York Fitness YYRK52085A Owner's Manual
Owner’s Manual
Performance Elliptical Trainer
Item #YRK52085A
2
TABLE OF CONTENTS
SAFETY PRECAUTIONS
2
EXPLODED DIAGRAM
7-8
PRE-ASSEMBLY CHECK LIST
3
ASSEMBLY INSTRUCTIONS
9-13
HARDWARE PACKING LIST
4
COMPUTER INSTRUCTIONS
14-15
PARTS LIST
5-6
EXERCISE INSTRUCTIONS
16-17
WARRANTY
18-20
IMPORTANT SAFETY PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply whenever
you operate a piece of exercise equipment. Be sure to read the entire manual before you
assemble or operate your machine. In particular, note the following safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave children
unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or
outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp objects around the machine.
9. Disabled persons should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. The max. user capacity is 100 KGS.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35
OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS
BEFORE USING ANY FITNESS EQUIPMENT.
SAVE THESE INSTRUCTIONS
2
3
PRE-ASSEMBLY CHECK LIST
NO:1
NO:2 NO:3
NO:22
NO:9L/R
NO:39
NO:13L/R
NO:38
NO:37L/R NO:21L/R
NO:25
PART NO.
DESCRIPTION
Q’TY
1
Main frame
1
9L/R
Pedal tube L/R
1/1
39
Handlebar 1 2
Rear stabilizer 1 3
Front stabilizer
1
13L/R
Pedal L/R
1/1
39
Console
1
22
Front support
1
25
Tension control knob w/cable
1
37L/R
Top handlebar L/R
1/1
21L/R
Bottom handlebar L/R
1/1
Manual
1
3
4
HARDWARE PACKING LIST
NO.
DESCRIPTION
QTY
DRAWING
6
Carriage bolt M8*60
4
6
7
7
Curved washerΦ8*Φ20*1.5
10
8
Domed nut M8
4
8
10
10
Hinge bolt L/R
1/1
11
Wave washer
2
11
12
12
Flat washer
2
14
Allen bolt M8*20
4
14
15
15
PVC cap
6
16
Nylon nut M10
2
16
17
17
Flat washer Φ22*Φ10*1.5
2
18
Sleeve
2
18
20
20
Hex head bolt M10*65
2
23
Allen bolt M8*16
6
23
29
29
Hex head bolt M10*20
2
30
Spring wash Φ10
2
30
31
31
Flat washer Φ32*Φ10*1.5
2
32
D type washer
2
32
35
35
Allen bolt M6*12
4
36
Hollow carriage boltΦ8*20
4
36
51
51
Nut L/R
1/1
Allen key (6mm)
1
Allen key（4mm）
1
Allen key（8mm）
1
Box wrench
2
4
5
PARTS LIST
ITEM NO.
DESCRIPTION
Q’TY
1
Main frame
1
2
Rear stabilizer
1
3
Front stabilizer
1
4
End cap for rear stabilizer
2
5
End cap for front stabilizer
2
6
Carriage bolt M8*60
4
7
Curved washer Φ8*Φ20*1.5
10
8
Domed nut M8
4
9L
Pedal tube L
1
9R
Pedal tube R
1
10L
Hinge bolt L
1
10R
Hinge bolt R
1
11
Wave washer
2
12
Flat washer
2
13L
Pedal L 1 13R
Pedal R 1 14
Allen bolt M8*20
4
15
PVC cap
6
16
Nylon nut M10
2
17
Flat washer Φ22*Φ10*1.5
2
18
Sleeve 2 19
Upper sensor wire
1
20
Hex head bolt M10*65
2
21L
Bottom handlebar L
1
21R
Bottom handlebar R
1
22
Front support
1
23
Allen bolt M8*16
6
24
Belt pulley w/ crank
1
25
Tension control knob w/cable
1
26
Middle sensor wire
1
27
Extension tension cable
1
28
Lower sensor wire
1
29
Hex head bolt M10*20
2
30
Spring washer Φ10
2
31
Flat washer Φ32*Φ10*1.5
2
32
D type washer
2
33
Upper pulse wire
2
34
Front support axle cover
2
35
Allen bolt M6*12
4
36
Carriage boltΦ8*20
4
5
6
PARTS LIST
ITEM NO.
DESCRIPTION
Q’TY
37L
Top handlebar L
1
37R
Top handlebar R
1
38
Console 1 39
Handlebar
1
40
End cap 4 41
Hand pulse sensor
2
42
Self-tapping screw
2
43
Flat washer Φ6*Φ12*1
2
44
Foam grip for handlebar
2
45
Foam grip for top handlebar
2
46
Lower pulse wire
2
47
Grommet
1
49
Flat washer
1
50
Blot
1
51L
Nut L
1
51R
Nut R 1 52L
Chain cover L
1
52R
Chain cover R
1
53
End cap for chain cover
2
54
Self-tapping screw ST5*15
8
55
Self-tapping screw ST5*15
4
56
Flywheel
1
57
Flange nut
2
58
Adjusting screw
2
59
U-type bracket
2
60
Nylon nut M6
2
61
Snap spring
2
62
Axle for flywheel
1
63
Hex head bolt M8*55
1
64
Plastic spacer
2
65
Magnet assembly
1
66
Crank bearing
1
67
Belt
1
68
Sensor bracket
1
69
Spring
1
70
Hex head bolt M6*25
1
71
Hex head nut M6
2
72
Nylon nut M8
1
6
Loading...