Zanussi ZGG753 USER MANUAL
TABLE DE CUISSON
KOOKPLATEAU
KOCHMULDE
BUILT-IN HOB
MODE D'EMPLOI - GEBRUIKSAANWIJZING
BEDIENUNGSANLEITUNG - OPERATING INSTRUCTIONS
BE
ENGLISH
Important Safety Information
These warnings are provided in the interest of safety. You MUST read them carefully before
installing or using the appliance.
During Operation
This appliance has been designed for non
professional purpose in private houses only. It is
meant to cook edible foodstuff only and MUST NOT be
used for any other purposes.
It is dangerous to alter the specification in any way.
For hygiene and safety reasons, this appliance
should be kept clean at all times. A build-up of fats
or other foodstuff could result in a fire.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Zanussi Service
Centre. Always insist on genuine Zanussi spare
parts.
Ensure that all control knobs are in the OFF position
when not in use.
Should you connect any electrical tool to a plug near
this cooking appliance, ensure that electric cables
are not in contact with it and keep them far enough
from the heated parts of this appliance.
If the appliance is out of order, disconnect it from the
electric supply.
Child Safety
This appliance has been designed to be operated by
adults and children under supervision. Young children
MUST NOT be allowed to tamper with the controls or
play near or with the oven.
Accessible parts of this appliance may become hot
when it is in use. Children should be KEPT AWAY until
it has cooled.
type stated on the identification label, placed near
the gas supply pipe.
Using a gas cooking appliance will produce
heat and moisture in the room which it has been
installed in. Ensure a continuous air supply,
keeping the air vents in good conditions or
installing a cooker hood with discharge tube.
In case of intensive or long time use of the
appliance, make the ventilation more efficient,
by opening a window or increasing the electric
exhaust fan power.
Once you removed all packaging from the appliance,
ensure that it is not damaged and the electric cable
is in perfect conditions. Otherwise, contact your
dealer before proceeding with the installation.
The manufacturer disclaims any responsability
should all the safety measures not be carried
out.
Service
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
Environmental Information
After installation, please dispose of the packaging
with due regard to safety and the environment.
When disposing of an old appliance, make it
unusable, by cutting off the cable.
About Installation, Cleaning
and Manteinance
It is mandatory that all operations required for the
installation are carried out by a qualified or competent
person, in accordance with existing rules and
regulations.
Disconnect the appliance from the electrical supply,
before carrying out any cleaning or manteinance
work.
Ensure a good ventilation around the appliance. A
poor air supply could cause lack of oxygen.
Ensure that the gas supply complies with the gas
30
It is most important that this instruction
book should be retained with the appliance
for future reference. Should the appliance
be sold or transferred, always ensure that
the book is left with the appliance in order
that the new owner can get to know the
functions of the appliance and the relevant
warnings. These instructions are only for the
countries stated by the symbol printed on the
front cover of this instruction book.
Contents
For the User
Instruction for the User 31
Cleaning and Maintenance 30
Guarantee 40
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
F
Hints and Tips
Environmental information
For the Installer
Technical Data 33
Electrical Connection 34
Adaptation to different types of gas 35
Building In 36
MANUFACTURER:
ELECTROLUX ZANUSSI S.p.A.
Viale Bologna, 298
47100 FORLÌ (Italie)
This appliance complies with the
following E.E.C. Directives:
- 73/23 - 90/683 (Low Voltage Directive);
- 89/336
Directive);
- 93/68 (General Directives)
and subsequent modifications.
(Electromagnetical Compatibility
Instruction for the User
Hob burners control knobs
The hob burners control knobs are situated on the hob
right hand side. The symbols on the knobs mean that :
l there is no gas supply
there is maximum gas supply
there is minimum gas supply
Lighting the burners
For easier lighting, proceed before putting a
pan on the pan support.
To light a burner, turn the relevant knob anticlockwise
to maximum position and push down the knob to
F
ignite.
After lighting the flame, keep the knob pushed
down for about 5 seconds. This will allow the
"thermocouple" (Fig. 1 lett. C) to be heated and the
safety device to be switched off, otherwise the gas
supply would be interrupted. Then, check the flame
is regular and adjust it as required.
If you cannot light the flame even after several
attempts, check the "cap" (Fig. 1 lett. A) is in the
correct position.
To put the flame out, turn the knob to the symbol l.
Always turn the flame down or put it out before
taking the pans off the burner.
Fig. 1
Burner minimum maximum
Big (rapid) 180 mm. 260 mm.
Medium (semirapid) 120 mm. 220 mm.
Small (Auxiliary) 80 mm. 160 mm.
FO 2295
A - Burner cap
B - Ignition candle
C - Thermocouple
diameter diameter
31
Using the hob correctly
To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
bottom fitting the size of the burner used, so that flame
will not spread beyond the bottom of the vessel (see the
table beside).
It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.
Use only pans or pots with flat bottom.
Carefully supervise cookings with fats or oil,
since these types of foodstuff can result in a fire,
if over-heated.
Cleaning and Maintenance
Disconnect the appliance from the electrical
supply, before carrying out any cleaning or
manteinance work.
Wash the enamelled components with warm soapy
water. Never use abrasive cleaners.
Frequently wash the "caps" and the "crowns" with hot
soapy water, carefully taking away any built-up of food.
The pan supports are dishwasher proof.
If the marks are particularly difficult to remove, use
common non-abrasive cleaners or specific products.
Never use steel wool pads or acids.
Regularly wipe over the hob top and the aluminium
frame using a soft cloth weel wrung out in warm water
to which a little liquid detergent has been added. Avoid
the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a proper cleaning product is used.
The electric ignition is obtained through a ceramic
"candle" and a metal electrode (fig. 1 lett. B). Keep
these components well clean, to avoid difficult lighting,
and check that the burner crown holes (lett. A) are not
obstructed.
The cap and the crown of each burner are secured with
two screws. To separate the two pieces, lift the cap,
turn it upside down, then undo the two fixing screws
as shown in Fig. 3.
After a thorough cleaning, reassemble the two parts
and refit the cap in its correct position on the burner.
Periodic maintenance
Periodically ask your local Service Centre to check the
conditions of the gas supply pipe and the pressure
adjuster, if fitted.
To ensure the good operation of the hob and its safety
features, it is necessary that the taps are periodically
lubricated.
Fig. 2
FO 2110
l The periodic lubrication of the taps must be
carried out by qualified personnel, which you
must refer to also in case of malfunctioning.
32
Fig. 3
FO 2265
Loading...