York TM9T User Manual

TECHNICAL GUIDE
96% TWO STAGE GAS-FIRED RESIDENTIAL MULTI-POSITION GAS FURNACES
MODELS: TM9T
NATURAL GAS 60 - 120 MBH INPUT
Visit us on the web at www.york.com for the most up-to-date technical information.
Additional efficiency rating information can be found at www.gamanet.org.
EFFICIENCY RATING CERTIFIED
ISO 9001
Certified Quality
Management System
WARRANTY
Lifetime limited warranty on both heat exchangers to the origi­nal purchaser; a 20-year limited warranty from original installa­tion date to subsequent purchaser.
10-year warranty on the heat exchanger in commercial applica­tions. 5-year limited parts warranty.
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
444559-YTG-A-0409
DESCRIPTION
These compact units employ induced combustion, reliable hot surface ignition and high heat transfe r aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications.
These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.
These units are Category IV listed and may be vented either through side wall or roof applications using approved plastic combustion air and venr piping.
FEATURES
Two stage heating operation includes two stage gas valve, two stage inducer operation and 4 speed, direct drive PSC motor blower operation. Adjustable delay timer allows two stage operation with a single stage thermostat.
Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary.
Compact, easy to install, ideal height 33" tall cabinet.
Blower-off delay for cooling SEER improvement.
Easy access to controls to connect power/control wiring.
Built-in, high level self diagnostics with fault code display.
Low unit amp requirement for easy replacement application.
All models are convertable to use propane (LP) gas.
Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability.
100% shut off main gas valve for extra safety.
24V, 40 VA control transformer and blower relay supplied for add-on cooling.
Hi-tech tubular aluminized steel primary heat exchanger with stainless steel tube/aluminum fin secondary heat exchanger for outstanding efficiency.
Solid removable bottom panel allows easy conversion.
Airflow leakage less than 1% of nominal airflow at ductblaster conditions.
No knockouts to deal with, making installation easier.
Movable duct connector flanges for application flexibility.
Quiet inducer operation.
Inducer rotates for easy conversion of venting options.
Fully supported blower assembly for easy access and removal of blower.
External air filters used for maximum flexibility in meeting customers IAQ needs.
Insulated blower compartment for thermal and acoustic performance.
1/4 turn knobs provided for easy independent door removal.
Internal condensate trap design (patent pending) provides condensate management options, easy visual operation check, and is self priming to prevent nuisance problems.
Protection included from air intake, exhaust vent or condensate blockage.
Venting applications maybe installed as either 2 pipe sealed combustion or single pipe vent using indoor combustion air.
444559-YTG-A-0409
FRONT
33
A
LEFT SIDE
Combustion Air Inlet
Condensate Drain (Downflow)
Vent Outlet
Thermostat Wiring
28.5”
Gas Pipe Entry
Electrical Entry
Condensate Drain
Thermostat Wiring
RIGHT SIDE
Vent Outlet
Condensate Drain (Downflow)
14”
1”
1.5”
23”
Combustion Air Inlet
Gas Pipe Entry
Electrical Entry
Condensate Drain
Optional Return Air Cutout (Either side)
29.5”
C
SUPPLY END
.56”
.56”
20”
B
3”
23.8”
.56”
Combustion Air Inlet
Vent Outlet
RETURN END
B
24.25”
Cabinet & Duct Dimensions
BTUH (kW)
Input
Nominal
CFM (m
3
/min)
Cabinet
Size
Cabinet Dimensions (Inches)
ABC Lbs
TM9T060B12MP11 1200 B 17 1/2 16 3/8 13 1/4 122 TM9T080B12MP11 1200 B 17 1/2 16 3/8 14 3/4 126 TM9T080C16MP11 1600 C 21 19 7/8 16 1/2 136 TM9T100C16MP11 1600 C 21 19 7/8 18 1/4 142 TM9T100C20MP11 2000 C 21 19 7/8 18 1/4 145 TM9T120D20MP11 2000 D 24 1/2 23 3/8 21 3/4 156
Approximate
Operating Weights
Ratings & Physical / Electrical Data
Input
Model
TM9T060B12MP11 60/39 58/37 10 96 35 - 65 35 - 65 TM9T080B12MP11 80/52 77/50 10 96 45 - 75 20 - 50 TM9T080C16MP11 80/52 77/50 11.5 96 45 - 75 25 - 55 TM9T100C16MP11 100/65 96/62 11.5 96 35 - 65 35 - 65 TM9T100C20MP11 100/65 96/62 17 96 45 - 75 20 - 50 TM9T120D20MP11 120/78 115/75 17 96 45 - 75 35 - 65
Model
High/Low
MBH MBH Amps % °F °F
Max. Outlet
Air Temp.
°F HP Amps In.
TM9T060B12MP11 170 0.50 7 11 x 8 15 14 TM9T080B12MP11 175 0.50 7 11 x 8 15 14 TM9T080C16MP11 175 0.75 8.8 11 x 10 15 14 TM9T100C16MP11 175 0.75 8.8 11 x 10 15 14 TM9T100C20MP11 175 1.00 14.5 11 x 11 20 12 TM9T120D20MP11 180 1.00 14.5 11 x 11 20 12
Annual Fuel Utilization Efficiency (AFUE) numbers are determined in accordance with DOE Test procedures. Wire size and over current protection must comply with the National Electrical Code (NFPA-70-latest edition) and all local codes. The furnace shall be installed so that the electrical components are protected from water.
2 Johnson Controls Unitary Products
Output
High/Low
Blower
Total
Unit
AFUE
Blower
Size
High Fire
Air Temp. Rise
Max.
Over-current
Protect
Low Fire
Air Temp. Rise
Min. Wire Size
(awg) @ 75 ft.
One Way
444559-YTG-A-0409
FILTER PERFORMANCE
The airflow capacity data published in the “Blower Perfor­mance” table listed above represents blower performance WITHOUT filters.
All applications of these furnaces require the use of field installed air filters. All filter media and mounting hardware or provisions must be field installed external to the furnace cabi­net. DO NOT attempt to install any filters inside the furnace.
NOTE: Single side return above 1800 CFM is approved as long as the filter velocity does not exceed filter manufacturer ’s rec­ommendation and a transition is used to allow use on a 2 0x25 filter.
Recommended Filter Sizes (High velocity 600 FPM)
CFM
1200 B 16 x 25 16 x 25 1600 C 16 x 25 20 x 25 2000 C (2) 16 x 25 20 x 25 2000 D (2) 16 x 25 22 x 25
NOTES:
1. Air velocity through throwaway type filters may not exceed 300 feet per minute (91.4 m/min). All velocities over this require the use of high velocity filters.
2. Do not exceed 1800 CFM using a single side return and a 16x25 fil­ter. For CFM greater than 1800, yo u may use t wo si de ret urns or one side and the bottom or one return with a transition to allow use of a 20x25 filter.
Cabinet
Size
Side
(in)
Bottom
(in)
Unit Clearances to Combustibles
Application
Top 1" 0" 0" Vent 0" 0" 0" Rear 0" 0" 0" Side 0" 0" 1"
Front* 0" 0" 0"
Floor Combustible
Closet Yes Yes Yes
Line Contact No No Yes
1. For combustible floors only when used with special sub-base. * - 24" clearance in front and 18" on side recommended for service access. All furnaces approved for alcove and attic installation.
Upflow Downflow Horizontal
1
Combustible
Combustible
ACCESSORIES
PROPANE (LP) CONVERSION KIT -
S1-1NP0347 - All Models This accessory conversion kit may be used to convert natural
gas (N) units for propane (LP) operation. CONCENTRIC VENT TERMINATION -
S1-1CT0302 (2") & S1-1CT0302-636 (2") S1-1CT0303 (3") & S1-1CT0303-636 (3") For use through rooftop, sidewall. Allows combustion air to
enter and exhaust to exit through single common hole. Elimi­nates unslightly elbows for a cleaner installation.
SIDEWALL VENT TERMINATION KIT -
S1-1HT0901 (3") S1-1HT0902 (2") For use on sidewall, two-pipe installations only. Provide a more attractive termination for locations where the terminal is visable on the side of the home.
CONDENSATE NEUTRALIZER KIT - 1NK0301
Neutralizer cartridge has a 1/2" plastic tube fittings for installa­tion in the drain line. Calcium carbonate refill media is also available from the Source 1 Parts (p/n 026-30228-000).
SIDE RETURN FILTER RACKS -
S1-1SR0200 - All Models S1-1SR0402 - All Models
BOTTOM RETURN FILTER RACKS -
S1-1BR0517 or 1BR0617 - For 17-1/2” cabinets S1-1BR0521 or 1BR0621 - For 21” cabinets S1-1BR0524 or 1BR0624 - For 24-1/2” cabinets
1BR05xx series are galvanized steel filter racks. 1BR06xx are pre-painted steel filter racks to match the appearance of the fur­nace cabinet.
COMBUSTIBLE FLOOR BASE KIT -
For installation of these furnaces in downflow applications directly onto combustible flooring material, These kits are required to prevent potential overheating situations.tible floor base kit provides access for combustible airflow. S1-1CB0517 - For 17-1/2” cabinets S1-1CB0521 - For 21” cabinets
S1-1CB0524 - For 24-1/2” cabinets
EAC TRANSITION KITS -
For installation of EAC accessories with these furnaces to pro­vide easy transition of return airflow through the EAC to get the proper sealing and reduced airflow leakage.
S1-1TK1001 - For all models using side return S1-1TK1017 - For 17-1/2” cabinets using bottom return S1-1TK1021 - For 21” cabinets using bottom return S1-1TK1024 - For 24-1/2” cabinets using bottom return
HIGH ALTITUDE PRESSURE SWITCHES -
For installation where the altitude is less than 5,000 feet it is not required that the pressure switch be changed. For altitudes above 5,000 feet, see kits below.
S1-1PS3306 - 080 S1-1PS3307 - 060 S1-1PS3302 - 100, 120
ROOM THERMOSTATS - A wide selection of compatible ther­mosets are available to provide optimum performance and fea­tures for any installation.
1H/1C, manual change-over electronic non-programmable ther­mostat.
1H/1C, auto/manual changeover, electronic programmable, deluxe 7-day, thermostat.
1H/1C, auto/manual changeover, electronic programmable. * For the most current accessory information, refer to the price
book or consult factory.
Johnson Controls Unitary Products 3
Blower Performance CFM - Any Position (without filter)
Bottom Airflow Data (SCFM)
Models Speed
High 1492 1442 1378 1325 1243 1176 1075 966 849 655
TM9T060B12MP11
Medium High 1236 1201 1161 1139 1082 1011 919 830 715 590
Medium Low 986 950 961 916 872 831 757 703 600 510
Low 824 795 783 744 713 659 624 554 489 389
High 1597 1537 1484 1435 1370 1286 1230 1155 1075 925
TM9T080B12MP11
Medium High 1338 1307 1273 1223 1179 1123 1065 998 928 812
Medium Low 1113 1094 1077 1043 1008 972 924 868 803 798
Low 937 916 900 877 854 817 775 718 639 560
High 1919 1865 1802 1738 1671 1600 1517 1414 1322 1201
TM9T080C16MP11
Medium High 1532 1533 1513 1499 1465 1416 1352 1283 1198 1084
Medium Low 1232 1313 1291 1280 1250 1209 1207 1148 1055 937
Low 826 821 853 858 838 817 794 776 760 711
High 1909 1880 1823 1776 1706 1637 1562 1474 1375 1252
TM9T100C16MP11
Medium High 1465 1463 1469 1485 1477 1416 1386 1324 1250 1114
Medium 1190 1222 1216 1215 1224 1189 1158 1145 1087 996
Low 787 834 819 836 819 810 790 761 690 707
High 2284 2205 2114 2021 1934 1848 1752 1653 1505 1397
TM9T100C20MP11
Medium High 1967 1905 1824 1763 1712 1628 1551 1473 1379 1213
Medium Low 1610 1563 1513 1480 1430 1367 1319 1261 1101 1012
Low 1326 1304 1267 1232 1183 1143 1080 1003 871 798
High 2341 2245 2153 2072 1977 1876 1769 1642 1506 1306
TM9T120D20MP11
Medium High 2002 1952 1878 1823 1739 1657 1563 1458 1322 1185
Medium Low 1615 1579 1533 1473 1430 1368 1282 1186 1091 953
Low 1352 1295 1259 1245 1190 1141 1076 998 938 820
Models Speed
High 1470 1406 1361 1309 1241 1155 1060 920 775 628
TM9T060B12MP11
Medium High 1211 1186 1139 1101 1042 980 896 796 681 545
Medium Low 970 957 927 889 853 796 745 660 568 450
Low 793 781 756 724 694 653 585 530 469 382
High 1605 1562 1514 1454 1393 1330 1251 1169 1073 940
TM9T080B12MP11
Medium High 1372 1318 1280 1255 1205 1161 1093 1023 943 849
Medium Low 1087 1073 1052 1003 993 953 897 843 775 709
Low 916 896 881 854 831 802 757 708 642 574
High 1956 1907 1846 1778 1717 1647 1573 1483 1353 1209
TM9T080C16MP11
Medium High 1543 1543 1516 1504 1477 1446 1382 1309 1202 1099
Medium Low 1238 1241 1243 1241 1252 1242 1201 1140 1074 967
Low 906 902 903 910 888 866 859 829 795 743
High 1828 1829 1789 1768 1727 1671 1601 1505 1390 1272
TM9T100C16MP11
Medium High 1422 1444 1437 1424 1396 1326 1301 1253 1200 1100
Medium 1224 1229 1243 1234 1219 1193 1168 1135 1088 977
Low 813 819 818 814 783 762 756 732 690 642
High 2391 2286 2165 2079 2004 1934 1839 1692 1560 1366
TM9T100C20MP11
Medium High 1945 1878 1838 1782 1694 1642 1565 1451 1334 1163
Medium Low 1549 1530 1495 1430 1431 1365 1284 1192 1097 1022
Low 1256 1229 1189 1159 1089 1033 1008 950 871 784
High 2343 2253 2167 2071 1979 1881 1785 1668 1473 1351
TM9T120D20MP11
Medium High 1954 1892 1846 1781 1714 1637 1548 1429 1238 1171
Medium Low 1596 1539 1511 1458 1399 1341 1254 1180 942 988
Low 1299 1261 1229 1177 1111 1053 993 937 882 782
NOTES:
1. Airflow expressed in standard cubic feet per minute (CFM).
2. Return air is through side opposite motor (left side).
3. Motor voltage at 115 V.
4. Airflow through across motor side (right side) may be slightly less than the data shown above.
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Left Side Airflow Data (SCFM)
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Ext. Static Pressure (in. H2O)
Ext. Static Pressure (in. H2O)
Subject to change without notice. Printed in U.S.A. 444559-YTG-A-0409 Copyright © 2009 by Johnson Controls, Inc. All rights reserved. Supersedes: Nothing
Johnson Controls Unitary Products
5005 York Drive
Norman, OK 73069
Loading...