Please read these user instructions carefully and keep them to refer to later.
Please pass the user instructions on to any future owner of the appliance.
The following symbols are used in the text:
1 Safety instructions
Warning! Notes that concern your personal safety.
Important! Notes that show how to avoid damage to the appliance.
3 Please comply with these instructions. If you do not, any damage resulting
is not covered by the warranty.
5 This appliance conforms with the following EU Directives:
– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Di-
rective 92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Correct use
• This appliance should be used only for normal domestic cooking and frying of food.
• The appliance must not be used as a work surface or as a storage surface.
• Additions or modifications to the appliance are not permitted.
• Do not place or store flammable liquids, highly inflammable materials or
fusible objects (e.g. plastic film, plastic, aluminium) on or near the appliance.
Child safety
• Small children must be kept away from the appliance.
• Only let bigger children work on the appliance under supervision.
General safety
• The appliance may only be installed and connected by trained, registered
service engineers, or competent persons.
• Built-in appliances may only be used after they have been built in to suitable built-in units and work surfaces that meet standards.
• In the event of faults with the appliance or damage to the glass ceramic
(cracks, scratches or splits), the appliance must be switched off and disconnected from the electrical supply to prevent the possibility of an electric shock.
• Repairs to the appliance must only be carried out by trained registered
service engineers.
4
Safety during use
• Remove stickers and film from the glass ceramic.
• There is the risk of burns from the appliance if used carelessly.
• Cables from electrical appliances must not touch the hot surface of the
appliance or hot cookware.
• Overheated fat and oil can ignite quickly. When cooking with fat or oil (e.g.
frying chips) do not leave the appliance unattended.
• Switch the cooking zones off after each use.
Safety when cleaning
• For cleaning, the appliance must be switched off and cooled down.
• For safety reasons, the cleaning of the appliance with steam jet or high-
pressure cleaning equipment is not permitted.
How to avoid damage to the appliance
• The ceramic glass can be damaged by objects falling onto it.
• The edge of the ceramic glass can be damaged by being knocked by the
cookware.
• Cookware made of cast iron, cast aluminium or with damaged bottoms
can scratch the ceramic glass if pushed across the surface.
• Objects that melt and things that boil over can burn onto the ceramic
glass and should be removed straightaway.
• To avoid damaging cookware and glass ceramics, do not allow saucepans
or frying pans to boil dry.
• Do not use the cooking zones with empty cookware or without cookware.
5
Description of the Appliance
Cooking surface layout
Single cooking zone
1200W
Single cooking zone
1800W
Single cooking zone
1800W
Control panel layout
Cooking zones and heat setting selection
6
Control panel
Single cooking zone
1200W
Display
On/Off
Touch Control sensor fields
The appliance is operated using the Touch Control sensor fields. Functions
are controlled by touching sensor fields and confirmed by displays.
Touch the sensor fields from above, without covering other sensor fields.
Sensor fieldFunction
On / OffSwitches appliance on and off
Increase settingsSelect cooking zone
Increases heat setting
Reduce settingsReduces heat setting
Displays
Display Description
Cooking zone is switched off
- Heat settingsHeat setting is set
ERFaultMalfunction has occurred
Residual heatCooking zone is still hot
Child safety deviceLock/child safety device is set.
Residual heat indicator
1 Warning! Risk of burns from residual heat. After being switched off, the
cooking zones need some time to cool down. Look at the residual heat indicator
.
3 Residual heat can be used for melting and keeping food warm.
7
Operating the appliance
Switching the appliance on and off
Control panel Display
Switch onTouch for 2 seconds. / Decimal point flashes
Switch offTouch for 1 second
/ none
Selecting the cooking zone
Control panel Display
SelectTouch Decimal point illuminates
3 The decimal point is displayed by the selected cooking zone. Then a heat
setting must be set for this cooking zone within 6 seconds, otherwise it
must be re-selected.
Selecting the heat setting
3 After selecting the cooking zone, briefly release the sensor field .
Control panelDisplay
IncreaseTouch to
DecreaseTouch to
Switch offTouch and at the same time
3 After 6 seconds with no input the selection is cancelled and the decimal
point goes out. To set the required cooking zone again, make another selection.
8
Using the child safety device
The child safety device prevents unintentional use of the appliance.
3 The child safety device can only be activated immediately after the appli-
ance has been switched on.
Switching on the child safety device
Step Control panel Display
1.
2.Touch for 5 seconds is displayed.
Appliance switches off.
Switch on appliance.
(Do not set a heat setting.)
/ (if hot)
3 To override or switch the child safety device off sucessfully, the steps must
be performed immediately one after the other. No other sensor fields must
be touched between the steps described.
Overriding the child safety device
The child safety device can be switched off in this way for a single cooking
session; it remains activated afterwards.
StepControl panelDisplay
1. Switch appliance on / (if hot)
Touch the two
2.
Until the appliance is next switched off, it can used as normal.
cooking zones at the same time
of the front
Switching off the child safety device
or
Decimal points flash
StepControl panelDisplay
1.
2.
Appliance switches off.
Switch appliance on / (if hot)
Touch for 5 seconds or
Decimal points flash
9
Safety cut-out
Cooking surface
• If after switching on the appliance a heat setting is not set for a cooking
zone within approx. 10 seconds, the appliance automatically switches itself off.
• If one or more sensor fields are touched for longer than approx. 10 seconds, the cooking surface is automatically switched off. ER03 flashes on
the display or changes to if there is still residual heat.
• If all cooking zones are switched off, the cooking surface automatically
switches itself off after approx. 10 seconds.
Control panel
3 Moisture (e.g. a wet cloth) or liquid boiling over onto the control panel
switches all cooking zones off.
Cooking zones
• If one of the cooking zones is not switched off after a certain time, or if the
heat setting is not modified, the relevant cooking zone switches off automatically. is displayed.
Heat settingSwitches off after
1 - 26 hours
3 - 45 hours
54 hours
6 - 91.5 hours
10
Tips on cooking and frying
3 Information about acrylamides
According to the latest scientific research, intensive browning of food, especially in products containing starch, may present a health risk due to acrylamide. Therefore we recommend cooking at low temperatures and not
browning foods too much.
Cookware
• You can recognise good cookware from the bottoms of the pans. The bottom should be as thick and flat as possible.
• Cookware made of enamelled steel or with aluminium or copper bottoms
can leave discolourations on the ceramic glass surface which are difficult
or impossible to remove.
Energy saving
2Always place cookware on the cooking
zone before it is switched on.
2If possible, always place lids on the pans.
2Switch cooking zones off before the end
of the cooking time, to take advantage of
residual heat.
2Bottom of pans and cooking zones
should be the same size.
11
Examples of cooking applications
The information given in the following table is for guidance only.
Heat
setting
0
1
1-2
2-3
3-4
Cook-
ing
process
Keep-
ing food
warm
Melting
Solidify-
ing
Simmer-
ing
Steam-
ing
Braising
suitable for
Residual heat setting,
Off position
Keeping cooked foods
warm
Hollandaise sauce,
melting butter,
chocolate, gelatine
Fluffy omelettes,
baked eggs
Simmering rice and
milk-based dishes
Heating up ready-
cooked meals
Steaming vegetables,
fish
Braising meat
Cook
time
as re-
quired
5-25 mins.Stir occasionally
10-40
mins.
25-50
mins.
20-45
mins.
Tips/Hints
Cover
Cook with lid on
Add at least twice
as much liquid as
rice, stir milk dish-
es part way through
cooking
With vegetables
add only a little liq-
uid (a few table-
spoons)
12
4-5Boiling
6-7
Gentle
frying
Steaming potatoes
Cooking larger quanti-
ties of food, stews and
soups
Frying escalope, veal
cordon bleu, cutlets,
rissoles, sausages, liv-
er, roux, eggs,
pancakes, doughnuts
20-60
mins.
60-150
mins.
as re-
quired
Use only a little
liquid, e. g.: max.
¼ l water for
750 g of potatoes
Up to 3 l liquid plus
ingredients
Turn ha l f w a y
through cooking
Heat
setting
7-8
9
Cook-
ing
process
Heavy
frying
Boiling
Searing
Deep
frying
suitable for
Cook
time
Tips/Hints
Hash browns, loin
steaks, steaks, Flädle
(pancakes for garnish-
5-15 mins.
per pan
Turn ha l f w a y
through cooking
ing soup)
Boiling large quantities of water, cooking pasta, searing
meat (goulash, pot roast), deep frying chips
13
Cleaning and care
1 Take care! Risk of burns from residual heat.
1 Important Sharp objects and abrasive cleaning materials will damage the
appliance. Clean with water and washing up liquid.
1 Important Residues from cleaning agents will damage the appliance. Re-
move residues with water and washing up liquid.
Cleaning the appliance after each use
1. Wipe the appliance with a damp cloth and a little washing up liquid.
2. Rub the appliance dry using a clean cloth.
Removing deposits
1. Place the scraper on the glass ceramic surface at an angle.
2. Remove residues by sliding the blade over the surface.
3. Wipe the appliance with a damp cloth and a little washing up liquid.
4. Rub the appliance dry using a clean cloth.
Remove
im-
Type of dirt
sugar, food containing sugaryes---
plastics, tin foilyes---
limescale and water rings---yes
fat splashes---yes
shiny metallic discolouration---yes
*Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops, su-
permarkets, the parts department of your local Service Force Centre or from www.shop.electrolux.co.uk
medi-
ately
when the appliance
has cooled down
using
a scraper*
cleaner for glass
ceramic or stain-
less steel*
3 Remove stubborn residues with a cleaner for glass ceramic or stainless
steel.
3 Scratches or dark stains on the glass ceramic that cannot be removed do
not however affect the functioning of the appliance.
14
What to do if …
ProblemPossible causeRemedy
The cooking zones are
not functioning.
The cooking zones
cannot be selected /
Appliance does not react to the control panel
input
The residual heat indicator is not displaying
anything
No cooking zone selected
More than 10 seconds
has passed since the
appliance was
switched on
The child safety device
is activated
The sensor fields are
partly covered by a
damp cloth or with liquid
Safety cut-out has
been triggered
The cooking zone was
only on for a short time
and is therefore not hot
Select cooking zone
within 10 seconds of
switching on (Decimal
point lights up)
Switch on the appliance again.
Select cooking zone
within 10 seconds of
switching on
Deactivate the child
safety device (See section “Child safety device”)
Remove the cloth or the
liquid
Switch on the appliance again
If the cooking zone is
supposed to be hot,
call your local Service
Force Centre.
Er03is displayed
Er21is displayed
Er25is displayed
(only for 10 seconds)
Several sensor fields
were touched at the
same time
Safety cut-out due to
overheating.
Appliance is incorrectly
connected
Only touch one sensor
field
Let the appliance cool
down.
Remove cookware.
Disconnect the appliance from the electrical
supply and have it connected properly
15
ProblemPossible causeRemedy
Er40 is displayedThe overvoltage protec-
tor has been activated
(for an incorrect connection see above Er25
or for overheating of the
electronic components
see Er21)
Separate the appliance
from the mains for a
few minutes (remove
the mains fuse).
Let the appliance cool
down.
3 In the event of any other fault codes that arise, disconnect the appliance
from the electrical supply for a few seconds (Take out the fuse from the
house’s wiring system). If the fault code is displayed again, please call your
local Service Force Centre and report the fault code.
If you are unable to remedy the problem by following the above suggestions, please contact your local Service Force Centre.
1 Warning! Repairs to the appliance are only to be carried out by qualified
service engineers. Considerable danger to the user may result from improper repairs.
3 If the appliance has been operated incorrectly, the visit from the service
technician or dealer may not take place free of charge, even during the warranty period.
16
Disposal
2Packaging material
The packaging materials are environmentally friendly and can be recycled.
The plastic components are identified by markings, e.g. >PE<, >PS<, etc.
Please dispose of the packaging materials in the appropriate container at
your local waste disposal facilities.
2Old appliance
The symbol
uct may not be treated as household waste. Instead it shall be handed over
to the applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
W on the product or on its packaging indicates that this prod-
17
Installation Instructions
Safety instructions
The laws, ordinances, directives and standards in force in the country of use
are to be followed (safety regulations, proper recycling in accordance with
the regulations, etc.)
Installation may only be carried out by a qualified electrician.
The minimum distances to other appliances and units are to be observed.
Anti-shock protection must be provided by the installation, for example
drawers may only be installed with a protective floor directly underneath the
appliance.
The cut surfaces of the worktop are to be protected against moisture using
a suitable sealant.
The sealant seals the appliance to the work top with no gap.
Avoid installing the appliance next to doors and under windows. Otherwise
hot cookware may be knocked off the rings when doors and windows are
opened.
1 WARNING!
Risk of injury from electrical current.
• The electrical mains terminal is live.
• Observe connection schematic.
• Observe electrical safety rules.
• Ensure anti-shock protection through correct installation by a qualified
electrician.
• The appliance must be connected to the electrical supply by a qualified
electrician.
1 IMPORTANT!
Risk of injury from electrical current.
Loose and inappropriate plug and socket connections can make the terminal overheat.
• Have the clamping joints correctly installed by a qualified electrician.
• Use strain relief clamp on cable.
• In the event of single-phase or two-phase connection, the appropriate
mains cable of type H05BB-F Tmax 90° (or higher) must be used.
• If this appliance’s mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90°; or higher). Please contact your local
Service Force Center for further advice.
18
A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm
Suitable isolation devices include line protecting cut-outs, fuses (screw type
fuses are to be removed from the holder), earth leakage trips and contactors.
Electrical Connection Diagram
For UK only: 230V...240V~
Sticking on the seal
• Clean the worktop in the area of the cut-out section.
• Stick the one-sided self-adhesive sealing tape supplied all the way round
the lower edge of the cooking surface along the outer edge of the glass
ceramic panel. Do not stretch it. The cut ends should lie in the middle of
one side. When you have cut it to length (add a few mm), press the two
ends flush up against one another.
19
Assembly
20
21
22
23
Warranty conditions
Standard guarantee conditions
We, Zanussi, undertake that if within 24 months of the date of the purchase
this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or
replace the same FREE OF CHARGE for labour, materials or carriage on
condition that:
• The appliance has been correctly installed and used only on the electricity
supply stated on the rating plate.
• The appliance has been used for normal domestic purposes only, and in
accordance with the manufacturer’s instructions.
• The appliance has not been serviced, maintained, repaired, taken apart or
tampered with by any person not authorised by us.
• All service work under this guarantee must be undertaken by a Service
Force Centre.
• Any appliance or defective part replaced shall become the Company’s
property.
• This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits
may be available outside these hours in which case a premium will be
charged.
Exclusions
This guarantee does not cover:
• Damage or calls resulting from transportation, improper use or neglect,
the replacement of any light bulbs or removable parts of glass or plastic.
• Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom.
• Appliances found to be in use within a commercial environment, plus
those which are subject to rental agreements.
• Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee
moves with you to your new home subject to the following qualifications:
• The guarantee starts from the date you first purchased your product.
• The guarantee is for the same period and to the same extent for labour
and parts as exists in the new country of use for this brand or range of
products.
• This guarantee relates to you and cannot be transferred to another user.
24
• Your new home is within the European Community (EC) or European Free
Trade Area.
• The product is installed and used in accordance with our instructions and
is only used domestically, i.e. a normal household.
• The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed
below, to give them details of your new home. They will then ensure that the
local Service Organisation is aware of your move and able to look after you
and your appliances.
If the event of your appliance requiring service, or if you wish to purchase
spare parts, please contact Service Force by telephoning:
0870 5 929 929
Your telephone call will be automatically routed to the Service Force Centre
covering your post code area.
For the address of your local Service Force Centre and further information
about Service Force, please visit the website at
www. serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details under the heading „What to do if...“
When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model and serial number of the appliance (found on the rating
plate)
5. The purchase date.
Please note that a valid purchase receipt
or guarantee documentation is required
for in-guarantee service calls.
Customer Care
For general enquiries concerning your Zanussi appliance, or for further information
on Zanussi products please contact our
Customer Care Department by letter or
telephone at the address below or visit
our website at www.zanussi.co.uk..
Customer Care Department
Major Appliances
Zanussi
Addington Way
Luton
Bedfordshire, LU4 9QQ
Tel: 08705 350350 (*)
For Customer Service in the Republic of
Ireland please contact us at the address
below:
AEG/ Electrolux Group (Ire) Ltd
Long Mile Road/ Dublin 12
Republic of Ireland
Tel: +353 (0) 1 4090751
Email: service.eid@electrolux.ie
(*) Calls may be recorded for training purposes
26
Rating Plate
ZANUSSI
ZKT 641F
PEE2019
949 592 267
230 V50 Hz
6,0 kW
27
822 930323-A-310306-01 Subject to change without notice
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in
more than 150 countries around the world.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.