Owner’s Manual
Aspire Exercise Cycle
53070
V1.0 10OCT2012
www.yorkfitness.com
www.yorkfitness.com
2
Table of contents
Congratulations on
purchasing your exercise
equipment from
You have chosen a high quality, safe and innovative
piece of equipment as your training partner and we
are certain it will keep you motivated on the way to
achieving your personal tness goals.
Please take the time to read this owner’s manual as it
will help you to get the most out of your new exercise
equipment.
For more information visit www.yorktness.com
Contents
Safety information 03
Customer support 04
Care & Maintenance 05
Assembly instructions 05
Operational instructions 12
Troubleshooting 17
Fitness guide 18
Exploded drawing 20
Part list 21
Protect the environment by not
disposing of this product or batteries
with household waste. Check your
local authority for recycling advice and
facilities.
www.yorkfitness.comwww.yorkfitness.com
3
Safety information
Please read this instruction manual before you begin
assembly. Great care has been taken to design these
instructions and following them will help you with
quicker assembly and minimize the risk of injury.
It is important that you keep these instructions for
future reference.
This list is not exhaustive - You are responsible for your
own safety!
• Always assemble and operate the equipment on a
level surface.
• Ensure the equipment is stable before use.
• Always ensure that the equipment has adequate
space on each side.
• Ensure that the seat height is adjusted correctly.
You should be stable and balanced while on the
saddle.
• Adjust the seat height to ensure that you
have a good downward pedal stroke without
overstretching, don’t compromise your balance.
• Try to ensure that your back is straight while
exercising, especially for long periods.
• The safety level of this equipment can only be
maintained if it is regularly examined for wear and tear.
• Replace defective components immediately and
keep the equipment out of use until it is repaired.
• Use only the adjustment setting as described in the
instructions. Always use the correct adjustment pin
/ xing.
• Always check that any pins / xings are tight and
secure before use and after adjustment.
• Never leave any adjustment devices projecting from
the equipment.
• Always consult your doctor before undertaking any
exercise program.
• Always wear suitable clothing and footwear. (e.g.
tracksuit / shorts / training shoes)
• Remove all personal jewelry before exercising.
• Ensure you warm-up well before using the
equipment as this will help to prevent muscle strain.
• After eating, allow 1-2 hours before exercising as
this will help to prevent muscle strain.
• Never overload the equipment. (See maximum user
weight)
• Never use the equipment in any other manner other
than the ways explained in these instructions and
any wall-chart supplied.
• Injuries to health may result from incorrect or
excessive training.
• Parents and others in charge of children should be
aware of their responsibility, because the natural
play instinct and the fondness of experimenting
of children can lead to situations and behavior for
which the training equipment is not intended.
• If children are allowed to use the equipment, their
mental and physical development and above all
their temperament should be taken into account.
They should be controlled and instructed in the
correct use of the equipment.
• The equipment is under no circumstances suitable
as a children’s toy.
• Children should not be allowed on or around the
equipment, especially when it is not in use.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• This product is not suitable for therapeutic purposes.
• This product has an integrated speed independent
braking system without a constant power mode
that is governed by magnetic resistance.
• This product has been tested for use in a home
environment and is warranted for In Home,
personal, family or household use.
• Due to our continuous policy of product
development, York Fitness reserves the right to
change specications without notice.
CAUTION! The instructions must be followed carefully
in the assembly, use and maintenance of your
equipment. The warranty does not cover damage
due to negligence of the assembly, adjustment and
maintenance instructions described herein.
Maximum user weight: 120kg
Safety Standards
This equipment meets the requirements of the EU’s
EMC and Low Voltage directives (where applicable),
EN957 1 & 5 - CLASS HB. Therefore the equipment
carries the following marks:
www.yorkfitness.com
4
Customer support
Should you require any assistance regarding this product please gather
the following information and then contact us using the details below:
• Serial No. - This can be found on the sticker below, located as indicated.
• Original purchase date
• Place of purchase
• Information about the place and conditions of use
• Precise description of the issue / defect
Use only on a level surface
Not suitable for therapeutic purpose
Manufacturer: YORK BARBELL
Contact: www.yorktness.com
Product Name: YORK ASPIRE EXERCISE CYCLE
Max User Weight: 130KG
Safety Standards: EN957 Part 1 & 5 - Class HB
Electrical info: Adaptor 9V, 500mA
SERIAL NO:
53070-
Product’s Name
Serial Number
This product label is an example only, it is not the
real product name and serial number of the item
you have bought.
Underside of the
main body.
IMPORTANT!! - Please retain your sales receipt, York Fitness Customer Care may request proof of purchase to
validate eligibility for warranty service. Warranty cover starts from the date shown on the proof of purchase.
ENGLAND
The best way to contact us is via the website:
www.yorktness.com
York Barbell UK Ltd.
York Way, Daventry, England, NN11 4YB
Tel: 0844 225 3112
AUSTRALIA
The best way to contact us is via the website:
www.yorktness.com.au
York Fitness Australia
1/2 Swaffham Rd, Minto, PO Box 5130, NSW 2566
Tel: 1800 730 149
www.yorkfitness.comwww.yorkfitness.com
5
Care & Maintenance
• This equipment should not be placed outdoors, in a garage or an outbuilding. Keep the equipment in a dry
place with as little temperature variation as possible.
• We recommend placing a mat beneath the equipment to protect both the equipment and your ooring.
• Always place the equipment in a dry environment.
• Use a warm, damp cloth to keep the product clean.
• No wet cleaning of electrical components. Unplug before any care and maintenance.
• The safety level of the equipment can be maintained only if it is regularly examined for damage and wear. This
includes any ropes, pulleys, nuts, bolts, moving parts, bushes, chains, wheels, bearings & connection points etc.
• Ensure that you inspect the product regularly - at least once a week is recommended.
• Ensure that all xings are tight before use.
• Always replace damaged / worn components with original parts from the manufacturer.
PREPARE YOUR WORK AREA - It is important you assemble the product in a clean and uncluttered space.
WORK WITH A FRIEND - We recommend you have someone assist you with the assembly as some of the
components are quite heavy.
OPEN THE CARTON - Check any warnings on the carton and make sure you have it the right way up.
UNPACK THE CARTON - Remove all the parts and lay them out on the oor.
Make sure you have the following parts:
N-2 (4pcs)
D15.4 x D8.2 x 2T
Step - 1
Step - 3
Fixing Blister Pack
N-3 (4pcs)
D16 x D8.2 x 1.5T
N-7 (1pc)
N-6 (1pcs)
N-5 (6pcs)
M8 x 1.25 x 20L
N-2 (6pcs)
D15.4 x D8.2 x 2T
N-1 (4pcs)
M8 x 1.25 x 50L
N-4 (6pcs)
D22 x D8.5 x 1.5T
www.yorkfitness.com
6
Assembly instructions
Make sure you have the following parts:
Z (1pc)
C (1pc)
I (1pc)
B (1 set)
L (1pc)
A (1pc)
O (1pc)
P (1 set)
N (1 set)
D (1pc)
J (1pc)
www.yorkfitness.comwww.yorkfitness.com
7
STEP 1
N-1 (4pcs)
N-2 (4pcs)
N-3 (4pcs)
N-1
N-2
N-3
J-2
Z
I
J
www.yorkfitness.com
8
Assembly instructions
STEP 2
L-3 (3pcs)
L-2 (3pcs)
L-1
a
b
up
down
L-1
L-2
L-2
L-3
D
L-3
D
www.yorkfitness.comwww.yorkfitness.com
9
STEP 3
a
b
B
N-4
C-2
C
N-2
N-2
N-5
N-4
E-9
N-5
N-5 (6pcs)
N-2 (6pcs)
N-4 (6pcs)
www.yorkfitness.com
10
Assembly instructions
STEP 4
A-2 (4pcs)
a
A
O
A
A-2
C-2
B-4
P-1
C-2
B-4
www.yorkfitness.comwww.yorkfitness.com
11
Final Check
Your exercise cycle is now assembled.
Please make the following nal checks:
Make sure all screws / bolts are tightened.
Make sure the equipment is on a at, level surface.
Input Power
Plug in the adaptor to the equipment then the
computer will produce a beep sound and turn
on the computer at the Manual mode.
www.yorkfitness.com
12
Operational instructions
Console:
Key Function:
KEY DESCRIPTION
Up • Increase resistance level
• Setting selection.
Down • Decrease resistance level
• Setting selection.
Mode • Conrm setting or selection.
Reset • Press and hold for 2 seconds, computer will reboot and start from
user setting.
• Go back to main menu during presetting workout value or stop mode.
Start/ Stop • Start or Stop workout.
Recovery • Test heart rate recovery status.
www.yorkfitness.comwww.yorkfitness.com
13
Display Function:
DISPLAY DESCRIPTION
TIME • Workout time displayed during exercise.
• Range 0:00 ~ 99:59
SPEED • Workout speed displayed during exercise.
• Range 0.0 ~ 99.9
DISTANCE • Workout distance displayed during exercise.
• Range 0.0 ~ 99.9
CALORIES • Burned calories during workout display.
• Range 0 ~ 999
PULSE • Pulse bpm displayed during exercise.
• Pulse alarm when over preset target pulse.
RPM • Rotation per minute
• Range 0 ~ 999
WATT • Workout power consumption
• In Watt Program mode, computer will remain preset watt value (setting
range 0~350)
MANUAL • Manual mode workout.
PROGRAM • 12 PROGRAM selection.
USER • User creates resistance level prole.
H.R.C. • Target HR training mode.
POWER ON
Plug in power supply, computer will power on and display all segments on LCD for 2 seconds. After 4 minutes
without pedaling or pulse input, console will enter into power saving mode.
Press any key to wake the console up.
www.yorkfitness.com
14
Manual Mode
Press START in main menu to start workout in manual mode.
1. Press UP or DOWN to select workout program, choose Manual and press Mode to enter.
2. Press UP or DOWN to preset TIME, DISTANCE, CALORIES, PULSE and press MODE to conrm.
3. Press START/STOP keys to start workout. Press UP or DOWN to adjust load level.
4. Press START/STOP keys to pause workout. Press RESET to go back to main menu.
Program Mode
1. Press UP or DOWN to select workout program, choose the Program and press Mode to enter. (Total Program = 12)
2. Press UP or DOWN to preset TIME.
3. Press START/STOP key to start workout. Press UP or DOWN to adjust load level.
4. Press START/STOP key to pause workout. Press RESET to go back to main menu.
User Program Mode
1. Press UP or DOWN to select workout program, choose User and press Mode to enter.
2. Press UP or DOWN to set load level of each column, and press MODE to next one. (Total column = 20)
3. Press and hold MODE to nish or quit setting.
4. Press UP or DOWN to preset workout TIME.
5. Press START/STOP key to start workout. Press UP or DOWN to adjust load level.
6. Press START/STOP key to pause workout. Press RESET to go back to main menu.
H.R.C. mode
1. Press UP or DOWN to select workout program, choose H.R.C. and press Mode to enter.
2. Press UP or DOWN to set up age (default: 25) (setting range: 1~99)
3. Press UP or Down to select 55%.75%.90% or TAG (TARGET H.R.) (default: 100).
4. Press UP or DOWN to preset workout TIME.
5. Press START/STOP key to start or stop workout. Press RESET to go back to main menu.
Operational instructions
www.yorkfitness.comwww.yorkfitness.com
15
WATT Mode
1. Press UP or DOWN to select workout program, choose WATT and press Mode to enter.
2. Press UP or DOWN to preset WATT target. (default: 120)
3. Press UP or DOWN to preset TIME.
4. Press START/STOP key to start workout. Press UP or DOWN to adjust Watt level.
5. Press START/STOP key to pause workout. Press RESET to reverse to main menu.
Recovery
1. User must be holding the handgrips. When the pulse value is displayed on the computer, press the
RECOVERY key.
2. TIME shows “0:60” (seconds) and counts down.
Computer will show F1 to F6 after count down to 0 to test heart rate recovery status.
1.0 OUTSTANDING
1.0 < 1.9 EXCELLENT
2.0 < 2.9 GOOD
3.0 < 3.9 FAIR
4.0 < 5.9 BELOW AVERAGE
6.0 POOR
www.yorkfitness.com
16
Operational instructions
Hand Pulse Sensors
This exercise cycle is tted with 2 hand pulse sensors. To
obtain a pulse reading you must have both your left and right
hands on the sensors at the same time. Do not grip the hand
sensors too tight and allow the computer a few seconds to
display the reading.
Hand Pulse Sensor
Adjusting The Resistance
This exercise cycle features a speed independent braking
(resistance) system. The resistance is controlled by a
magnet, which is moved closer or further away from the
ywheel - the closer the magnet is to the ywheel the higher
the resistance.
Resistance Level
Adjust the seat
1. Unscrew the hand wheel.
2. Adjust the seat up / down or forward / backward to your
requirements.
3. Re-screw the hand wheel - make sure it is screwed in
tightly.
4. The basic rule for getting the seat height right is that as the
pedal reaches its lowest point, the leg is almost straight.
Note: Do not pull the seat out too far - the maximum is
indicated with a piece of tape on the seat post.
www.yorkfitness.comwww.yorkfitness.com
17
If you have a problem with your exercise equipment, before you do anything else please check that all the cables
have been connected correctly. Loose cables are very common and many problems can be solved by making sure
the cables are properly connected.
The following table details the most common problems and how to x them. If you still have a problem after going
through the troubleshooting guide please call your local YORK distributor for advice.
PROBLEM CAUSE CORRECTION
NO DISPLAY NO DISPLAY - Check the cables are all connected correctly.
NO SPEED DISPLAY If there is no signal when you pedal, please check if the cable is well connected.
NO PULSE SIGNAL
Wires are damaged or not connected
properly
Verify all wires are connected properly
Too much hand movement Keep hand stills
Palms too wet Dry palms
Hand Pulse Sensor is being gripped too
tightly
Grip using moderate pressure
User is wearing rings Remove all rings
DISPLAY ERROR: E-2 Check if cables are well connected or damaged.
FOR YOUR OWN SAFETY, DO NOT OPEN PROTECTIVE CASING. IF ERROR PERSISTS, PLEASE CONTACT
YOUR LOCAL YORK DISTRIBUTOR FOR ADVICE. KEEP THE EQUIPMENT OUT OF USE UNTIL IT IS REPAIRED.
If you are having problems with your heart rate reading, please note that some bres used in clothes eg) polyester,
create static electricity that may prevent a reliable heart rate reading. Mobile phones, TV’s, microwaves and other
electrical appliances that generate an electromagnetic eld may also interfere with heart rate measurement.
Troubleshooting
www.yorkfitness.com
18
Fitness guide
Starting and Finishing Your Workout
Begin and end each workout with a Warm Up / Down session - a few minutes of stretching to help prevent strains,
pulls and cramps.
Correct Cycling Form
• Sit on the cycle, with your feet on the pedals and inside the pedal straps.
• Ensure that the seat height is adjusted correctly - you should be stable and balanced whilst on the saddle.
The basic rule for getting the seat height right is that as the pedal reaches its lowest point, the leg is almost
straight.
• Try to ensure that your back is straight whilst exercising, especially for long periods.
Suggested Stretches
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Hamstring Stretch
Sit with one leg
extended. Bring the
sole of the opposite
foot toward you and
rest it against the inner
thigh of your extended
leg. Reach toward your
toes as far as possible.
Hold for 15 counts, then
relax. Repeat 3 times
for each leg. Stretches:
Hamstrings, lower back
and groin.
2. Calf/Achilles Stretch
With one leg in front of
the other, reach forward
and place your hands
against a wall. Keep your
back leg straight and
your back foot at on the
oor. Bend your front leg,
lean forward and move
your hips toward the
wall. Hold for 15 counts,
then relax. Repeat 3
times for each leg. To
cause further stretching
of the achilles tendons,
bend your back leg as
well. Stretches: Calves,
achilles tendons and
ankles.
3. Quadriceps Stretch
With one hand against a
wall for balance, reach
back and grasp one foot
with your other hand. Bring
your heel as close to your
buttocks as possible. Hold
for 15 counts, then relax.
Repeat 3 times for each
leg. Stretches: Quadriceps
and hip muscles.
4. Inner Thigh Stretch
Sit with the soles of your
feet together and your
knees outward. Pull your
feet toward your groin
area as far as possible.
Hold for 15 counts, then
relax. Repeat 3 times.
Stretches: Quadriceps
and hip muscles.
www.yorkfitness.comwww.yorkfitness.com
19
How Long Should I Exercise For?
That really depends on your current level of tness. If you’re just starting out on a new exercise program, you should
start gradually and build up - do not try to do too much too quickly. 30 minutes, 3 times a week should be enough.
Don’t push yourself too hard - you should never feel exhausted during or following exercise.
Heart Rate Training
To get the most out of your new piece of tness equipment and see the best results from your training you should
exercise at the right level of effort, and that means listening to your heart! Working out to a target heart rate means
you can direct your workout to achieve different goals:
Good health - For those wishing to improve quality of life and general well being. Your sessions will need to be
done at an intensity of between 50 - 60% of your estimated maximum heart rate, should last about 30 minutes and
can be done on most days of the week.
Weight loss - To see a signicant reduction in body fat, your sessions must be a little more intense - between 60
and 70% of your estimated maximum heart rate. These sessions can also be performed on most days of the week
for up to 30 minutes.
Improving tness levels - These sessions should be performed at 70 - 80% of your estimated maximum heart rate
and can also involve bouts of interval training that would have your heart rate peaking for short times near your
maximum heart rate level. These are intense sessions and will require at least a 48 hour rest between sessions.
Calculating Your Target Heart Rate
First, you need to nd your estimated maximum heart rate using the formula “220 minus your age in years”. So, if
you are 35 years old your estimated maximum heart rate is:
220 - 35 = 185 beats per minute (bpm)
Next, to calculate your target heart rate, simply multiply your estimated maximum heart rate (185bpm) by the
applicable percentage. So, if your goal is better health:
185 x 60% = 111bpm
NOTE: The important issue to remember with all estimated calculations is that they are just estimates - if you don’t
feel comfortable exercising at your target then reduce it to a level you are comfortable with.
Heart rate training requires you to monitor your heart rate throughout the workout. For this we recommend using
a chest strap (if your machine has a wireless receiver) or a heart rate monitor. For more information please get in
touch using the Contact Us details.
Always consult your doctor before undertaking a new exercise regime. If you experience nausea, dizziness or other
abnormal symptoms during exercise, stop at once and consult your doctor.
www.yorkfitness.com
20
A-1
A
I
P
B C E
O G D M
J K L
F H
I-4
P-1
B-5
B-4
B-3
B-1
B-2
C-1
C-2
P-2
G-2
G-3
G-7
M-5 M-6
M-1
M-4
M-2
M-3
G-6
G-8
G-9
G-5
G-4
I-3
I-2
I-1
J-2
J-1
J-3
K-5
K-1
K-2
K-4
L-3
L-2
L-1
K-3
K-7
K-6
K-8
K-9
F-1
F-2
F-3
F-4
H-5
H-9
H-8
H-6
H-7H-4
H-2
H-3 H-1H-12
K-10
K-11
K-12
H-11
E-18
E-15
E-14
E-13E-9
E-16
E-17
G-10
G-11
G-1
E-19
E-6E-4
E-2
E-3
E-5
E-7
E-8
E-12
E-11
E-10
E-1
H-10
A-2
Exploded drawing
www.yorkfitness.comwww.yorkfitness.com
21
Part list
YORK REF. REF. DESCRIPTION QTY.
53070-1 A COMPUTER SET 1
53070-2 A-1 COMPUTER 1
53070-3 A-2 BOLT 4
53070-4 B HANDLEBAR SET 1
53070-5 B-1 HANDELBAR 1
53070-6 B-2 ROUND CAP 2
53070-7 B-3 HANDLE PULSE 2
53070-8 B-4 HANDLE PULSE CABLE 2
53070-9 B-5 FOAM 2
53070-10 C HANDLEBAR POST SET 1
53070-11 C-1 HANDLEBAR POST 1
53070-12 C-2 UPPER COMPUTER CABLE 1
53070-13 D SEAT POST 1
53070-14 E MAIN FRAME SET 1
53070-15 E-1 MAIN FRAME 1
53070-16 E-2 FIXED NUT 2
53070-17 E-3 FIXING PLATE 1
53070-18 E-4 FIXING BOLT(LEFT) 1
53070-19 E-5 BALLBEARING 2
53070-20 E-6 BEARING COVER 2
53070-21 E-7 FIXING PLATE 1
53070-22 E-8 FIXING BOLT(RIGHT) 1
53070-23 E-9 LOWER COMPUTER CABLE 1
53070-24 E-10 KNOB 1
53070-25 E-11 INNER TUBE 1
53070-26 E-12 INNER TUBE 1
53070-27 E-13 ELECTRIC CABLE 1
53070-28 E-14 SENSOR CABLE 1
53070-29 E-15 BOLT 1
53070-30 E-16 SCREW 2
53070-31 E-17 MOTOR 1
53070-32 E-18 TENSION CABLE 1
53070-33 E-19 END CAP 1
53070-34 F BELT WHEEL SET 1
53070-35 F-1 CRANK 1
53070-36 F-2 BELT WHEEL 1
53070-37 F-3 BELT 1
53070-38 F-4 ROUND MAGNET 1
53070-39 G FIXING PLATE FOR MAGNET SET 1
53070-40 G-1 FIXING PLATE FOR MAGNET 1
53070-41 G-2 HEX BOLT 1
53070-42 G-3 NUT 1
53070-43 G-4 FLAT WASHER 1
53070-44 G-5 NYLON WASHER 1
53070-45 G-6 NYLON NUT 1
53070-46 G-7 SPRING 1
53070-47 G-8 NYLON NUT 1
53070-48 G-9 HEX BOLT 1
53070-49 G-10 MAGNET CASE 5
53070-50 G-11 MAGNET 6
53070-51 H FLY WHEEL SET 1
53070-52 H-1 FLY WHEEL 1
53070-53 H-2 ANTI-LOOSEN NUT 2
YORK REF. REF. DESCRIPTION QTY.
53070-54 H-3 NUT 2
53070-55 H-4 C-CLIP 1
53070-56 H-5 FLYWHEEL AXLE 1
53070-57 H-6 FIXING RING 1
53070-58 H-7 SCREW COVER 1
53070-59 H-8 BEARING 2
53070-60 H-9 LITTLE WHEEL 1
53070-61 H-10 BEARING 1
53070-62 H-11 SINGLE WAY BEARING 1
53070-63 H-12 BEARING 2
53070-64 I FRONT STABILIZER SET 1
53070-65 I-1 FRONT STABILIZER 1
53070-66 I-2 OVAL CAP 2
53070-67 I-3 FOOT CAP WITH WHEEL 2
53070-68 I-4 SCREW 4
53070-69 J REAR STABILIZER SET 1
53070-70 J-1 REAR STABILIZER 1
53070-71 J-2 ADJUSTABLE WHEEL 2
53070-72 J-3 OVAL CAP 2
53070-73 K FIXING PLATE FOR IDLE WHEEL SET 1
53070-74 K-1 NYLON NUT 1
53070-75 K-2 IDLE WHEEL 1
53070-76 K-3 BUSHING 1
53070-77 K-4 ALLEN BOLT 1
53070-78 K-5 NYLON NUT 1
53070-79 K-6 NUT 1
53070-80 K-7 FLAT WASHER 1
53070-81 K-8 FIXING PLATE FOR IDLE WHEEL 1
53070-82 K-9 SPRING 1
53070-83 K-10 PLASTIC COVER 2
53070-84 K-11 PLASTIC WASHER 2
53070-85 K-12 HEX BOLT 1
53070-86 L SEAT SET 1
53070-87 L-1 SEAT 1
53070-88 L-2 FLAT WASHER 3
53070-89 L-3 NYLON NUT 3
53070-90 M CHAIN COVER SET 1
53070-91 M-1 LEFT CHAIN COVER 1
53070-92 M-2 RIGHT CHAIN COVER 1
53070-93 M-3 ROUND COVER 2
53070-94 M-4 SCREW 9
53070-95 M-5 ROUND RING FOR CHAIN COVER 1
53070-96 M-6 ROUND RING FOR CHAIN COVER 1
53070-97 N-1 ALLEN BOLT 4
53070-98 N-2 SPRING WASHER 10
53070-99 N-3 FLAT WASHER 4
53070-100 N-4 CURVED WASHER 6
53070-101 N-5 ALLEN BOLT 6
53070-102 O ADAPTOR 1
53070-103 P PEDAL 1
53070-104 P-1 LEFT PEDAL 1
53070-105 P-2 RIGHT PEDAL 1
www.yorkfitness.com
22
Notes
www.yorkfitness.comwww.yorkfitness.com
23
www.yorkfitness.com
Loading...