York Fitness YBR AXT 120, 52069 Owner's Manual

Owner’s Manual

YBR AXT 120 Crosstrainer

Item #52069

www.yorkfitness.com

March 31, 2014

www.yorkfitness.com

2

Congratulations on
purchasing your exercise
equipment from

You have chosen a high quality, safe and innovative piece
of equipment as your training partner and we are certain
it will keep you motivated on the way to achieving your
personal tness goals.

Please take the time to read this owner’s manual as it
will help you to get the most out of your new exercise
equipment.

For more information visit www.yorktness.com

CONTENTS

Safety information 03

Customer support 04

Assembly instructions 05

Operational instructions 11

Troubleshooting 16

Fitness guide 18

Exploded drawing 20

Part list 22

Protect the environment by not disposing
of this product or batteries with household
waste. Check your local authority for
recycling advice and facilities.

Table of Contents

www.yorkfitness.comwww.yorkfitness.com

3

Please read this instruction manual before you begin
assembly. Great care has been taken to design these
instructions and following them will help you with quicker
assembly and minimize the risk of injury.

It is important that you keep these instructions for future
reference.

This list is not exhaustive - You are responsible for your own
safety!

• Always assemble and operate the equipment on a level
surface.

• Ensure the equipment is stable before use.

• Always ensure that the equipment has adequate space
on each side.

• Try to ensure that your back is straight while exercising,
especially for long periods.

• The safety level of this equipment can only be maintained
if it is regularly examined for wear and tear.

• Replace defective components immediately and keep
the equipment out of use until it is repaired.

• Use only the adjustment setting as described in the
instructions. Always use the correct adjustment pin /
xing.

• Always check that any pins / xings are tight and secure
before use and after adjustment.

• Never leave any adjustment devices projecting from the
equipment.

• Always consult your doctor before undertaking any
exercise program.

• Always wear suitable clothing and footwear. (e.g.
tracksuit / shorts / training shoes)

• Remove all personal jewelry before exercising.

• Ensure you warm-up well before using the equipment
as this will help to prevent muscle strain.

• After eating, allow 1-2 hours before exercising as this
will help to prevent muscle strain.

• Never overload the equipment. (See maximum user
weight)

• Never use the equipment in any other manner other
than the ways explained in these instructions and any
wall-chart supplied.

• Injuries to health may result from incorrect or excessive
training.

• Parents and others in charge of children should be
aware of their responsibility, because the natural play
instinct and the fondness of experimenting of children
can lead to situations and behavior for which the

training equipment is not intended.

• If children are allowed to use the equipment, their
mental and physical development and above all their
temperament should be taken into account. They
should be controlled and instructed in the correct use of
the equipment.

• The equipment is under no circumstances suitable as a
children’s toy.

• Children should not be allowed on or around the
equipment, especially when it is not in use.

• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.

• This product is not suitable for therapeutic purposes.

• This product has an integrated speed independent
braking system without a constant power mode that is
governed by magnetic resistance.

• This product has been tested for use in a home
environment and is warranted for In Home, personal,
family or household use.

• Due to our continuous policy of product development,
York Fitness reserves the right to change specications
without notice.

CAUTION! The instructions must be followed carefully in
the assembly, use and maintenance of your equipment.
The warranty does not cover damage due to negligence of
the assembly, adjustment and maintenance instructions
described herein.

Maximum user weight: 110kg

Safety Standards

This equipment meets the requirements of the EU’s EMC and
Low Voltage directives (where applicable), EN957 1 & 9 - CLASS
HC. Therefore the equipment carries the following marks:

Safety Information

www.yorkfitness.com

4

Should you require any assistance regarding this product
please gather the following information and then contact us
using the details below:

• Serial No. - This can be found on the sticker below, located as indicated.

• Original purchase date

• Place of purchase

• Information about the place and conditions of use

• Precise description of the issue / defect

Use only on a level surface
Not suitable for therapeutic purpose

Manufacturer: YORK BARBELL
Contact: York Way, Daventry, England, NN11 4YB
Product Name: YBR AXT 120 Crosstrainer
Max User Weight: 110KG
Safety Standards: EN957 Part 1 & 9 - Class HC
Electrical info: 9V / 500mA

SERIAL NO:

52069-

Product’s Name

Serial Number

This product label is an example only, it is not the real
product name and serial number of the item you
have bought.

Underside of the
main body.

IMPORTANT!! - Please retain your sales receipt, York Fitness Customer Care may request proof of
purchase to validate eligibility for warranty service. Warranty cover starts from the date shown on the
proof of purchase.

ENGLAND

The best way to contact us is via the website:
www.yorktness.com

York Barbell UK Ltd.

York Way, Daventry,
England, NN11 4YB
Tel: [phone]

AUSTRALIA

The best way to contact us is via the website:
www.yorktness.com.au

York Fitness Australia

1/2 Swaham Rd, Minto,
PO Box 5130, NSW 2566
Tel: [phone]

Customer Support

www.yorkfitness.comwww.yorkfitness.com

5

Prepare your work area - It is important you assemble the product in a clean and uncluttered space.

Work with a friend - We recommend you have someone assist you with the assembly as some of the components are quite heavy.

Open the carton - Check any warnings on the carton and make sure you have it the right way up.

Unpack the carton - Remove all the parts and lay them out on the oor.

Make sure you have the following parts:

Z E

BC J

K

O

I

LM

N

A

Assembly Instructions

www.yorkfitness.com

6

BLISTER PACK

1

3

4

5

N-1 x 4 (M8 x 1.25 x 75L)

N-3 x 4 (D22 x D8.5 x 1.5T)

N-5 x 8 (D14 x D6.5 x 0.8T)

N-6 x 8 (M6 x 1 x 15L)

N-7 x 2 (D29 x 21, M8)

N-4 x 2 (D15.4 x D8.2 x 2T)

N-10 x 2 (M8 x 1.25 x 25L)

N-4 x 10 (D15.4 x D8.2 x 2T)

N-3 x 10 (D22 x D8.5 x 1.5T)

N-11 x 1 (114 x 76 x 43)

N-12 x 10 (M8 x 1.25 x 20L)

N-14

N-14

N-13

N-9 x 2

(D25 x D8.5 x 2T)

N-8 x 2 (D26 x D19.5)

N-2 x 4 (M8 x 1.25 x 15L)

N-4 x 4 (D15.4 x D8.2 x 2T)

Assembly Instructions

www.yorkfitness.comwww.yorkfitness.com

7

1

Z

N-2

N-4

N-3

N-1

N-1 x 4

N-2 x 4

N-3 x 4

N-4 x 4

J

N-1

K

2

C-1

C-2

D-4

D-11

Z

www.yorkfitness.com

8

3

G-2

N-5

N-6

I

N-5 x 8

N-6 x 8

4

G-1

N-7

N-4

G-1

N-8

N-8

G-1

C

L

N-10

N-9

G-1

L

N-9 N-10

N-7N-4

N-8

N-8C

N-9 x 2

N-4 x 2

N-8 x 2

N-7 x 2

N-10 x 2

Assembly Instructions

www.yorkfitness.comwww.yorkfitness.com

9

5

E-2

E-1

G

C

N-12

N-4

N-3

N-3

N-12

N-11

B

N-4

N-3 x 10

N-4 x 10

N-12 x 10

6

A-1
A-2
C-2

B-6

C-1

C-4

O

A-2 x 4

pre-installed

www.yorkfitness.com

10

Final Check

Your exercise equipment is now assembled.
Please make the following nal checks:

• Make sure all screws / bolts are tightened.

• Make sure the equipment is on a at, level surface.

Input Power

Plug in the adaptor to the equipment then the computer
will produce a beep sound and turn on the computer at
the Manual mode.

Adaptor

WATER BOTTLE NOT INCLUDED.

Assembly Instructions

www.yorkfitness.comwww.yorkfitness.com

11

Hand Pulse Sensors

This cross trainer is tted with 2 hand pulse sensors. To obtain
a pulse reading you must have both your left and right hands
on the sensors at the same time. Do not grip the hand sensors
too tight and allow the computer a few seconds to display the
reading.

Hand Pulse Sensor

Adjusting The Resistance

This cross trainer features a speed independent braking
(resistance) system. The resistance is controlled by a magnet,
which is moved closer or further away from the ywheel - the
closer the magnet is to the ywheel the higher the resistance.
The magnet is computer controlled, to adjust simply use the UP /
DOWN key on the console.

Resistance Level

Levelling Your Cross Trainer

To help you level the cross trainer on uneven surface, 2 height
adjusters are included on the rear stabilizers. Simply twist these
around to adjust the height of the cross trainer.

Care & Maintenance

• This equipment should not be placed outdoors, in a garage or an outbuilding. Keep the equipment in a dry place
with as little temperature variation as possible.

• We recommend placing a mat beneath the equipment to protect both the equipment and your ooring.

• Always place the equipment in a dry environment.

• Use a warm, damp cloth to keep the product clean.

• No wet cleaning of electrical components. Unplug before any care and maintenance.

• The safety level of the equipment can be maintained only if it is regularly examined for damage and wear. This
includes any ropes, pulleys, nuts, bolts, moving parts, bushes, chains, wheels, bearings & connection points etc.

• Ensure that you inspect the product regularly - at least once a week is recommended.

• Ensure that all xings are tight before use.

• Always replace damaged / worn components with original parts from the manufacturer.

Operational Instructions

www.yorkfitness.com

12

Console:

BODY FAT RECOVERY DOWN UP RESET START/STOP

P1 P2

P3

P4

P5 P6

P12P11

P10P9P8

P7

MODE

Power On:

Plug in power supply and the computer will power on and display all segments for 2 seconds.

After power on the monitor for the rst time, the user will be prompted to enter his / her age, sex, height and weight. Use
the UP / DOWN buttons to change the value and press the MODE key to conrm each setting. The monitor will enter the
home screen after the setup.

Stand-by Mode:

The LCD monitor will enter stand-by mode after 4 minutes of inactivity.
Press on any key to wake the monitor.

Operational Instructions

www.yorkfitness.comwww.yorkfitness.com

13

Key Function:

KEY DESCRIPTION

UP • Increase resistance level.

• Setting selection.

DOWN • Decrease resistance level.

• Setting selection.

MODE • Conrm setting or selection.

RESET • Press the RESET button once to go back to main menu during setup.

• Press and hold the RESET button for 2 seconds to reboot computer and start from default
setting.

START / STOP • Start / Stop a workout program.

RECOVERY • Test your heart rate recovery. (See the “Recovery Mode” section)

BODY FAT • Test your body fat % and BMI. (See the “Body Fat Mode” section)

Display Function:

DISPLAY DESCRIPTION

TIME • Display the workout time during exercise.

• Range 0:00 ~ 99:59

SPEED • Display the workout speed during exercise.

• Range 0.0 ~ 99.9

DISTANCE • Display the workout distance travelled during exercise.

• Range 0.0 ~ 99.9

CALORIES • Display the calories burnt during exercise.

• Range 0 ~ 999

PULSE • Display the user pulse (bpm) during exercise.

• An alarm will sound if your pulse is over the preset target.

RPM • Display the rotation per minute during exercise.

• Range 0 ~ 999

WAT T • Display the power consumption during exercise.

• In Watt Program mode, computer will remain preset watt value during exercise. (Setting
range 0~350)

MANUAL • Display the manual mode workout.

PROGRAM • Display the preset resistance level prole of the selected program mode.

USER • Display the user resistance level prole during a user mode workout.

H.R.C. • Display the H.R.C. mode workout.

www.yorkfitness.com

14

Manual Mode

User can begin manual mode by pressing the START button in main menu.

1. Use the UP / DOWN buttons to select MANUAL and press MODE to conrm.

2. Use the UP / DOWN buttons to preset a target TIME, DISTANCE, CALORIES or PULSE.
Press MODE to conrm.

3. Press on the START/STOP button to begin workout. Use the UP / DOWN buttons to adjust load level during exercise.

4. Press on the START/STOP button to pause. Press RESET to return to the main menu.

Program Mode

1. Use the UP / DOWN buttons to select one of the twelve preset programs and press
MODE to conrm.

2. Use the UP / DOWN buttons to set a workout time.

3. Press on the START/STOP button to begin workout. Use the UP / DOWN buttons to adjust load level during exercise.

4. Press on the START/STOP button to pause. Press RESET to return to the main menu.

User Program Mode

1. Use the UP / DOWN buttons to select a user program and press MODE to conrm.

2. Use the UP / DOWN buttons to set a load level for the rst column and press MODE to select the next column. Repeat
this step for all 20 columns.

3. Press and hold on the MODE button to nish or quit the setup.

4. Use the UP / DOWN buttons to set a workout time.

5. Press on the START/STOP button to begin workout. Use the UP / DOWN buttons to adjust load level during exercise.

6. Press on the START/STOP button to pause. Press RESET to return to the main menu.

H.R.C. Mode

1. Use the UP / DOWN buttons to select H.R.C. and press MODE to conrm.

2. Use the UP / DOWN buttons to select 55%, 75%, 90% or TAG (Target H.R. - default: 100).

3. Use the UP / DOWN buttons to set a workout time.

4. Press on the START/STOP button to begin workout.

5. Press on the START/STOP button to pause. Press RESET to return to the main menu.

Operational Instructions

www.yorkfitness.comwww.yorkfitness.com

15

WATT Mode

1. Use the UP / DOWN buttons to select WATT and press MODE to conrm.

2. Use the UP / DOWN buttons to select a WATT target (Default: 120).

3. Use the UP / DOWN buttons to set a workout time.

4. Press on the START/STOP button to begin workout. Use the UP / DOWN buttons to adjust WATT level.

5. Press on the START/STOP button to pause. Press RESET to return to the main menu.

Recovery Mode

1. User must be holding the hand pulse sensor to use this feature. When the pulse value is displayed on the computer,
press on the RECOVERY button.

2. Hold on the hand pulse sensor until the TIME display nish the countdown from 60 seconds.

3. After the countdown ends, the result will be displayed on the monitor:

1.0 OUTSTANDING

1.0 < 1.9 EXCELLENT

2.0 < 2.9 GOOD

3.0 < 3.9 FAIR

4.0 < 5.9 BELOW AVERAGE

6.0 POOR

Body Fat Mode

1. After your workout, press on the BODY FAT button and hold on the handgrips.

2. After 8 seconds, the computer will display the BMI, FAT% and fat symbol.

3. Press on the BODY FAT button again to return to main menu.

B.M.I. (Body mass index) integrated

B.M.I. SCALE LOW LOW / MED MEDIUM MED / HIGH

Range < 20 20-24 24.1 - 26.5 > 26.5

BODY FAT

SYMBOL LOW (—) LOW / MED (+)

MEDIUM (p) MED / HIGH (¿)

MALE < 13% 13% - 25.9% 26% - 30% > 30%

FEMALE < 23% 23% - 35.9% 36% - 40% > 40%

www.yorkfitness.com

16

If you have a problem with your exercise equipment, before you do anything else please check that all the cables have
been connected correctly. Loose cables are very common and many problems can be solved by making sure the cables are
properly connected.

The following table details the most common problems and how to x them. If you still have a problem after going through the
troubleshooting guide please call your local YORK distributor for advice.

PROBLEM CAUSE CORRECTION

NO DISPLAY

No power Make sure power cord is plugged in properly

System halted

Unplug and re-plug the power cord to reset
the system

NO SPEED DISPLAY

Wires are damaged or not connected properly Verify all wires are connected properly

Speed sensor is too far from magnet Contact your local YORK distributor

PARTIAL DISPLAY The PA board is not connected properly

Unplug and re-plug the power cord

Verify all wires are connected properly

Disconnect and re-connect all cables

Contact your local YORK distributor

NO PULSE SIGNAL

Wires are damaged or not connected properly Verify all wires are connected properly

Too much hand movement Grip rmly

Palms too wet Dry palms

Hand Pulse Sensor is being gripped too tightly Grip using moderate pressure

User is wearing rings Remove all rings

ERROR CODE: E-1 Hands are not hold on handgrips tightly during BODY FAT test.

ERROR CODE: E-2 Check if cables are well connected or damaged.

ERROR CODE: E-4

Check the user’s age, height, weight gure setting when the test result is out of the range of
FAT% 5~50 and BMI 5~50%.

FOR YOUR OWN SAFETY, DO NOT OPEN PROTECTIVE CASING. IF ERROR PERSIST, PLEASE CONTACT YOUR LOCAL YORK
DISTRIBUTOR FOR ADVICE. KEEP THE EQUIPMENT OUT OF USE UNTIL IT IS REPAIRED.

If you are having problems with your heart rate reading, please note that some bres used in clothes eg) polyester, create
static electricity that may prevent a reliable heart rate reading. Mobile phones, TV’s, microwaves and other electrical
appliances that generate an electromagnetic eld may also interfere with heart rate measurement.

Troubleshooting

www.yorkfitness.comwww.yorkfitness.com

17

Notes

www.yorkfitness.com

18

Starting and Finishing Your Workout

Begin and end each workout with a Warm Up / Down session - a few minutes of stretching to help prevent strains, pulls and
cramps.

Correct Crosstraining Form

To start using the cross trainer, simply stand on the foot pedals with the front of your shoes close to the front edge of the
pedal cap. Place your hands at a comfortable position on the handlebars. Simply move your highest foot forward and follow
the natural path of the machine.

Start on a load level that is comfortable to familiarize yourself with the machine. Once you are comfortable, start adjusting
the load level to achieve the workout desired.

Forward and Reverse: The cross trainer can be used in the forward and reverse direction to vary the muscles that you
workout. This will also vary your workout helping you to stay motivated. To change directions, simply slow the pedals down
until they stop and switch directions.

Load Level Adjustment: The load level of cross trainer can be changed at any time during your workout. Adjusting your
load level will allow you to increase or decrease your intensity level.

Suggested Stretches

The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.

1. Hamstring Stretch

Sit with one leg extended.
Bring the sole of the
opposite foot toward you
and rest it against the inner
thigh of your extended leg.
Reach toward your toes
as far as possible. Hold
for 15 counts, then relax.
Repeat 3 times for each
leg. Stretches: Hamstrings,
lower back and groin.

2. Calf/Achilles Stretch

With one leg in front of the
other, reach forward and
place your hands against
a wall. Keep your back leg
straight and your back foot
at on the oor. Bend your
front leg, lean forward and
move your hips toward the
wall. Hold for 15 counts,
then relax. Repeat 3 times
for each leg. To cause
further stretching of the
achilles tendons, bend
your back leg as well.
Stretches: Calves, achilles
tendons and ankles.

3. Quadriceps Stretch

With one hand against a wall
for balance, reach back and
grasp one foot with your
other hand. Bring your heel
as close to your buttocks as
possible. Hold for 15 counts,
then relax. Repeat 3 times
for each leg. Stretches:
Quadriceps and hip muscles.

4. Inner Thigh Stretch

Sit with the soles of your
feet together and your
knees outward. Pull your
feet toward your groin area
as far as possible. Hold
for 15 counts, then relax.
Repeat 3 times. Stretches:
Quadriceps and hip
muscles.

Fitness Guide

www.yorkfitness.comwww.yorkfitness.com

19

How Long Should I Exercise For?

That really depends on your current level of tness. If you’re just starting out on a new exercise program, you should start
gradually and build up - do not try to do too much too quickly. 30 minutes, 3 times a week should be enough.

Don’t push yourself too hard - you should never feel exhausted during or following exercise.

Heart Rate Training

To get the most out of your new piece of tness equipment and see the best results from your training you should exercise
at the right level of eort, and that means listening to your heart! Working out to a target heart rate means you can direct
your workout to achieve dierent goals:

Good health - For those wishing to improve quality of life and general well being. Your sessions will need to be done at an
intensity of between 50 - 60% of your estimated maximum heart rate, should last about 30 minutes and can be done on
most days of the week.

Weight loss - To see a signicant reduction in body fat, your sessions must be a little more intense - between 60 and 70% of
your estimated maximum heart rate. These sessions can also be performed on most days of the week for up to 30 minutes.

Improving tness levels - These sessions should be performed at 70 - 80% of your estimated maximum heart rate and can
also involve bouts of interval training that would have your heart rate peaking for short times near your maximum heart
rate level. These are intense sessions and will require at least a 48 hour rest between sessions.

Calculating Your Target Heart Rate

First, you need to nd your estimated maximum heart rate using the formula “220 minus your age in years”. So, if you are 35
years old your estimated maximum heart rate is:

220 - 35 = 185 beats per minute (bpm)

Next, to calculate your target heart rate, simply multiply your estimated maximum heart rate (185bpm) by the applicable
percentage. So, if your goal is better health:

185 x 60% = 111bpm

NOTE: The important issue to remember with all estimated calculations is that they are just estimates - if you don’t feel
comfortable exercising at your target then reduce it to a level you are comfortable with.

Heart rate training requires you to monitor your heart rate throughout the workout. For this we recommend using a chest
strap (if your machine has a wireless receiver) or a heart rate monitor. For more information please get in touch using the
Contact Us details.

ALWAYS CONSULT YOUR DOCTOR BEFORE UNDERTAKING A NEW EXERCISE REGIME. IF YOU EXPERIENCE NAUSEA, DIZZINESS
OR OTHER ABNORMAL SYMPTOMS DURING EXERCISE, STOP AT ONCE AND CONSULT YOUR DOCTOR.

www.yorkfitness.com

20

A-1

A-2

N-3

B E

N-4

N-12

N-8

N-12

N-4

N-3

N-9

C

O

C-4

L

Z

I

N-4

N-12

N-3

N-9

N-4

N-7

N-10

N-4

N-10

N-7

N-1

N-2

M

K

N-5

N-6

N-4N-3

J

N-11

Exploded Drawing

www.yorkfitness.comwww.yorkfitness.com

21

G D F

R

E

TQH

C B A S J

O K

LM I

G-3

G-3

G-5

G-7

H-2

H-1

H-3

H-4

Q-6

Q-1

Q-10 Q-5

Q-3 Q-4

T-10

T-2

T-3

T-4

T-5

T-6

E-3

E-1

E-4

S-2 S-3

S-5

J-1

J-2

J-3

K-1

K-2

K-3

K-2

S-4

S-7

S-1

S-6

A-1

B-2

C-2

C-1

C-3

C-4

B-4

B-5

B-3

B-6

B-1

A-2

E-2

T-11

T-8

T-9 T- 1

T-7

Q-7 Q-8 Q-9

Q-2

G-4

G-6

G-2

G-10

G-6

G-8

G-14

G-13

G-12

G-9

G-11

G-15

G-3

D-1

D-3

D-2

D-10

F-3 F-4 F-1 F-2

F-5

R-2

R-9

R-4

R-1

R-5

R-6

R-8

R-7

R-3

D-9D-8D-7

D-6D-5

D-11

D-4

G-5

G-1

www.yorkfitness.com

22

YORK REF. REF. DESCRIPTION QT Y.

52069-1001 A COMPUTER SET 1

52069-1002 A-1 COMPUTER (SM-2789-67) 1

52069-1003 A-2 BOLT (M5*0.8*10L) 4

52069-1004 B FIXING BAR SET 1

52069-1005 B-1 FIXING BAR 1

52069-1006 B-2 FOAM 2

52069-1007 B-3 HANDLE PULSE SENSOR 2

52069-1008 B-4 HALF BALL CAP 2

52069-1009 B-5 SCREW (ST4*15L) 2

52069-1010 B-6 HANDLE PULSE CABLE 2

52069-1011 C HANDLEBAR POST SET 1

52069-1012 C-1 HANDLEBAR POST 1

52069-1013 C-2 UPPER COMPUTER CABLE 1

52069-1014 C-3 BUSHING (D19.15X(D25.6X32)XL(17+3)) 2

52069-1015 C-4 BO LT (M5*0.8*20L) 2

52069-1016 D MAIN FRAME SET 1

52069-1017 D-1 MAIN FRAME 1

52069-1018 D-2 BEEARING (#6003ZZ) 2

52069-1019 D-3 BUFFER 2

52069-1020 D-4 LOWER COMPUTER CABLE 1

52069-1021 D-5 ELEC TRIC CABLE 1

52069-1022 D-6 SENSOR CABLE 1

52069-1023 D-7 B OLT (M5X0.8X12L) 1

52069-1024 D-8 S CREW (ST4.2*1.4*15L) 4

52069-1025 D-9 MOTOR 1

52069-1026 D-10 TENSION CABLE 1

52069-1027 D-11 INNER TUBE 1

52069-1028 E HANDLEBAR SET

52069-1029 E-1 LEFT HANDLE BAR 1

52069-1030 E-2 RIGHT HANDLE BAR 1

52069-1031 E-3 F OAM 2

52069-1032 E-4 MUSHROOM CAP 2

52069-1033 F CRANK SET 2

52069-1034 F-1 ROUND COVER 1

52069-1035 F-2 CRANK 1

52069-1036 F-3 SID COVER 1

52069-1037 F-4 ANTI-LOOSEN NUT (M10*1.25*10T ) 1

52069-1038 F-5 SCREW (ST4X1.41X15L) 4

52069-1039 G SUPPORTING TUBE SET 2

52069-1040 G-1 SUPPORTING TUBE FOR MOVEABLE BAR 1

52069-1041 G-2 PEDAL SUPPORTING TUBE 1

52069-1042 G-3 BUSHING (D19.15X(D25.6X32)XL(17+3)) 6

52069-1043 G-4 FRONT PEDAL AXLE 1

52069-1044 G-5 WAVED WASHER (D26*D19.5*0.3T) 2

52069-1045 G-6 C-CLI P (D21.5XD17.5X1.2T) 4

52069-1046 G-7 SQUARE CAP 2

52069-1047 G-8 BUSHI NG (D29*D11.9*9T) 2

52069-1048 G-9 SCREW COVER (D30*17(M12)) 1

52069-1049 G-10 LADDER B OLT (M10*1.5*58L ) 1

52069-1050 G-11 FLAT WASHER ( D24*D13.5*2.5T) 1

52069-1051 G-12 FLAT WASHER ( D20*D11*2.0T) 1

52069-1052 G-13 SCREW COVER (D28*17(M10)) 1

YORK REF. REF. DESCRIPTION QT Y.

52069-1053 G-14 NYLON NUT (M 10*1.5*10T) 1

52069-1054 G-15 JOINT 1

52069-1055 H CHAIN COVER SET 1

52069-1056 H-1 LEFT CHAIN COVER 1

52069-1057 H-2 RIGHT CHAIN COVER 1

52069-1058 H-3 SCR EW (ST4X1.41X20L) 4

52069-1059 H-4 SCR EW (ST4.2X1.4X20L) 4

52069-1060 I PEDAL 2

52069-1061 J FRONT STABILIZER SET 1

52069-1062 J-1 FRONT STABILIZER 1

52069-1063 J-2 LEFT MOVEABLE CAP 1

52069-1064 J-3 RIGHT MOVEABLE CAP 1

52069-1065 K REAR STABILIZER SET 1

52069-1066 K-1 REAR STABILIZER 1

52069-1067 K-2 ADJUSTABLE CAP 2

52069-1068 K-3 SCREW ( ST4X1.41X10L) 2

52069-1069 L AXLE 1

52069-1070 M ADAPTOR 1

52069-1071 N SCREW SET 1

52069-1072 N-1 SQUARE NECK BOLT (M8X1.25X75L) 4

52069-1073 N-2 DO MED NUT (M8*1.25*15L) 4

52069-1074 N-3 CURVED WASHER (D22*D8.5*1.5T) 14

52069-1075 N-4 SPRING WASHER (D15.4*D8.2*2T) 16

52069-1076 N-5 FLAT WASHER (D14XD6.5X0.8T) 8

52069-1077 N-6 SCR EW (M6X15L) 8

52069-1078 N-7 SCREW CAP (D29*21(M8)) 2

52069-1079 N-8 WAVED WASH ER (D26*D19.5*0.3T ) 2

52069-1080 N-9 FLAT WASHER (D25XD8.5X2T) 2

52069-1081 N-10 BOLT (M8X1.25X25) 2

52069-1082 N-11 PROTECTIVE COVER 1

52069-1083 N-12 ALLEN BOLT (M8*1.25*20L ) 10

52069-1084 N-13 ALLEN SPANNER 1

52069-1085 N-14 SPANNER 2

52069-1086 O WATER BOTTLE HOLDER 1

52069-1087 P WATER BOTTLE (IS NOT INCLUDED) 0

52069-1088 Q IDLE WHEEL SET 1

52069-1089 Q-1 FIXING PLATE FOR IDLE WHEEL 1

52069-1090 Q-2 B OLT (M8X1.25X25L) 1

52069-1091 Q-3 IDLE WHEEL 1

52069-1092 Q-4 N YLON NUT (M10*1.5*10T) 1

52069-1093 Q-5 SPRING (D3*D17*65L) 1

52069-1094 Q-6 PLASTIC WASHER (D10*D24*0.4T) 1

52069-1095 Q-7 F LAT WASHER (D25XD8.5X2T) 1

52069-1096 Q-8 N UT (M8*1.25*6T) 1

52069-1097 Q-9 N YLON NUT (M8*1.25*8T) 1

52069-1098 Q-10 PLASTIC COVER 2

52069-1099 R CRANK AXLE SET 1

52069-1100 R-1 BELT WHEEL 1

52069-1101 R-2 CRANK AXLE 1

52069-1102 R-3 BOLT (M6*1.0*15L ) 4

52069-1103 R-4 NYLON NUT (M6X1.0X6T) 4

52069-1104 R-5 ROUND MAGNET 1

Part List

www.yorkfitness.comwww.yorkfitness.com

23

YORK REF. REF. DESCRIPTION QT Y.

52069-1105 R-6 C-CLIP (S-17(1T)) 2

52069-1106 R-7 WAVED WASHER (D17*D22*0.3T) 2

52069-1107 R-8 FLAT WASHE R (D23*D17.2*1.5T) 1

52069-1108 R-9 BELT (420(1067)L PJ5) 1

52069-1109 S FLYWHEEL SET 1

52069-1110 S-1 FLYWHEEL 1

52069-1111 S-2 BEARING (#6000ZZ) 2

52069-1112 S-3 FLYWHEEL AXLE 1

52069-1113 S-4 NY LON NUT (3/8"-26UNF*6.5T) 2

52069-1114 S-5 NU T (D9.5X5T(3/8"-26UNFX5T)) 2

52069-1115 S-6 NU T (D9.5X3T(3/8"-26UNFX3T)) 1

52069-1116 S-7 FIXING RING (D13*D10*1.9T) 1

52069-1117 T FIXING PLATE FOR MAGNET SET 1

52069-1118 T-1 FIXING PLATE FOR MAGNET 1

52069-1119 T-2 BOLT (M6*65L) 1

52069-1120 T-3 N UT (M6*1*6T) 1

52069-1121 T-4 SPRING (D1.0*42L) 1

52069-1122 T-5 NYLON WASHER (D6*D19*1.5T) 1

52069-1123 T-6 F LAT WASHER (D13* D6.5*1.0T) 1

52069-1124 T-7 NYLON NUT (M6*1*6T) 1

52069-1125 T-8 BOLT (M8*52L) 1

52069-1126 T-9 N YLON NUT (M8*1.25*8T) 1

52069-1127 T-10 MANGET 7

52069-1128 T-11 PLASTIC BAR 6

www.yorkfitness.com