Zebra 7545MBW Quick Start Manuals

Download

Page 1

Version with scanner

Version with pistol grip

Version without scanner

OPEN

LOCK

OPEN

LOCK

CONTENTS OF THE BOX

FEATURES

FRONT, RIGHT AND LEFT

Omnii This guide Additional documentation

(dependent on order)

LEDs

Speaker

Volume rocker button

Scan button

Microphone

Beeper

Battery release button

Vertical scroll button

ENTER button

EXPANSION BACK COVER

BATTERY COMPARTMENT GETTING STARTED

FEATURES AND VARIANTS

MICROSD AND SIM CARD SLOTS

Camera

PTT speaker

Blanking plate

Standard back cover

Expansion back cover with scanner/imager Pod

STANDARD BACK COVER

Note: For all variants of both back covers, a pistol grip is available.

Note: GPS radio and end-cap, PTT speaker, and camera are all options

available with the Expansion Back Cover.

Standard Back Covers can support a variety of scanners and imagers.

To insert a microSD or SIM card:

> Press the battery release buttons to remove the battery. > Use a Phillips screwdriver to remove the SD cover screw. > Flip the cover open.

microSD card

> Slide the microSD door to the left to

unlock it. Flip it open.

> Slide the microSD card onto the

guides on the SD card door.

> Close the microSD door, and slide it

to the right to lock it.

SIM card

> Slide the SIM card metal door latch

to the right to unlock it. Flip it open.

> Slide the SIM card into the guides on

the SIM card door.

> Close the SIM card door, and slide the

metal door latch to the left to lock it.

SIM card slot

microSD card slot

SD cover

Insert the Battery

Snap the Battery into Place

Press down ﬁrmly on both sides of the battery to ensure that it is securely seated in Omnii.

OVER

For Narrowband Radio

Attach the antenna, following the instructions on the package, before inserting the battery.

Page 2

March 8, 2015 PN 8000223-002.A

RESETTING THE UNIT

To perform a warm reset:

> Press the FN key and the ENTER/Power key simultaneously

for a few seconds.

During a warm reset, running programs are halted. The contents of RAM, ﬂash memory, and the registry are preserved.

Charge the Battery

The power adaptor can be plugged into a snap module attached to Omnii.

The power adaptor can also be plugged into the desktop docking station.

Allow the battery to charge for 3-4 hours.

Note: Use only the universal AC

power adaptor and IEC320-C13 power cord approved by Psion for Omnii.

Note: Full battery performance is only reached after the ﬁrst

few full charge/discharge cycles.

Snap module

Connect Omnii to the PC

Connect through a docking station or a snap module with a USB port.

Install and Conﬁgure Data Transfer Software

Use ActiveSync® (Windows® XP® or earlier) or Mobile Device Center® (Windows Vista® or Windows 7®) to establish a connection between Omnii and the PC and synchronize your e-mail, contacts, and so on. For either ActiveSync or Mobile Device Center, go to the Microsoft Download Center:

http://www.microsoft.com/en-us/download/default.aspx

To Turn Omnii Off, Do One of the Following:

> Press the FN key followed by the ENTER/Power key, or > In the Start menu, choose Shutdown>Suspend.

0 – 40˚ C 32 – 104˚ F

IMPORTANT: Resetting may result in data loss.

Turn the Unit On

Press and hold down the ENTER Power key for at least one second.

To perform a cold reset:

> Press the SYM key, the FN key, and the ENTER/Power key

simultaneously for six seconds.

Running programs are halted and RAM memory is cleared. The contents of ﬂash memory and the registry are preserved. The operating system is reloaded.

OMNII HAND-HELD COMPUTER

Quick Start Guide

8 0 0 0 2 2 3 - 0 0 2

Zebra reserves the right to make changes to any product to improve reliability, function, or design.

Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuit, and subsystems contained in Zebra Products.

Warranty

For the complete Zebra hardware product warranty statement, go to: http://www.zebra.com/warranty

Zebra Technologies Corporation Lincolnshire, IL, U.S.A. http://www.zebra.com

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company.

This guide covers the following models:

- 7545MBW

- 7545MBWP

- 7545MBWPT

- 7545MBWT

- 7545MBWN