It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance and the relevant
warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully
before installing or using the appliance.
●
Installation
●
This appliance is heavy. Care should be taken when
moving it.
●
It is dangerous to alter the specifications or attempt
to modify this product in any way.
●
All packing and transit bolts must be removed before
use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant section
in instructions.
●
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
●
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
●
Care must be taken to ensure that the appliance does
not stand on the electrical supply cable.
●
If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely.
Child Safety
●
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
●
Pets and children have been known to climb into
washing machines. Please check your drum before
use.
●
The glass door becomes very hot during the washing
cycle. Keep children away from the vicinity of the
appliance whilst it is in operation.
Keep all packaging well away from children.
●
Keep all detergents in a safe place out of children’s
●
reach.
Use
●
Always unplug the appliance and turn off the water
supply after use.
Do not overload the appliance. See relevant section
in the instruction book.
●
Only wash fabrics which are designed to be machine
washed. If in doubt, consult the care label on the
clothes.
●
Before washing, ensure that all pockets are empty
and buttons and zips are fastened. Avoid washing
frayed or torn articles and treat stains such as paint,
ink, rust, and grass before washing. Under wired
bras must NOT be machine washed.
●
Any objects such as coins, safety pins, nails, screws,
stones or any other hard, sharp material can cause
extensive damage and must not be placed into the
machine.
●
Garments which have been in contact with volatile
petroleum products should not be machine washed.
If volatile cleaning fluids are used, care should be
taken to ensure that the fluid is removed from the
garment before placing in the machine.
●
Wash small items such as socks, laces, washable
belts etc in a washing bag or pillow case as it is
possible for such items to slip down between the tub
and the inner drum.
●
Only use the advised quantities of fabric softener.
Damage to the fabric can ensue if you over-fill.
Refer to the manufacturer’s recommendations of
quantities.
●
As some duvets and eiderdowns should be washed
in large commercial machines because of their bulk,
please check with the manufacturer of the item
before washing in a domestic machine.
●
Leave the porthole door slightly ajar between washes
to preserve the door seal.
●
Under no circumstances should you attempt to repair
the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Zanussi Service
Force Centre. Always insist on genuine Zanussi
spare parts.
2
Contents
For the User
Important Safety Information
Your New Washing Machine
Description of the Appliance
Detergent dispenser drawer5
Child safety feature5
The Control Panel
Programme information
Operating sequence
Load the laundry11
Measure out the detergent and the fabric softener11
Switch the machine on11
Select the required programme11
Select the Spin speed or the RINSE HOLD option11
Select the required options12
Select the DELAY START12
Start the programme12
At the end of the programme12
Washing Hints
Which detergent?....14
And in which form?14
Wash Care Symbols
Washing Programmes
6-10
10
11-12
13-14
15
16-17
19
Maintenance and Cleaning
Descaling18
2
After each wash18
Maintenance Wash18
4
External cleaning18
5
Cleaning the dispenser drawer18
Cleaning the drawer recess18
Cleaning the filter18-19
The dangers of freezing19
Emergency emptying out19
Something Not Working
Service and Spare Parts
Guarantee conditions
Unpacking24
Positioning24
Water inlet24-25
Water drainage25-26
Levelling26
Special conditions26
In the interest of the environment26
Electrical connection27
Building-in28-29
18-19
20-21
21-22
22
23
23
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
3
Your New Washing Machine
Your new washing machine fitted with the Zanussi “JET SYSTEM”, meets all modern
requirements for effective treatment of laundry with low water, energy and detergent
consumption.
Even small loads are washed “economically” because the amount of water used is regulated
automatically according to the load and type of fabric.
●
Automatic cooling of the wash water to 60°C
before draining, with the 95°C programme. This
reduces thermal shock to fabrics, helping to prevent
creasing.
●
The special wool programme with its new delicate
wash system treats your woollens with extreme care.
●
The balance control device ensures that the
washing machine remains stable when spinning.
Ecological hints
To save water and energy and help protect the
environment, we recommend that you follow these
hints:
●
Adjust the quantity of detergent according to the
hardness of your water supply, the amount of
laundry and the degree of soiling.
●
Select an “economy” programme for lightly soiled
laundry .
●
A programme without prewash is sufficient for
normally soiled laundry.
●
The machine works more economically if it is fully
loaded.
●
With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
In the interest of the
environment
●
Materials marked with the symbol are
recyclable.
●
Check with your local Council or Environmental
Health Office to see if there are facilities in your area
for re-cycling this appliance.
●
When the appliance is to be scrapped, cut off the
power supply cable and make the door lock device
unusable to prevent young children from being
trapped inside.
●
Help to keep your country tidy - use authorised
disposal sites for your old appliance.
The symbol on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste handling
of this product. For more detailed information about
recycling of this product, please contact your local
city office, your household waste disposal service or
the shop where you purchased the product.
How do we help to protect the environment?
We use recycled paper!
Important
Your machine is fitted with a balance control device, which ensures the machine is stable during the spin.
If the wash load appears not to have been spun sufficiently at the end of the wash cycle, it is because it is not evenly
distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the
wash load manually and select a spin programme. For more detailed information see the section headed "Something
Not Working".
4
Description of the Appliance
START
PAUSE
EASY
IRON
QUICK
WASH
DELAY
START
95º
E
60º
40º
30º
60º
40º
30º
40º
30º
X
40º
COTTON
DELICATES
SYNTHETICS
WOOL
60º
SPECIAL
40º
E
60º
E
SUPER
RINSE
SPIN
SPEED
PREWASH
DAILY
30º
1200
900
700
500
ZJ
.
1218
ON/OFF
Programme chart
P0239S
P1131
1 Detergent dispenser drawer
2 Programme guide
3 Control panel
4 Door opening handle
5 Filter
6 Adjustable feet
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
Child safety feature
This machine incorporates a special child safety feature
to prevent small children from being trapped inside the
machine.
To activate this device, rotate the button (without
pressing it) inside the door clockwise until the groove is
horizontal. If necessary use a coin.
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise until
the groove is vertical.
5
The Control Panel
1
2
3
4
59678 1011
12
1314
START
PAUSE
EASY
IRON
QUICK
WASH
DELAY
START
95º
E
60º
40º
30º
60º
40º
30º
40º
30º
X
40º
COTTON
DELICATES
SYNTHETICS
WOOL
60º
SPECIAL
40º
E
60º
E
SUPER
RINSE
SPIN
SPEED
PREWASH
DAILY
30º
1200
900
700
500
ZJ
.
1218
ON/OFF
1Detergent dispenser drawer
2 Mains-on light
This light comes on when the ON/OFF button is
pressed, and goes out when it is pressed again.
3 ON/OFF button
Press this button to switch the machine on. Press it
again to switch the machine off.
Programme Option buttons
Depending on the programme, different functions can
be combined. These must be selected after choosing the
desired programme and before depressing the START
PAUSE button.
When these buttons are pressed, the corresponding pilot
lights come on. When they are pressed again, the pilot
lights go out.
If an incorrect option is selected, the corresponding
pilot light flashes for about 2 seconds and the message
Err is displayed.
4 SPIN SPEED button
Rinse Hold
When RINSE HOLD option is selected, the last rinse
water is not emptied out, to prevent the fabrics from
creasing. When the programme has finished, the light
of the START PAUSE button and the pilot light
(DOOR) go out, the light and the pilot light
(
END) are alight to indicate that the water must be
emptied out.
There are two methods of draining the water from the
machine.
Method 1: Drain the water only, no spin:
• Turn selector dial to "X" position.
• Select the programme (draining).
The water will be emptied out without spinning.
Method 2: Drain and then spin the laundry:
• Turn selector dial to "X" position.
• Select programme (Spin) or (delicate spin).
• Select the required spin speed (see 4 Spin Speed
button)
• Press Start/Pause button
The water will empty out and then the laundry will be
spun at the selected spin speed.
Press this button to reduce the maximum speed of the
final speed proposed by the machine for the selected
programme or to select position (RINSE HOLD) .
The light corresponding to the
selected option illuminates.
The following speeds are available for the different
fabrics:
• C
• S
YNTHETICS and WOOL/(handwash):
500/700 max 900 r.p.m.
• D
, linen: 500/700/900 max 1200 r.p.m.
OTTON
ELICATES and MINI-PROGRAMME:
500 max 700 r.p.m.
Attention! Before selecting programmes (Drain),
(Spin) or (delicate spin), the selector dial has to
be positioned on X (cancelling).
5 PREWASH button
The machine performs a prewash cycle at 30°C max.
The prewash cycle ends with a short spin at 650 r.p.m.
in programmes for Cotton and Synthetics, and with
emptying of the water for Delicates.
This option is not available with the
programme and mini-program .
For use when washing heavily soiled laundry.
6
WOOL/(handwash)
6 DAILY button
This option can be used for lightly soiled cotton or
synthetic items in order to obtain a good washing
performance in a short time.
This option cannot be used with the Economy
programmes 60°E and E°40 and Mini-Programme
and also not in combination with QUICK WASH
option.
7 QUICK WASH button
This option can be used for lightly soiled cotton,
synthetic or delicate items that have been used or worn
for a short time.
This option is not available with the
(handwash) programme, the Energy saving
programmes (60°E and 40°E) and Mini-Programme .
It cannot be used also in combination with DAILY
option.
WOOL/
8 SUPER RINSE button
This option can be selected with all programmes, except
the
WOOL/ HANDWASHand Mini-Programme .
The machine will add 2 rinses for cotton and 1 rinse for
synthetics and delicates.
This option is recommended for people who are allergic
to detergents and in areas where the water is very soft.
9 EASY IRON button
Selecting this button the laundry is gently washed and
spun to avoid any creasing. In this way ironing is easier.
Furthermore the machine will perform 6 rinses instead
of 3 for cotton and 4 rinses instead of 3 for synthetics.
This function can be used only for cotton and synthetic
fabrics.
If this option is selected for cotton programmes, the spin
speed automaticaly will reduce to 900 rpm.
If this option is selected for synthetic programmes with
a temperature of 60°C or 50°C, the machine will perform
a washing cycle at max 40°C.
10 DELAY START button
The wash programme can be delayed from 30 min - 60
min - 90 min, 2 hours and then by 1 hour up to a
maximum of 23 hours by means of this button.
● Select the programme and the required options.
● Select the delay start.
● Depress START PAUSE button: the machine starts
its hourly countdown.
The programme will start after the selected delay has
expired. The DELAY START cannot be used with
(D
RAIN), (SPIN) or (DELICATE SPIN)
programmes.
Cancelling the delayed start
● Depress START PAUSE button.
● Depress DELAY START button until «0’» is
displayed.
● Depress START PAUSE button again, if you wish to
restart the machine immediately.
11 START/PAUSE button
This button has two functions: Start - Pause
Start
After having selected the required programme, press this
button to start the machine; the corresponding pilot light
stops flashing.
If you have selected the delayed start, the machine
begins its countdown. The duration of the programme or
the delay appears on the display.
Pause
To interrupt a programme which is running, depress the
START PAUSE button: the corresponding pilot light
starts to flash.
To restart the programme from the point at which it was
interrupted, press the START PAUSE button again.
12 DISPLAY
The display shows the following information:
Reset/Cancelling - Duration of the programme Delayed start - Incorrect option selection - Alarm
code - End of programme.
Reset/cancellation of the programme
If the programme selector dial is turned to X position,
three blinking dashes are displayed.
Now you can select a new programme.
(If the programme selector dial has not turned to X
position , when you press the ON/OFF button to switch
the machine on, the display will show a blinking zero.)
Selecting the delayed start
7
Duration of the selected programme
DELAY
START
2.05
---
0
E20
After selecting a programme, the duration is displayed
in hours and minutes ( for example 2.05).
The duration is calculated automatically on the basis of
the maximum recommended load for each type of
fabric.
After the programme has started, the time remaining is
updated every minute.
Delayed start
The selected delay (23 hours max) set by means of the
relevant button appears on the display for 3 seconds,
then the duration of the previously selected programme
is displayed.
The countdown is updated every hour and, when remain
the last 2 hours, each 30 min.
Alarm codes
In the event of operating problems, some alarm codes
can be displayed, for example E20 (see paragraph
“Something not working”).
End of programme
When the programme has finished a flashing zero is
displayed. The door can be opened when the
(D
OOR) pilot light has gone out and if the (RINSE
) option has not been selected.
HOLD
IInnccoorrrreeccttooppttiioonnsseelleeccttiioonn
If an option which is not compatible with the set wash
programme is selected, the message Err is displayed for
2 seconds.
13 Programme progress display
By selecting the wash programme, the pilot lights
corresponding to the various phases making up the
programme come on.
After the machine has started, the(D
light and only the running phase light illuminate and
stay on.
When the programme has finished, the (
light comes on and the the(D
pilot light goes off.
8
OOR) pilot
OOR)
END) pilot
95º
E
60º
40º
30º
60º
40º
30º
40º
30º
X
40º
COTTON
DELICATES
SYNTHETICS
WOOL
60º
SPECIAL
40º
E
60º
E
30º
WASH
CLOGGED
FILTER
DOOR
PREWASH
SPIN
END
RINSES
DRAIN
The selector dial can be turned either clockwise or
anticlockwise.
Position E corresponds to the ENERGY SAVING
programmes and position to “cold wash”.
At the end of the programme the selector dial must
be turned to position X (reset).
Functions
The(D
OOR) pilot light indicates if during the
washing cycle the door can be opened:
• Light on: the door can be opened
(when the washing machine is set to PAUSE, the
(D
OOR) pilot light will go off).
• Light off: the door cannot be opened
(when the washing machine is set to PAUSE, the
OOR) pilot light will start to flash)
(D
The (END) pilot light flashes in the event of
operating problems and the corresponding alarm code
appears on the display.
EE1100
= the machine does not fill
EE2200
= the machine does not empty
EE4400
= the door has not been closed
To eliminate the problem, see paragraph “Something not
working”.
If the (
FIL TER CLOGGED) pilot light flashes at the
end of the programme this means that the drain filter
must be cleaned.
14 Programme selector dial
The selector is divided into 5 sections:
• C
OTTON,
• S
YNTHETICS
• DELICA TES
• WOOL(hand washing)
• Special programmes
• Reset programme X
End of programme
When the (END) pilot light on the programme
progress display illuminates, if the
(D
OOR) pilot light has gone out, the the door can be
opened (if the (
RINSE HOLD) option has not been
selected).
Turn the programme selector dial to X.
Switch the machine off by depressing the ON/OFF
button before removing the laundry.
Altering an option or a running programme
It is possible to change any option before the
programme carries it out.
Before you make any change, you must pause the
washing machine by pressing the START PAUSE
button.
Changing a running programme is possible only by
resetting it. Turn the programme selector dial to "X" and
then to the new programme position. The washing water
in the tub will not emptied out .
Start the new programme by depressing the START
PAUSE button.
Interrupting a programme
Depress the START PAUSE button to interrupt a
programme which is running: the corresponding light
starts to flash.
Depress the same button to restart the programme.
9
Loading...
+ 21 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.