Zanussi ZFC 622 WA User Manual
USER MANUAL
EN
ZFC 622 WA
ZFC 626 WA
ZZAANNUUSSSSII
2
EN
EN
Disposal
By ensuring this product is disposed of correctly, you will help prevent potential damaging consequences for the environment and human health.
The symbol on the product indicates that this product may not be treated as household waste. Instead it should be
taken to an appropriate collection point for the recycling of electrical and electronic equipment. For more detailed
information about recycling of this product, please contact your local council, your household waste disposal service or
the shop where you purchased the appliance.
Safety Information
Before installing and using the appliance read this user's instruction book carefully. It contains safety precautions, hints,
information and ideas. If the freezer is used in compliance with these instructions, it will operate properly and provide
you with the greatest satisfaction.
These warnings are provided in the interest of safety. You must read them carefully before installing or using the appliance.
Use the freezer only for storing frozen food, freezing fresh food and making ice cubes.
Do not eat ice cubes or ice lollies immediately after taking them out of the freezer, as they may cause frost burns.
Do not allow children to play or hide inside the freezer, as they may become trapped inside and suffocate.
Do not store glass containing liquids in the freezer, as they may burst.
Ensure that the freezer is not resting on the power supply cable.
Before servicing or cleaning, always unplug the appliance or disconnect from the power supply.
Do not use other electrical appliances (such as ice cream makers) inside the appliance.
Your appliance contains an environmentally friendly natural gas, isobuthane (R600a). Caution is required however, as
isobuthane is flammable. Therefore it is essential to ensure that the refrigerant pipelines are not damaged.
It is most important that this instruction book should be retained with the appliance for future reference.
Product Description
Installation
Wait at least 2 hours before connecting the freezer to the power supply to ensure the refrigerant circuit is fully efficient.
Install the freezer in a dry, well ventilated room. Avoid locations near a source of heat or in direct sunlight.
The room temperature should correspond to the climatic classification for which the freezer was designed, see chapter "Technical data".
Place the freezer horizontally on a firm surface, resting on all four feet.
For optimum operation and in order to avoid damage when the lid is opened, leave a space of at least 5 cm from the
rear wall and 5 cm at the sides.
Before connecting the freezer to the power supply, ensure that the voltage corresponds to that indicated in chapter
"Technical data" under "Voltage".
Danger!
Ensure that the freezer is not resting on the power supply cable.
Do not remove the power supply cable by pulling on its lead, particularly when the freezer is being pulled out of its
niche.
The power supply cable may only be replaced by qualified electrician.
Ensure that the power plug is not squashed or damaged by the back of the freezer.
There must be adequate ventilation around the appliance.
Any electrical work required to install this appliance should be carried out by a qualified electrician.
1. Lid handle
2. Seal
3. Defrost water drain
4. Thermostat knob: temperature adjustment
5. Upper edge
6. Light
7. Valve: easy re-opening of lid
7
5
4
3
6
2
3
EN
EN
Electrical connection
The appliance is supplied with a 13amp plug fitted. In the event of having to change the
fuse in the plug supplied, a 13amp ASTA approved (BS1362) fuse must be used. Should
the plug need to be replaced for any reason. The wires in the power supply cable are
coloured in accordance with the following code:
Green and Yellow - Earth: must be connected to the terminal marked with the letter "E"
or by the earth symbol or coloured green and yellow.
Blue - Neutral: must be connected to the terminal "N" or coloured black.
Brown - Live: must be connected to the terminal marked "L" or coloured red.
Upon completion there must be no cut, or stray strands of wire present and the cord
clamp must be secure over the outer sheath.
Warning! This appliance must be earthed.
First use
Before first use, the freezer should be cleaned inside, see chapter “Care and cleaning”.
Plug in the appliance and allow the freezer to run for several hours before placing food inside.
Switch on-off
Switch on the freezer
Turn the thermostat knob to a postion between and .
Switch off the freezer
Turn the thermostat knob to the Off position.
Daily use
Temperature adjustment
To adjust the temperature of the freezer, proceed as follows:
Turn the thermostat knob clockwise towards for a colder storage temperature.
Turn the thermotat knob counter-clockwise towards for a less cold storage temperature.
Storage baskets
Hang the baskets on the upper edge (X) or place the stackable baskets inside the freez-
er (Y).
Turn and fix the handles for these two positions, as shown in the drawings.
Spare baskets can be obtained from your local Service Force
Centre or from the Electrolux website (depending on country).
The illustrations on this page show how many baskets can be
placed in the various freezer models.
Opening and closing the lid
As the lid is fitted with a tightly closing seal, it will not re-open easily immediatedly after closing.
Wait a few minutes before re-opening the lid. The vacuum release will allow the lid to be re-opened easily. Never pull
the handle with immense force.
Care and Cleaning
Defrosting the freezer
When the ice layer is 10-15 mm thick, the freezer should be defrosted. We suggest that you defrost your freezer when
there is little or no food inside.
Disconnect the appliance from the power supply.
Remove the contents of the freezer, wrap them in newspapers, and keep them in a cold place.
Leave the appliance lid open.
Remove the plug from the water drain.
The defrost water can be collected in a tray as shown in the drawing. If available, use the divider.
Speed up defrosting by using the enclosed scraper to detach the ice from the appliance walls.
Dry the interior of the appliance thoroughly.
Remember to replace the plug in the water drain.
Important! Never use a knife or any other sharp implement to remove frost or ice.
Loading...