POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
AVERAGE DAILY UNITS ELECTRICITY*
GROSS CAPACITY
Fridge
Freezer
NET CAPACITY
Fridge
Freezer
STAR RATING
* This figure is based on standard test results in accordance with European Standard EN153. Actual
consumption will depend on how the appliance is used and where it is located.
125.7 cm
50cm
60cm
220-240 V / 50 Hz
130 W
0.98 kWh
138 l
42 l
136 l
42 l
2
“
“
“
“
“
“
“
“
“
“
“
“
“
“
“
“
“
“
WARNINGS
IT IS MOST IMPORTANT THAT THIS INSTRUCTION
BOOK SHOULD BE RETAINED WITH THE APPLIANCE
FOR FUTURE REFERENCE. SHOULD THE APPLIANCE
BE SOLD OR TRANSFERRED TO ANOTHER OWNER, OR
SHOULD YOU MOVE HOUSE AND LEAVE THE
APPLIANCE, ALWAYS ENSURE THAT THE BOOK IS
SUPPLIED WITH THE APPLIANCE IN ORDER THAT
THE NEW OWNER CAN GET TO KNOW THE
FUNCTIONING OF THE APPLIANCE AND THE
RELEVANT WARNINGS.
THESE WARNINGS ARE PROVIDED IN THE INTEREST
OF SAFETY. YOU MUST READ THEM CAREFULLY
BEFORE INSTALLING OR USING THE APPLIANCE.
This appliance is designed to be operated by
adults. Children should not be allowed to tamper
with the controls or play with the product.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
This product should be serviced by an authorised
ZANUSSI Service Centre, and only genuine
spare parts should be used.
It is dangerous to alter the specifications or
modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
ZANUSSI domestic refrigerators, freezers and
fridge/freezers are designed to be used
specifically for the storage of edible foodstuffs
only.
The cooling plate or refrigerated freezer shelves
in this appliance contain channels through which
the refrigerant passes. If these are punctured
this would cause substantial damage to the
appliance and result in food loss. DO NOT USE
SHARP INSTRUMENTS to scrape off frost or
ice. Under NO circumstances should solid ice be
forced off the lining or shelves. Solid ice should be
allowed to thaw, when defrosting the appliance.
See Defrost instructions.
The appliance should be left for 2 hours after
installation before it is turned on in order to allow
the refrigerant to settle.
This appliance is heavy. Care should be taken
when moving it.
Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or “frost/freezer burns”.
Ice lollies can cause “frost/freezer burns” if
consumed straight from the freezer.
Manufacturers’ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Refer to your local
ZANUSSI Service Centre and always insist on
genuine spare parts.
There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
possible food loss. See installation instructions.
Parts which heat up should not be exposed.
Wherever possible, the back of the appliance
should be close to a wall but leaving the required
distance for ventilation as stated in the
installation instructions.
Before defrosting, cleaning or maintenance work
is carried out, be sure to switch off the appliance
and unplug it.
Frozen food must NOT be re-frozen once it has
thawed out.
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance.
2222 038-64
3
CONSERVATION
In the interests of the Environment:
When disposing of your old fridge, freezer or fridge/
freezer.
Help to keep your country tidy – use authorised
disposal sites for your old appliances.
INSTALLATION
Warning
IF YOU ARE DISCARDING AN OLD
APPLIANCE THAT HAS A LOCK OR CATCH
ON THE DOOR, YOU MUST ENSURE THAT IT
IS MADE UNUSABLE TO PREVENT YOUNG
CHILDREN BEING TRAPPED INSIDE.
Depending upon the position you choose for your
appliance, you may wish to reverse the way in which
the door opens. T o do this, refer to instructions on
“Door reversal directions” paragraph.
For maximum efficiency:
Make sure that the appliance is cleaned properly.
Make sure that the door is closed properly.
Do not position the appliance near to sources of
heat.
Do not over-fill your appliance, air MUST be
allowed to circulate.
install in places with restricted ventilation.
Adjust the level of the appliance by screwing out
the adjustable foot, or feet, at the bottom of the
cabinet using your fingers or a spanner (see Fig. 2).
Fig. 2
Positioning
This appliance is designed to operate in ambient
temperatures between 10
It should be located in a dry atmosphere, out of direct
sunlight and away from extreme temperature e.g.
not next to a cooker or other sources of direct heat,
or in a very cold room e.g. an outhouse, where the
temperatures may fall below 10
temperatures are exceeded i.e. colder or warmer,
then the appliance may not operate correctly.
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There must
also be at least 100 mm (4”) distance between the top of
the cabinet and any overhanging kitchen furniture
(Fig. 1-A). Ideally , the appliance should not be
positioned beneath overhanging furniture (Fig. 1-B).
100 mm 10 mm
°C (50 °F) and 32 °C (90 °F).
°C (50 °F). If these
Fig. 1
D200
Before using
Remove all securing tapes. W ash inside the appliance
with lukewarm water and a little bicarbonate of soda
(one teaspoonful to one quart of water). Do not use
soap or detergent as the smell might linger. Dry
thoroughly.
Rear spacers
The plastic bag containing all relevant
documentation also contains two spacers to be fitted
into special holes in the back of the appliance.
Fit the spacers into the holes, taking care to ensure
that the arrow (A) is positioned as shown in Fig. 2a.
Then turn them through 45
until they lock into place.
° (arrow (A) vertical)
Fig. 2a
A
NP005
There should also be a gap of 25 mm either side of
the appliance. Do not obstruct the space
underneath. The back of the cabinet may be placed
close to the wall but must not touch it. DO NOT
4
B
10 mm
A
45°
D060
The electrical connections
WARNING: THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should this safety
measure not be observed.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow- Earth
Blue- Neutral
Brown- Live
If you fit your own plug, the colours of the wires in
the mains lead of your appliance may not
correspond with the markings identifying the
terminals in your plug, proceed as follows:
A replacement cover/carrier must be obtained from
your local Zanussi Service Force Centre whose
address is listed in the Customer Care Booklet
which accompanies your instruction manual.
This appliance complies with the E.E.C. Directive No. 87/308
of 2.6.87 relative to radio interference suppression.
This appliance complies with the following
E.E.C. Directives:
73/23 EEC of 19.2.73 (Low Voltage Directive) and
subsequent modifications;
89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
Fig. 3
GREEN & YELLOW
BLUE
D207
13 AMP. FUSE
13 AMP
BROWN
CORD CLAMP
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol , or coloured green and
yellow.
Connect the blue (neutral) wire to the terminal in
the plug which is marked with the letter «N» or
coloured black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or
coloured red.
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BSI362 fuse. Only
ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier
is lost. The cover/carrier is indicated by the
coloured insert at the base of the plug.
5
Loading...
+ 10 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.