OPEN
LOCK
Contents of the Box
features and variants
expansion BaCk Cover
Camera
Blanking Plate
Expansion Back Cover with
Scanner/Imager Pod
Battery Compartment getting started
miCrosd and sim Card sLots
1
To insert a microSD or SIM card:
> Press the battery release buttons to remove the battery.
> Use a Phillips screwdriver to remove the SD cover screw.
> Flip the cover open.
Insert the Battery
Omnii This Guide Additional Documentation
features
front, right and Left
LEDs
Speaker
Beeper
Volume
Rocker Button
Vertical
Scroll
Button
Scan Button
ENTER
Button
Battery Release Button
Microphone
(dependent on order)
PTT Speaker
Version without Scanner
Note: GPS radio and end-cap, PTT speaker, and camera are all options
available with the Expansion Back Cover.
Version with Scanner
standard BaCk Cover
Standard Back Covers can support a variety of scanners and imagers.
Standard Back Cover
Version with pistol grip
Note: For all variants of both back covers, a pistol grip is available.
SD Cover
LOCK
microSD
Card Slot
SIM Card Slot
microSD card
2
Snap the Battery into Place
> Slide the microSD door to the left to
unlock it. Flip it open.
> Slide the microSD card onto the
Press down firmly on both sides of the battery to ensure that it
is securely seated in Omnii.
guides on the SD card door.
> Close the microSD door, and slide it
to the right to lock it.
SIM card
> Slide the SIM card metal door latch
to the right to unlock it. Flip it open.
OPEN
> Slide the SIM card into the guides on
the SIM card door.
> Close the SIM card door, and slide the
metal door latch to the left to lock it.
over
>
Charge the Battery
Turn the Unit On
43
resetting the unit
The power adaptor can be
plugged into a snap module
attached to Omnii.
The power adaptor can also
be plugged into the desktop
docking station.
Note: Use only the universal AC
power adaptor and
IEC320-C13 power cord
approved by Psion for
Omnii.
Allow the battery to charge for 3-4 hours.
Note: Full battery performance is only reached after the first
few full charge/discharge cycles.
Snap Module
0 – 40˚ C
32 – 104˚ F
Press and hold down the ENTER/
Power key for at least one second.
ENTER/Power Key
Connect Omnii to the PC
5
Connect through a docking station or a snap module
with a USB port.
Install and Configure Data Transfer Software
6
Use ActiveSync® (Windows® XP® or earlier) or Mobile Device Center® (Windows Vista
between Omnii and the PC and synchronize your e-mail, contacts,
and so on.
For either ActiveSync or Mobile Device Center, go to the following
website:
http://go.microsoft.com/fwlink/?LinkId=147001
To Turn Omnii Off, Do One of the Following:
7
> Press the FN key followed by the ENTER/Power key, or
> In the Start menu, choose Shutdown>Suspend.
®
or Windows 7®) to establish a connection
Important: Resetting may result in data loss.
To perform a cold reset:
> Press the SYM key, the FN key, and the ENTER/Power key
simultaneously for six seconds.
During a cold reset, running programs are halted and RAM memory is
cleared. The contents of flash memory and the registry are preserved.
The operating system is reloaded.
To perform a warm reset:
> Press the FN key and the ENTER/Power key simultaneously
for a few seconds.
During a warm reset, running programs are halted. The contents of
RAM, flash memory, and the registry are preserved.
© Copyright 2011 by Psion Inc.
Psion, Psion Teklogix, and Omnii are trademarks of Psion Inc. Other product names
mentioned in this document are trademarks or registered trademarks of other hardware,
software, or service providers and are used herein for identification purposes only.
hand-heLd
Computer
QuiCk start
guide
April 7, 2011
PN 8000223.A
ISO 9001 Certified
Quality Management System
Loading...