14OCT2011
Owner’s Manual
www.yorkfitness.com
Warrior Vertical Multigym
50031
www.yorkfitness.com
2
Congratulations on
purchasing your exercise
equipment from
You have chosen a high quality, safe and
innovative piece of equipment as your training
partner and we are certain it will keep you
motivated on the way to achieving your
personal fitness goals.
Please take the time to read this owner’s
manual as it will help you to get the most out
of your new exercise equipment.
For more information visit www.yorkfitness.com
CONTENTS
Safety information 03
Customer support 04
Assembly instructions 05
Care & Maintenance 28
User instructions 28
Fitness guide 30
Exploded drawing 31
Part list 35
Table of contents
www.yorkfitness.com
3
Safety information
Please read this instruction manual before you
begin assembly. Great care has been taken
to design these instructions and following
them will help you with quicker assembly and
minimize the risk of injury.
It is important that you keep these instructions
for future reference.
This list is not exhaustive - You are responsible
for your own safety!
• Assemble the product on a level surface.
• You will need at least one person to help you
assemble this unit.
• Always use the product on a level surface, ensure
that the product is stable before use.
• Always ensure that the equipment has adequate
space on each side and front (the back can be near
to a wall).
• Replace defective components immediately, and/or
keep the equipment out of use until it is repaired.
• Use only the adjustment settings as described in the
instructions. Always use the correct adjustment pin/
fixing.
• Always check that any pins / fixings are tight and
secure before use and / or after adjustment.
• Never leave any adjustment devices projecting from
the product.
• Always consult your doctor before undertaking any
exercise program.
• Always wear suitable clothing and footwear e.g.
tracksuit / shorts / training shoes.
• Remove all personal jewellery before exercising.
• Ensure you warm-up well before using the
equipment as this will help to prevent muscle strain.
• After eating, allow 1-2 hours before exercising as
this will help to prevent muscle strain.
• Injuries to health may result from incorrect or
excessive training.
• Never overload the equipment - the maximum user
load is displayed below and on the product label.
• We recommend that you do not lift weights alone.
There should be somebody there to assist you.
• Never use the equipment in any other manner other
than the ways explained in these instructions and/or
any wall-chart supplied.
• Parents and others in charge of children should be
aware of their responsibility, because the natural
play instinct and the fondness of experimenting of
children can lead to situations and behaviour for
which the training equipment is not intended.
• If children are allowed to use the equipment, their
mental and physical development and above all their
temperament should be taken into account. They
should be controlled and instructed in the correct
use of the equipment.
• The equipment is under no circumstances suitable
as a children’s toy.
• Children should not be allowed on, or around the
equipment - especially when it is not in use.
• This product has been tested for use in a home
environment and is warranted for In Home, personal,
family or household use.
• Due to our continuous policy of product
development, York Fitness reserves the right to
change specifications without notice.
CAUTION! The instructions must be followed carefully in
the assembly, use and maintenance of your equipment.
The warranty does not cover damage due to negligence
of the assembly, adjustment and maintenance
instructions described herein.
Maximum user weight: 125kg
Safety Standards
This gym meets the requirements of British and EU
safety standards EN957 parts 1, 2 and 4. Therefore the
product carries the following mark:
www.yorkfitness.com
4
Customer support
Customer Support
Should you require any assistance regarding this product please gather the following information and then contact us
using the details below:
• Serial No. - This can be found on the sticker below, located as indicated.
• Original purchase date
• Place of purchase
• Information about the place and conditions of use
• Precise description of the issue / defect
IMPORTANT!! - Please retain your sales receipt, York Fitness Customer Care may request
proof of purchase to validate eligibility for warranty service. Warranty cover starts from the
date shown on the proof of purchase.
Contact Us
ENGLAND
The best way to contact us is via the website:
www.yorkfitness.com
York Barbell UK Ltd.
York Way, Daventry,
England, NN11 4YB
Tel: 0844 225 3112
AUSTRALIA
The best way to contact us is via the website:
www.yorkfitness.com.au
York Fitness Australia
1/2 Swaffham Rd, Minto,
PO Box 5130, NSW 2566
Tel: 1800 730 149
Use only on a level surface
Not suitable for therapeutic purpose
Manufacturer: YORK BARBELL
Contact: www.yorkfitness.com
Product Name: YORK WARRIOR VERTICAL MULTIGYM
Max User Weight: 125KG
Safety Standards: EN957 Part 1, 2 & 4 - Class H
SERIAL NO:
50031-
Product’s Name
Serial Number
This product label is an example only, it is not the
real product name and serial number of the item
you have bought.
www.yorkfitness.com
5
Assembly instructions
• Prepare your work area - It is important you assemble the product in a clean and uncluttered space.
• Work with a friend - We recommend you have someone assist you with the assembly as
some of the components are quite heavy.
• Open the carton - Check any warnings on the carton and make sure you have it the right way up.
• Unpack the carton - Remove all the parts and lay them out on the floor.
Make sure you have the following parts:
1
x 1
MAIN STABILIZER ASSEMBLY
RIGHT
2
x 1
MAIN STABILIZER ASSEMBLY
LEFT
x 2
4
WEIGHT TUBE
OD25.4 X 1768.2 X 2MM
6
x 1
MAIN UPPER ASSEMBLY
7
x 1
REAR UPPER ASSEMBLY
8
x 1
SEAT MOUNT ASSEMBLY
9
x 1
LEG EXTENSION ASSEMBLY
12
x 1
PRESS-PEC ARM ASSEMBLY
RIGHT
13
x 1
PRESS LOCK ASEEMBLY
14
x 1
PREACHER CURL ASSEMBLY
x 2
FOAM TUBE
16
20
x 4
FOAM ROLLER
STANDARD (OD90 X L180MM)
21
x 2
FOAM ROLLER
MEDIUM (OD100 X L295MM)
28
x 1
VINYL TOP WEIGHT PLATE
3KG
29
x 1
VINYL WEIGHT STACK
STEM ASSEMBLY (50KG)
36
x 1
RATIO BRACKET ASSEMBLY
37
x 1
DOUBLE ADJUSTABLE PULLEY
BRACKET ASSEMBLY
38
x 1
DOUBLE PULLEY
BRACKET ASSEMBLY
41
x 1
LOW PULLEY BAR ASSEMBLY
42
x 1
LAT BAR ASSEMBLY
3
x 2
WEIGHT TUBE MOUNT ASSEMBLY
SHORT
5
x 1
MAIN UPRIGHT ASSEMBLY
10
x 1
UPPER PRESS-PEC ASSEMBLY
11
x 1
PRESS-PEC ARM ASSEMBLY
LEFT
17
x 1
UPHOLSTERY
MAIN
UPHOLSTERY
SHAPED
19
x 1
15
x 2
PRESS HANDLE
18
x 1
UPHOLSTERY
SMALL
22
x 4
HANDGRIP
ID21.5 X L140MM
23
x 2
RUBBER BUMPER
OD-63.5 X ID-26 X L-25MM
27
x 9
VINYL WEIGHT PLATE
5KG
43
x 1
PIVOT ROD
19 X 5 X 106MM
www.yorkfitness.com
6
25
x 15
PULLEY WHEEL
(Ø90MM)
26
x 24
PULLEY WHEEL COVER
30
x 1
MAIN STABILIZER
ASSEMBLY (RIGHT)
31
x 1
HAND WHEEL
FEMALE (M10)
32
x 1
BALL LOCK PIN
(M10 X 25MM)
33
x 1
CABLE ASSEMBLY
VINYL WEIGHT
34
x 1
CABLE ASSEMBLY
LAT / L2385MM
35
x 1
CABLE ASSEMBLY
PEC / L2640MM
39
x 1
CHAIN 19X LINKS
40
x 3
SNAP HOOK
(STANDARD)
44
x 4
BUSH
(15.8 X 10.5 X 6MM)
45
x 6
BUSH
(15.8 X 10.5 X 12MM)
46
x 2
BUSH
(15.8 X 10.5 X 8.5MM)
54
x 4
ALLEN HEAD BOLT
(M8 X 15MM)
55
x 4
CARRIAGE BOLT
M10 X 70MM
56
x 51
WASHER
(M10 X 23MM)
57
x 32
NYLOC NUT (M10)
58
x 1
CARRIAGE BOLT
M10 X 65MM
59
x 2
CARRIAGE BOLT
(M10 X 62MM)
60
x 1
CARRIAGE BOLT
M10 X 55MM
61
x 9
CARRIAGE BOLT
M10 X 50MM
62
x 1
HEX HEAD BOLT
M10 X 82MM
63
x 1
HEX HEAD BOLT
M10 X 80MM
64
x 4
HEX HEAD BOLT
M10 X 60MM
65
x 2
HEX HEAD BOLT
M10 X 55MM
66
x 2
HEX HEAD BOLT
M10 X 58MM
67
x 3
HEX HEAD BOLT
M10 X 65MM
68
x 1
HEX HEAD BOLT
M12 X 72MM
69
x 2
WASHER
M12 X 25MM
70
x 1
NYLOC NUT (M12)
71
x 1
HEX HEAD BOLT
M10 X 45MM
72
x 2
HEX HEAD BOLT
M8 X 65MM
73
x 12
WASHER
M8 X 20MM
74
x 2
HEX HEAD BOLT
M8 X 55MM
75
x 4
ALLEN HEAD BOLT
M8 X 20MM
76
x 4
WASHER
M8 X 28MM
77
x 2
BOLT CAP
M12 X 30MM
78
x 1
BALL LOCK PIN
M12 X 112MM
81
x 1
WEIGHT LOCK COLLAR
82
x 1
CROSS HEAD SCREW
M6 X 10MM
83
x 1
CAM COVER
(LEFT)
84
x 1
CAM COVER
(RIGHT)
85
x 4
CROSS HEAD SCREW
M4 X 10MM
86
x 4
BOLT CAP
M8 X 30MM
87
x 1
CABLE ASSEMBLY
LOW PULL / L3100MM
89
x 1
WASHER
M12 X 38MM
91
x 1
EYE BOLT
M10 X 115MM
92
x 1
HEX NUT (M10)
94
x 4
BUSH
12.7 X 8.3 X L8MM
95
x 2
NYLOC NUT (M8)
98
x 2
HEX HEAD BOLT
M8 X 60MM
Assembly instructions
www.yorkfitness.com
7
STEP 1
45
4
67
1
2
57
56
45
3
55
45
56
67
56
45
45
3
57
56
x 4
55
x 2
56
x 6
57
x 4
67
x 2
!
Fit Part #4 last
www.yorkfitness.com
8
STEP 2
Assembly instructions
55
x 2
x 8
57
x 5
64
x 3
56
6
56
56
56
5
56
56
57
57
64
64
55
57
www.yorkfitness.com
9
STEP 3
78
78
x 1
81
81
28
29
27
23
x 1
82
82
x 1
Fit Weights (27) one at
a time and alternate
the direction of the
end caps with the
bottom end cap facing
the left as illustrated
Apply weight labels starting
with 50kg/100kg at the
bottom as illustrated
www.yorkfitness.com
10
STEP 4
Assembly instructions
65
65
x 2
66
66
66
7
x 2
x 4
56
56
56
56
56
56
56
56
x 12
57
57
57
57
x 4
44
44
44
44
44
www.yorkfitness.com
11
STEP 5
56
56
56
8
x 3
57
57
57
x 3
58
58
x 1
59
59
59
x 2
www.yorkfitness.com
12
STEP 6
Assembly instructions
56
56
56
56
x 4
57
57
57
57
x 4
61
61
61
61
x 4
77
77
77
x 2
70
70
x 1
69
69
69
25
25
25
x 2
68
9
68
26
26
x 1
Please note correct position
of Pulley Wheel Covers
Tighten bolt before tting
caps (Do not over tighten)
✓✗
!
25
x 4
26
x 4
www.yorkfitness.com
13
STEP 7
56
56
56
56
56
62
63
71
57
57
13
56
57
25
25
26
Please note correct position
of Pulley Wheel Covers
✓✗
56
x 6
62
x 1
63
x 1
71
x 1
57
x 3
25
x 2
26
x 2
13
x 1
www.yorkfitness.com
14
STEP 8
Assembly instructions
56
56
56
56
57
57
64
25
25
26
26
Please note correct position
of Pulley Wheel Covers
✓✗
45
x 2
46
46
45
45
46
x 2
56
x 4
57
x 2
64
x 1
67
67
x 1
25
x 2
26
x 4
www.yorkfitness.com
15
STEP 9
56
56 56
x 2
57
57 57
x 2
61
61 61
x 2
25
25
26 26
Please note correct position
of Pulley Wheel Covers
✓✗
25
x 2
26
x 4
www.yorkfitness.com
16
STEP 10
Assembly instructions
NOTE: Plate face front.
Install Part #83 & #84 rst.
75
75
75
x 2
83
84
x 1
85
10
85
85
x 4
76
76
76
43
x 2
84
83
x 1
www.yorkfitness.com
17
STEP 11
22
15
12
86
94
73
95 86
21
11
74
73
94
RIGHT PEC ARM
FULLY
TIGHTEN BOLT
REPEAT ON
LEFT ARM
Fit Part #21 rst.
Lubricate Part #11
and #12 with
furniture polish
before tting of #21.
73
x 4
74
x 2
86
x 4
94
x 4
95
x 2
www.yorkfitness.com
18
STEP 12
Assembly instructions
76
75
76
75
75
x 2
76
x 2
Fit arms onto main
assembly and secure.
www.yorkfitness.com
19
STEP 13
89
33
91
92
26
25
36
56
57
32
START
HERE
FULLY ASSEMBLED
92
x 1
57
x 1
89
x 1
33
x 1
56
x 1
91
x 1
25
x 1
26
x 2
32
x 1
Secure ball end of
cable rst using Part
#32, then route bolt
end of cable as shown.
Screw bolt end of
cable #33 about
halfway into stem
#29, ensuring washer
#89 is in place. This
can be used to make
slight adjustments to
cable tension later,
secure by tightening
lock nut.
Please note correct position
of Pulley Wheel Covers
✓✗
www.yorkfitness.com
20
Assembly instructions
www.yorkfitness.com
21
STEP 14
26
25
61
37
56
57
25
26
34
Feed cable
through eye
bolt #91
START HERE
FULLY
ASSEMBLED
25
x 2
26
x 4
34
x 1
56
x 2
57
x 2
61
x 2
Screw Part #34
halfway into Part
#36, please leave
room for
adjustments.
Please note correct position
of Pulley Wheel Covers
✓✗
www.yorkfitness.com
22
STEP 15
26
25
25
60
56
35
57
61
38
26
NYLOC & WASHER
FITTED IN NEXT STEP
HOOK CABLE
HERE
FULLY
ASSEMBLED
25
x 2
26
x 4
35
x 1
56
x 1
57
x 1
60
x 1
61
x 1
Please note correct position
of Pulley Wheel Covers
✓✗
Assembly instructions
www.yorkfitness.com
23
STEP 16
87
57
56
FIX CABLE
END HERE
START HERE
56
x 2
57
x 1
87
x 1
Please note correct position
of Pulley Wheel Covers
Attach end of cable with
washer & nyloc as illustrated.
✓✗
www.yorkfitness.com
24
STEP 17
30
x 1
73
x 2
98
x 2
30
17
73 98
73
98
Assembly instructions
www.yorkfitness.com
25
STEP 18
18
20
16
73
20
72
72
x 2
73
x 2
Wide end of #18 to
be tted at front.
www.yorkfitness.com
26
STEP 19
19
14
73
54
31
31
x 1
54
x 4
73
x 4
Assembly instructions
www.yorkfitness.com
27
STEP 20
42
40
41
40
39
40
39
x 1
40
x 3
Go back and tighten all nuts
& bolts before use.
!
www.yorkfitness.com
28
User instructions
Press
1. Loosen hand wheel
2. Push hand wheel upwards out of way
3. Proceed with press exercise
Pec
1. Make sure that the hand wheel is in the down
position and screwed in tightly
2. Proceed with pec exercise
Lat & Low Pulley
1. Use chain to maximise distance of exercise
2. Clip snap hook onto required chain link to
attain desired start position
Care & Maintenance
• Use a warm, damp cloth to keep the product clean.
• The equipment should not be placed outdoors, or in a garage or outbuilding. Keep the
equipment in a dry place with as little temperature variation as possible.
• We recommend placing a mat beneath the equipment to protect both the equipment and
your flooring.
• The safety level of the equipment can be maintained only if it is regularly examined for
damage and wear. This includes any ropes, pulleys, nuts, bolts, moving parts, bushes,
chains, wheels, bearings & connection points etc.
• Ensure that you inspect the product regularly - at least once a week is recommended.
• Ensure that all fixings are tight before use.
• Always replace damaged / worn components with original parts from the manufacturer.
HAND WHE EL
HAND WHEEL
CHAIN
SNAP HOOK
www.yorkfitness.com
29
Ratio Adjustment
1. For 1:1 ratio (max 50kg) remove pin
from cable and place through bracket only
2. For 2:1 ratio (max 100kg) place pin
through bracket and cable
LOCK PIN
= 1:1 Ratio
= 2:1 Ratio
WEIGHT LABEL
!
User instructions
Leg Extension
1. Remove preacher pad by removing pin
2. Place pin behind seat in storage hole
3. Remove chain
4. Proceed with exercise
Place pin here
WEIGHT LOCK
When in use loosen
Screw in Locking Collar
so it moves up & down Freely.
To prevent accidents
when not in use ensure
the Weight Lock Collar is secured.
www.yorkfitness.com
30
Starting Your Workout
Begin each workout with a Warm Up session -
a few minutes of stretching to help prevent strains, pulls and cramps.
1. Perform some gentle stretching
2. Do light cardiovascular exercise (i.e. cycle) for approx 5-10 mins
3. ‘Dry-run’ one exercise per body part without using weights to ensure muscles and joints are warm
Finishing Your Workout
End each work-out with a warm down session – the purpose of this is to lower your heart rate slightly and to prevent
strains, pulls and cramps.
1. Perform 3-5 minutes of light cardiovascular work to gradually lower heart rate and reduce body temperature back
towards resting levels
2. Exercise should be rhythmical and of gradually decreasing intensity.
3. Stretch all the major muscle groups – this will aid recovery and return the muscles to their normal length
Correct Exercising Form
• Ensure joints remain soft (not locked out) and movements are carried out in a smooth and continuous way. (Each
repetition should take you approximately a slow count of 4 to do)
• Avoid using ‘momentum’ and instead focus on the muscles you are working - throwing weights with poor
technique increases the risk of injury and reduces training benefits
• Use full range of movement for each repetition performed
• Do not hold breath whilst training, instead exhale on the hardest phase of the exercise and inhale on the easier
phase e.g.) Bicep Curl – exhale as you curl dumbbell towards shoulder and inhale as you return the weight to the
start position
Choosing Your Weights
Start with a weight you can perform 12 repetitions without crossing the line from ‘challenged’ to ‘struggle’. If you
cannot maintain correct technique, the weight is too heavy!
Gradually increase the weight as you become stronger and more practiced.
Training for increased muscle size
• Keep your sets between 8 – 12 repetitions
• Repeat each individual exercise 2 or 3 times increasing weight slightly and decreasing repetitions i.e.. 1st set 12
repetitions, 2nd set 10 repetitions, 3rd set 8 repetitions
• Rest for 1 minute between sets
Training for shape/definition
• Sets should be 12 – 15 repetitions
• Repeat each individual exercise 1 or 2 times with sets of between 12 - 15 repetitions
• Rest for 1 minute between sets
Please see the accompanying wall chart for guidelines on how to perform specific exercises...
Fitness guide
www.yorkfitness.com
31
Exploded drawing
68
www.yorkfitness.com
32
Exploded drawing
www.yorkfitness.com
33
www.yorkfitness.com
34
Exploded drawing
www.yorkfitness.com
35
Part list
REF. YORK REF. DESCRIPTION QTY.
1 50031-1 MAIN STABILIZER ASSEMBLY - RIGHT 1
2 50031-2 MAIN STABILIZER ASSEMBLY - LEFT 1
3 50031-3 WEIGHT TUBE MOUNT ASSEMBLY - SHORT 2
4 50031-4 WEIGHT TUBE (OD25.4 X 1768.2 X 2MM) 2
5 50031-5 MAIN UPRIGHT ASSEMBLY 1
6 50031-6 MAIN UPPER ASSEMBLY 1
7 50031-7 REAR UPPER ASSEMBLY 1
8 50031-8 SEAT MOUNT ASSEMBLY 1
9 50031-9 LEG EXTENSION ASSEMBLY 1
10 50031-10 UPPER PRESS-PEC ASSEMBLY 1
11 50031-11 PRESS-PEC ARM ASSEMBLY - LEFT 1
12 50031-12 PRESS-PEC ARM ASSEMBLY - RIGHT 1
13 50031-13 PRESS LOCK ASEEMBLY 1
14 50031-14 PREACHER CURL ASSEMBLY 1
15 50031-15 PRESS HANDLE 2
16 50031-16 FOAM TUBE 2
17 50031-17 UPHOLSTERY - MAIN 1
18 50031-18 UPHOLSTERY - SMALL 1
19 50031-19 UPHOLSTERY - SHAPED 1
20 50031-20 FOAM ROLLER - STANDARD (OD90 X L180MM) 4
21 50031-21 FOAM ROLLER - MEDIUM (OD100 X L295MM) 2
22 50031-22 HANDGRIP (ID21.5 X L140MM) 4
23 50031-23 RUBBER BUMPER (OD-63.5 X ID-26 X L-25MM) 2
24 50031-24 RUBBER SHOP (Ø25 X 8MM) 2
25 50031-25 PULLEY WHEEL (Ø90MM) 15
26 50031-26 PULLEY WHEEL COVER 24
27 50031-27 VINYL WEIGHT PLATE - 5KG 9
28 50031-28 VINYL TOP WEIGHT PLATE - 3KG 1
29 50031-29 VINYL WEIGHT STACK - STEM
ASSEMBLY (50KG)
1
30 50031-30 HAND WHEEL - FEMALE (M10) 1
31 50031-31 BALL LOCK PIN (M10 X 65MM) 1
32 50031-32 BALL LOCK PIN (M10 X 25MM) 1
33 50031-33 CABLE ASSEMBLY - VINYL WEIGHT / L1985MM 1
34 50031-34 CABLE ASSEMBLY - LAT / L2385MM 1
35 50031-35 CABLE ASSEMBLY - PEC / L2640MM 1
36 50031-36 RATIO BRACKET ASSEMBLY 1
37 50031-37 DOUBLE ADJUSTABLE PULLEY
BRACKET ASSEMBLY
1
38 50031-38 DOUBLE PULLEY BRACKET ASSEMBLY 1
39 50031-39 CHAIN - 19X LINKS 1
40 50031-40 SNAP HOOK (STANDARD) 3
41 50031-41 LOW PULLEY BAR ASSEMBLY 1
42 50031-42 LAT BAR ASSEMBLY 1
43 50031-43 PIVOT ROD (19 X 5 X 106MM) 1
44 50031-44 BUSH (OD-15.8 X ID-10.5 X L-6MM) 4
45 50031-45 BUSH (OD-15.8 X ID-10.5 X L12MM) 6
46 50031-46 BUSH (OD-15.8 X ID-10.5 X L8.5MM) 2
47 50031-47 ROUND INTERNAL END CAP (Ø25.4MM) 4
48 50031-48 SQUARE FLAT INTERNAL END CAP
(SQ-50MM / 1.5MM TUBE)
3
49 50031-49 SQUARE FLAT INTERNAL END CAP
(SQ-38MM / 1.5MM TUBE)
7
50 50031-50 ROUND FLAT INTERNAL END CAP
(OD38.1MM)
2
REF. YORK REF. DESCRIPTION QTY.
51 50031-51 SQUARE FLAT INTERNAL END CAP
(SQ-45MM / 1.5MM TUBE)
1
52 50031-52 RECTANGLE FLAT INTERNAL END CAP
(25 X 50MM / 1.5MM TUBE)
4
53 50031-53 RECTANGLE FLAT INTERNAL END CAP
(20 X 40MM / 1.5MM TUBE)
2
54 50031-54 ALLEN HEAD BOLT (M8 X 15MM) 4
55 50031-55 CARRIAGE BOLT (M10 X 70MM) 4
56 50031-56 WASHER (M10 X OD-23MM) 51
57 50031-57 NYLOC NUT (M10) 32
58 50031-58 CARRIAGE BOLT (M10 X 65MM) 1
59 50031-59 CARRIAGE BOLT (M10 X 62MM) 2
60 50031-60 CARRIAGE BOLT (M10 X 55MM) 1
61 50031-61 CARRIAGE BOLT (M10 X 50MM) 9
62 50031-62 HEX HEAD BOLT (M10 X 82MM) 1
63 50031-63 HEX HEAD BOLT (M10 X 80MM) 1
64 50031-64 HEX HEAD BOLT (M10 X 60MM) 4
65 50031-65 HEX HEAD BOLT (M10 X 55MM) 2
66 50031-66 HEX HEAD BOLT (M10 X 58MM) 2
67 50031-67 HEX HEAD BOLT (M10 X 65MM) 3
68 50031-68 HEX HEAD BOLT (M12 X 72MM) 1
69 50031-69 WASHER (M12 X OD-25MM) 2
70 50031-70 NYLOC NUT (M12) 1
71 50031-71 HEX HEAD BOLT (M10 X 45MM) 1
72 50031-72 HEX HEAD BOLT (M8 X 65MM) 2
73 50031-73 WASHER (M8 X OD-20MM) 12
74 50031-74 HEX HEAD BOLT (M8 X 55MM) 2
75 50031-75 ALLEN HEAD BOLT (M8 X 20MM) 4
76 50031-76 WASHER (M8 X OD-28MM) 4
77 50031-77 ROUND PLASTIC BOLT CAP (M12 X OD-30MM) 2
78 50031-78 BALL LOCK PIN (M12 X 112MM) 1
79 50031-79 CROSS HEAD SCREW (M4 X 10MM) 2
80 50031-80 RUBBER SLEEVE / L80MM 2
81 50031-81 WEIGHT LOCK COLLAR 1
82 50031-82 CROSS HEAD SCREW (M6 X 10MM) 1
83 50031-83 CAM COVER - LEFT 1
84 50031-84 CAM COVER - RIGHT 1
85 50031-85 COUNTER SUNK - CROSS HEAD
SCREW (M4 X 10MM)
4
86 50031-86 ROUND PLASTIC BOLT CAP (M8 X OD-30MM) 4
87 50031-87 CABLE ASSEMBLY - LOW PULL / L3100MM 1
88 50031-88 ROUND DOMED INTERNAL END CAP
(OD-38.1MM)
2
89 50031-89 WASHER (M12 X OD-38MM) 1
90 50031-90 REDUCER INSERT (45 > 38MM) 2
91 50031-91 EYE BOLT (M10 X 115MM) 1
92 50031-92 HEX NUT (M10) 1
93 50031-93 HANDGRIP (STANDARD) / OD31.8 X L130MM 4
94 50031-94 BUSH (OD-12.7 X ID-8.3 X L8MM) 4
95 50031-95 NYLOC NUT (M8) 2
96 50031-96 SQUARE FLAT INTERNAL END CAP
(SQ-38MM /2MM TUBE)
1
97 50031-97 STEM END CAP 1
98 50031-98 HEX HEAD BOLT (M8 X 60MM) 2
99 50031-99 FIXING BLISTER PACK 1
www.yorkfitness.com
Loading...