Zanussi ZDF4010 User Manual [nl]

EN

User manual 2

FR

Notice d'utilisation 18

ES

Manual de instrucciones 36

Dishwasher
Lave-vaisselle
Lavavajillas

ZDF4010

Contents

Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3
Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5
Use of the appliance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Setting the water softener _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Use of dishwasher salt _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7
Use of rinse aid _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
Loading cutlery and dishes _ _ _ _ _ _ _ _ _ _ _ _ 8
Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10

Safety information

For your safety and correct operation of the appli-

ance, read this manual carefully before installation
and use. Always keep these instructions with the appli­ance even if you move or sell it. Users must fully know
the operation and safety features of the appliance.

Correct use

• The appliance is designed exclusively for domestic

use.

• Only use the appliance to clean household utensils

that are applicable for dishwashers.

• Do not put solvents in the appliance. Risk of explosion.

• Put the knives and all items with sharp points in the

cutlery basket with their points down. If not, put in a
horizontal position in the upper basket.

• Use only branded products for dishwashers (deter-

gent, salt, rinse aid).

• If you open the door while the appliance is in opera-

tion, hot steam can escape. Risk of skin burns.

• Do not remove dishes from the dishwasher before

the end of the washing programme.

• When the washing programme is completed, discon-

nect the mains plug from the mains socket and close
the water tap.

• Only an authorised service engineer can repair this

appliance. Use only original spare parts.

• Do not do repairs yourself to prevent injury and dam-

age to the appliance. Always contact your local Serv­ice Force Centre.

2

Multitab function _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Setting and starting a washing programme _ _ _ _ 11
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12
What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 15
Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ 15
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 16
Water connection _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 16
Electrical connection _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 17

Subject to change without notice

General safety

• Persons (including children) with reduced physical
sensory, mental capabilities or lack of experience
and knowledge must not use the appliance. They
must have supervision or instruction for the opera­tion of the appliance by a person responsible for
their safety.

• Obey the safety instructions from the manufacturer of
the dishwasher detergent to prevent burns to eyes,
mouth and throat.

• Do not drink the water from the dishwasher. Deter­gent residues can stay in your appliance.

• Always close the door when you do not use the appli­ance to prevent injury and not to stumble over the
open door.

• Do not sit or stand on the open door.

Child safety

• Only adults can use this appliance. Children must
get supervision to make sure that they do not play
with the appliance.

• Keep all the packaging away from children. There is
a risk of suffocation.

• Keep all detergents in a safe area. Do not let children
touch the detergents.

• Keep children away from the appliance when the
door is open.

Installation

• Make sure that the appliance is not damaged be­cause of transport. Do not connect a damaged appli­ance. If necessary, contact the supplier.

• Remove all packaging before first use.

• A qualified and competent person must do the electri­cal installation.

• A qualified and competent person must do the plumb­ing installation.

• Do not change the specifications or modify this prod­uct. Risk of injury and damage to the appliance.

• Do not use the appliance:
– if the mains cable or water hoses are damaged,

Control panel

– if the control panel, worktop or plinth area are dam-

aged, that you can get access to the inner side of
the appliance.

Contact your local Service Force Centre.

• Do not drill into the sides of the appliance to prevent
damage to hydraulic and electrical components.

Warning! Carefully obey the instructions for
electrical and water connections.

54

13

ABCDE

6

1 On/off button
2 Programme selection buttons
3 Delay start button
4 Indicator lights
5 Digital display
6 Function buttons

Indicator lights

Programme-in-progress – Comes on when you select a washing programme.

– Stays on for all the duration of the washing programme.
– Goes off at the end of the washing programme.

2

3

Indicator lights

End-of-programme Comes on when the washing programme is completed.

Multitab Comes on when you activate the multitab function. Refer to 'Multitab function'.

Salt

1)

Comes on when it is necessary to fill the salt container. Refer to 'Use of dishwash­er salt'.
After you fill the container, the salt indicator light can continue to stay on for some
hours. This does not have an unwanted effect on the operation of the appliance.

Rinse aid

1)

Comes on when it is necessary to fill the rinse aid container. Refer to 'Use of rinse
aid'.

1) When the salt and/or rinse aid containers are empty, the related indicator lights do not come on while a washing programme
operates.

Programme selection buttons

With these buttons you can select the washing pro­gramme. Press a programme button, the related indica­tor light comes on. Refer to 'Washing programmes' chap­ter for more data about the washing programmes.

Delay start button

Use the delay start button to delay the start of the wash­ing programme with an interval between 1 and 19
hours. Refer to the chapter 'Setting and starting a wash­ing programme'.

Digital display

The display shows:

• the set level of the water softener.

• Remaining time to the end of the programme.

• Activation/deactivation of the rinse aid dispenser (on-

ly with multitab function on).

• End of the washing programme. The display shows a

zero.

• Number of hours in delay start.

• Fault codes.

Function buttons

Use the function buttons for these operations:

• To set the water softener. Refer to the chapter 'Setting

the water softener'.

• To cancel the washing programme in progress or a
delay start in progress. Refer to the chapter 'Setting
and starting a washing programme'.

• To activate/deactivate the multitab function. Refer to
the chapter 'Multitab function'.

• To deactivate/activate the rinse aid dispenser, when
multitab function is active. Refer to the chapter 'Mul­titab function'.

Setting mode

The appliance must be in setting mode for these
operations:

• To set a washing programme.

• To set the water softener level.

• To deactivate/activate the rinse aid dispenser.

Press the on/off button. The appliance is in setting
mode when:

– All the programme indicator lights come on.
Press the on/off button. The appliance is not in setting

mode when:
– Only one programme indicator light comes on
– A washing programme is set. It is necessary to can-

cel the programme to go back to the setting mode.
Refer to the chapter 'Setting and starting a washing
programme".

4

Washing programmes

Washing programmes

Programme Degree of soil Type of load Programme description

Heavy soil Crockery, cutlery,

pots and pans

1)

Any Crockery, cutlery,

pots and pans

2)

Normal or light

Crockery and cutlery Main wash up to 65°C

soil

3)

Normal soil Crockery and cutlery Prewash

Any Partial load (to be

completed later in
the day).

1) During the Auto programme, the soil level of the dishes is given by how cloudy the water is. The programme duration and
consumptions can change. This depends if the appliance is fully or not and on the level of soil on the dishes. The appliance
adjusts automatically the temperature of the water during the main wash.

2) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want to load breakfast and
dinner crockery and cutlery.

3) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.

Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying

Prewash
Main wash up to 45°C or 70°C
1 or 2 intermediate rinses
Final rinse
Drying

Final rinse

Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying

1 cold rinse (to prevent food scraps to bond).
Detergent is not necessary with this programme.

Consumption values

Programme

1) The digital display shows the programme duration.

The pressure and temperature of the water, the var­iations of power supply and the quantity of dishes

can change these values.

Duration (in minutes)

- 1,6-1,8 22-24

- 1,1-1,8 12-23

- 0,9 9

- 1,0-1,1 13-15

- 0,1 4

1)

Energy (in kWh) Water (in litres)

5

Use of the appliance

Refer to the following instructions for each step of pro­cedure:

1. Make a check if the water softener level is correct

for the water hardness in your area. If necessary set
the water softener.

2. Fill the salt container with dishwasher salt.

3. Fill the rinse aid dispenser with rinse aid.

4. Load cutlery and dishes into the dishwasher.

5. Set the correct washing programme for the type of
load and soil.

6. Fill the detergent dispenser with the correct quanti­ty of detergent.

7. Start the washing programme.

If you use combi detergent tablets ('3 in 1', '4 in
1', '5 in 1', etc.), refer to the chapter 'Multitab func-

tion'.

Setting the water softener

The water softener removes minerals and salts from the
water supply. Minerals and salts can have bad effect on
the operation of the appliance.
Water hardness is measured in equivalent scales:

• German degrees (dH°).

• French degrees (°TH).

Water hardness Water hardness setting

°dH °TH mmol/l Clarke manually electronically

51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10
43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9
37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8
29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7
23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6
19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5
15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4
11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3

4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2

< 4 < 7 < 0,7 < 5

1) No use of salt required.

• mmol/l (millimol per litre - international unit for the
hardness of water).

•Clarke.

Adjust the water softener to the water hardness in your
area. If necessary, contact your local water authority.

1)

1

1)

1

You must set the water softener manually and elec­tronically.

Manual adjustment

The appliance is set at the factory at position 2.

6

1

2

Set switch to position 1
or 2.

Electronic adjustment

The water softener is set at the factory at level 5.

1. Switch on the appliance.

Use of dishwasher salt

Caution! Only use dishwashers salt. Types of salt
that are not applicable for dishwashers cause

damage to the water softener.

2. Make sure that the appliance is in setting mode.

3. Press and hold function buttons B and C until the

indicator lights of function buttons A, B and C start
to flash.

4. Release function buttons B and C.

5. Press function button A.

– The indicator lights for function buttons B and C

go off.

– The indicator light for function button A contin-

ues to flash.

– The digital display shows the current level.
Example: digital display shows

6. Press the function button A one time to increase the

water softener level by one step.

7. Press the on/off button to save the operation.

= level 5.

1

3

Fill the salt container with
1 litre of water (only the
first operation).

5

It is normal that water overflows from the salt con-

2

4

tainer when you fill it with salt.
Make sure that there is no grain of salt outer of

the salt compartment. Salt which stays on the tank
for a while drills the tank. It is recommended to start a
washing programme immediately after you fill the salt
container. This prevents of corrosion because of spilled
salt.

When you set electronically the water softener to level
1, the salt indicator light does not stay on.

6

7

Use of rinse aid

Caution! Only use branded rinse aid for
dishwashers.

Do these steps to fill the rinse aid dispenser:

1 2

A

X

M

+

1

4

2

3

3

4

Loading cutlery and dishes

Helpful hints and tips

Caution! Only use the appliance for household
utensils that are applicable for dishwashers.

Do not use the appliance to clean objects that can ab­sorb water (sponges, household cloths, etc.).

• Before you load cutlery and dishes, do these steps:
– Remove all food remainings and debris.
– Make burnt, remaining food in pans soft.

• While you load cutlery and dishes, do these steps:
– Load hollow items (e.g. cups, glasses and pans)

with the opening down.

– Make sure that water does not collect in the con-

tainer or in a deep base.

– Make sure that cutlery and dishes do not lie in-

side one another.

– Make sure that cutlery and dishes do not cover oth-

er cutlery and dishes.

Caution! Do not fill the rinse aid dispenser with

other products (e.g. dishwasher cleaning agent,
liquid detergent). There is a risk of damage to the ap­pliance.

Adjusting the dosage of rinse aid

The rinse aid dial is set at
the factory at position 3.

A

X

M

+

1

4

2

3

– Make sure that glasses do not touch other glasses.
– Put small objects in the cutlery basket.

• Plastic items and pans with non-stick coatings can
keep water droplets. Plastic items do not dry as well
as porcelain and steel items.

• Put light items in the upper basket. Make sure that
the items do not move.

Caution! Make sure that the spray arms can move
freely before you start a washing programme.

Warning! Always close the door after you load or
unload the appliance. An open door can be

dangerous.

To increase or decrease
the dosage refer to 'What
to do if...'

8

1

Arrange service dishes
and large lids around the
edge of the lower basket.

2

1

Arrange the items to let
water touch all surfaces.

Prevent to put plates in the first three sections in
the front part of the upper basket. Make sure the

plates tilt forward.

2

For longer items fold the
cup racks up.

Adjustment of the height of the upper basket

If you put large plates in the lower basket, first move the
upper basket to the upper position.

3

The rows of prongs in the
lower basket can be flat
to load pots, pans and
bowls.

1 2

Use the cutlery grid. If the dimensions of the cut­lery prevent use of the cutlery grid, remove it.

Maximum height of the dishes

upper basket lower basket

Upper position 20 cm 31 cm
Lower position 24 cm 27 cm

Do these steps to move the upper basket to the upper
position:

1. Pull the basket out until it stops.

2. Carefully lift the two sides until the mechanism is
engaged and the basket is stable.

1

Do these steps to move the upper basket to the lower
position:

1. Pull the basket out until it stops.

2. Carefully lift the two sides upwards.

3. Hold the mechanism and let it fall back down slowly.

9

Caution!

• Do not lift or lower the basket on one side only.

Use of detergent

Only use detergents (powder, liquid or tablet) that
are applicable for dishwashers.

Follow the data on the packaging:

• Dosage recommended by the manufacturer.

• Storage recommendations.
Do not use more than the correct quantity of deter-

gent to save an environment.

• If the basket is in the upper position, do not put cups
on the cup racks.

5

Different brands of detergent dissolve in different

times. Some detergent tablets do not have the
best cleaning results during short washing pro­grammes. Use long washing programmes when you
use detergent tablets to fully remove the detergent.

6

1

3

Fill the detergent dispens­er (A) with detergent.

2

4

If you use a washing pro­gramme with prewash
phase, put more deter­gent in the prewash deter­gent compartment (B).

Multitab function

The multitab function is for combi detergent tablets.
These tablets contain agents such as detergent, rinse
aid and dishwasher salt. Some types of tablets can con­tain other agents.
Do a check if these tablets are applicable for the local
water hardness. Refer to the instructions from the manu­facturer.

When you set the multitab function, it stays on until you
deactivate it.
The multitab function stops automatically the flow of
rinse aid and salt. The rinse aid indicator light and salt
indicator light are deactivated.
The programme duration can increase if you use the mul­titab function.

10

Activate or deactivate the multitab function before

the start of a washing programme.
You cannot activate or deactivate the multitab function
when the programme operates. Cancel the washing pro­gramme, then set the programme again.

To activate the multitab function:

• Press and hold the two multitab buttons (function but-

tons D and E). The multitab indicator light comes on.

To deactivate the multitab function:

• Press and hold the two multitab buttons (function but-

tons D and E). The multitab indicator light goes off.

Do these steps if the drying results are not satis-

factory:

1. Fill the rinse aid dispenser with rinse aid.

2. Activate the rinse aid dispenser.

3. Set the rinse aid dosage to position 2.

• You can only activate or deactivate the rinse aid dis-

penser when the multitab function is activated.

To activate/deactivate the rinse aid dispenser:

1. Switch on the appliance.

2. Make sure that the appliance is in setting mode.

3. Press and hold function buttons B and C.

– The indicator lights for function buttons A, B,

and C start to flash.

4. Release function buttons B and C.

5. Press function button B.
– The indicator lights for function buttons A and C

go off.

– The indicator light for function button B contin-

ues to flash.

– The digital display shows the setting.

Rinse aid dispenser deac­tivated

Rinse aid dispenser activa­ted

6. Press function button B again.
– The digital display shows the new setting.

7. Switch off the appliance to save the operation.

To use normal detergent again:

1. Deactivate the multitab function.

2. Fill the salt container and rinse aid dispenser.

3. Adjust the water hardness setting to the highest level.

4. Do a washing programme without dishes.

5. Adjust the water softener to the water hardness in
your area.

6. Adjust the rinse aid dosage.

Setting and starting a washing programme

Set the washing programme with the door ajar.

The washing programme only starts after you
close the door. Until then it is possible to modify the set­tings.

Do these steps to set and start a washing programme:

1. Switch on the appliance.

2. Make sure that the appliance is in setting mode.

3. Press one of the programme buttons. Refer to the

chapter 'Washing programmes'.
– The programme indicator light comes on.
– All other programme indicator lights go off.
– The digital display shows in flashing the pro-

gramme duration.

– The programme-in-progress indicator light

comes on.

4. Close the door.

– The washing programme starts automatically.
– The programme-in-progress indicator light re-

mains on.

When the washing programme operates, you can­not change the programme. Cancel the washing

programme.

You can select the washing programme and delay

start also with the door closed. When you press a
programme button you have only 3 seconds to select a
different washing programme or a delay start. After
these 3 seconds, the selected programme starts automat­ically.

Warning! Only interrupt or cancel a washing

programme if necessary.

Caution! Open the door carefully. Hot steam can

come free.

11

Cancelling a washing programme

1. Press and hold function buttons B and C until:
– All the programme lights come on,
– The programme-in-progress indicator light goes

off.

2. Release function buttons B and C to cancel the wash­ing programme.

At this time you can do these steps:

1. Switch off the appliance.

2. Set a new washing programme .

Fill the detergent dispenser with detergent before you
set a new washing programme.

Interrupting a washing programme

Open the door.

• The programme stops.

Close the door.

• The programme continues from the point of interrup-

tion.

Setting and starting a washing programme with
delay start

1. Press the on/off button.

2. Set a washing programme.

3. Press the delay start button until the display shows
on flashing the necessary delay start of the washing
programme.

4. Close the door.
– The number on the display comes on with fixed

light.

– The programme-in-progress indicator light goes

off.
– The countdown of the delay start starts.
– The countdown of the delay start decreases with

steps of 1 hour.
– When the countdown is completed, the washing

programme starts automatically.

– The programme-in-progress indicator light

comes on.

Do not open the door during the countdown to pre-

vent interruption of the countdown. When you
close the door again, the countdown continues from the
point of interruption.

Cancelling a delay start:

1. Press and hold function buttons B and C until:

– All the programme lights come on.
When you cancel a delay start, you also cancel the
washing programme.

2. Set a new washing programme.

End of the washing programme

• The appliance stops automatically.

• The display shows 0.

• The end-of-programme indicator light comes on.

• The programme-in-progress indicator light goes off.

1. Switch off the appliance.

2. Open the door.

3. For better drying results, keep the door ajar for

some minutes before you remove the dishes.
Let the dishes cool down before you remove them from
the appliance. Hot dishes are easily damaged.

Removing the load

• First remove items from the lower basket, then from

the upper basket.

• There can be water on the sides and door of the appli-

ance. Stainless steel becomes cool more quickly
than the dishes.

Standby mode

If you do not switch off the appliance at the end of the
washing programme, the appliance automatically goes
into standby mode. The standby mode decreases ener­gy consumption.
Three minutes after the end of the programme, all indi­cator lights go off and the digital display shows one hor­izontal bar.
Press one of the buttons (not the on/off button), to go
back to end-of-programme mode.

Care and cleaning

Warning! Switch the appliance off before you
clean the filters.

12

Cleaning the filters

Important! Do not use the appliance without the filters.
Make sure that the installation of the filters is correct.

Incorrect installation will cause unsatisfactory washing
results and damage to the appliance.

1 2

Fully clean the filters A, B
and C below running wa­ter.

Important! Do not remove the spray arms.
If the holes in the spray arms become clogged, remove

remaining parts of soil with a cocktail stick.

External cleaning

Clean the external surfaces of the appliance and control
panel with a damp soft cloth. Only use neutral deter­gents. Do not use abrasive products, scouring pads or
solvents (acetone, trichloroethylene etc...).

Frost precautions

Caution! Do not install the appliance where the
temperature is below 0 °C. The manufacturer is

not responsible for damage because of frost.
If not possible, empty the appliance and close the door.

Disconnect the water inlet hose and remove water from
the water inlet hose.

3

To remove filters B and
C, turn the handle approx­imately 1/4 anticlockwise.

5

Put the flat filter A in the
bottom of the appliance.
Install the flat filter cor­rectly under the two
guides D.

4

Remove the flat filter A
from the bottom of the ap­pliance.

6

Put the filter system in po­sition. To lock the filter
system, turn the handle
clockwise until it locks in
position.

What to do if…

The appliance does not start or stops during operation. If there is a fault, first try to find a solution to the prob-

lem yourself. If you cannot find a solution to the prob­lem yourself, contact the Service Force Centre.

13

Caution! Switch off the appliance before you do
the below suggested corrective actions.

Fault code and malfunction Possible cause and solution

•

digital display shows

The dishwasher does not fill with water

•

digital display shows

The dishwasher will not drain

•

digital display shows

The anti-flood device operates
The programme does not start • The appliance door is not closed.

• The water tap is blocked or furred with limescale.
Clean the water tap.

• The water tap is closed.
Open the water tap.

• The filter in the water inlet hose is blocked.
Clean the filter.

• The connection of the water inlet hose is not correct. The hose can
be kinked or squashed.
Make sure that the connection is correct.

• There is a blockage in the sink spigot.
Clean the sink spigot.

• The connection of the water drain hose is not correct. The hose can
be kinked or squashed.
Make sure that the connection is correct.

• Close the water tap and contact your local Service Force Centre.

Close the door.

• Mains plug is not connected in.
Put in the mains.

• The fuse has blown out in the household fuse box.
Replace the fuse.

• Delay start is set.
Cancel the delay start to start the programme immediately.

After the check, switch on the appliance. The pro­gramme continues from the point of interruption. If the
malfunction shows again, contact your Service Force
Centre.
If the display shows a fault code, not described in the
chart, contact your Service Force Centre.
These data are necessary to help you quickly and cor­rectly:

• Model (Mod.)

14

• Product number (PNC)

• Serial number (S.N.)
For these data, refer to the rating plate.
Write the necessary data here:

Model description : ..........

Product number : ..........

Serial number : ..........

The cleaning results are not satisfactory

The dishes are not clean • The selected washing programme is not applicable for the type of load and

soil.

• The baskets are loaded incorrectly so that water cannot reach all surfaces.

• Spray arms do not turn freely because of incorrect arrangement of the load.

• The filters are dirty or not correctly installed.

• The quantity of detergent is too little or missing.

Limescales particles on the dishes • The salt container is empty.

• The water softener is adjusted on a wrong level.

• The salt container cap is not closed correctly.

The dishes are wet and dull • No rinse aid has been used.

• The rinse aid dispenser is empty.

There are streaks, milky spots or
a bluish coating on glasses and
dishes

Dry water drop signs on glasses
and dishes

• Decrease the rinse aid dosage.

• Increase rinse aid dosage.

• The detergent can be the cause.

Technical data

Dimensions Width cm 60
Height cm 85
Depth cm 61
Electrical connection - Voltage -

Overall power - Fuse
Water supply pressure Minimum 0,5 bar (0,05 MPa)
Maximum 8 bar (0,8 MPa)
Capacity Place settings 12

Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher door.

Environment concerns

The symbol on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more

detailed information about recycling of this product,
please contact your local council, your household waste
disposal service or the shop where you purchased the
product.

The packaging materials are environmentally friendly
and can be recycled. The plastic components are identi­fied by markings, e.g. >PE<, >PS<, etc. Discard the pack­aging materials in the applicable container at the com­munity waste disposal facilities.

15

Warning! To discard the appliance, follow the
procedure:

• Pull the mains plug out of the socket.

• Cut off the mains cable and mains plug and discard
them.

Installation

Warning! Make sure that mains plug is
disconnected from the mains socket during

installation.

Fitting under a counter

Put the appliance adjacent to a water tap and a water
drain. Remove the appliance worktop to install it under
a sink unit or a kitchen worktop. Make sure that the di­mensions of the recess agree with the given dimensions.

1 2

• Discard the door catch. This prevents the children to
close themselves inside the appliance and endanger
their lives.

3

Install the appliance worktop to the appliance if you
want to use the dishwasher as a freestanding appliance.
The plinth on freestanding appliance is not adjustable.

4

Adjusting the level of the appliance

Make sure that the appliance is level to close and seal
the door correctly. If the level of the appliance is cor­rect, the door does not catch on the sides of the cabinet.
If the door does not close correctly, loosen or tighten
the adjustable feet until the appliance is level.

Water connection

Water inlet hose

Connected the appliance to a hot (max. 60°) or cold wa­ter supply.
If the hot water comes from alternative sources of ener­gy that are more environmentally friendly (e.g. solar or
photovoltaic panels and aeolian), use a hot water sup­ply to decrease energy consumption.
Connect the inlet hose to a water tap with an external
thread of 3/4”.

Caution! Do not use connection hoses from an
old appliance.

The water pressure must be in the limits (refer to the
chapter 'Technical data'). Make sure that the local water
authority gives you the average mains pressure in your
area.

16

Make sure that there are no kinks in the water inlet hose
and that the water inlet hose is not squashed or entangled.
Turn the inlet hose to the left or the right to suit the in­stallation. Fit the locknut correctly to prevent water leaks.

Caution! Do not connect the appliance to new

pipes or pipes that are not used for a long time.
Let the water run for some minutes, then connect the
inlet hose.