www.yorkfitness.com.au
Owner’s Manual
C415 Upright Bike
Item #53101A
www.yorkfitness.com.au
Table of contents
Congratulation s on
purchasing your exercise
equipment from
You have chosen a high quality, safe and innovative
CONTENTS
Safety information 03
Customer support 04
Assembly Drawing 05
Exploded Drawing 06
piece of equipment as your training partner and we
are certain it will keep you motivated on the way to
achieving your personal fitness goals.
Parts List 07
Please take the time to read this owner’s manual as it
will help you to get the most out of your new exercise
equipment.
For more information visit www.yorkfitness.com.au
Assembly Steps 10
Console Instructions 15
Warranty 22
Protect the environment by not disposing
of this product or batteries with household
waste. Check your local authority for
recycling advice and facilities.
www.yorkfitness.com.au
Safety information
Please read this instruction manual before you begin
assembly. Great care has been taken to design these
instructions and following them will help you with
quicker assembly and minimize the risk of injury.
It is important that you keep these instructions for
future reference.
This list is not exhaustive - You are responsible for your
own safety
•
Always assemble and operate the equipment on a
level surface.
•
Ensure the equipment is stable before use.
•
Always ensure that the equipment has adequate
space on each side.
•
The safety level of this equipment can only be
maintained if it is regularly examined for wear and
tear.
•
Replace defective components immediately and keep
the equipment out of use until it is repaired.
•
Use only the adjustment setting as described in the
instructions. Always use the correct adjustment
pin / fixing.
•
Always check that any pins / fixings are tight and
secure before use and after adjustment.
•
Never leave any adjustment devices projecting from
the equipment.
•
Always consult your doctor before undertaking any
exercise program.
•
Always wear suitable clothing and footwear. (e.g.
tracksuit / shorts / training shoes)
•
Remove all personal jewellery before exercising.
•
Ensure you warm-up well before using the equipment
as this will help to prevent muscle strain.
•
After eating, allow 1-2 hours before exercising as this
will help to prevent muscle strain.
•
Never overload the equipment. (See maximum user
weight)
•
Never use the equipment in any other manner other
than the ways explained in these instructi ons and any
wall-chart supplied.
•
Injuries to health may result from incorrect or
excessive training.
•
Parents and others in charge of children should be
aware of their responsibility, because the natural play
instinct and the fondness of experimenting of children
can lead to situations and behaviour for which the
training equipment is not intended.
•
The equipment is under no circumstances suitable as
a children’s toy.
•
If children are allowed to use the equipment, their
mental and physical development and above all their
temperament should be taken into account. They
should be controlled and instructed in the correct use
of the equipment.
•
Children should not be allowed on or around the
equipment, especially when it is not in use.
•
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
•
This product is not suitable for therapeutic purposes.
•
This product has been tested for use in a home
environment and is warranted for In Home, personal,
family or household use.
•
Due to our continuous policy of product development,
York Fitness reserves the right to change
specifications without notice.
CAUTION The instructions must be followed carefully
in the assembly, use and maintenance of your
equipment. The warranty does not cover damage
due to negligence of the assembly, adjustment and
maintenance instructions des c ribed her ein.
Safety Standards
This equipment meets the requirements of the EU’s
EMC and Low Voltage directives (where applicable),
EN957 1 & 7 - CLASS HC. Therefore the equipment
carries the following marks:
Maximum user weight: 140kg
www.yorkfitness.com.au
Customer support
Should you require any assistance regarding this product please gather the
following information and then contact us using the details below:
•
Serial No. - This can be found on the sticker below, located as indicated.
•
Original purchase date
•
Place of purchase
•
Information about the plac e and con di ti ons o f use
•
Precise description of the issue / defect
IMPORTANT - Please retain your sales receipt. York Fitness Customer Care may
request proof of purchase to validate eligibility for warranty service. Warranty cover starts
from the date shown on the proof of purchase.
AUSTRALIA
The best way to contact us is via the website:
www.yorkfitness.com.au
Boyles Fitness Equipment Pty Ltd
13/160 Hartley Road,
Smeaton Grange, NSW 2567
Tel: 02 4648 0800
Product’s Name
Use only on a level surface
Not suitable for therapeutic purpose
Manufacturer:
Contact:
Product
Name:
Max
UserWeight:
Safety
Standards:
Electrical
Info:
BOYLES FITNESS EQUIPMENT
Unit 13, 160 Hartley Road, Smeaton Grange NSW 2567
C415 Upright Bike
140KG
EN957-1,7 Class HC
Adaptor 9V, 1300mA
SERIAL
NO: 53101A-
Serial Number
This product label is an example
only. I
t is not the
real product name and
serial number of the item
you have bought.
www.yorkfitness.com.au
Assembly Drawing
Exploded Drawing
www.yorkfitness.com.au
6
Parts List
No. Description QTY/ unit
1
Console
1
PCS
2
Screw M5X10L
4
PCS
3
Handlebar set
1
PCS
4 End cap 2
PCS
5 Screw M4X20L 2
PCS
6 Foam grip 2
PCS
7 Hand pulse sensor 2
PCS
8 Hand pulse sensor wire 2
PCS
9 Handlebar post 1
PCS
10 Console bracket cover, left 1
PCS
11 Console bracket cover, right 1
PCS
12
Screw M5X20L
4
PCS
13 Upper cable 1
PCS
14 Screw M8X16L
4 PCS
15 Semi washer φ8xφ19x2t
4 PCS
16 Seat post 1
PCS
17 Flat washer 1
PCS
18 Seat adjusting knob 1
PCS
19 Seat slider 1
PCS
20 End cap for sliding tube 2
PCS
21 Fixing screw bracket 1
PCS
22 Seat 1
PCS
23 Main frame 1
PCS
24 Handlebar post cover 1
PCS
25 Lower cable 1
PCS
26 Seat post knob 1
PCS
27 Seat post sleeve 1
PCS
28 Screw M4x10L 1
PCS
29 Sensor holder 1
PCS
30 Sensor wire 1
PCS
31 Flat washer φ5xφ10x1t
1 PCS
32 Screw M4x50L 3
PCS
33 Side cover, left 1
PCS
34 Bushing 1
PCS
35 Pedal, pair 1
SET
36 Screw M5x16L 4
PCS
37 Hex screw M8X12L 3
SET
38 Drive pulley 1
PCS
39 Axle 1
PCS
40 Bearing 6203
2 PCS
41 Wave washer
1 PCS
42 Flat washer φ5xφ10x1t
1 PCS
7
43
C-clip1 PCS
44
Drive belt
1
PCS
45
Side cover, right
1
PCS
46
Servo motor set
1
PCS
47
Nyloc screw M8X20L
2
PCS
48
Crank, left
1
PCS
49
Crank, right
1
PCS
50
DC wire
1
PCS
51
Flywheel set (51~63)
1
PCS
64
Magnet set (64~67)
1
SET
65
Spring washer
2
PCS
66
Hex screw M6X16L
2
PCS
67
Flat washer
2
PCS
68
Idler spring ODφ16xφ2.0
1
PCS
69
Idler
1
PCS
70
Nut M8
2
PCS
71
Bushing φ10xφ14x6mmL
1
PCS
72
Idler pulley w/bearing
1
PCS
73
Wave washer φ10.5xφ15x0.3t
2
PCS
74
Flat washer φ8.5xφ25x1t
1
PCS
75
Flat washer φ8.5xφ16x1t
1
PCS
76
Hex screw M8X20L
1
PCS
77
Front stabilizer
1
PCS
78
Screw M3x8
2
PCS
79
Transport wheel
2
PCS
80
Rear stabilizer
1
PCS
81
Screw 3/16"X 3/4"
2
PCS
82
End cap for rear stabilizer
2
PCS
83
Hex screw M8X75L
4
PCS
84
Spring washer φ8
4
PCS
85
Semi washer φ8xφ19x2t
4
PCS
86
Handlebar cover
1
PCS
87
T-knob screw M8X69L
1
PCS
88
Spring washer φ8xφ14x2T
1
PCS
89
Flat washer φ8*φ12*1T
1
PCS
9 %XVKLQJZUHQFK
1
PCS
www.yorkfitness.com.au
8
+H[ZUHQFK 1
PCS
+DUSRRQZUHQFK 1
PCS
6ZLWFKLQJSRZHU'&9P$ 1
PCS
:DWHU%RWWOH+ROGHU 1
PCS
www.yorkfitness.com.au
9
Tools and Parts
Q
�
Assembly Steps
Step 1.
1. Attach the front Stabilizer (77) to the main Frame (23) using screws (83), & washers (84+85).
2. Attach the rear Stabilizer (80) to the main Frame (23) using screws (83), & washers (84+85).
www.yorkfitness.com.au
10
11
www.yorkfitness.com.au
Step 2.
1. Assemble the two pedals (35-L, 35-R) onto cranks (48, 49) with a screw driver.
Screw the left pedal’s spindle counter-clockwise and the right pedal’s spindle clockwise.
Use a wrench (or screwdriver) to screw the two spindles completely
.
2. Assemble the seat (22) to the seat slider. The slider can be adjusted in different angles. Tighten
the two Nuts under the seat using a screwdriver. In addition, the slider can be adjusted in
horizontal level by loosening the knob.
3. Insert the seat post (16) into the main frame (23), and choose the desired position, then tighten the
knob (26). Be sure the knob is always tightened.
Remarks: When you have chosen a desired position, and tighten the seat post knob until you hear a
“click”.
12
www.yorkfitness.com.au
Step 3.
1. Put the cover (24) through handlebar post (9), and then connec t the upper cable (13) & lower cable
(25) as image display.
2. Insert the handlebar post (9) to the main frame, and fix with screws & washers (14, 15) by Allen
wrench and box spanner .
*
-
f
'
p
*
@
13
www.yorkfitness.com.au
Step 4.
1. Attach the handlebar (3) onto the handlebar post (9), fix with the cover (86) and lock tight with
washers and T-knob screw (87, 88, 89).
2. Pass the hand-pulse wire (8) through the hole to the top of handlebar post, as the image of drawing.
z
z
*
-
*
-
-
14
www.yorkfitness.com.au
Step 5.
1. Plug the upper cable (
13) and hand-pulse wire (8) with connectors on console.
2. Assemble the console (1) with 4 screws (2) by the box spanner.
3. Fix the console bracket covers (10, 11) with screws (12) to complete the assembly.
4. Install the water bottle holder (94) to the handlebar post using 2 screws (12).
5. Finally, plug in the switching power (93) to DC wire (50) and power supply for starting the
exercise.
5
M5X10L(4)
M520L(4)
M
www.yorkfitness.com.au
15
Console Instructional
As soon as the console is connected with power supply, an acoustic signal sounds and all of the
displays are shown on LCD for 2 seconds. Then wheel diameter will be shown briefly.
DISPLAY
Training Values
Display Range
Setting Range
TIME
0:00 ~ 99:59 min.
0:00 ~ 99:00 min.
SPEED
0.0 ~ 99.9 KM
/
DISTANCE
0.0 ~ 99.9 KM
0.0 ~ 99.0 KM
CALORIES
0 ~ 999 Cal.
0 ~ 990 Cal.
WATT
0~999 W
10~350 W
RPM
(Revolution/min.)
0 ~ 999
/
PULSE
30-230 BPM
0-30`230 BBPM
www.yorkfitness.com.au
16
BUTTON FUNCTIONS
Acoustic Signals
All settings made with the console are confirmed with an acoustic signal:
1 shot beep = setting confirmed
2 shot beeps =It is impossible to make any settings
Training Data
The console calculates and displays all values automatically according to user training status (see
table).
Take note:
* If only a “P” is shown instead of pulse value, it is impossible to measure the pulse. Grip the handle
where all four hand-pulse sensors are located. Moisten your palms first with a little water if necessary
* The display in the center field depends on the type of exercise that has been set.
The console provides a number of ways to vary the exercise session and make it more motivating.
The following exerci si ng modes ar e available:
-Manual Training (training without programs)
-Training with Programs ( there are 12 programs built-in, P01~P12)
-Training with your own program (User program)
-Training with the Heart Rate program (H.R.C)
-Training with set output value (WATT)
BUTTON FUNCTION
UP
- Increase resistance level
DOWN
- Decrease resistance level
Mode
-Confirm setting
-Select program
Reset
- Hold on pressi ng for 2 seco nds , console will reboot and start from user setting.
- Reset all values to zero during setting workout value or Stop mode.
Start/ Stop
- Start or Stop workout.
Recovery
- Track user Heart rate in recovery phase.
Body fat
- Measure user Body fat percentage and BMI(Body Mass Index).
17
www.yorkfitness.com.au
Starting exercise immediately (MANUAL)
Once a power connection has been established, the console will require you to create your own data.
Press UP and DOWN keys to set user data (for BODY FAT function), set Age, Gender, Height, Weight
in U1~U4, press MODE to confirm.
Then go to Workout selection mode.
MANUAL is flashing in matrix display with 1Hz.If you have previously selected a program or started
your workout, press RESET to return to the starting display.
-
Press START/STOP button to start workout immediately without entering further settings.
-
Press UP and DOWN keys to enter your personal settings:
-
The following fields will flash in turn
. TIME
. DISTANCE
. CALORIES
. PULSE
Use UP & DOWN to set values and confirm your selection by MODE button.
Press START/STOP to start workout.
As soon as one of the set value reach the preset Target, the icon will flash in the appropriate display
window (e.g. TIME) and several beeps sound.
- You can adjust the level of resistance on the pedals while exercising by pressing UP and DOWN keys.
The newly set value will be shown under the LOAD window (default value is Level 1).
- Press START/STOP to end exercising. All exercising value will remain.
- Press RESET to reverse to workout selection menu.
18
www.yorkfitness.com.au
Selecting a Program to do training (PROGRAM)
Once a power connection has been established, MANUAL is flashing in the display.
- Press UP and DOWN keys to go between MANUAL→PROGRAM→USER
PROGRAM→H.R.C.→WATT.
- Choose PROGRAM and press MODE to confirm. The programs are preset with 12 profiles. Press UP
and DOWN to select one from the 12 preset profiles. Set the desired session time and press
START/STOP to start workout.
- You can adjust the level of resistance on the pedals while exercising by pressing UP and DOWN
keys.
The newly set value will be shown under the LOAD window.
-
P
rogram explanation:
Interval programs P2- P3- P7- P12
Increasing resistance level programs P6- P9- P11
Increasing and decreasing resistance level programs P1- P4- P5- P8 -P10
The stored training programs are designed especially to enhance aerobic base fitness.
. As a beginner you should start with those programs slowly and set a low pedal resistance.
. You should only graduate to Interval programs once you have been training for several weeks.
- Press START/STOP to end exercising.
- Press RESET to reverse to workout selection menu.
User-defined profile (USER PROGRAM)
Here you can design your own profile with bars just like the preset program profiles.
-Press UP & DOWN to select USER PROGRAM and enter by pressing MODE. The first bar
will be
displayed.
-Press UP & DOWN to set resistance level and confirm by MODE button. The next bar will be
displayed.
-Continue this process until you have set up 20 bars. The max. resistance level is 32. To finish your
setting or quit setting, hold on pressing MODE button.
-Set the desired session time with UP & DOWN keys and press START/STOP to start workout.
-You can adjust the level of resistance on the pedals while exercising by pressing UP and DOWN keys.
19
www.yorkfitness.com.au
The newly set value will be shown under the LOAD window.
-Press START/STOP to end exercising.
-Press RESET to reverse to workout selection menu.
The console is designed for single workout usage only. Apart from User Profile U1-U4, no w
orkout
profile can be saved in all modes
Set program according to heart rate (H.R.C.)
In this program, the exercise bike reacts to your pulse as measured by the hand sensors.
This program allows you to exercise efficiently and safely within your required heart rate zone.
In addition, simple graphics also show you whether you need to increase or decrease your stress
Level. You can choose between:
HRC55 Here you are exercising in the very efficient range of 55%, ideal for beginners and for general
fat burning.
HRC75 This range of 75% of the maximum pulse rate is suitable for experienced users and athletes.
HRC90 The anaerobic range of 90% of the maximum pulse rate is only suitable for competitive athletes
and short sprint exercises.
TAG The console uses your Age to calculate a target pulse rate, which you can change as
you choose. Never select a target pulse that is higher than your age-determined maximum
pulse rate.
-Press UP & DOWN to select H.R.C. and enter by pressing MODE. Choose HRC55-->HRC75-->
HRC90->TARGET. With HRC55,HRC75,HRC90, the max. Heart rate will be calculated by the
console automatically.
-With the TARGET program, the preset value 100 will be shown. Press UP & DOWN buttons to set a
value between 30~230 and confirm by MODE. The program has been saved.
-Set the desired session time with UP & DOWN buttons and press START/STOP to start workout.
For this program, it is necessary to keep your hands on the sensor grips while exercising so that
console can detect and display your heart rate value.
20
www.yorkfitness.com.au
Program sequence:
The console sets a pedal resistance that keeps you exercising constantly w ithin your target pulse
rate.
If you are exercising and go below your preset pulse rate, the pedal resistance will automatically rise
by
one stress level ev ery 30 seconds.
If you are exercising and go above your preset pulse rate, the pedal resistance will automatically
decrease by one stress level every 15 seconds. If you have already reached the lowest level “1” and
your pulse rate is still higher than your preset value, then after about 30 seconds an acoustic signal
will alarm and the console program will end automatically.
Exercising with set output values (WATT)
Here you can enter a constant output value. The console automatically adjusts the pedal resistance to
your speed so that your output remains constant.
-Press UP & DOWN to select WATT and enter by pressing MODE. Press UP & DOWN to set desired
session output value (default value: 120).
-Set the desired session time with UP & DOWN key and press START/STOP to start workout.
-You can adjust WATT level while exercising by pressing UP and DOWN keys. The newly set value will
be shown under the WATT window.
-Press START/STOP to end exercising.
-Press RESET to reverse to workout selection menu.
Measuring your pulse with the hand sensors
The hand sensors are not medical products, but rather exercising tools designed for the approximate
measurement and displaying of the pulse rate when exercising with the exercise bike.
Recovery phase
It is recommended to end an intensive exercise session with a recovery phase. During this phas e
you should be able to relax and pedal without strong resistance until your pulse slows close to its
usual rate.
-Press RECOVERY button and grip the hand sensors again. Then only TIME is showing and counting
down from 60 seconds to 0, all other functions are not available.
Once the 60 seconds recovery phase is over, an evaluation of the achieved heart rate will be shown.
21
-If your heart rate is still very high after 60s (F is between 4 and 6), you could restart the recovery
program to gradually sl ow your heart rate further.
Body Fat measurement
Here you can measure your Body Fat percentage and BMI.
(The test should be done when there is no pedalling)
-Press Body Fat button to start measurement.
-Hold both hands on sensor
grips. When there is a HR (heart rate) signal detected for 8 seconds,
console will show your BM, FAT% and fat symbol.
-After measurement, press Body Fat key again to go back program selection page
<REFERENCE>
B.M.I. (Body mass index) integrated
BODY FAT:
SYMBOL
—
＋
▲
◆
FAT%
SEX
LOW
LOW/MED
MEDIUM
MED/HIGH
MALE
<13%
13%-25.9%
26%-30%
>30%
FEMALE
<23%
23%-35.9%
36%-40%
>40%
CAUTION
* This
console requires 9V, 500mA or 9V, 1000mA power supply.
* For 4 minutes if no pedalling or pulse input, console will switch to idle mode. All settings and
program data will be saved until the session is continued. Press any key to wake up the console.
* When console works abnormally, please unglug the adaptor and plug in again.
Attention! All preset data will be lost when you unplug the power (adaptor) from the "machine"
B.M.I
SCALE
LOW
LOW/MED
MEDIUM
MED/HIGH
RANGE
<20
20-24
24.1-26.5
>26.5
WARRANTY, SAFETY AND ASSEMBLY
INFORMA TION YRK53101A– YORK C415
IMPORTANT
Please read and retain this manual as it will assist with identification for parts and service.
-----------------------------------------------------------------------------------------------------------BOYLES FITNESS warrants their Bike to be free from defects in material and
workmanship under normal use and service conditions.
The various components of the Bike are warranted against defects and workmanship for
the time periods specified as follows:
YRK53101A – YORK C415
Domestic use
Lifetime frame & 1 year on all other parts.
All warranty coverage extends only to the original retail purchaser from the date of
purchase. BOYLES FITNESS’ obligation under this Warranty is limited to replacing or
repairing, at BOYLES’ option, the product or parts therein. Any enquiries relating to
warranties or spare parts must be directed to Service 07 3272 7010 .
For efficient processing of your enquiry please have relevant date of purchase, retailer
name you purchased the item from and the brand on the product. This warranty does not
extend to any damage to a product caused by abuse, improper or abnormal usage (as
detailed in this instruction manual), or repairs not provided by BOYLES. Nor does this
warranty extend to products used for commercial or rental purposes. This warranty does
not cover ordinary wear, tear and weathering, failure to follow directions, improper
installation, improper maintenance or acts of God (such as damage caused by storms,
lightning and by snow or ice). No other Warranty beyond that specifically set forth above is
authorised by BOYLES.
Our sales and service centre has been set up to provide assembly assistance, replacement
parts and accessories, and to efficiently handle all warranty related matters.
Phone 07 3272 7010
Hours 9:00am – 4:00pm Mon-Fri (excluding public holidays),
Email spares@boylesfitness.com.au
Website
www.boylesfitness.com.au
22
www.yorkfitness.com.au
23
BFE Warranty Policy – November 1
st
2013
1.
When purchased from an authorised BFE distributor the BFE warranty shall guarantee that all framework and
components of your product are free from faulty manufacture. All faulty framework and components will be
repaired or replaced as set out in this policy. All warranties in this policy apply to INDOOR HOME/DOMESTIC
USE ONLY.
2.
These warranties do not apply to products used in commercial use applications.
3.
Warranty DOES NOT cover normal wear & tear and excludes faults due to misuse, abuse, incorrect assembly
or lack of general maintenance.
4.
Warranty is applicable to products sold and placed within Australia only.
5.
IMPORTANT. Most of BFE products are pretested and we have inspectors checking all products prior to
shipment. The number one reason for a fault is due to INCORRECT ASSEMBLY.
If you do have problems please go back to the start and double check your assembly and pay special attention
to all WIRING connections. If you have accidently cut or damaged the wiring please let us know and we will
be happy to send you a new set at no-charge.
If you have done this and are confident you have double checked your assembly and are still having problems please
email our service department at spares@boylesfitness.com.au including your best contact details ,proof of purchase,
serial number and a brief explanation of what is wrong.
Emailing is the quickest and most reliable way to get your service request processed. Once we have your details we will
either call or email you back with the next steps. The quickest way, once we determine the problem and send you a
replacement part, is that we can talk you through over the phone on how to fit it.
If it is deemed by our service tech that it is too difficult, we can arrange (where available) a service technician.
NOTE. If we arrange for a service technician ( where applicab le) and i t is fou nd t hat it is no t a m anufac tures f ault and
found to be an assembly issue , normal wear and tear, transport damage or misuse then there will be a call out fee of
$140 depending on location. (Surcharge applies for non-metro areas)
WARRANTY TE R MS- W arranty com m ences f rom the date of purchase f rom the retail stor e. Warranty onl y a ppl ies to
the original purchaser and is NON transferable. Warranty is void if the serial number of the product has been removed
or tampered with.
Warranty does not apply to defects, faults or f ailures due to:
(a)
Defects caused during assembly or failure to assemble to the assembly manual provided. Assembly errors include
but are not limited to damaged wiring harness, stripped crank arms and or pedals and bolts used in the wrong locations.
(b)
Lack of general maintenance and or failure to service or maintain the equipment in accordance with the user manual
specifications and recommendations.
(c)
Power Surges. The computers, control boards and motors are very sensitive to power fluctuations. You must use a
surge protector on all items that plug into your mains power otherwise your electronics will not be covered by this
warranty. You can purchase these from numerous retailers.
(d)
User negligence, abnormal or excessive use, misuse, abuse or transport damage.
(e)
Repairs, alterations or modifications by NON BFE authorised service technician.
(f)
Accident, fire, flood or malicious damage by third person.
(g)
Ordinary wear and tear.
(h)
Failure to keep the product in a clean, dry environment causing rust. You should wipe off any sweat and moisture after
each training session.
(i)
Any products sold or placed in an application or the incorrect environment that is not recommended by BFE or as not
stipulated in the owner’s manual such as a commercial / rental environment will void the warranty set forth by BFE
BFE will have the option to repair or replace any product which requires attention under the warranty.
NOTE: Lifetime refers to the warranty coverage of the units expected service life. NOT the lifetime of the purchaser.
Servicing/Spare Parts - As with any mechanical equipment general maintenance should be performed on a regular basis
by an authorised retailer or service technician. This will ensure longevity of the product and ensure that it is kept working
in optimum condition. Failure to properly maintain your equipment may lead to safety issues and may also void the warranty.
You should only use genuine BFE replacement parts otherwise the warranty will be void.
Freight Costs:
The cost of freighting the replacement part under warranty to the customer shall be free of charge. Your requirement is to
return the faulty part via the pre-paid postal service which we will supply.
24
Returned Goods:
The unauthorised return of parts or product shall be refused and placed in the hands of the carrier at the cost of the shipper.
Return authorisations can be obtained from BFE head office only.
Service Department hours: Monday to Friday between 9.00am and 4pm
Service Phone Number: 07 3272 7010
PLEASE NOTE: that Authorised service technicians do not reside in all areas of this vast country. If you live beyond the
reasonable service area of a metropolitan area, BFE may not be able to support the labour portion of the product warranty.
Alternatively you can return (at your cost) your product to the closest BFE repair centre, where it will be fixed at no charge
under the warranty period.
Metropolitan Area- defined as no more that 50km from G.P.O in all capital cities.
Disclaimer:
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a ‘Major failure’ and for compensation for any other Reasonable foreseeable loss or damage.
You are also entitled to have goods repaired or replaced if the goods fail to be of an acceptable quality and the failure
does not amount to a major failure.
BFE does not assume , nor authorise any representative or other person to make or assume for BFE , any warranties
whatsoever, whether expressed or implied, in , in connection with the sale, service, or shipment of our products.
BFE reserve the right to make changes and improvements in our products and specifications without incurring any
obligation to similarly alter products previously purchased.
This warranty operates in addition to other rights and remedies available to consumer’s rights under the Australian
Consumer Law.
www.yorkfitness.com.au
Loading...