York THGD18 THRU 60 User Manual

TECHNICAL GUIDE

V A

SPLIT-SYSTEM HEAT PUMPS

13 SEER – R-22 MODELS:

THGD18 THRU 60 (1.5 THRU 5 NOMINAL TONS, 1 PHASE)

LISTED

Due to continuous product improvement, specifications are subject to change without notice.

isit us on the web at www.york.com dditional rating information can be found at

ww.ahridirectory.org

ISO 9001

Certified Quality

Management System

365147-YTG-C-0608

DESCRIPTION

The heat pump condensing unit is the outdoor part of a versatile system of heating and air conditioning. It is designed to be custom-matched with one of UPG’s complete line of evaporator sections, with each serving a specific function. Matching Air Handlers are available for upflow, downflow, or horizontal applications to provide a complete system. Electric Heaters are available, if required. Add-on coils are available for use with upflow, downflow, or horizontal furnaces and air handlers.

WARRANTY

Single Phase Units:

5-year limited parts warranty. 5-year limited compressor warranty.

FEATURES

• QUALITY CONDENSER COILS - The coil is constructed of copper tubing and enhanced aluminum fins for increased efficiency and corrosion protection.

• PROTECTED COMPRESSOR - The compressor is internally protected against high pressure, temperature, and externally by a factory installed high pressure switch. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor.

• DURABLE FINISH - The cabinet is made of pre-painted steel. The pre-treated galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted-textured finish insure less fading when exposed to sunlight.

• LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof.

• TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications.

• LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds.

• LOW MAINTENANCE - Long life permanently lubricated motor-bearings need no annual servicing.

• EASY SERVICE ACCESS - Fully exposed refrigerant connections, and a single panel covering the electrical controls make for easy servicing of the unit.

• SECURED SERVICE VALVES - Secured re-usable ser- vice valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.

• U.L. and C.U.L. listed - approved for outdoor application.

Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

365147-YTG-C-0608

Physical and Electrical Data

MODEL

THGD18

S21S1

THGD24

S21S1

THGD30

S21S1

THGD36

S21S1

THGD42

S21S1

THGD48

S21S1

THGD60

S21S1

Unit Supply Voltage 208-230V, 1φ, 60Hz Normal Voltage Range

187 to 252

Minimum Circuit Ampacity 9.9 13.1 17.7 19.8 24.9 40.1 40.1 Max. Overcurrent Device Amps Min. Overcurrent Device Amps

15 20 30 30 40 50 60 15 15 20 20 25 45 45

Compressor Type Recip Recip Recip Recip Recip Scroll Scroll Compressor Amps

Rated Load 7.6 9.9 13.1 14.6 18.7 30.9 30.9

Locked Rotor 36 54 61 78 78 115 150 Crankcase Heater Yes Yes Yes Yes Yes No No Fan Motor Amps Rated Load 0.5 1.5 1.4 1.5 1.5 1.5 1.5 Fan Diameter Inches 24 24 24 24 24 24 24

Rated HP 1/15 1/10 1/4 1/4 1/4 1/4 1/4 Fan Motor

Nominal RPM 850 825 1100 850 850 850 850

Nominal CFM 2050 2250 3700 3700 3600 3450 3600

Face Area Sq. Ft. 15.72 18.34 20.96 23.58 23.58 24.00 27.00 Coil

Rows Deep1111122

Fin / Inches 22 22 22 22 22 22 22 Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line Set OD (Field Installed) 3/4 3/4 3/4 7/8 7/8 7/8 1-1/8

Unit Charge (Lbs. - Oz.)

7 - 3 7 - 7 8 - 12 9 - 1 11 - 14 13 - 4 15 - 5

Charge Per Foot, Oz. 0.68 0.68 0.68 0.70 0.70 0.70 0.76 Operating Weight Lbs. 172 184 196 208 208 275 280

1.Rated in accordance with ARI Standard 110, utilization range “A”.

2.Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection.

3.Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection.

4.The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.

All dimensions are in inches. They are subject to change without notice. Certified dimensions will be provided upon

request.

Unit

Model

18 28

(Inches)

B C Liquid Vapor

34 34 24 32 34 34 30 36 34 34 36 40 34 34

48 40 34 34 60 40 34 34 1-1/8”

1. Including Fan Guard. * Adapter fitting required for 1-1/8” line set.

Dimensions

Refrigerant Connection

Service Valve Size

3/8”

3/4”

7/8”42 40 34 34

2 Johnson Controls Unitary Products

365147-YTG-C-0608

Additional R-22 Charge / Orifice Size for Various Matched Systems

Outdoor Unit

Required Orifice or TXV

THGD18

S21S1

1TVM2A1 1TVM2A1 1TVM2A1 1TVM2A1 1TVM2C1 1TVM2C1 1TVM2C1

Factory Charge, lbs-oz 7 - 3 7 - 7 8 - 12 9 - 1 11 - 14 13 - 4 15 - 5

THGD24

S21S1

THGD30

S21S1

THGD36

S21S1

THGD42

S21S1

THGD48

S21S1

THGD60

S21S1

Indoor Coil

2,3

Additional Charge, Oz

FC/MC/PC/UC18A2A 0 –––––– FC/MC/PC/UC18B2A 0 –––––– FC/MC/PC/UC24A2A 0 0 ––––– FC/MC/PC/UC24B2A 0 0 ––––– FC/MC/PC/UC30A2A 0 0 ––––– FC/MC/PC/UC30B2A 0 0 ––––– FC/MC/PC/UC32A2A –5 0 –––– FC/MC/PC/UC35B2A –5 0 –––– FC/MC/PC/UC35C2A –5 0 –––– FC/MC/PC/UC37A2A – – 0 0 – – – FC/MC/PC/UC43C2C ––––––– FC/MC/PC/UC48C2C ––––0 –– FC/MC/PC/UC48D2C ––––0 –– FC/PC/UC60C2C ––––2 0 – FC/MC/PC/UC60D2C ––––2 0 – FC/PC62D2C –––––2 0 HC18A2A 0 –––––– HC30A2A –0 ––––– HC36B2A –5 0 –––– HC60C2C ––––2 0 – HD24A2A –4 ––––– HD36B2A ––0 –––– HD60D2C ––––2 0 – MH30S2A –6 ––––– AHP18B2A 0 –––––– AHP24B2A 0 0 ––––– AHP30B2A –5 0 –––– AHP36C2A – – 0 0 – – – AHP48D2C ––––2 0 – AHP60D2C ––––2 0 – AV24B2A 0 0 ––––– AV36C2A ––0 0 ––– AV48D2C ––––0 0 – AV60D2C ––––0 0 – FC/MC/PC/UC18A3X 2A + 0 –––––– FC/MC/PC/UC18B3X 2A + 0 –––––– FC/MC/PC/UC24A3X 2A + 0 2A + 0 ––––– FC/MC/PC/UC24B3X 2A + 0 2A + 0 ––––– FC/MC/PC/UC30A3X –2A + 0 ––––– FC/MC/PC/UC30B3X –2A + 0 ––––– FC/MC/PC/UC32A3X –2A + 5 2A + 0 –––– FC/MC/PC/UC35B3X –2A + 5 2A + 0 –––– FC/MC/PC/UC35C3X –2A + 5 2A + 0 –––– FC/MC/PC/UC37A3X – – 2A + 0 2A + 0 – – – FC/MC/PC/UC43B3X – – 2A + 0 2A + 0 – – – FC/MC/PC/UC43C3X – – 2A + 0 2A + 0 – – – FC/MC/PC/UC48C3X – – – 2A + 3 2C + 0 – – FC/MC/PC/UC48D3X – – – 2A + 3 2C + 0 – – FC/PC/UC60C3X – – – 2A + 5 2C + 2 2C + 0 – FC/MC/PC/UC60D3X – – – 2A + 5 2C + 2 2C + 0 – FC/PC62D3X –––––2C + 2 2C + 0 For Notes See Page 4.

Johnson Controls Unitary Products 3

365147-YTG-C-0608

Additional R-22 Charge / Orifice Size for Various Matched Systems (Continued)

Outdoor Unit

Required Orifice or TXV

THGD18

S21S1

1TVM2A1 1TVM2A1 1TVM2A1 1TVM2A1 1TVM2C1 1TVM2C1 1TVM2C1

Factory Charge, lbs-oz 7 - 3 7 - 7 8 - 12 9 - 1 11 - 14 13 - 4 15 - 5

THGD24

S21S1

THGD30

S21S1

THGD36

S21S1

THGD42

S21S1

THGD48

S21S1

THGD60

S21S1

Indoor Coil

2,3

Additional Charge, Oz

HC18A3X 2A + 0 –––––– HC30A3X –2A + 0 ––––– HC36B3X –2A + 5 2A + 0 –––– HC42C3X – – 2A + 0 2A + 0 – – – HC60C3X – – – 2A + 5 2C + 2 2C + 0 – HD24A3X –2A + 4 ––––– HD36B3X ––2A + 0 –––– HD48C3X – – – 2A + 3 – – – HD60D3X – – – 2A + 5 2C + 2 2C + 0 – MH24S59 –2A + 6 2A + 0 –––– MH30S65 –2A + 6 2A + 0 –––– AHP18B3X 2A + 0 –––––– AHP24B3X 2A + 0 2A + 0 ––––– AHP30B3X –2A + 5 2A + 0 –––– AHP36C3X – – 2A + 0 2A + 0 – – – AHP42C3X – – – 2A + 0 – – – AHP48D3X ––––2C + 2 2C + 0 – AHP60D3X – – – 2A + 5 2C + 2 2C + 0 – AV24B2A 2A + 0 2A + 0 ––––– AV36C2A – – 2A + 0 2A + 0 – – – AV48D2C – – – 2A + 0 2C + 0 2C + 0 – AV60D2C ––––2C + 0 2C + 0 – F4FP024 0 –––––– F4FP030 –0 ––––– F4FP040 ––0 –––– F5FP045 – – – 2A + 5 2 – – F5FP048 – – – 2A + 3 0 – – F5FP060 – – – 2A + 5 2 0 – F4FV060 – – – 2A + 0 0 0 –

FOOTNOTES:

1.For applications requiring a TXV use 1TVM series kit.

2.Systems matched with furnace or air handlers not equipped with blower-off delays may require blower Time Delay Kit 2FD06700224.

3.PC coils cannot be used in downflow or horizontal applications. FC coils cannot be used in horizontal applications.

PROCEDURES:

1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and 15 feet of interconnecting line tubing.

2. Verify the TXV or orifice and additional charge required for specific evaporator coil in the system using the above table.

3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in Physical and Electrical Data Table.

4. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaporator + adder for line set.

4 Johnson Controls Unitary Products

365147-YTG-C-0608

COOLING CAPACITY - With Air Handler Coils

UNIT

MODEL

THGD18S21S1

THGD24S21S1

THGD30S21S1

THGD36S21S1

THGD42S21S1

THGD48S21S1

THGD60S21S1 MA20D 24 FC/MC62D 1800 55.0 40.0 13.00 11.00

THGD18S21S1

THGD24S21S1

THGD30S21S1

THGD36S21S1

THGD42S21S1

THGD48S21S1

THGD60S21S1 MV20D 24 FC/MC62D 1800 55.0 40.5 13.50 11.00

For Notes See Page 6.

AIR HANDLER

MODEL W

MA08B 17 FC/MC18B 600 18.0 12.9 13.00 11.00 MA08B 17 FC/MC24B 600 18.0 12.9 13.00 11.00 MA08B 17 FC/MC30B 600 18.0 12.9 13.00 11.00 MA08B 17 FC/MC24B 800 23.0 16.8 13.00 11.00 MA08B 17 FC/MC30B 800 23.0 16.8 13.00 11.00 MA08B 17 FC/MC35B 800 23.0 16.8 13.00 11.00 MA12B 17 FC/MC35B 1000 29.0 21.2 13.00 11.00 MA12B 17 FC/MC43B 1000 29.0 21.2 13.00 11.00 MA12B 17 FC/MC43B 1200 35.0 25.6 13.00 11.00 MA14D 24 FC/MC48D 1200 35.0 25.6 13.00 11.00 MA14D 24 FC/MC60D 1200 35.0 25.6 13.00 11.00 MA14D 24 FC/MC48D 1400 40.0 28.8 13.00 11.00 MA16C 21 FC/MC48C 1400 40.0 28.8 13.00 11.00 MA14D 24 FC/MC60D 1400 40.0 28.8 13.00 11.00 MA16C 21 FC60C 1400 40.0 28.8 13.00 11.00 MA16C 21 FC60C 1600 45.0 33.2 13.00 11.00 MA20D 24 FC/MC60D 1600 45.0 33.2 13.00 11.00 MA20D 24 FC/MC62D 1600 45.0 33.2 13.00 11.00

13 SEER HP WITH MV - VARIABLE SPEED

MV12B 17 FC/MC18B 600 18.0 13.3 14.00 12.00 MV12B 17 FC/MC24B 600 18.0 13.4 14.00 12.00 MV12B 17 FC/MC30B 600 18.0 13.4 14.00 12.00 MV12B 17 FC/MC24B 800 23.0 17.4 14.00 12.00 MV12B 17 FC/MC30B 800 23.0 17.4 14.00 12.00 MV12B 17 FC/MC35B 800 23.0 17.4 14.00 12.00 MV12B 17 FC/MC35B 1000 29.0 21.8 14.00 12.00 MV16C 21 FC/MC35C 1000 29.0 22.0 14.00 12.00 MV12B 17 FC/MC43B 1000 29.0 21.8 14.00 12.00 MV16C 21 FC/MC43C 1000 29.0 22.0 14.00 12.00 MV12B 17 FC/MC43B 1200 35.0 26.2 14.00 12.00 MV16C 21 FC/MC43C 1200 35.0 26.4 14.00 12.00 MV16C 21 FC/MC48C 1200 35.0 26.4 14.00 12.00 MV16C 21 FC60C 1200 35.0 26.4 14.00 12.00 MV12D 24 FC/MC48D 1200 35.0 26.4 14.00 12.00 MV12D 24 FC/MC60D 1200 35.0 26.4 14.00 12.00 MV16C 21 FC/MC48C 1400 41.0 29.4 13.85 11.00 MV16C 21 FC/MC48C 1400 41.0 29.4 13.85 11.00 MV20D 24 FC/MC48D 1400 41.0 29.4 13.85 11.00 MV20D 24 FC/MC60D 1400 41.0 29.4 13.85 11.00 MV16C 21 FC60C 1200 45.0 33.2 13.25 11.00 MV20D 24 FC/MC60D 1600 46.0 33.8 13.25 11.00 MV20D 24 FC/MC62D 1600 45.0 33.6 13.30 11.00

COIL

MODEL

13 SEER HP WITH MA

RATED

CFM

TOTAL SENS.

COOLING

NET MBH

SEER EER

Johnson Controls Unitary Products 5

365147-YTG-C-0608

COOLING CAPACITY - With Air Handler Coils (Continued)

UNIT

MODEL

AIR HANDLER

MODEL W

COIL

MODEL

RATED

CFM

TOTAL SENS.

13 SEER HP WITH AV / SV / F*FV - VARIABLE SPEED

THGD18S21S1 AV24 17 – 565 18.0 13.4 14.00 12.00 THGD24S21S1 AV24 17 – 770 23.0 17.5 14.00 12.00 THGD30S21S1 AV36 21 – 1015 29.0 22.0 14.00 12.00

THGD36S21S1

AV36 21 – 1270 35.0 26.2 14.00 12.00 AV/SV48 24 – 1270 35.0 26.2 14.00 12.00 AV/SV48 24 – 1415 41.0 29.4 13.85 11.00

THGD42S21S1

AV/SV60 24 – 1410 41.0 29.4 13.85 11.00 F4FV060 24 – 1410 41.0 29.4 13.85 11.00 AV/SV48 24 – 1610 46.0 33.8 13.25 11.00

THGD48S21S1

AV/SV60 24 – 1655 46.0 33.6 13.25 11.00 F4FV060 24 – 1655 46.0 33.6 13.30 11.00

13 SEER HP WITH AHP / SHP / F*FP

AHP18 17 – 650 18.0 12.9 13.00 11.00

THGD18S21S1

AHP24 17 – 655 18.0 13.0 13.00 11.00

F4FP024 17 – 655 18.0 13.0 13.00 11.00

AHP24 17 – 830 23.0 16.9 13.00 11.00

THGD24S21S1

AHP30 17 – 795 23.0 16.8 13.00 11.00

F4FP030 17 – 795 23.0 16.8 13.00 11.00

AHP30 17 – 1015 29.0 21.2 13.00 11.00

THGD30S21S1

AHP36 21 – 1040 29.0 21.2 13.00 11.00

F4FP040 21 – 1040 29.0 21.2 13.00 11.00

AHP36 21 – 1235 35.0 25.6 13.00 11.00 AHP42 21 – 1255 35.0 25.6 13.00 11.00

THGD36S21S1

AHP/SHP60 24 – 1270 35.0 26.2 14.00 12.00

F4FP045 24 – 1200 35.0 25.6 13.00 11.00 F5FP048 24 – 1200 35.0 26.2 14.00 12.00 F5FP060 24 – 1200 35.0 26.2 14.00 12.00

AHP/SHP48 24 – 1400 40.0 29.0 13.00 11.00 AHP/SHP60 24 – 1400 41.0 29.4 13.85 11.00

THGD42S21S1

F4FP045 24 – 1400 40.0 29.0 13.00 11.00 F5FP048 24 – 1400 41.0 29.4 13.85 11.00 F5FP060 24 – 1400 41.0 29.4 13.85 11.00

AHP/SHP48 24 – 1600 45.0 33.2 13.00 11.00

THGD48S21S1

AHP/SHP60 24 – 1600 46.0 33.6 13.30 11.00

F5FP060 24 – 1600 46.0 33.6 13.30 11.00

Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210. Cooling MBH based on 80°F entering air temperature, 50% RH, and rated air flow. EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at 95°F outd oor ambient divided by the total electric power in watt-hours at those conditions. SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power input in watt-hours during the same period.

COOLING

NET MBH

SEER EER

1. MC coils available with a factory installed horizontal drain pan. See price pages for specific model number. — = Not applicable.

6 Johnson Controls Unitary Products

365147-YTG-C-0608

COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils

FURNACE**

UNIT MODEL

THGD18S21S1

THGD24S21S1

THGD30S21S1

THGD36S21S1

THGD42S21S1

THGD48S21S1

THGD60S21S1 1600 - 2000 24 FC/MC62 1800 55.0 40.0 13.00 11.00

1. Requires a 2FD06700224 Blower Time Delay unless a standard furnace is equipped with one. ** Refer to Quick Selection Chart for specific furnace match-up.

CFM RANGE

(Min.-max.)

450 - 750 14,17 FC/MC/PC/UC18 600 18.0 12.9 13.00 11.00 450 - 750 14,17 FC/MC/PC/UC24 600 18.0 12.9 13.00 11.00 450 - 750 14,17 FC/MC/PC/UC30 600 18.0 12.9 13.00 11.00

450 - 750 14 HC18 600 18.0 12.9 13.00 11.00 600 - 1000 14,17 FC/MC/PC/UC24 800 23.0 16.8 13.00 11.00 600 - 1000 14,17 FC/MC/PC/UC30 800 23.0 16.8 13.00 11.00 600 - 1000 14 FC/MC/PC/UC32 800 23.0 16.8 13.00 11.00 600 - 1000 17,21 FC/MC/PC/UC35 800 23.0 16.8 13.00 11.00 600 - 1000 14 HC30 800 23.0 16.8 13.00 11.00 600 - 1000 17 HC36 800 23.0 16.8 13.00 11.00 600 - 1000 – HD24 800 23.0 16.8 13.00 11.00 600 - 1000 19 MH24S 800 23.0 16.8 13.00 11.00 600 - 1000 19 MH30S 800 23.0 16.8 13.00 11.00 800 - 1200 14 FC/MC/PC/UC32 1000 29.0 21.2 13.00 11.00 800 - 1200 17,21 FC/MC/PC/UC35 1000 29.0 21.2 13.00 11.00 800 - 1200 14 FC/MC/PC/UC37 1000 29.0 21.2 13.00 11.00 800 - 1200 17,21 FC/MC/PC/UC43 1000 29.0 21.2 13.00 11.00 800 - 1200 17 HC36 1000 29.0 21.2 13.00 11.00 800 - 1200 21 HC42 1000 29.0 21.2 13.00 11.00 800 - 1200 – HD36 1000 29.0 21.2 13.00 11.00 800 - 1200 19 MH24S 1000 29.0 21.2 13.00 11.00 800 - 1200 19 MH30S 1000 29.0 21.2 13.00 11.00

1000 - 1400 14 FC/MC/PC/UC37 1200 35.0 25.6 13.00 11.00 1000 - 1400 17,21 FC/MC/PC/UC43 1200 35.0 25.6 13.00 11.00 1000 - 1400 21,24 FC/MC/PC/UC48 1200 35.0 25.6 13.00 11.00 1000 - 1400 21,24 FC/MC/PC/UC60 1200 35.0 25.6 13.00 11.00 1000 - 1400 21 HC42 1200 35.0 25.6 13.00 11.00 1000 - 1400 24 HC60 1200 35.0 25.6 13.00 11.00 1000 - 1400 – HD48 1200 35.0 25.6 13.00 11.00 1000 - 1400 – HD60 1200 35.0 25.6 13.00 11.00 1200 - 1600 21,24 FC/MC/PC/UC48 1400 40.0 28.8 13.00 11.00 1200 - 1600 21,24 FC/MC/PC/UC60 1400 40.0 28.8 13.00 11.00 1200 - 1600 24 HC60 1400 40.0 28.8 13.00 11.00 1200 - 1600 – HD60 1400 40.0 28.8 13.00 11.00 1400 - 1800 21,24 FC/MC/PC/UC60 1600 45.0 33.2 13.00 11.00 1400 - 1800 24 FC/MC62 1600 45.0 33.2 13.00 11.00 1400 - 1800 24 HC60 1600 45.0 33.2 13.00 11.00 1400 - 1800 – HD60 1600 45.0 33.2 13.00 11.00

COIL

MODEL

RATED

CFM

TOTAL SENS.

COOLING

NET MBH

SEER

EER

Johnson Controls Unitary Products 7

365147-YTG-C-0608

COOLING CAPACITY - With Variable Speed Furnaces

UNIT MODEL

THGD18S21S1

THGD24S21S1

THGD30S21S1

For Notes See Page 9.

VARIABLE SPEED

FURNACE MODEL

13 SEER HP WITH VARIABLE SPEED FURNACES

PV8*A12 FC/MC/PC/UC18A 14 600 18.0 13.4 14.00 12.00 PV9*A12 FC/MC/PC/UC18A 14 600 18.0 13.3 14.00 12.00

P(C,V)9*B12 FC/MC/PC/UC18B 17 600 18.0 13.4 14.00 12.00

PV8*A12 FC/MC/PC/UC24A 14 600 18.0 13.4 14.00 12.00 PV9*A12 FC/MC/PC/UC24A 14 600 18.0 13.3 14.00 12.00

P(C,V)9*B12 FC/MC/PC/UC24B 17 600 18.0 13.4 14.00 12.00

PV8*A12 FC/MC/PC/UC30A 14 600 18.0 13.4 14.00 12.00 PV9*A12 FC/MC/PC/UC30A 14 600 18.0 13.3 14.00 12.00

P(C,V)9*B12 FC/MC/PC/UC30B 17 600 18.0 13.4 14.00 12.00

PV8*A12 HC18 14 600 18.0 13.4 14.00 12.00 PV9*A12 HC18 14 600 18.0 13.3 14.00 12.00 PV8*A12 FC/MC/PC/UC24A 14 800 23.0 17.3 14.00 12.00 PV9*A12 FC/MC/PC/UC24A 14 800 23.0 17.3 14.00 12.00

P(C,V)9*B12 FC/MC/PC/UC24B 17 800 23.0 17.3 14.00 12.00

PV8*A12 FC/MC/PC/UC30A 14 800 23.0 17.3 14.00 12.00 PV9*A12 FC/MC/PC/UC30A 14 800 23.0 17.3 14.00 12.00

P(C,V)9*B12 FC/MC/PC/UC30B 17 800 23.0 17.3 14.00 12.00

PV8*A12 FC/MC/PC/UC32A 14 800 23.0 17.3 14.00 12.00 PV9*A12 FC/MC/PC/UC32A 14 800 23.0 17.3 14.00 12.00

P(C,V)9*B12 FC/MC/PC/UC35B 17 800 23.0 17.3 14.00 12.00

PV8*A12 HC30 14 800 23.0 17.3 14.00 12.00 PV9*A12 HC30 14 800 23.0 17.3 14.00 12.00

P(C,V)9*B12 HC36 17 800 23.0 17.3 14.00 12.00

PV8*A12 FC/MC/PC/UC32A 14 1000 29.0 21.6 14.00 12.00 PV9*A12 FC/MC/PC/UC32A 14 1000 29.0 21.6 14.00 12.00 PV8*B16 FC/MC/PC/UC35B 17 1000 29.0 22.0 14.00 12.00 PV8*C16 FC/MC/PC/UC35C 21 1000 29.0 22.0 14.00 12.00 PV8*C20 FC/MC/PC/UC35C 21 1120 29.0 21.6 14.00 12.00

P(C,V)9*B12 FC/MC/PC/UC35B 17 1000 29.0 21.6 14.00 12.00

P(C,V)9*C16 FC/MC/PC/UC35C 21 1010 29.0 21.8 14.00 12.00

PV8*A12 FC/MC/PC/UC37A 14 1000 29.0 21.6 14.00 12.00 PV9*A12 FC/MC/PC/UC37A 14 1000 29.0 21.6 14.00 12.00 PV8*B16 FC/MC/PC/UC43B 17 1000 29.0 22.0 14.00 12.00 PV8*C16 FC/MC/PC/UC43C 21 1000 29.0 22.0 14.00 12.00 PV8*C20 FC/MC/PC/UC43C 21 1120 29.0 21.6 14.00 12.00

P(C,V)9*B12 FC/MC/PC/UC43B 17 1000 29.0 21.6 14.00 12.00

P(C,V)9*C16 FC/MC/PC/UC43C 21 1010 29.0 21.8 14.00 12.00

PV8*B16 HC36 17 1000 29.0 22.0 14.00 12.00

P(C,V)9*B12 HC36 17 1000 29.0 21.6 14.00 12.00

PV8*C16 HC42 21 1000 29.0 22.0 14.00 12.00 PV8*C20 HC42 21 1120 29.0 21.6 14.00 12.00

P(C,V)9*C16 HC42 21 1010 29.0 21.8 14.00 12.00

COIL

MODEL

COOLING

RATED

CFM

Net MBH

TOTAL SENS.

SEER EER

8 Johnson Controls Unitary Products

COOLING CAP ACITY - With Variable Speed Furnaces (Continued)

UNIT MODEL

THGD36S21S1

THGD42S21S1

THGD48S21S1

THGD60S21S1

1. MC coils available with a factory installed horizontal drain pan. See price pages for specific model number.

2. Variable speed furnaces have B.O.D (Blower on Delay) standard.

VARIABLE SPEED

FURNACE MODEL

13 SEER HP WITH VARIABLE SPEED FURNACES

PV8*A12 FC/MC/PC/UC37A 14 1200 35.0 26.0 13.55 11.00 PV9*A12 FC/MC/PC/UC37A 14 1200 35.0 25.8 13.25 11.00

PV8*B16 FC/MC/PC/UC43B 17 1200 35.0 26.2 14.00 12.00 PV8*C16 FC/MC/PC/UC43C 21 1200 35.0 26.2 14.00 12.00 PV8*C20 FC/MC/PC/UC43C 21 1200 35.0 26.0 13.85 12.00

P(C,V)9*B12 FC/MC/PC/UC43B 17 1200 35.0 26.0 13.70 12.00 P(C,V)9*C16 FC/MC/PC/UC43C 21 1175 35.0 26.2 14.00 12.00 P(C,V)9*C20 FC/MC/PC/UC43C 21 1200 35.0 26.2 14.00 12.00

PV8*C16 FC/MC/PC/UC48C 21 1200 35.0 26.4 14.00 12.00

PV8*C20 FC/MC/PC/UC48C 21 1200 35.0 26.0 13.90 12.00 P(C,V)9*C16 FC/MC/PC/UC48C 21 1175 35.0 26.2 14.00 12.00 P(C,V)9*C20 FC/MC/PC/UC48C 21 1200 35.0 26.2 14.00 12.00 P(C,V)9*D20 FC/MC/PC/UC48D 24 1200 35.0 26.2 14.00 12.00

PV8*C16 HC42 21 1200 35.0 26.2 14.00 12.00

PV8*C20 HC42 21 1200 35.0 26.0 13.90 12.00 P(C,V)9*C16 HC42 21 1175 35.0 26.2 14.00 12.00 P(C,V)9*C20 HC42 21 1200 35.0 26.2 14.00 12.00

PV8*C16 FC/MC/PC/UC48C 21 1400 40.0 29.2 13.45 11.00

PV8*C20 FC/MC/PC/UC48C 21 1400 41.0 29.2 13.55 11.00 P(C,V)9*C16 FC/MC/PC/UC48C 21 1415 40.0 29.0 13.25 11.00 P(C,V)9*C20 FC/MC/PC/UC48C 21 1400 40.0 29.2 13.45 11.00 P(C,V)9*D20 FC/MC/PC/UC48D 24 1400 40.0 29.0 13.35 11.00

PV8*C16 FC/PC/UC60C 21 1400 41.0 29.2 13.45 11.00

PV8*C20 FC/PC/UC60C 21 1400 41.0 29.2 13.60 11.00 P(C,V)9*C16 FC/PC/UC60C 21 1415 40.0 29.0 13.25 11.00 P(C,V)9*C20 FC/PC/UC60C 21 1400 41.0 29.2 13.45 11.00 P(C,V)9*D20 FC/MC/PC/UC60D 24 1400 40.0 29.0 13.40 11.00

PV8*C16 FC/PC/UC60C 21 1500 45.0 33.4 13.25 11.00

PV8*C20 FC/PC/UC60C 21 1610 45.0 33.4 13.25 11.00 P(C,V)9*C16 FC/PC/UC60C 21 1600 45.0 33.2 13.25 11.00 P(C,V)9*C20 FC/PC/UC60C 21 1600 45.0 33.4 13.25 11.00 P(C,V)9*D20 FC/MC/PC/UC60D 24 1600 45.0 33.4 13.25 11.00

PV8*C20 FC/MC62D 24 1610 45.0 33.4 13.25 11.00 P(C,V)9*C20 FC/MC62D 24 1600 45.0 33.4 13.25 11.00 P(C,V)9*D20 FC/MC62D 24 1600 45.0 33.4 13.25 11.00

PV8*C20 FC/MC62D 24 1730 55.0 40.0 13.50 11.00 P(C,V)9*C20 FC/MC62D 24 1620 54.0 40.5 13.50 11.00 P(C,V)9*D20 FC/MC62D 24 1620 54.0 40.5 13.50 11.00

COIL

MODEL

RATED

CFM

TOTAL SENS.

COOLING

Net MBH

365147-YTG-C-0608

SEER EER

Johnson Controls Unitary Products 9

+ 21 hidden pages