Zanussi ZGG754ICN, ZGG753ALU, ZGG754ITAC, ZGG753ICX, ZGG754ICX User Manual
ENGLISH
Important Safety Information
These warnings are provided in the interest of safety. You MUST read them carefully before
installing or using the appliance.
During Operation
This appliance has been designed for non professional
purpose in private houses only. It is meant to cook
edible foodstuff only and MUST NOT be used for any other
purposes.
It is dangerous to alter the specification in any way.
For hygiene and safety reasons, this appliance should
be kept clean at all times. A build-up of fats or other
foodstuff could result in a fire.
Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Zanussi Service
Centre. Always insist on genuine Zanussi spare parts.
Ensure that all control knobs are in the OFF position
when not in use.
Should you connect any electrical tool to a plug near
this cooking appliance, ensure that electric cables are
not in contact with it and keep them far enough from
the heated parts of this appliance.
If the appliance is out of order, disconnect it from the
electric supply.
Child Safety
This appliance has been designed to be operated by
adults and children under supervision. Young children
MUST NOT be allowed to tamper with the controls or play
near or with the oven.
Accessible parts of this appliance may become hot
when it is in use. Children should be KEPT AWAY until it
has cooled.
Ensure that the gas supply complies with the gas type
stated on the identification label, placed near the gas
supply pipe.
Using a gas cooking appliance will produce heat
and moisture in the room which it has been
installed in. Ensure a continuous air supply,
keeping the air vents in good conditions or
installing a cooker hood with discharge tube.
In case of intensive or long time use of the
appliance, make the ventilation more efficient,
by opening a window or increasing the electric
exhaust fan power.
Once you removed all packaging from the appliance,
ensure that it is not damaged and the electric cable is
in perfect conditions. Otherwise, contact your dealer
before proceeding with the installation.
The manufacturer disclaims any responsability
should all the safety measures not be carried out.
Service
Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
Environmental Information
After installation, please dispose of the packaging
with due regard to safety and the environment.
When disposing of an old appliance, make it
unusable, by cutting off the cable.
About Installation, Cleaning
and Manteinance
It is mandatory that all operations required for the
installation are carried out by a qualified or competent
person, in accordance with existing rules and
regulations.
Disconnect the appliance from the electrical supply,
before carrying out any cleaning or manteinance work.
Ensure a good ventilation around the appliance. A
poor air supply could cause lack of oxygen.
30
It is most important that this instruction
book should be retained with the appliance
for future reference. Should the appliance
be sold or transferred, always ensure that
the book is left with the appliance in order
that the new owner can get to know the
functions of the appliance and the relevant
warnings. These instructions are only for the
countries stated by the symbol printed on the
front cover of this instruction book.
Contents
For the User
Instruction for the User 31
Cleaning and Maintenance 30
Guarantee 40
Guide to Use the instructions
The following symbols will be found in the text to
guide you throughout the Instructions:
Safety Instructions
Step by step instructions for an
F
operation
Hints and Tips
i
Environmental information
For the Installer
Technical Data 33
Electrical Connection 34
Adaptation to different types of gas 35
Building In 36
MANUFACTURER:
ELECTROLUX ZANUSSI S.p.A.
Viale Bologna, 298
47100 FORLÌ (Italie)
This appliance complies with the
following E.E.C. Directives:
- 73/23 - 90/683 (Low Voltage Directive);
- 89/336
Directive);
- 93/68 (General Directives)
and subsequent modifications.
(Electromagnetical Compatibility
Instruction for the User
Hob burners control knobs
The hob burners control knobs are situated on the hob
right hand side. The symbols on the knobs mean that :
l there is no gas supply
there is maximum gas supply
there is minimum gas supply
Lighting the burners
For easier lighting, proceed before putting a
i
pan on the pan support.
To light a burner, turn the relevant knob anticlockwise
F
to maximum position and push down the knob to
ignite.
After lighting the flame, keep the knob pushed down
for about 5 seconds. This will allow the "thermocouple"
(Fig. 1 lett. C) to be heated and the safety device to
be switched off, otherwise the gas supply would be
interrupted. Then, check the flame is regular and
adjust it as required.
If you cannot light the flame even after several
attempts, check the "cap" (Fig. 1 lett. A) is in the
correct position.
To put the flame out, turn the knob to the symbol l.
Always turn the flame down or put it out before
taking the pans off the burner.
Fig. 1
Burner minimum maximum
Big (rapid) 180 mm. 260 mm.
Medium (semirapid) 120 mm. 220 mm.
Small (Auxiliary) 80 mm. 160 mm.
FO 2295
A - Burner cap
B - Ignition candle
C - Thermocouple
diameter diameter
31
Using the hob correctly
To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
bottom fitting the size of the burner used, so that flame will
not spread beyond the bottom of the vessel (see the table
beside).
It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.
Use only pans or pots with flat bottom.
Carefully supervise cookings with fats or oil, since
i
these types of foodstuff can result in a fire, if overheated.
Cleaning and Maintenance
Disconnect the appliance from the electrical
supply, before carrying out any cleaning or
manteinance work.
Wash the enamelled components with warm soapy
water. Never use abrasive cleaners.
Frequently wash the "caps" and the "crowns" with hot
soapy water, carefully taking away any built-up of food.
The pan supports are dishwasher proof.
If the marks are particularly difficult to remove, use
common non-abrasive cleaners or specific products.
Never use steel wool pads or acids.
Regularly wipe over the hob top and the aluminium frame
using a soft cloth weel wrung out in warm water to which
a little liquid detergent has been added. Avoid the use of
the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a proper cleaning product is used.
The electric ignition is obtained through a ceramic
"candle" and a metal electrode (fig. 1 lett. B). Keep these
components well clean, to avoid difficult lighting, and
check that the burner crown holes (lett. A) are not
obstructed.
The cap and the crown of each burner are secured with
two screws. To separate the two pieces, lift the cap, turn
it upside down, then undo the two fixing screws as
shown in Fig. 3.
After a thorough cleaning, reassemble the two parts and
refit the cap in its correct position on the burner.
Periodic maintenance
Periodically ask your local Service Centre to check the
conditions of the gas supply pipe and the pressure
adjuster, if fitted.
To ensure the good operation of the hob and its safety
features, it is necessary that the taps are periodically
lubricated.
Fig. 2
FO 2110
l The periodic lubrication of the taps must be
carried out by qualified personnel, which you
must refer to also in case of malfunctioning.
32
Fig. 3
FO 2265
Technical Data
Gas Burners Rating
Rapid Burner (big) 2,9 kW (G20/G25) - 2,7 kW (G30/G31)
Semirapid Burner (medium) 1,9 kW
Auxiliary Burner (small) 1 kW
Appliance Class : 3
Category II 2E+3+
Setting Natural Gas 20 mbar / G25 25 mbar
Gas connection G 1/2"
Electric Supply 230 V 50 Hz
HOB RECESS
DIMENSIONS
Length 560 mm.
Width 480 mm.
Instruction for the Installer
l The following instructions about installation and
maintenance must be carried out by qualified
personnel in compliance with the regulation in
force. The regulation to be applied for this type
of installation is NBN D 5I.003 : "Installations
functioning with combustible gas lighter than
air".
l The side walls of the unit in which the hob is
going to be installed, must not exceed the height
of the working top.
l Avoid installing the appliance in the proximity of
inflammable materials (e.g. curtains, tea towels
etc.).
l The appliance must be electrically disconnected
before all interventions. If any electric supply to
the appliance is required to carry out the work,
ensure all the necessary precautions are followed.
Gas connection
It is indispensible that the connection to the gas mains
are carried out by means of an AGB tap. Choose fixed
connections or use a flexible pipe in AGB (stainless
steel).
If using flexible metallic pipes, be careful they do not
come in contact with mobile parts or they are not
squeezed. Use the same attention when the hob is
combinated with an oven.
This hob can be operated by Slochteren gas (G25) with
a nominal pressure of 25 mbar or by natural gas with
nominal pressure of 20 mbar. No regulation is required for
use by these two types of gas.
Before fitting the appliance ensure that the installation
has the correct voltage for the appliance. At full capacity,
the drop in pressure must not exceed 5%. Such a drop in
pressure is caused by the following parameters:
- maximum capacity of meter;
- diameter and lenght of the tube in front and behind the
meter;
- section of transit of variuos tubes positioned on the
circuit;
- diameter of eventual connections.
FO 2365
A) Ramp with ending nut
B) Seal
C) Adjustable connection
Fig. 4
IMPORTANT - To ensure a correct operation, a saving
of energy and the long-life of the appliance, the voltage
pressure of the appliance must correspond to the
recommended values.
The adjustable connection is fixed to the comprehensive
ramp by means of a threaded nut GJ 1/2". Interpose the
sealing between the components as shown in fig. 4.
Screw the parts without forcing, adjust the connection in
the required direction and tighten everything.
IMPORTANT - When the final connection has been
made, it is essential that a thorough leak test is carried
out on the hob and installation. Use some soapy water,
never a flame.
33
Loading...