Page 1
OWNER’S MANUAL
OUTDOOR SPLIT-SYSTEM
HEAT PUMP
15 SEER 2.5 TO 5 TONS
TABLE OF CONTENTS
HOW YOUR HEAT PUMP WORKS .2
SYSTEM OPERATION . . . . . . . . . . .2
THERMOSTATS . . . . . . . . . . . . . . . . . . . . 2
FAN OPERATION SELECTION . . . . . . . .2
HEATING CYCLE . . . . . . . . . . . . . . . . . . .2
COOLING CYCLE . . . . . . . . . . . . . . . . . . . 3
TO MAXIMIZE OPERATING
EFFICIENCY . . . . . . . . . . . . . . . . . . . 3
HEATING CONSERVATION . . . . . . . . . .3
COOLING CONSERVATION . . . . . . . . . .3
CARE OF SYSTEM . . . . . . . . . . . . . .3
COIL CARE . . . . . . . . . . . . . . . . . . . . . . . .3
FILTER CARE . . . . . . . . . . . . . . . . . . . . . .3
SERVICE CALLS . . . . . . . . . . . . . . .4
PARTS INFORMATION . . . . . . . . . . . . . . 4
CHARACTERISTICS OF HEAT
PUMPS . . . . . . . . . . . . . . . . . . . . . . .4
A CONSTANT HEAT . . . . . . . . . . . . . . . .4
WATER RUN-OFF . . . . . . . . . . . . . . . . . . 4
OUTDOOR COIL DEFROSTING . . . . . . .4
MODELS: E4TS030
E4TS036
E4TS048
E4TS060
035-16473-001 Rev. A (202)
Page 2
035-16473-001 Rev. A (202)
Congratulations . . .
On your purchase of one of the most versatile heat pump systems available in the industry today. This Stealth series high efficiency system has been precision designed, manufactured of high quality materials and has passed many vigorous inspections
and tests to ensure years of satisfactory service.
This booklet is meant to increase your understanding of your system, tell you how to operate it efficiently and how to obtain
the greatest measure of comfort at the lowest operating expense. Please read this booklet thoroughly.
We appreciate your interest in our product and your decision to purchase our system. Enjoy your comfort.
This Heat Pump has been specially
developed and built as a heat pump to meet the dual needs of heating and
cooling. It's not just an air conditioner
with extra parts. That's why you can
rely on efficient, trouble-free operation.
Your system is fully automatic. Set the
thermostat and forget it. And it's automatically protected from damage by
voltage fluctuations or excessive heating or cooling demands.
Your split system heat pump consists
of two units - one installed outdoors
and one installed indoors. The indoor
unit may be installed in a basement,
attic, or crawl space.
HOW YOUR HEAT PUMP
WORKS
If your hand is wet and you blow on it,
it feels cool because some of the moisture is evaporating and becoming a
vapor. This process requires heat. The
heat is being taken from your hand, so
your hand feels cool.
That's what happens with a heat
pump. During the cooling cycle, your
system will remove heat and humidity
from your home and will transfer this
heat to the outdoor air.
During the heating cycle, your system
will remove heat and humidity from the
outdoor air and will transfer this heat to
your home. This is possible because
even 0°F outdoor air contains a great
deal of heat. Remember that your heat
pump doesn't generate much heat, it
merely transfers it from one place to
another
SYSTEM OPERATION
THERMOSTATS
Though thermostats may vary widely in
appearance they are all designed to
perform the same basic function, to
control the operation of your air conditioning system. Regardless of size or
shape, each thermostat will feature a
temperature indicator; a dial, arm or
push button for selection of the desired
temperature; a fan switch to choose
the indoor fan operation; and a comfort
switch for you to select the system
mode of operation.
Your new unit will require a three stage
heating / two stage cooling thermostat
for optimum efficiency and energy savings. Please be aware that many dif-
ferent thermostats operate on
batteries or “power stealing” principals. UPG can not support such
models to be trouble free when
used with this unit.
The following illustrations and discussion will aid you to determine which
type of thermostat you have for your
system.
A complete operating instruction is provided by the manufacturer for each
thermostat. Familiarize yourself with its
proper operation to obtain the maximum comfort with a minimum of
energy consumption.
FIGURE 1:PROGRAMMABLE
ELECTRONIC THERMOSTAT
FAN OPERATION SELECTION
A multi-position fan switch allows you
to choose the type of fan operation of
the indoor fan.
AUTO
With the thermostat fan switch set to
“AUTO”, the fan will run intermittently
as required for either heating or cooling. This position will provide the lowest operating cost. If you purchased
one of the recommended thermostats,
they have an Intelligent fan mode
which continually circulates the air during occupied modes or when you are
at home, and can cycle the fan during
unoccupied mode or during the night
while you sleep to further conserve
energy.
ON
CONTINUOUS FAN OPERATION:
With the thermostat fan switch set to
“ON”, the indoor fan will not shut off.
However, the cooling and heating systems will still operate as required by
room temperatures. This provides continuous air filtering and more even temperature distribution to all conditioned
spaces.
FAN ONLY OPERATION: On moderate days, usually during spring and fall,
when neither heating nor cooling is
required, you may want to run only the
fan to ventilate, circulate and filter the
air in your home or building. Set the
comfort control switch to “OFF” and the
fan switch to “ON”. Be sure to return
the switches to their original positions
for normal operation.
The Main power to the system must be kept “ON” at all
times to prevent damage to
the outdoor unit compressor.
If necessary, the thermostat
control switch should be used
to turn the system “OFF”.
Should the main power be
disconnected or interrupted
for 8 hours or longer, DO
NOT attempt to start the system for 8 hours after the
power has been restored to
the outdoor unit. If heat is
needed during this 8 hour
period, use emergency heat.
HEATING CYCLE
With the thermostat in the heating
position, and the outdoor temperature
in the range of 20 to 30° or below, the
outdoor unit will generally run 100% of
the time.
2 Unitary Products Group
Page 3
035-16473-001 Rev. A (202)
All E*TS systems are equipped with
balance point control to provide even
more efficient operation. This control
will prevent the electric heater from
being energized when the outdoor air
is above some predetermined temperature setting (0 to 45° F). At higher
temperatures, your system will provide
all the heat your home will ever need.
At lower temperatures, the supplemental electric heat will be energized to
keep your home comfortable.
When the outdoor air is cool and moist,
frost may form on the surface of your
outdoor coil. When this frost builds to a
certain point, your system will switch to
a defrost cycle. Although you may feel
cooler air coming from your registers,
DO NOT adjust your thermostat. The
frost will melt quickly, and your system
will return to normal operation automatically.
FIGURE 2:
COOLING CYCLE
Switch your thermostat to cool. Select
a comfortable thermostat temperature
setting, typically between 75 and 80°.
Comfort sensations vary with individuals. The lower the indoor temperature
desired, the greater will be the number
of hours your unit must operate.
Set your thermostat 2 or 3° F below
normal several hours before entertaining large groups during hot weather.
People give off considerable heat and
moisture.
On an extremely hot day, the indoor
temperature may rise 3 to 6° F above
the thermostat setting. Properly
selected equipment does not have the
capacity to maintain a constant indoor
temperature during this peak load.
Over-sizing your system to handle this
peak load isn't practical because the
oversized system would operate much
less efficiently at all other conditions.
FIGURE 3:
TO MAXIMIZE OPERATING
EFFICIENCY
HEATING CONSERVATION
For the most sufficient operation, keep
storm windows and doors on all year
long. They not only help to insulate
against heat and cold, but keep out
dirt, pollen and noise, too.
Closing the drapes at night, keeping
fireplace dampers closed when not in
use, and running exhaust fans only
when necessary, will help you to retain
the air you have already paid to heat.
COOLING CONSERVATION
To comfortably cool your home, your
heat pump must remove both heat and
humidity. Don't turn your system off
even though you will be away all day.
On a hot day, your system may have to
operate between 8 and 12 hours to
reduce the temperature in your home
to a normal comfort level.
Keep windows closed after sundown.
While the outdoor temperature at night
may be lower than indoors, the air is
generally loaded with moisture which is
soaked up by furniture, carpets, and
fabrics. This moisture must be
removed when you restart your system.
The hotter the outside temperature, the
greater the load on your system.
Therefore do not be alarmed when
your system continues to run after the
sun has set on a hot day. Heat is
stored in your outside walls during the
day and will continue to flow into your
home for several hours after sunset.
Use your kitchen exhaust fan when
cooking. One surface burner on "High"
requires one ton of cooling. Turn on
your bathroom exhaust fan while
showering to remove humidity.
You can also help your system in the
summer by closing drapes or blinds
and by lowering awnings on windows
that get direct sunlight.
CARE OF SYSTEM
A periodic inspection, cleaning, lubrication and adjustment of your heat pump
is available from your dealer. Be sure
to ask him about this service. For
those who prefer to do-it-yourself, follow the instructions below to care for
your system.
COIL CARE
Keep outdoor unit free of snow, foliage
and grass, grass clippings, leaves,
paper, and any other material which
could restrict proper air flow in and out
of the unit. The coil may be vacuumed
to remove any debris from between the
fins.
If the coil becomes excessively dirty,
turn the Main Disconnect Switch to
“OFF” and wash the coil with your garden hose. Avoid getting water into the
fan motor and control box. Flush dirt
from base pan after cleaning the coil.
FILTER CARE
Inspect the air filter(s) at least once a
month. If they are dirty, wash reusable
filters with a mild detergent per manufacturer's recommendations. Replace
disposable filters with new filters.
Install the clean filters with “air flow”
arrow in the same direction as the air
flow in your duct. Filters should be
clean to assure maximum efficiency
and adequate air circulation. Drapes,
furniture or other obstructions blocking
your supply and return air grilles will
decrease efficiency.
NOTE: There will be no heat available
until power is reestablished.
HEATING SEASON
1. Leave on Emergency Heat for at
least 8 hours after electrical power
is reestablished if the power was
off more than 8 hours.
2. Switch thermostat back to Heating
or Auto.
COOLING SEASON
1. Switch thermostat to Off position.
Unitary Products Group 3
Page 4
2. Do not switch to Cooling or Auto
until electrical power has been
reestablished for 8 hours if the
power was off more than 8 hours.
SERVICE CALLS
There are a few instances where you
can avoid unnecessary service calls.
(See Troubleshooting Guide above).
The flashing light on the system thermostat of E*TS units is capable of providing you with time and money saving
information. The fault code numbers
listed can be handled by taking the
corrective action indicated. Call qualified serviceman if displaying fault code
numbers not listed.
PARTS INFORMATION
Replacement parts are available from
local YORK contractor/dealers or the
nearest YORK distribution center.
CHARACTERISTICS OF
HEAT PUMPS
A CONSTANT HEAT
Heat pumps have a noticeably cooler
supply air temperature than furnaces.
The common practice of over-sizing
furnaces contributes to an “off-and-onagain” operation with short blasts of
hot supply air. The heat pump system
is sized more closely to the heating
needs of your home. Heat is supplied
at a lower temperature over a longer
period of time to provide a more constant heat, and it may give you the
impression that your system “never
stops running".
WATER RUN-OFF
During the heating cycle, in mild
weather you may notice water running
off the outdoor coil. Moisture from the
air is condensed on the outside sur-
face of the coil where it gathers and
runs off.
No need for alarm, your unit has not
sprung a leak!
OUTDOOR COIL DEFROSTING
At certain outdoor conditions (low temperature, high humidity), frost may
build up on the coil of the outdoor unit.
In order to maintain heating efficiency,
the system will automatically defrost
itself. Steam rising from the outdoor
unit is normal and is an indication of
proper operation. The vapor cloud will
only last for a few minutes. When the
defrost cycle is completed, the system
will automatically switch back to heating. Electric heat is automatically energized to maintain comfort during
defrost.
TROUBLESHOOTING GUIDE
PROBLEM CHECK: ACTION TO TAKE FAULT CODE
1. Thermostat for proper setting. Set thermostat to proper setting. -
2. Circuit breakers and fuses. Reset circuit breakers - Replace blown fuses. -
NO HEAT OR
COOLING
3. Check Outdoor unit for dirty coil. (Cooling) Clean coil, see “Coil Care” section. 2
4. Outdoor unit for snow accumulation. (Heating) Remove snow. 5
5. Indoor unit for dirty filter. (Heating) Clean or Replace, see “Filter Care” section. 2
6. Emergency Heat Light Status on thermostat.
After completing the checks and actions above, turn thermostat to “OFF” for 10 seconds and attempt
restart. Wait 5 minutes. If system does not start, call qualified serviceman.
Obtain the fault code number of times the Emergency Heat light on the thermostat flashes between
pauses.
Subject to change without notice. Printed in U.S.A. 035-16473-001 Rev. A (202)
Copyright © by York International Corp. 2002. All rights reserved. Supersedes: Nothing
Unitary 5005 Norman
Products York OK
Group Drive 73069
Loading...