York H-RE024 User Manual

036-21315-001 Rev. A (0502)

®

TECHNICAL GUIDE

SPLIT-SYSTEM
AIR CONDITIONERS

14 SEER

MODELS:
H*RE024 THRU 060
(2 THRU 5 NOMINAL TONS)

O

T

A

R

D

I

E

I

A

F

S

I

T

R

C

E

O

C

R

E

R

U

T
C

A

F

U
N

A

M

C

E

A

CERTIFICATION APPLIES ONLY

WHEN THE COMPLETE

SYSTEM IS LISTED

Due to continuous product improvement, specifications
are subject to change without notice.

Visit us on the web at www.york.com for the most
up-to-date technical information.

Additional rating information can be found at
www.ari.org.

Y

R

A

T

I
N

U

R

E

Q

U

I

E

P

M

R

T

I

F

I

C

A

T

R

I

S

O

N

I

S

T

A

N

D

WITH ARI.

M

A

P

I

R

-

L

C

O

Y

N

I

D

I

N

T

G

I

O

N
I

W

N

I

G

T

H

T

F

N

O

S

N

O

I

T

0

C

E

1

2

D

R

A

LISTED

DESCRIPTION

The 14 SEER Series condensing unit is the outdoor part of a
versatile system of air conditioning. It is designed to be cus­tom-matched with one of UPG’s complete line of evaporator
sections, with each serving a specific function. Matching Air
Handlers are available for upflow, downflow, or horizontal
applications to provide a complete system. Electric Heaters
are available, if required. Add-On coils are available for use
with upflow, downflow, or horizontal furnaces and air han­dlers.

WARRANTY

5-year limited parts warranty.

10-year limited compressor warranty.

FEATURES

• QUALITY CONDENSER COILS - The coil is constructed
of copper tube and aluminum fins.

• PROTECTED COMPRESSOR - The compressor is inter­nally protected against high pressure and temperature.
This is accomplished by the simultaneous operation of
high pressure relief valve and a temperature sensor which
protects the compressor if undesirable operating condi­tions occur. A liquid line filter-drier further protects the
compressor.

• DURABLE FINISH - The cabinet is made of pre-painted
steel. The pre-treated galvanized steel provides a better
paint to steel bond, which resists corrosion and rust creep.
Special primer formulas and desert sand matted-textured
finish insure less fading when exposed to sunlight.

• LOWER INSTALLED COST - Installation time and costs
are reduced by easy power and control wiring connections.
Discharge line heat exchanger knockouts are provided, if
required. Available in sweat connect models only. The unit
contains enough refrigerant for matching indoor coils and
15 feet of interconnecting piping. The small base dimen­sion means less space is required on the ground or roof.

• TOP DISCHARGE - The warm air from the top mounted
fan is blown up away from the structure and any landscap­ing. This allows compact location on multi-unit applica­tions.

• LOW OPERATING SOUND LEVEL - The upward air flow
carries the normal operating noise away from the living
area. The rigid top panel effectively isolates any motor
sound. Isolator mounted compressor and the rippled fins of
the condenser coil muffle the normal fan motor and com­pressor operating sounds.

• LOW MAINTENANCE - Long life permanently lubricated
motor-bearings need no annual servicing.

• EASY SERVICE ACCESS - Fully exposed refrigerant con­nections, a single panel covering the electrical controls,
and the molex plug in the control box connecting the con­denser fan make for easy servicing of the unit.

• SECURED SERVICE VALVES - Secured re-usable ser-
vice valves are provided on both the liquid and vapor
sweat connections for ease of evacuating and charging.

• U.L. and C.U.L. listed - approved for outdoor application.

Certified in accordance with the Unitary Small Equipment cer­tification program, which is based on ARI Standard 210/240.

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

036-21315-001 Rev. A (0502)

h

.

Physical and Electrical Data

MODEL

Unit Supply Voltage 208 / 230 - 1 – 60

Normal Voltage Range
Minimum Circuit Ampacity 12.1 14.9 18.1 17.8 20.6 31.8

Max Overcurrent Device Amps

Compressor Type

Compressor Amps

Crankcase Heater No No No No No No
Fan Motor Amps Rated Load .5 1.3 1.3 1.3 1.3 1.4
Fan Diameter Inches 22 22 22 24 24 24

Fan Motor

Coil

Liquid Line OD 3/8 3/8 3/8 3/8 3/8 3/8
Vapor Line OD 7/8 7/8 7/8 1 1/8 1 1/8 1 1/8

Unit Charge (Lbs - Oz)
Charge Per Foot, oz. 0.70 0.70 0.70 0.76 0.76 0.76
Operating Weight Lbs 209 228 219 240 264 270

1. Rated in accordance with ARI Standard 110, utilization range “A”.

2. Dual element fuses or HACR circuit breaker.

3. All scrolls listed with superscript “B” are Bristol scrolls. All scrolls listed with superscripts “C” are Copeland scrolls.

4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15
feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.

1

2

3

Rated Load 9.3 10.9 13.5 13.2 15.5 24.3
Locked Rotor 57 64 73 95 109 150

Rated HP 1/15 1/4 1/4 1/4 1/4 1/3
Nominal RPM 830 825 825 825 825 1100
Nominal CFM 2,260 3,300 3,300 3,300 3,300 3,500
Face Area Sq Ft 19.65 23.58 23.58 22.5 27.0 27.0
Rows Deep 1 1 1 2 2 2
Fin /Inch 18 18 18 18 18 18

4

H1RE024S06 H1RE030S06 H1RE036S06 H2RE042S06 H2RE048S06 H2RE060S06

187 to 252

20 20 25 30 35 50

Inertia Inertia

Scroll

C

Scroll

C

Scroll

C

Scroll

8 - 0 9 - 14 9 - 6 14 - 0 14 - 3 15 - 13

B

All dimensions are in inches. They are subject to change wit
out notice. Certified dimensions will be provided upon request

C

Unit

Model

Dimensions

(Inches)

Refrigerant

Connection

Line Size

A B C Liquid Vapor

024 33 37 27

A

036 39 37 27
042 32 43 32

3/8

7/8030 39 37 27

1-1/8048 38 43 32

060 38 43 32

1. Included Fan Guard
* Reducer Fan Guard

B

2 Unitary Products Group

036-21315-001 Rev. A (0502)

COOLING CAPACITY - With Air Handler Coils

COOLING

SEER

W/O TXV

SEER

+ TXV

3

UNIT MODEL

MODEL

AIR HANDLER

ELECTRIC

HEAT KW

2

W

COIL

MODEL

1

RATED

CFM

NET MBH

TOTAL SENS.

1 PH 14 SEER AC WITH N-AH / G2FD

H1RE024S06 N1AHB0806 2,5,8,10 17 G2FD036S17 800 25.2 18.1 - 14.00 12.35

H1RE030S06 N1AHB1206 5,8,10,15,19 17 G2FD036S17 1000 28.8 20.7 - 13.10 11.80

N1AHB1206 5,8,10,15,19 17 G2FD036S17 1200 34.0 24.5 - 13.35 11.80

H1RE036S06

N1AHB1206 5,8,10,15,19 17 G2FD046S17 1200 35.0 25.6 - 14.00 12.20

N1AHD1406 5,8,10,15 24 G2FD048S24 1200 35.4 25.7 - 14.00 12.50

N1AHD1406 5,8,10,15 24 G2FD060S24 1200 36.0 26.1 - 14.20 12.80

N1AHC1606 5,8,10,15,20 21 G2FD042S21 1400 39.0 28.2 - 13.25 11.35

H2RE042S06

N1AHC1606 5,8,10,15,20 21 G2FD048S21 1400 39.5 28.9 - 13.50 11.60

N1AHD1406 5,8,10,15 24 G2FD060S24 1400 40.5 29.6 - 14.00 12.00

H2RE048S06

H2RE060S06

N1AHD2006 8,10,15,20,25,30 24 G2FD060S24 1600 46.5 33.9 - 13.85 11.80

N1AHD2006 8,10,15,20,25,30 24 G2FD061H24 1600 47.0 34.3 - 14.00 11.90

N1AHD2006 8,10,15,20,25,30 24 G2FD060S24 1900 53.5 37.1 - 13.50 12.00

N1AHD2006 8,10,15,20,25,30 24 G2FD061H24 2050 54.5 39.1 - 13.50 12.10

1 PH 14 SEER AC / N1VS - VARIABLE SPEED

H1RE024S06

H1RE030S06

H1RE036S06

N1VSB12 10,15,18 17 G2FD036S17 870 25.6 18.1 - 15.00 13.85

N1VSB12 10,15,18 17 G2FD046S17 870 26.2 18.9 - 15.50 14.15

N1VSB12 10,15,18 17 G2FD036S17 1000 29.4 20.7 - 14.50 12.95

N1VSB12 10,15,18 17 G2FD046S17 1070 30.0 21.6 - 15.35 13.60

N1VSB12 10,15,18 17 G2FD046S17 1250 35.2 25.6 - 14.00 12.40

N1VSC16 10,15,18 21 G2FD048S21 1285 36.0 25.7 - 15.00 13.60

N1VSC16 10,15,18 21 G2FD048S21 1420 40.5 28.9 - 14.50 12.50

H2RE042S06

N1VSC16 10,15,18 21 G2FD048S21 1420 40.5 28.9 - 14.50 12.50

N1VSD20 10,15,18,30 24 G2FD060S24 1420 41.5 29.6 - 15.50 13.20

H2RE048S06

H2RE060S06

H1RE024S06

H1RE030S06

N1VSC16 10,15,18 21 G2FD048S21 1590 46.0 33.2 - 14.30 12.20

N1VSD20 10,15,18,30 24 G2FD060S24 1600 47.0 33.9 - 14.65 12.40

N1VSD20 8,10,15,20,25,30 24 G2FD060S24 1780 53.5 36.3 - 13.75 12.35

N1VSD20 8,10,15,20,25,30 24 G2FD061H24 1780 54.5 37.0 - 14.00 12.60

1 PH 14 SEER AC / F2RP / RC / FP / FC / FV

4,5

F2RP/FP036 5,8,10,15,19 21 - 800 25.0 18.0 - 13.80 12.30

F2FP040 5,8,10,15 21 - 800 25.4 17.4 - 14.00 12.75

F2RP/FP036 5,8,10,15,19 21 - 1000 29.8 21.5 - 13.85 12.40

F2FP045 5,8,10,15 24 - 1000 30.6 21.5 - 14.00 12.70

F2RP/FP036 5,8,10,15,19 21 - 1200 34.4 24.8 - 13.50 12.10

H1RE036S06

F2RP/FP042 5,8,10,15 21 - 1200 34.4 24.8 - 13.30 11.90

F2FP045 5,8,10,15 24 - 1200 36.0 25.5 - 14.00 12.65

H2RE042S06

H2RE048S06

H2RE060S06

Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210.
Cooling MBH based on 80°F entering air temperature, 50% RH, and rated air flow.
KW includes compressor, outdoor fan and indoor blower motor watts. Add-on coils include 365 watts/1000 CFM for blower motor.
EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at a 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions.
SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power
input in watt-hours during the same period.

F2FP045 5,8,10,15 24 - 1400 40.5 29.8 - 14.00 12.00

F2FP048 5,8,10,15,20,25 24 - 1400 39.5 28.9 - 13.25 11.30

F2FP060 5,8,10,15,20,25 24 - 1600 46.0 33.4 - 13.00 11.25

F2FV060 8,10,15,20,25 24 - 1625 47.5 34.9 - 15.50 13.20

F2FP060 10,15,20,25 24 -- 1900 53.0 36.7 - 13.00 11.60

F2FV060 10,15,20,25 24 -- 1900 53.5 36.3 - 13.75 12.35

EER

1. G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number.

2. Single phase units require single phase 2HK heaters.

3. TXV = Use 1TV700 Series Kit.

4. To meet R=4.2 insulation requirements, substitute F2FP for F2RP, and F2FC for F2RC

5. FG8, FG9, and FL8 furnaces and F2RP / F2RC air handlers have B.O.D (Blower on Delay) standard.

- = Not applicable

. models. All ratings remain the same.

Unitary Products Group 3

036-21315-001 Rev. A (0502)

COOLING CAPACITY - Upflow, Downflow, & Horizontal Furnaces and Coils

UNIT MODEL

H1RE024S06

H1RE030S06

H1RE036S06

H2RE042S06

H2RE048S06

For Notes See Page 5.

FURNACE**

CFM RANGE

(MIN.-MAX.)

700
900

875

112 5

1050
1350

1225
1575

1400
1800

W

14 G1FA036S14 800 25.0 18.0 13.85 - 12.30

17,21 G1FA036S17,21 800 24.8 17.9 13.85 - 12.20

- G1HD036 800 25.0 18.1 14.00 - 12.35
17 G1NA036S17L 800 24.0 16.6 13.50 - 12.00
21 G1NA048S21D 800 24.0 16.6 13.50 - 12.00
14 G1UA036S14 800 25.0 18.0 13.85 - 12.30

17,21 G1UA036S17,21 800 24.8 17.9 13.85 - 12.20

17 G2FD030S17 800 24.8 17.9 13.85 - 12.20
14 G2FD035S14 800 24.8 17.9 13.85 - 12.20
17 G2FD036S17 800 25.2 18.1 14.00 - 12.35
21 G2FD036S21 800 25.2 18.1 14.00 - 12.45
14 G1FA036S14 1000 28.4 20.0 13.00 - 11.75

17,21 G1FA036S17,21 1000 28.4 20.0 13.00 - 11.65
21,24 G1FA048S21,24 1000 30.0 21.8 14.00 - 12.40

- G1HD048 1000 30.0 21.5 14.00 - 12.40
17 G1NA036S17L 1000 29.0 20.0 - 13.50 11.95
24 G1NA042S24W 1000 29.0 20.7 - 14.00 12.00
21 G1NA048S21D 1000 29.0 20.0 - 13.50 11.95
14 G1UA036S14 1000 28.4 20.0 13.00 - 11.75

17,21 G1UA036S17,21 1000 28.4 20.0 13.00 - 11.65
21,24 G1UA048S21,24 1000 30.0 21.8 14.00 - 12.40

17 G2FD030S17 1000 28.4 20.4 13.00 - 11.65
17 G2FD036S17 1000 28.8 20.7 13.10 - 11.80
21 G2FD036S21 1000 28.8 21.0 13.10 - 12.10

21,24 G2FD048S21,24 1000 30.2 21.8 - 14.00 12.50
21,24 G1FA048S21,24 1200 35.2 25.3 14.00 - 12.30

- G1HD048 1200 34.8 25.0 13.75 - 12.30
17 G1NA036S17L 1200 33.0 23.4 - 13.00 11.30
24 G1NA042S24W 1200 34.6 25.0 - 14.00 12.00
21 G1NA048S21D 1200 33.0 23.4 - 13.00 11.30

21,24 G1UA048S21,24 1200 35.2 25.3 14.00 - 12.30

17 G2FD036S17 1200 34.0 24.5 13.35 - 11.80
21 G2FD036S21 1200 34.0 24.8 13.35 - 12.05
21 G2FD042S21 1200 34.8 25.4 13.70 - 12.10
17 G2FD046S17 1200 35.0 25.6 14.00 - 12.20

21,24 G2FD048S21,24 1200 35.2 25.7 14.00 - 12.45
21,24 G1FA048S21,24 1400 39.0 28.4 - 13.50 11.45
21,24 G1FA060S21,24 1400 40.5 29.6 - 14.00 11.80

- G1HD048 1400 39.0 28.4 - 13.25 11.50
24 G1NA042S24W 1400 40.5 29.5 - 14.00 11.75
21 G1NA048S21D 1400 39.0 27.3 - 13.00 11.50

21,24 G1UA048S21,24 1400 39.0 28.4 - 13.50 11.45
21,24 G1UA060S21,24 1400 40.5 29.6 - 14.00 11.80

21 G2FD042S21 1400 39.0 28.2 - 13.25 11.35
17 G2FD046S17 1400 39.0 28.6 - 13.50 11.45

21,24 G2FD048S21,24 1400 39.5 28.9 - 13.50 11.60

24 G2FD060S24 1400 40.5 29.6 - 14.00 11.80

21,24 G1FA048S21,24 1600 45.0 32.6 - 13.40 11.50
21,24 G1FA060S21,24 1600 46.5 33.9 - 13.85 11.80

- G1HD048 1600 45.0 32.4 - 13.25 11.45
24 G1NA042S24W 1500 46.5 32.8 - 14.00 11.85
21 G1NA048S21D 1400 44.0 29.0 - 13.00 11.50

21,24 G1UA048S21,24 1600 45.0 32.6 - 13.40 11.50
21,24 G1UA060S21,24 1600 46.5 33.9 - 13.85 11.80
21,24 G2FD048S21,24 1600 45.5 33.2 - 13.50 11.60

24 G2FD060S24 1600 46.5 33.9 - 13.85 11.80
24 G2FD061H24 1600 47.0 34.3 - 14.00 11.90

COIL

MODEL

RATED

CFM

NET MBH

TOTAL SENS.

COOLING

SEER + TXV

W/O TDR

SEER + TXV

+ TDR*

1

EER

4 Unitary Products Group

036-21315-001 Rev. A (0502)

COOLING CAPACITY - Upflow, Downflow, & Horizontal Furnaces and Coils (Continued)

COOLING

SEER + TXV

W/O TDR

UNIT MODEL

FURNACE**

CFM RANGE

(MIN.-MAX.)

W

COIL

MODEL

RATED

CFM

TOTAL SENS.

21,24 G1FA060S21,24 1900 53.5 37.1 - 13.25 12.00

24 G2FD060S24 1900 53.5 37.1 - 13.25 12.00

H2RE060S06

1650
2150

24 G2FD061H24 2050 54.5 39.1 - 13.25 12.10

- G1HD060 1900 52.5 36.0 - 13.00 11.75

24 G1NA060S24T 1900 53.0 35.9 - 13.00 11.90

21,24 G1UA060S21,24 1900 53.5 37.1 - 13.25 12.00

1. TXV = Use 1TV700 Series Kit.

* Requires a 2FD Blower Time Delay unless a standard furnace is equipped with one.
**

Refer to Quick Selection Chart for specific furnace match-up.

NET MBH

COOLING CAPACITY - With Variable Speed Furnaces

COOLING

SEER

W/O TXV

3

UNIT MODEL

VARIABLE SPEED
FURNACE MODEL

COIL MODEL

1

W

RATED

CFM

NET MBH

TOTAL SENS.

1 PH 14 SEER AC / P1DU / P1XD / P1XU - VARIABLE SPEED

P1DUA12V G1FA036S14 14 870 25.4 18.0 - 15.00 13.60
P1DUA12V G1UA036S14 14 870 25.4 18.0 - 15.00 13.60
P1DUA12V G2FD035S14 14 870 25.2 17.9 - 15.00 13.50

H1RE024S06

P1XDB12V G2FD030S17 17 830 26.0 17.9 - 15.00 13.65
P1XUB12V G1FA036S17 17 870 25.4 18.0 - 15.50 13.75
P1XUB12V G1UA036S17 17 870 25.4 18.0 - 15.50 13.75
P1XUB12V G2FD030S17 17 870 25.4 17.9 - 15.50 13.75
P1XUB12V G2FD036S17 17 870 25.8 18.1 - 15.50 13.90
P1DUA12V G1FA036S14 14 1000 28.8 20.0 - 13.50 12.50
P1DUA12V G1UA036S14 14 1000 28.8 20.0 - 13.50 12.50

H1RE030S06

P1DUB16V G2FD036S17 17 1000 30.0 20.7 - 14.50 13.35
P1XDB12V G2FD036S17 17 1040 30.2 20.7 - 14.00 12.50
P1XUB12V G2FD036S17 17 1020 29.2 20.7 - 14.00 12.65
P1DUB16V G2FD036S17 17 1200 34.4 24.5 - 14.00 12.70
P1DUC20V G1FA048S21 21 1200 36.2 25.3 - 15.50 14.15
P1DUC20V G1UA048S21 21 1200 36.2 25.3 - 15.50 14.15

H1RE036S06

P1DUC20V G2FD036S21 21 1200 34.6 24.8 - 14.65 13.05
P1DUC20V G2FD048S21 21 1200 36.0 25.7 - 15.50 13.95
P1XDB12V G2FD036S17 17 1130 34.8 24.5 - 14.20 12.60
P1XDD20V G2FD048S24 24 1195 36.2 25.7 - 14.50 13.10
P1XUB12V G2FD036S17 17 1200 34.4 24.5 - 14.00 12.65
P1DUC20V G1FA048S21 21 1400 39.5 28.4 - 14.50 12.45
P1DUC20V G1FA060S21 21 1400 41.0 29.6 - 15.00 12.80
P1DUC20V G1UA048S21 21 1400 39.5 28.4 - 14.50 12.45
P1DUC20V G1UA060S21 21 1400 41.0 29.6 - 15.00 12.80

H2RE042S06

P1DUC20V G2FD042S21 21 1400 39.5 28.2 - 14.00 12.30
P1DUC20V G2FD048S21 21 1420 40.0 28.9 - 14.50 12.60
P1DUC20V G2FD048S21 21 1420 40.0 28.9 - 14.50 12.50
P1XDD20V G2FD048S24 24 1365 41.0 28.9 - 14.40 12.50
P1XDD20V G2FD060S24 24 1420 41.5 33.8 - 14.40 12.55
P1DUC20V G1FA060S21 21 1605 46.5 33.9 - 14.00 12.20

H2RE048S06

P1DUC20V G1UA060S21 21 1605 46.5 33.9 - 14.00 12.20
P1DUC20V G2FD048S21 21 1605 45.5 33.2 - 13.50 12.00
P1XDD20V G2FD060S24 24 1580 47.0 33.9 - 13.80 12.20
P1XDD20V G2FD060S24 24 1580 52.5 34.3 - 13.50 12.2
P1DUC20V G1FA060S21 21 1630 53.0 34.9 - 13.60 12.4
P1DUC20V G1UA060S21 21 1630 53.0 34.9 - 13.60 12.4
P1XUC20V G1FA060S21 21 1590 53.0 34.5 - 13.50 12.4

H2RE060S06

P1XUC20V G1UA060S21 21 1590 53.0 34.5 - 13.50 12.4
P1XUD20V G1FA060S24 24 1560 53.0 34.4 - 13.75 12.5
P1XUD20V G1UA060S24 24 1560 53.0 34.4 - 13.75 12.5
P1XUD20V G2FD060S24 24 1560 53.0 34.4 - 13.75 12.5
P1XUD20V G2FD061H24 24 1560 53.5 34.9 - 14.00 12.8

1. G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number.

2. TXV = Use 1TV700 Series Kit.

3. Variable speed furnaces have B.O.D (Blower on Delay) standard.

SEER + TXV

+ TDR*

SEER

+ TXV

1

EER

EER

2

Unitary Products Group 5

036-21315-001 Rev. A (0502)

COOLING PERFORMANCE

SUCT. T/P

MODEL

H1RE024S06

H1RE030S06

H1RE036S06

1. For condensing unit only. Does not include effect of evaporator motor power or heat.

2. Performance based on 15° superheat and 15° sub-cooling at condensing unit.

3. Sub-cooling in excess of 20° may result in excessively high condensing temperature with air on condenser above 115°. Maximum recommended
condensing temperature is 140°F.

@ COMPR.

TEMP. PSIG MBH KW MBH KW MBH KW TEMP. PSIG MBH KW MBH KW MBH KW

35 61.5 22.9 1.42 19.4 1.63 15.9 1.82

40 68.5 25.3 1.45 21.6 1.67 18.0 1.90 40 68.5 39.3 2.33 34.6 2.95 30.1 3.81

45 76.0 28.0 1.47 24.0 1.72 20.1 1.97 45 76.0 42.6 2.35 37.7 2.97 32.9 3.83

50 84.0 30.7 1.49 26.5 1.76 22.3 2.04 50 84.0 46.1 2.39 40.9 3.00 35.8 3.84

35 61.5 26.5 1.76 22.9 1.99 19.2 2.11

40 68.5 29.4 1.77 25.6 2.03 21.7 2.19 40 68.5 47.0 2.66 41.6 3.34 36.4 4.24

45 76.0 32.5 1.77 28.4 2.07 24.3 2.27 45 76.0 50.9 2.69 45.2 3.37 39.7 4.28

50 84.0 35.8 1.76 31.4 2.10 27.0 2.33 50 84.0 54.9 2.72 48.9 3.39 43.0 4.31

35 61.5 32.0 1.96 29.2 2.44 26.3 3.10

40 68.5 34.8 1.97 31.9 2.45 28.8 3.11 40 68.5 56.8 3.11 51.0 3.87 45.1 4.86

45 76.0 37.7 1.99 34.7 2.47 31.5 3.12 45 76.0 61.4 3.15 55.3 3.91 49.2 4.91

50 84.0 40.7 2.01 37.6 2.48 34.3 3.13 50 84.0 66.2 3.18 59.8 3.96 53.3 4.96

a. Increase capacity 1% for each 2° increase in sub-cooling.
b. Decrease capacity 1% for each 2° decrease in sub-cooling.

AIR TEMP ON CONDENSER

75×F 95×F 115×F 75×F 95×F 115×F

MODEL

H2RE042S06

H2RE048S06

H2RE060S06

SUCT. T/P

@ COMPR.

35 61.5 36.1 2.31 31.7 2.94 27.5 3.81

35 61.5 43.2 2.64 38.2 3.31 33.2 4.22

35 61.5 52.4 3.09 46.8 3.83 41.2 4.82

AIR TEMP ON CONDENSER

ACCESSORIES

Refer to Price Manual for specific model numbers.

Compressor Blanket - Designed to further reduce the nor­mal operating sound and is required to meet Canadian sound
levels for units of three tons and below.

Refer to Price Manual for specific model numbers.

Blower Time Delay - Available to increase efficiency when
installed. Installs on indoor section and maintains blower for
approximately one minute after cooling thermostat has been
satisfied.

TXV KIT - 1TV0700 series must be used to obtain system
performance. See Tabular Data Sheet for proper selection.

Room Thermostats - One of the following thermostat may
be used with these systems.

6TH07700124 - One Stage Heat / One Stage Cool, non-pro­grammable thermostat, manual changeover with automatic
fan on cooling or cooling and heating.

6ET07700324 - One Stage Heat / One Stage Cool, electronic
programmable (5 day/2 day) manual changeover.

SOUND RATINGS

SOUND

UNIT MODEL

024 76*
030 76*
036 76
042 76
048 76
060 80

* Includes Blanket

RATINGS

DECIBELS

6 Unitary Products Group

TYPICAL INSTALLATION

036-21315-001 Rev. A (0502)

60” OVERHEAD
CLEARANCE

10” CLEARANCE
COIL AREA

NOTE: ALL OUTDOOR WIRING
MUST BE WEATHERPROOF.

TYPICAL FIELD WIRING

ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES

POWER WIRING

208/230-1-60

MINIMUM 18” SERVICE ACCESS
CLEARANCE ON ONE SIDE

WEATHERPROOF
DISCONNECT
SWITCH

CONTROL ACCESS PANEL

24 VOLT CONTROL WIRING
MINIMUM 18 GA. WIRE
(NEC CLASS 2)

FURNACE OR AIR HANDLER TERMINAL BLOCK

THERMOSTAT

SEAL OPENING(S) WITH
PERMAGUM OR EQUIVALENT

CYRGW

TO FURNACE OR
AIR HANDLER
TERMINAL BLOCK

NEC CLASS 1 WIRING

NEC CLASS 2 WIRING

TO INDOOR COIL

POWER WIRING
CONTROL WIRING

FACTORY WIRING

GND.

LUG

CONTACTOR
TERMINALS

COIL

CONDENSING UNIT

ALL OUTDOOR WIRING MUST BE WEATHERPROOF. USE COPPER CONDUCTORS ONLY.

R

Y

ROOM THERMOSTAT

GW

*

*

TERMINAL W IS ONLY
REQUIRED ON SYSTEMS
WITH HEAT.

Unitary Products Group 7

036-21315-001 Rev. A (0502)

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. H1RE024S06

INDOOR COIL MODEL NO. F2RP/F2FP036

CONDENSER

ENTERING AIR

TEMPERATURE

75

85

95

105

115

125

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

ID CFM 1100 1250 1350

ID DB 85 80 75 70 85 80 75 70 85 80 75 70

ID WB 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 30.2 27.8 25.4 23.3 30.6 28.2 25.8 23.9 30.7 28.3 26.1 24.3

S.C. 17.7 17.8 17.9 17.9 19.1 19.0 19.2 18.9 19.8 19.7 19.8 19.1

K.W 1.751.741.721.701.811.791.781.771.831.821.811.79

T.C. 28.5 26.2 23.9 22.1 28.8 26.5 24.3 22.6 28.9 26.6 24.5 22.9

S.C. 17.3 17.3 17.4 17.4 18.5 18.5 18.6 17.8 19.3 19.2 19.2 18.1

K.W 1.871.851.821.801.931.911.891.871.961.941.921.90

T.C. 26.9 24.8 22.6 20.9 27.2 25.0 23.0 21.5 27.3 25.2 23.4 21.7

S.C. 16.9 16.8 17.0 16.5 18.1 18.0 18.0 16.9 18.8 18.8 18.4 17.1

K.W 2.02 1.99 1.96 1.93 2.08 2.05 2.02 2.00 2.11 2.08 2.06 2.03

T.C. 25.3 23.2 21.3 19.8 25.6 23.6 21.8 20.2 25.6 23.7 22.1 20.4

S.C. 16.4 16.3 16.4 15.6 17.6 17.5 17.2 15.9 18.4 18.2 17.4 16.1

K.W 2.182.142.102.072.252.212.172.142.282.242.212.17

T.C. 23.6 21.7 20.0 18.6 23.8 22.0 20.5 18.9 24.0 22.3 20.7 19.1

S.C. 15.9 15.8 15.8 14.6 17.1 16.9 16.1 14.9 17.9 17.6 16.3 15.1

K.W 2.362.312.262.212.422.372.332.292.462.412.372.32

T.C. 21.9 20.2 18.7 17.4 22.0 20.4 19.2 17.6 22.4 20.9 19.3 17.8

S.C. 15.4 15.3 15.2 13.6 16.6 16.3 15.0 13.9 17.4 17.0 15.2 14.1

K.W 2.542.482.422.352.592.532.492.442.642.582.532.47

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHB0806 G2FD036S17 1.01 1.01 1.00

N1VSB12 G2FD036S17 1.02 1.01 0.91

N1VSB12 G2FD046S17 1.05 1.05 0.91

F2FP040 1.02 0.97 0.98

F2RP/F2FP036 1.00 1.00 1.00

G1FA036S14 1.00 1.00 1.00

G1FA036S17,21 0.99 0.99 1.00

GFD030S17 0.99 0.99 1.00

GFD035S14 0.99 0.99 1.00

G1UA036S17,21 0.99 0.99 1.00

G2FD036S17 1.01 1.01 1.00

G2FD036S21 1.01 1.01 1.00

G1HD036S 1.00 1.01 0.98

G1NA036S17L 0.96 0.92 0.98

G1NA048S21D 0.96 0.92 0.99

G1UA036S14 1.00 1.00 1.00

T.C. S.C. KW

Variable Speed
Furnace

P1DUA12V G1FA036S14 1.02 1.00 0.92

P1DUA12V G1UA036S14 1.02 1.00 0.92

P1DUA12V G2FD035S14 1.01 0.99 0.92

P1XDB12V G2FD030S17 1.04 0.99 0.94

P1XUB12V G1FA036S17 1.02 1.00 0.91

P1XUB12V G1UA036S17 1.02 1.00 0.91

P1XUB12V G2FD030S17 1.02 0.99 0.91

P1XUB12V G2FD036S17 1.03 1.01 0.91

Coil

T.C. S.C. KW

8 Unitary Products Group

COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. H1RE030S06

INDOOR COIL MODEL NO. G1UA048S21, 24

CONDENSER

ENTERING AIR

TEMPERATURE

75

85

95

105

115

125

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

ID CFM 800 1000 1200

ID DB 85 80 75 70 85 80 75 70 85 80 75 70

ID WB 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 35.9 32.8 30.2 27.0 36.6 33.5 30.9 27.7 36.9 33.8 31.4 28.1

S.C. 21.2 21.2 20.4 21.4 22.8 22.9 22.0 23.1 23.9 23.9 23.1 24.2

K.W 1.681.701.711.701.681.691.701.701.671.691.701.70

T.C. 34.1 31.1 28.6 25.6 34.7 31.7 29.3 26.2 35.0 32.0 29.6 26.6

S.C. 20.6 20.6 19.7 20.8 22.2 22.2 21.4 22.4 23.3 23.3 22.4 23.6

K.W 1.891.891.891.861.891.891.891.871.891.891.891.87

T.C. 32.3 29.5 27.1 24.2 32.8 30.0 27.7 24.8 33.1 30.4 28.0 25.2

S.C. 20.0 20.0 19.2 20.1 21.6 21.6 20.8 21.7 22.7 22.7 21.7 22.8

K.W 2.072.052.031.992.072.062.042.002.072.062.052.01

T.C. 30.5 27.8 25.6 22.7 30.9 28.3 26.1 23.4 31.1 28.6 26.3 23.9

S.C. 19.4 19.4 18.6 19.4 21.0 21.0 20.1 21.1 22.1 22.1 21.1 22.0

K.W 2.232.192.162.102.232.202.172.122.242.212.182.13

T.C. 28.6 26.0 24.0 21.2 29.0 26.5 24.4 22.1 29.3 26.8 24.7 22.5

S.C. 18.8 18.7 17.9 18.7 20.4 20.4 19.4 20.3 21.5 21.4 20.5 20.8

K.W 2.372.322.272.202.382.332.282.232.382.342.292.24

T.C. 26.7 24.2 22.3 19.7 27.1 24.7 22.6 20.8 27.5 25.0 23.0 21.1

S.C. 18.2 18.0 17.2 18.0 19.8 19.8 18.8 19.5 20.9 20.7 19.9 19.6

K.W 2.512.452.382.302.532.462.392.342.522.472.402.35

036-21315-001 Rev. A (0502)

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHB1206 G2FD036S17 0.96 0.95 1.01

N1VSB12 G2FD036S17 0.98 0.95 0.94

N1VSB12 G2FD046S17 1.00 0.99 0.91

F2FP045 1.02 0.99 1.00

F2RP/F2FP036 0.99 0.99 0.99

G1UA036S14 0.95 0.92 1.00

G1UA048S21,24 1.00 1.00 1.00

GUA036S17,21 0.95 0.92 1.01

GFA036S17,21 0.95 0.92 1.01

GFD030S17 0.95 0.94 1.01

G1UA048S21,24 1.00 1.00 1.00

G2FD036S17 0.96 0.95 1.01

G2FD036S21 0.96 0.96 0.98

GFD048S21,24 1.01 1.01 1.00

G1HD048S 1.00 0.99 1.00

G1NA036S17L 0.97 0.92 1.00

G1NA042S24W 0.97 0.95 1.00

G1NA048S21D 0.97 0.92 1.00

G1UA036S14 0.95 0.92 1.00

T.C. S.C. KW

Variable Speed
Furnace

P1DUA12V G1FA036S14 0.96 0.92 0.95

P1DUA12V G1UA036S14 0.96 0.92 0.95

P1DUB16V G2FD036S17 1.00 0.95 0.93

P1XDB12V G2FD036S17 1.01 0.95 1.00

P1XUB12V G2FD036S17 0.97 0.95 0.95

Coil

T.C. S.C. KW

Unitary Products Group 9

036-21315-001 Rev. A (0502)

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. H1RE036S06

INDOOR COIL MODEL NO. G1UA048S21, 24

CONDENSER

ENTERING AIR

TEMPERATURE

75

85

95

105

115

125

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

ID CFM 1000 1200 1400

ID DB 85 80 70 85 80 70 85 80 70

ID WB 72 67 57 72 67 57 72 67 57

T.C. 40.0 36.9 34.3 41.3 38.1 35.7 42.0 38.9 36.7

S.C. 25.4 24.4 23.4 27.6 26.3 25.5 29.6 27.9 27.2

K.W 1.98 1.96 1.94 1.99 1.97 1.95 2.00 1.98 1.96

T.C. 38.6 35.6 32.7 39.6 36.6 34.0 40.2 37.3 34.9

S.C. 24.8 23.8 22.8 27.0 25.8 24.9 29.1 27.6 26.6

K.W 2.21 2.18 2.17 2.22 2.19 2.18 2.23 2.20 2.19

T.C. 37.2 34.2 31.0 37.8 35.2 32.4 38.4 35.8 33.0

S.C. 24.2 23.3 22.3 26.4 25.3 24.2 28.5 27.2 25.9

K.W 2.44 2.41 2.40 2.45 2.42 2.41 2.46 2.42 2.42

T.C. 35.5 32.3 29.6 36.1 33.1 30.6 36.7 33.7 31.2

S.C. 23.5 22.6 21.7 25.6 24.6 23.5 27.6 26.5 25.3

K.W 2.75 2.72 2.72 2.75 2.73 2.72 2.76 2.73 2.73

T.C. 33.7 30.4 28.1 34.4 31.1 28.7 35.0 31.7 29.4

S.C. 22.8 21.8 21.1 24.7 23.9 22.8 26.8 25.8 24.6

K.W 3.06 3.04 3.03 3.06 3.04 3.02 3.07 3.04 3.03

T.C. 31.9 28.5 26.7 32.7 29.1 26.9 33.3 29.7 27.6

S.C. 22.2 21.1 20.5 23.9 23.1 22.1 25.9 25.1 24.0

K.W 3.37 3.36 3.34 3.37 3.35 3.32 3.38 3.35 3.33

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHB1206 G2FD036S17 0.97 0.97 1.01

N1AHB1206 G2FD046S17 0.99 1.01 1.00

N1VSB12 G2FD046S17 1.00 1.01 0.99

N1VSC16 G2FD048S21 1.02 1.02 0.92

N1AHD14 G2FD048S24 1.01 1.02 0.99

N1AHD14 G2FD060S24 1.02 1.03 0.98

F2FP045 1.02 1.01 0.99

F2RP/F2FP042 0.98 0.98 1.01

F2RP/F2FP036 0.98 0.98 0.99

G1FA048S21,24 1.00 1.00 1.00

GFD042S21 0.99 1.00 1.00

G2FD036S17 0.97 0.97 1.01

G2FD036S21 0.97 0.98 0.99

G2FD046S17 0.99 1.01 1.00

G2FD048S21,24 1.00 1.02 0.99

G1HD048S 0.99 0.99 0.99

G1NA036S17L 0.94 0.92 1.02

G1NA042S24W 0.98 0.99 1.01

GNA048S21D 0.94 0.92 1.02

G1UA048S21,24 1.00 1.00 1.00

T.C. S.C. KW

Variable Speed
Furnace

P1DUB16V G2FD036S17 0.98 0.97 0.95

P1DUC20V G1FA048S21 1.03 1.00 0.89

P1DUC20V G1UA048S21 1.03 1.00 0.89

P1DUC20V G2FD036S21 0.98 0.98 0.93

P1DUC20V G2FD048S21 1.02 1.02 0.90

P1XDB12V G2FD036S17 0.99 0.97 0.97

P1XDD20V G2FD048S24 1.03 1.02 0.97

P1XUB12V G2FD036S17 0.98 0.97 0.95

Coil

T.C. S.C. KW

10 Unitary Products Group

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. H2RE042S06

INDOOR COIL MODEL NO. G1UA060S21,24

CONDENSER

ENTERING AIR

TEMPERATURE

75

85

95

105

115

125

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

ID CFM 1300 1450 1550

ID DB 85 80 75 70 85 80 75 70 85 80 75 70

ID WB 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 47.3 43.8 40.3 37.2 47.7 44.3 40.9 37.7 48.0 44.5 41.2 38.0

S.C. 28.3 28.5 28.9 29.2 29.8 30.0 30.6 30.7 30.8 31.0 31.6 31.7

K.W 2.882.842.802.772.952.902.872.843.002.952.912.88

T.C. 44.6 41.3 38.1 35.1 45.0 41.8 38.6 35.5 45.2 42.1 38.8 35.9

S.C. 27.4 27.6 28.1 28.2 29.0 29.2 29.6 29.8 30.0 30.2 30.6 30.8

K.W 3.14 3.10 3.06 3.04 3.20 3.16 3.13 3.11 3.25 3.21 3.17 3.15

T.C. 42.2 39.0 36.0 33.1 42.5 39.5 36.4 33.7 42.8 39.7 36.6 33.9

S.C. 26.6 26.8 27.2 27.4 28.2 28.4 28.7 28.9 29.3 29.4 29.7 29.8

K.W 3.453.413.393.373.523.483.453.433.563.523.493.47

T.C. 39.7 36.8 33.9 31.2 40.1 37.2 34.2 31.8 40.3 37.3 34.4 32.2

S.C. 25.9 26.1 26.4 26.6 27.5 27.6 27.9 28.2 28.5 28.5 28.9 28.6

K.W 3.823.793.773.753.893.863.833.813.933.903.873.85

T.C. 37.2 34.5 31.7 29.3 37.6 34.8 32.1 30.0 37.8 35.0 32.3 30.3

S.C. 25.1 25.2 25.5 25.6 26.7 26.7 27.1 26.6 27.7 27.7 27.9 26.9

K.W 4.264.234.214.194.324.294.274.264.364.344.314.30

T.C. 34.7 32.2 29.5 27.4 35.1 32.4 30.0 28.2 35.3 32.7 30.2 28.4

S.C. 24.3 24.3 24.6 24.6 25.9 25.8 26.3 25.0 26.9 26.9 26.9 25.2

K.W 4.704.674.654.634.754.724.714.714.794.784.754.75

036-21315-001 Rev. A (0502)

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHC1606 G2FD042S21 0.96 0.95 1.00

N1AHC1606 G2FD048S21 0.98 0.98 0.99

N1AHD1406 G2FD060S24 1.00 1.00 0.98

N1VSC16 G2FD048S21 1.00 0.98 0.94

N1VSD20 G2FD060S24 1.02 1.00 0.92

F2FP045 1.00 1.01 0.98

F2FP048 0.98 0.98 1.02

G1NA042S24W 1.00 1.00 1.00

GNA048S21D 0.96 0.92 0.99

G1FA048S21,24 0.96 0.96 0.99

G1FA060S21,24 1.00 1.00 1.00

G1UA048S21,24 0.96 0.96 0.99

G1UA060S21,24 1.00 1.00 1.00

G2FD042S21 0.96 0.95 0.99

G2FD046S17 0.96 0.97 0.99

G2FD048S21,24 0.98 0.98 0.98

G2FD060S24 1.00 1.00 1.00

GHD048S 0.96 0.96 0.99

T.C. S.C. KW

Variable Speed
Furnace

P1DUC20V G1FA048S21 0.98 0.96 0.92

P1DUC20V G1FA060S21 1.01 1.00 0.93

P1DUC20V G1UA048S21 0.98 0.96 0.92

P1DUC20V G1UA060S21 1.01 1.00 0.93

P1DUC20V G2FD042S21 0.98 0.95 0.94

P1DUC20V G2FD048S21 0.99 0.98 0.92

P1DUC20V G2FD048S21 0.99 0.98 0.93

P1XDD20V G2FD048S24 1.01 0.98 0.96

P1XDD20V G2FD060S24 1.16 1.00 1.12

Coil

T.C. S.C. KW

Unitary Products Group 11

036-21315-001 Rev. A (0502)

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. H2RE048S06

INDOOR COIL MODEL NO. G2FD060S24, G1UA060S21,24

CONDENSER

ENTERING AIR

TEMPERATURE

75

85

95

105

115

125

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

ID CFM 1400 1600 1800

ID DB 85 80 70 85 80 70 85 80 70

ID WB 72 67 57 72 67 57 72 67 57

T.C. 53.3 49.5 45.5 54.3 50.2 46.4 55.2 51.0 47.3

S.C. 33.4 32.6 31.1 35.9 35.0 33.0 38.3 37.4 34.9

K.W 2.76 2.72 2.69 2.77 2.74 2.70 2.77 2.76 2.70

T.C. 51.2 47.7 43.9 52.0 48.4 44.8 52.8 49.1 45.7

S.C. 33.1 32.1 30.6 35.4 34.5 32.6 37.7 36.8 34.6

K.W 3.07 3.04 3.01 3.07 3.05 3.02 3.08 3.06 3.03

T.C. 49.0 45.9 42.4 49.7 46.5 43.2 50.3 47.2 44.1

S.C. 32.7 31.6 30.0 34.9 33.9 32.2 37.1 36.2 34.4

K.W 3.37 3.35 3.33 3.38 3.36 3.34 3.38 3.37 3.35

T.C. 46.6 43.5 40.1 47.3 44.1 40.8 48.0 44.7 41.6

S.C. 31.7 30.7 29.0 34.0 32.9 31.2 36.3 35.1 33.3

K.W 3.78 3.75 3.74 3.79 3.76 3.75 3.79 3.77 3.75

T.C. 44.1 41.1 37.8 44.9 41.6 38.4 45.6 42.2 39.1

S.C. 30.8 29.8 28.1 33.1 31.9 30.2 35.4 34.1 32.3

K.W 4.18 4.16 4.15 4.19 4.16 4.15 4.21 4.16 4.15

T.C. 41.7 38.7 35.5 42.5 39.2 36.0 43.3 39.7 36.6

S.C. 29.8 28.8 27.1 32.2 31.0 29.2 34.6 33.1 31.3

K.W 4.59 4.56 4.56 4.60 4.56 4.55 4.62 4.56 4.55

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHD2006 G2FD060S24 0.99 0.99 1.00

N1AHD2006 G2FD061H24 1.00 1.00 1.00

N1VSC16 G2FD048S21 0.98 0.97 0.95

N1VSD20 G2FD060S24 1.00 0.99 0.96

F2FP060 0.98 0.97 1.04

F2FV060 1.01 1.02 0.91

G1NF060SOF 0.99 0.96 0.99

G1UA048S21,24 0.96 0.95 0.99

G1UA060S21,24 0.99 0.99 1.00

G2FD048S21,24 0.97 0.97 0.99

G2FD060S24 0.99 0.99 1.00

G2FD061H24 1.00 1.00 1.00

G1FA048S21,24 0.96 0.95 0.99

G1FA060S21,24 0.99 0.99 1.00

G1HD048S 0.96 0.94 1.00

G1NA042S24W 0.99 0.96 0.99

GNA048S21D 0.94 0.85 0.97

T.C. S.C. KW

Variable Speed
Furnace

P1DUC20V G1FA060S21 0.99 0.99 0.97

P1DUC20V G1UA060S21 0.99 0.99 0.97

P1DUC20V G2FD048S21 0.97 0.97 0.96

P1XDD20V G2FD060S24 1.00 0.99 0.98

Coil

T.C. S.C. KW

12 Unitary Products Group

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. H2RE060S06

INDOOR COIL MODEL NO. G2FD060S24; G1UA060S21, 24

CONDENSER

ENTERING AIR

TEMPERATURE

75

85

95

105

115

125

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

ID CFM 1600 1800 2000

ID DB 85 80 70 85 80 70 85 80 70

ID WB 72 67 57 72 67 57 72 67 57

T.C. 63.5 59.2 54.7 63.6 59.9 55.5 63.7 60.6 56.2

S.C. 42.2 40.8 39.1 43.5 42.1 40.3 44.7 43.4 41.5

K.W 3.18 3.16 3.12 3.19 3.17 3.13 3.20 3.17 3.14

T.C. 61.3 57.2 52.3 61.5 57.7 53.1 61.8 58.2 53.9

S.C. 41.7 40.2 37.9 42.9 41.4 39.1 44.2 42.7 40.3

K.W 3.59 3.56 3.51 3.60 3.57 3.53 3.61 3.57 3.54

T.C. 59.1 55.2 49.8 59.5 55.5 50.7 59.8 55.8 51.6

S.C. 41.1 39.6 36.8 42.4 40.8 37.9 43.8 42.0 39.1

K.W 4.00 3.97 3.91 4.00 3.97 3.92 4.01 3.97 3.93

T.C. 55.9 52.1 47.6 56.5 52.5 48.0 57.1 52.9 48.4

S.C. 40.0 38.3 35.7 41.4 39.6 37.1 42.8 40.8 38.4

K.W 4.51 4.47 4.43 4.52 4.48 4.44 4.53 4.48 4.45

T.C. 52.8 49.0 45.3 53.5 49.5 45.2 54.3 50.0 45.2

S.C. 38.9 37.0 34.6 40.4 38.3 36.2 41.8 39.7 37.7

K.W 5.01 4.98 4.95 5.03 4.99 4.96 5.05 5.00 4.96

T.C. 49.6 45.9 43.0 50.6 46.5 42.5 51.5 47.0 42.0

S.C. 37.8 35.7 33.5 39.3 37.1 35.3 40.9 38.5 37.1

K.W 5.52 5.48 5.46 5.54 5.50 5.47 5.56 5.51 5.48

036-21315-001 Rev. A (0502)

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

N1AHD2006 G2FD060S24 1.00 1.00 1.00

N1AHD2006 G2FD061H24 1.02 1.05 1.01

N1VSD20 G2FD060S24 1.01 1.00 0.98

N1VSD20 G2FD061H24 1.02 1.05 0.96

F2FP060 0.99 1.01 1.03

F2FV060 1.07 1.05 1.05

G1FA060S21,24 1.00 1.00 1.00

G1HD060 0.98 0.98 0.99

G1NA060S24T 0.99 0.97 0.99

G1UA060S21,24 1.00 1.00 1.00

G2FD060S24 1.00 1.00 1.00

G2FD061H24 1.02 1.05 1.01

T.C. S.C. KW

Variable Speed
Furnace

P1DUC20V G1FA060S21 1.00 1.00 0.99

P1DUC20V G1UA060S21 1.00 1.00 0.99

P1XDD20V G2FD060S24 0.98 1.05 0.97

Coil

T.C. S.C. KW

Unitary Products Group 13

036-21315-001 Rev. A (0502)

MATCHING INDOOR COMPONENTS

ADD-ON COILS - FOR FURNACE APPLICATIONS

G1UA
1/2 CASED
UPFLOW

G1FA
FULL CASED
UPFLOW

* Available with factory installed horizontal drain pan.

G1HD
HORIZONTAL DUCT

AIR HANDLERS - FOR NON-FURNACE APPLICATIONS

G1NA
UNCASED
UPFLOW

G2FD*
MULTI-POSITION
(UPFLOW, HORIZONTAL
AND DOWNFLOW)

N1AH OR N1VS
MODULAR BLOWER
(UPFLOW, HORIZONTAL
AND DOWNFLOW)

G2FD
COIL

F2RC / F2FC OR
F2RC / F2FP / F2FV
FAN COIL UNITS
(UPFLOW, HORIZONTAL)

14 Unitary Products Group

NOTES

036-21315-001 Rev. A (0502)

Unitary Products Group 15

Subject to change without notice. Printed in U.S.A. 036-21315-001 Rev. A (0502)
Copyright © by York International Corp. 2002. All rights reserved. Supersedes: 550.50-TG1Y (600)

Unitary 5005 Norman
Product York OK
Group Drive 73069