USB-IF logo or have
completed the USB-IF compliance program.
• Do not disassemble or open, crush, bend or
deform, puncture, or shred.
• Severe impact from dropping any battery-operated
device on a hard surface could cause the battery to
overheat.
• Do not short circuit a battery or allow metallic or
conductive objects to contact the battery terminals.
• Do not modify or remanufacture, attempt to insert
foreign objects into the battery, immerse or expose
to water or other liquids, or expose to fire,
explosion, or other hazard.
• Do not leave or store the equipment in or near
areas that might get very hot, such as in a parked
vehicle or near a radiator or other heat source. Do
not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to promptly dispose
of used re-chargeable batteries.
• Do not dispose of batteries in fire.
• Seek medical advice immediately if a battery has
been swallowed.
• In the event of a battery leak, do not allow the liquid
to come in contact with the skin or eyes. If contact
has been made, wash the affected area with large
amounts of water and seek medical advice.
• If you suspect damage to your equipment or
battery, contact Zebra support to arrange for
inspection.
Radio Frequency Interference
Requirements-FCC
Note: This equipment
Tested to comply
with FCC Standards
FOR HOME OR OFFICE USE
the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio
communications. However there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
has been tested and
found to comply with
the limits for a Class
B digital device,
pursuant to Part 15 of
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV
technician for help.
Radio Frequency Interference
Requirements - Canada
CAN ICES-3 (B)/NMB-3(B)
CE Marking and European
Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this device is in compliance
with all applicable Directives, 2014/30/EU, 2014/35/EU
and 2011/65/EU.
The full text of the EU Declaration of Conformity is
available at the following internet address:
www.zebra.com/doc.
China
通过访问以下网址可下载当地语言支持的产品说明书
www.zebra.com/support
锂电池安全警示语 :
警告：请勿拆装，短路，撞击，挤压或者投入火中
注意：如果电池被不正确型号替换，或出现鼓胀，会存
在爆炸及其他危险
请按说明处置使用过的电池
电池浸水后严禁使用
合格证：
Turkish WEEE Statement of
Compliance
EEE Yönetmeliğine Uygundur
Waste Electrical and
Electronic Equipment
(WEEE)
English: For EU Customers: All products at the end of
their life must be returned to Zebra for recycling. For
information on how to return product, please go to:
www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné
po skonèení jejich životnosti vrátit spoleènosti Zebra
k recyklaci. Informace o zpùsobu vrácení produktu
najdete na webové stránce: www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til
Zebra til recirkulering, når de er udtjent. Læs
oplysningerne om returnering af produkter på:
www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte
müssen am Ende ihrer Lebensdauer zum Recycling an
Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter
www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea
lõppedes tagastada taaskasutamise eesmärgil Zebra'ile.
Lisainformatsiooni saamiseks toote tagastamise kohta
külastage palun aadressi: www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los
productos deberán entregarse a Zebra al final de su ciclo
de vida para que sean reciclados. Si desea más
información sobre cómo devolver un producto, visite:
www.zebra.com/weee.
Français: Clients de l'Union Européenne: Tous les
produits en fin de cycle de vie doivent être retournés à
Zebra pour recyclage. Pour de plus amples informations
sur le retour de produits, consultez : www.zebra.com/
weee.
Hrvatski: Za kupce u Europskoj uniji: Svi se proizvodi po
isteku vijeka trajanja moraju vratiti tvrtki Zebra na
recikliranje. Informacije o načinu vraćanja proizvoda
potražite na web-stranici: www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti
al termine del rispettivo ciclo di vita devono essere
restituiti a Zebra al fine di consentirne il riciclaggio. Per
informazioni sulle modalità di restituzione, visitare il
seguente sito Web: www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas
mūža beigām ir jānogādā atpakaļ Zebra otrreizējai
pārstrādei. Lai iegūtu informāciju par produktu
nogādāšanu Zebra, lūdzu, skatiet: www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų
eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją
„Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite:
www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement
terméket a Zebra vállalathoz kell eljuttatni
újrahasznosítás céljából. A termék visszajuttatásának
módjával kapcsolatos tudnivalókért látogasson el a
www.zebra.com/weee weboldalra.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu flaħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand
Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek
tirritorna l-prodott, jekk jogħġbok żur: www.zebra.com/
weee.
Nederlands: Voor klanten in de EU: alle producten
dienen aan het einde van hun levensduur naar Zebra te
worden teruggezonden voor recycling. Raadpleeg
www.zebra.com/weee voor meer informatie over het
terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty
wycofane z eksploatacji naleźy zwrócić do firmy Zebra w
celu ich utylizacji. Informacje na temat zwrotu produktów
znajdują się na stronie internetowej www.zebra.com/
weee.
Português: Para clientes da UE: todos os produtos no
fim de vida devem ser devolvidos à Zebra para
reciclagem. Para obter informações sobre como devolver
o produto, visite: www.zebra.com/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la
sfârşitul duratei lor de funcţionare, trebuie returnate la
Zebra pentru reciclare. Pentru informaţii despre
returnarea produsului, accesaţi: www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky
musia byť po uplynutí doby ich životnosti vrátené
spoločnosti Zebra na recykláciu. Bližšie informácie o
vrátení výrobkov nájdete na: www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po
poteku življenjske dobe vrniti podjetju Zebra za reciklažo.
Za informacije o vračilu izdelka obiščite: www.zebra.com/
weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki
tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön,
kun tuotetta ei enää käytetä. Lisätietoja tuotteen
palauttamisesta on osoitteessa www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som
uppnått sin livslängd måste returneras till Zebra för
återvinning. Information om hur du returnerar produkten
finns på www.zebra.com/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm
ürünler geri dönüştürme için Zebra'ya iade edilmelidir.
Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu
adresi ziyaret edin: www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο
τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται
στην Zebra για ανακύκλωση. Για περισσότερες
πληροφορίες σχετικά με την επιστροφή ενός προϊόντος,
επισκεφθείτε τη διεύθυνση www.zebra.com/weee στο
Διαδίκτυο.
Български: За клиенти от ЕС: След края на полезния
им живот всички продукти трябва да се връщат на
Zebra за рециклиране. За информация относно
връщането на продукти, моля отидете на адрес:
www.zebra.com/weee.
Warranty
For the complete Zebra hardware product warranty
statement, go to: www.zebra.com/warranty.
Service Information
Before you use the unit, it must be configured to
operate in your facility’s network and run your
applications.
If you have a problem running your unit or using your
equipment, contact your facility’s Technical or Systems
Support. If there is a problem with the equipment, they
will contact the Zebra Global Customer Support at
www.zebra.com/support.
For the latest version of this guide go to:
www.zebra.com/support.
CMM 披露
有害物质
部件名称
(Parts)
铅
汞
(Pb)
(Hg)镉(Cd)
金属部件
(Metal Parts)
电路模块
(Circuit Modules)
电缆及电缆组件
(Cables and Cable
Assemblies)
塑料和聚合物部件
(Plastic and
Polymeric Parts)
光学和光学组件
(Optics and
Optical
Components)
电池
(Batteries)
OOO O O O
XOO O O O
OOO O O O
OOO O O O
OOO O O O
OOO O O O
本表格依据 SJ/T 11364 的规定编制。
O:表示该有害物质在该部件所有均质材料中的含量均在
GB/T 26572 规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含
量超出 GB/T 26572 规定的限量要求。( 企业可在此处，
根据实际情况对上表中打 “×” 的技术原因进行进一步说
明。）
This table was created to comply with China RoHS
requirements.
六价铬
(Cr(VI))
(PBB)
多溴联苯
多溴二苯醚
(PBDE)
Loading...