STB20XX Single Slot Cradles
Quick Reference Guide
2 STB20XX Single Slot Cradles
No part of this publication may be reproduced or used in any form, or by any electrical or
mechanical means, without permission in writing from Zebra. This includes electronic or
mechanical means, such as photocopying, recording, or information storage and retrieval
systems. The material in this manual is subject to change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished
to the user is on a licensed basis. Zebra grants to the user a non-transferable and
non-exclusive license to use each software or firmware program delivered hereunder
(licensed program). Except as noted below, such license may not be assigned, sub-licensed,
or otherwise transferred by the user without prior written consent of Zebra. No right to copy a
licensed program in whole or in part is granted, except as permitted under copyright law. The
user shall not modify, merge, or incorporate any form or portion of a licensed program with
other program material, create a derivative work from a licensed program, or use a licensed
program in a network without written permission from Zebra. The user agrees to maintain
Zebra’s copyright notice on the licensed programs delivered hereunder, and to include the
same on any authorized copies it makes, in whole or in part. The user agrees not to
decompile, disassemble, decode, or reverse engineer any licensed program delivered to the
user or any portion thereof.
Zebra reserves the right to make changes to any software or product to improve reliability,
function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any
Zebra intellectual property rights. An implied license only exists for equipment, circuits, and
subsystems contained in Zebra products.
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many
jurisdictions worldwide. All other trademarks are the property of their respective owners.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Quick Reference Guide 3
Introduction
The STB20XX cordless scanner cradles act as chargers and host communication
interfaces for the MT2000 Series cordless scanners. Cradles can sit on a desktop,
mount on a wall or mount on a forklift (STB2000-F only). This document provides
basic instructions for cradle set up and use. Unless otherwise noted, “cradle”
refers to all configurations of the single slot cradle. Any discussion of transmission
of information refers specifically to cradles with Bluetooth technology.
Configurations
Cradle Configuration
STB2000 Single slot, charge only.
STB2078 Single slot, multi-interface with Bluetooth technology.
STB2000-F Forklift single slot, charge only.
Charge only cradles can communicate with a PC via
ActiveSync by attaching a USB cable to the USB connector
(see
Connections on page 7).
Note:
The USB port is used for service and maintenance
only.
Bluetooth
Bluetooth radio and send the data to the host through an
attached cable (see Connections on page 7).
cradles receive data from the scanner via a
Description
Accessories
The following equipment may be needed:
For the STB2000/STB2078 cradle:
• Power supply for desk/wall mounting configuration. See Power Supply on
page 18 for details.
• If applicable, three screws, depending on the surface, for wall mounting (not
available from Zebra).
For the STB2000-F cradle:
• Mounting bracket (provided).
• Power supply for forklift configuration. See Power Supply on page 18 for details.
• Three 8-32 x 1.25 in. screws to fasten the cradle to the bracket (provided).
• Four screws to fasten bracket to mounting surface (not available from Zebra).
4 STB20XX Single Slot Cradles
Related Documentation
• MT2070/MT2090 Quick Start Guide (p/n 72-117308-xx)
• MT2070/ MT2090 User Guide (p/n 72E-117859-xx)
• MT2070/ MT2090 Integrator Guide (72E-117858-xx)
• Enterprise Mobility Developer Kit (EMDK) Help File.
Documentation is available at: http://www.zebra.com/support.
Unpacking
Carefully remove all protective material from around the cradle and save the
shipping container for storing or shipping. Inspect all equipment for damage. If
anything is damaged or missing, call an authorized
immediately. See Service Information on backcover for contact information.
Verify that you received all equipment listed below:
• STB2000/STB2078:
• Cradle (desk mount cup installed)
• Wall mount cup.
• STB2000-F:
• Cradle
• Mounting bracket
• Three 8-32 x 1.25 in screws to fasten the cradle to the bracket
Zebra solutions Support Center
.
Quick Reference Guide 5
Rubber
Feet
Forklift
Bracket
Screw
Hole
1
Forklift
Bracket
Screw
Hole
1
Forklift
Bracket
Screw
Hole
1
Rubber
Foot
Rubber
Foot
Power
Cable
Groove
Cable
Hook
Power
Port
Host/USB
Port
Host/USB
Cable
Groove
Wall Mount
Conversion
Dial
Back
WARNING! Never connect an Ethernet or phone cable to the host interface port.
Front
Pairing Bar
Code
(STB2078
only)
LED
Latches
Charge/Communication
Contacts
Desk Cup
(Horizontal
Mount)
Cup
Release
Snaps
Mounting
Keyhole
2
Mounting
Keyhole
2
1
Used to fasten bracket to STB2000-F (forklift)
cradle.
2
Used to mount STB20XX cradle.
Features
6 STB20XX Single Slot Cradles
Cable
Access
Hole
Cable
Tie
Holes
Isolator
Cable
Tie
Holes
Cable
Tie
Holes
Isolator
Isolator
Mounting
Bracket
Forklift Mounting
Holes
Forklift
Mounting
Holes
Mounting Bracket (STB2000-F only)
The mounting bracket is used to install the cradle on a forklift. Mount the bracket so that
the cradle is within the user’s reach envelope. The recommended reach envelope has a
radius of 15 in. measured from the front of the user’s shoulder to the scanner grip.
Three isolators ensure secure attachment with minimized vibration. The bracket has
holes that provide access the host and power ports, and enable securing the cables
with cable ties.
CAUTION Ensure the Wall Mount Conversion Dial on the back of the cradle is in the
correct position for vertical mounting. If not, rotate the dial counterclockwise to activate
latches.
CAUTION Not for use in hazardous locations.
Quick Reference Guide 7
USB/Host Port
Power Port
Connections
IMPORTANT
CAUTION Routing of wiring: All wiring must be protected from strain and routed away
Connections vary by cradle configuration. The STB2000 and STB2000-F cradles
are charge only cradles. The host interface port can only be used to connect a
USB cable to a PC for an ActiveSync connection.
NOTE The host port is a maintenance port for the scanner, and can only be used for
Connect the USB/host interface cable and power supply (if necessary)
in the order of the steps below to ensure proper operation of the scanner
and cradle.
from heat sources and moving parts. The cable must be suitably rated for
exposure to water, oil and grease. All wiring should be appropriately
sleeved to protect it from exposure to water, oil and grease when mounted
on a fork lift.
an ActiveSync connection.
1. Insert the USB or host interface cable into the cradle’s USB/host port.
2. Connect the other end of the cable to the PC.
3. Connect the appropriate cable to the power supply and an AC power source, if
necessary.
4. Optional: Insert the power supply cable ferrite into the support features on the
cradle bottom and run the host and power cables into their respective cable
grooves.
For forklift cradles, if cables are not thread into their respective cable grooves,
it is recommended to use cable ties to secure cables to the mounting plate
after it is attached to the cradle (see Mounting the STB2000-F on the Forklift).
5. If necessary, scan the appropriate host bar code (for non-autodetected
interfaces).
6. For Bluetooth cradles, scan the Pairing bar code on the cradle. Refer to the
User Guide.
8 STB20XX Single Slot Cradles
Changing the Host Interface
To connect to a different host, or to the same host through a different cable:
1. Unplug the power supply from the cradle.
2. Unplug the interface cable from the host.
3. Connect the interface cable to the new host, or the new interface cable to the
existing host.
4. Reconnect the power supply, if required.
5. If necessary, scan the appropriate host bar code (for non-autodetected
interfaces). Refer to the User Guide.
CAUTION
If the scanner does not recognize the host, disconnect the power
supply, then reconnect after connecting the host cable.
Mounting the Cradle
Horizontal Mount
1. The cradle is packaged with the horizontal mount desk cup installed (see
Features on page 5). If it was replaced with the wall cup, remove the wall cup
and reattach the desk cup.
2. Use a Phillips screwdriver to turn the Wall Mount Conversion Dial to the correct
position for a desktop/horizontal mount (see Features on page 5).
3. Attach the appropriate cables.
4. Place the cradle on the desk to and insert the scanner.
Loading...