York 036-048, 90, 60 User Manual

TECHNICAL GUIDE
SPLIT -SYSTEM HEAT PUMPS
10 SEER – R-22
MODELS:
E*RA036 THRU 060

(3 THRU 5 NOMINAL TONS, 3 PH)

MODELS: 036-048 (3 PH)

MODELS: 060, 090 (3 PH)

ISO 9001

Certified Quality

LISTED

Due to continuous product improve m ent, specifications
are subject to change without notice.

Visit us on the web at www.york.com
Additional rating information can be found at

www.ari.org/aridirectory.

Management System

279104-YTG-B-0307

DESCRIPTION

The 10 SEER Series heat pumps is the outdoor part of a ver­satile system of heat pumps. It is designed to be custom­matched with one of UPG’s complete line of evaporator sec­tions, with each serving a specific function. Matching Air Han­dlers are available for upflow, downflow, or horizontal
applications to provide a complete system. Electric Heaters
are available, if required. Add-On coils are availa ble for use
with upflow, downflow, or horizontal furnaces and air han­dlers.

WARRANTY

1-year limited parts warranty.

5-year limited compressor warranty.

FEATURES

• QUALITY COILS - The coil is constructed of copper tube
and aluminum fins.

• COIL PROTECTION - Coils are protected from damage by
a polymer mesh applied between the coil face, and a PVC
coated steel coil guard.

• PROTECTED COMPRESSOR - The compressor is inter­nally protected against high pressure and temperature.
This is accomplished by the simultaneous operation of
high pressure relief valve and a temperature sensor which
protects the compressor if undesirable operating condi­tions occur. A liquid line filter-drier further protects the
compressor.

• DURABLE FINISH - Cabinet is made of pre-painted steel.
The pre-treated flat galvanized steel provides a better
paint to steel bond, which resists corrosion and rust creep.
Special primer formulas and matted-textured finish insure
less fading when exposed to sunlight.

• LOWER INSTALLED COST - Installation time and costs
are reduced by easy power and control wiring connections.
Discharge line heat exchanger knockouts are provided, if
required. Available in sweat connect models only. The unit
contains enough refrigerant for matching indoor coils and
15 feet of interconnecting piping. The small base dimen­sion means less space is required on the ground or roof.

• TOP DISCHARGE - The warm air from the top mounted
fan is blown up away from the structure and any landscap­ing. This allows compact location on multi-unit applica­tions.

• LOW OPERATING SOUND LEVEL - The upward air flow
carries the normal operating noise away from the living
area. The rigid top panel effectively isolates any motor
sound. Isolator mounted compressor and the rippled fins of
the condenser coil muffle the normal fan motor and com­pressor operating sounds.

• LOW MAINTENANCE - Long life permanently lubricated
motor-bearings need no annual servicing.

• EASY SERVICE ACCESS - Fully exposed refrigerant con­nections, a single panel covering the electrical controls,
and the molex plug in the control box connecting the con­denser fan make for easy servicing of the unit.

• SECURED SERVICE VALVES - Secured re-usable ser-
vice valves are provided on both the liquid and vapor
sweat connections for ease of evacuating and charging.

• U.L. and C.U.L. listed - approved for outdoor application.

Certified in accordance with the Unitary Small Equipment cer­tification program, which is based on ARI Standard 210/240.

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

279104-YTG-B-0307

Physical and Electrical Data

MODEL E1RA036S25 E2RA048S25 E1RA060S25 E1RA036S46 E2RA048S46 E1RA060S46

Unit Supply Voltage

Normal Voltage Range
Minimum Circuit Ampacity 15.0 18.9 24.5 8.0 10.1 12.0

Max. Qvercurrent Device Amps
Compressor Type

Compressor Amps Rated Load 10.9 14.1 18.6 5.8 7.0 9.0

Crankcase Heater Yes No No Yes No No
Fan Motor Amps Rated Load 1.4 1.3 1.3 .8 .7 .8
Fan Diameter Inches 18 22 24 18 22 24
Fan Motor Rated HP 1/4 1/4 1/4 1/4 1/5 1/4

Coil Face Area Sq. Ft. 12.58 19.65 18.00 12.58 19.65 18.00

Rows Deep 112112

Fin / Inches 14 13 14 14 13 14
Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8
Vapor Line Set OD (Field Installed) 3/4 7/8 7/8 3/4 7/8 7/8

Unit Charge (Lbs. - Oz.)
Charge Per Foot, Oz. .68 .70 .70 .68 .70 .70
Operating Weight Lbs. 178 232 243 178 232 243

1. Rated in accordance with ARI Standard 110, utilization range “A”.

2. Dual element fuses or HACR circuit breaker.

3. All scrolls listed with a superscript “D” are Danfoss scrolls. All scrolls listed with a superscript “C” are Copeland scrolls.

4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than
15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.

1

2

3

25 30 40 15 15 20

Inertia

Locked Rotor 78 125 128 40 55 63

Nominal RPM 1,100 850 850 1,100 825 850
Nominal CFM 2,750 3,500 3,100 2,750 3,500 3,100

4

5 - 12 8 - 3 11 - 3 5 - 12 8 - 3 11 - 3

208/230-3-60 460 - 3 - 60

187 to 252 432 to 504

Scroll

D

Scroll

C

Inertia

Scroll

D

Scroll

C

All dimensions are in inches. They are subject to change
without notice. Certified dimensions will be provided upon

C

request.

DIMENSIONS

A

Unit

Model

Dimensions

(Inches)

1

A

B C Liquid Vapor

036 25 35 23
048 33 37 27 7/8”

B

060 26 43 32 7/8”

1. Including fan guard.

Refrigerant
Connection

Service Valve Size

3/4”

3/8”

2 Unitary Products Group

279104-YTG-B-0307

Additional R-22 Charge / Orifice Size for Various Matched Systems

Outdoor Unit E1RA036S(25,46) E1RA048S(25,46) E1RA060S(25,46)

Unit Orifice (s)
Factory R-22 Charge, lbs-oz 5 - 12 8 - 3 11 - 3

Indoor Coil System Orifice = Additional Charge, Oz
FC/MC/PC35(B,C)3X 81 + 8 – –
FC/MC/PC/UC36(A,B,C)3X 71 + 7 – –
FC/MC/PC/UC42(B,C)3X 81 + 8 – –
FC/MC/PC/UC48C3X – 87 + 6 –
FC/MC/PC/UC48D3X – 87 + 6 –
FC/MC/PC/UC60C3X – 84 + 4 99 + 0
FC/MC/PC/UC60D3X – 84 + 4 99 + 0
AHP36C3X 81 + 13 84 + 3 –
AHP42C3X 81 + 13 84 + 3 –
AHP/SHP48D3X – 84 + 4 99 + 0
AHP60D3X – 84 + 4 99 + 0
G1NA036S17L 71 + 7 – –
G1NA048S21D 71 + 7 81 + 8 –
G1NA048S24P – 81 + 8 –
G1UA048S21/24 81 + 13 84 + 3 –
G1UA060S24 – 84 + 4 99 + 0
G1FA048S21/24 81 + 13 84 + 3 –
G1FA060S24 – 84 + 4 99 + 0
G2FD042S21 81 + 8 – –
G2FD048S21/24 – 87 + 6 –
G2FD060S24 – 84 + 4 99 + 0

FOOTNOTES:

1. These orifices are packed in the instruction/warranty packet of each outdoor unit.

PROCEDURES:

1. Unit factory charge listed on the unit nameplate includes refri gerant for the condenser, the smallest evaporator and 15 feet of intercon­necting line tubing.

2. Verify the orifice size and additional charge required for specific evaportor coil in the system using the above table.

3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above.

4. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for
evaportor + adder for line set.

5. If the orifice in the evaportor was changed, verify the evaportor nameplate has been marked with the correct orifice size.

1

71, 81 81, 84, 87 99

Unitary Products Group 3

279104-YTG-B-0307

COOLING CAPACITY - With Air Handler Coils

COOLING

SEER

W/O TXV

SEER

WITH TXV

EER

3

UNIT MODEL

MODEL

AIR HANDLER

ELECTRIC

HEAT KW

2

W

COIL

MODEL

1

RATED

CFM

NET MBH

TOTAL SENS.

3 PH 10 SEER HP WITH MA / MC / N-AH / G2FD

MA12BN2,4 10 17 FC/MC35B3X 1250 34.4 25.3 10 – 8.95

E1RA036S(25,46)

MA12BN2,4 10 17 FC/MC36B3X 1250 34.4 25.3 10 – 8.95
MA12BN2,4 10 17 FC/MC42B3X 1250 34.4 25.3 10 – 8.95

N1AHC1646 10, 15 21 G2FD042(S,H)21 1250 34.2 25.3 10 – 8.95

MA16CN4 10, 15 21 FC/MC48C3X 1600 45.5 33.7 10 – 9.45
MA20DN2 10, 15, 25 24 FC/MC48D3X 1725 45.5 33.7 10 – 9.45

E2RA048S(25,46

MA20DN4 10, 15, 29 24 FC/MC48D3X 1725 45.5 33.7 10 – 9.45
N1AHC1646 10, 15 21 G2FD048(S,H)21 1600 45.5 33.7 10 – 9.45
N1AHD2046 10, 15, 29 24 G2FD048(S,H)24 1600 45.5 33.7 10 – 9.45

E1RA060S(25,46)

MA20DN4 10, 15, 29 24 FC/MC60D3X 2000 57.0 41.0 10 – 9.80
N1AHD2046 10, 15, 29 24 G2FD048(S,H)24 1700 57.0 41.0 10 – 9.80

3 PH 10 SEER HP WITH AHP / SHP / F2RP / RC / FP / FC

4,5

F2RP/FP036 5, 8, 10, 15, 19 21 – 1250 34.0 24.9 10 – 9.00

E1RA036S25

F2RD/FP042 5, 8, 10, 15 21 – 1250 34.0 25.6 10 – 9.00

AHP36C3X 10, 15 21 – 1250 34.0 25.6 10 – 9.00
AHP42C3X 10, 15, 18 21 – 1250 34.0 25.6 10 – 9.00

F2FP048 5, 8, 10, 15, 20, 25 24 – 1600 45.0 33.5 10 – 9.40

E2RA048S25

F2FP060 5, 8, 10, 15, 20, 25 24 – 1600 46.5 34.4 10 – 9.60

AHP/SHP48D3X 10, 15, 18 24 – 1600 46.5 34.4 10 – 9.60

E1RA060S25

Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210/240.
Cooling MBH based on 80°F entering air temperature, 50% RH, and rated air flow.
KW includes compressor, out door fan and indoor blower motor watts. Add-on coils include 365 watts/1000 CFM for blower motor.
EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at a 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions.
SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power input
in watt-hours during the same period.

1. G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number.

2. Single phase units require single phase 2HK heaters.

F2FP060 5, 8, 10, 15, 20, 25 24 – 1700 56.0 40.0 10 – 9.40

AHP/SHP60D3X 10, 15 24 – 1700 56.0 40.0 10 – 9.40

3. TXV = Use 1TV700 Series Kit.

4. To meet R=4.2 insulat ion requirements, substitute F2FP for F2RP, and F2FC for F2RC. models. All ratings remain the same.

5. FG8, FG9, and FL8 furnaces and F2RP / F2RC air handlers have B.O.D. standard.

- = Not applicable

4 Unitary Products Group

COOLING CAPACITY - Upflow, Downflow, & Horizontal Furnaces and Coils

FURNACE**

UNIT MODEL

E1RA036S(25,46

E2RA048S(25,46

E1RA060S(25,46)

1. TXV = Use 1TV700 Series Kit.
* Requires a 2FD Blower Time Delay unless a standard furnace is equipped with one.

**

Refer to Quick Selection Chart for specific furnace match-up.

CFM RANGE

(MIN.-MAX.)

1100
1400

1400
1800

1600
2100

W

21,24 G1FA048S21 1250 34.4 24.7 10 – 9.05

17 G1NA036S17L 1250 35.0 26.2 10 – 9.00
21 G1NA048S21D 1250 35.0 26.2 10 – 8.95

21,24 G1UA048S21 1250 34.4 24.7 10 – 9.05

21 G2FD042S21 1250 34.2 25.3 10 – 8.95

17,21 FC/MC/PC35*3X 1250 34.4 24.7 10 – 9.5

14,17,21 FC/MC/PC/UC36*3X 1250 34.4 24.7 10 – 9.5

17,21 FC/MC/PC/UC42*3X 1250 34.4 24.7 10 – 9.5
21,24 G1FA048S21 1600 45.5 32.7 10 – 9.30

21 G1NA048S21D 1600 45.0 31.2 10 – 9.50
21,24 G1UA048S21 1600 45.5 32.7 10 – 9.30
21,24 G2FD048(S,H)21,24 1600 45.5 33.7 10 – 9.40

21 FC/MC/PC/UC48C3X 1600 45.5 32.7 10 – 9.30

24 FC/MC/PC/UC48D3X 1600 45.5 32.7 10 – 9.30
21,24 G1FA060S21,24 1700 57.0 41.0 10 – 9.80
21,24 G1UA060S21,24 1700 57.0 41.0 10 – 9.80

24 G2FD060(S,H)24 1700 57.0 41.0 10 – 9.80

21 FC/MC/PC/UC60C3X 1725 57.0 41.0 10 – 9.80

24 FC/MC/PC/UC60D3X 2000 57.0 41.0 10 – 9.80

COIL

MODEL

RATED

CFM

NET MBH

TOTAL SENS.

COOLING

SEER

W/O TXV

279104-YTG-B-0307

SEER + TXV

+ TDR*

1

EER

Unitary Products Group 5

279104-YTG-B-0307

HEATING PERFORMANCE - With Air Handler

UNIT

MODEL*

COIL

MODEL

1

ARI HEATING

2

47°F17°F HSPF -3°F7°F17°F27°F37°F47°F57°F

OUTDOOR TEMP

MBH COP MBH COP STD MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW

E1RA036S(25,4

E2RA048S(25,46

E1RA060S(25,46)

1. Rated CFM same as for cooling.

2. Heating MBH based on ARI standards of 70° DB entering ind oor a ir, 72% RH outdoor air with 25 feet of interconnecting piping and no supplement al
electric heat operation.

3. Integrated heating capacities include the effect of defrost cycles in the temperature range where they occur.

COP equals MBH output divided by (total KW input x 3.412).
HSPF (Heating Seasonal Performance Factor) is the total heating output during a normal annual usage period for heating divided by the total electric

power input during the same period.

— = Not Applicable.

F2RP/F2FP036 34.0 3.00 20.4 2.16 7.2 15.5 2.40 15.6 2.54 20.4 2.80 24.9 3.03 29.9 3.20 34.0 3.32 38.5 3.50

AHP36,42 34.0 3.00 20.4 2.16 7.2 15.5 2.40 15.6 2.54 20.4 2.80 24.9 3.03 29.9 3.20 34.0 3.32 38.5 3.50

F2FP048 37.0 3.08 31.4 2.32 7.5 20.8 3.64 26.1 3.80 31.4 3.97 36.7 4.13 40.1 4.27 47.0 4.47 54.6 4.71

AHP48,60 37.0 3.08 31.4 2.32 7.5 20.8 3.64 26.1 3.80 31.4 3.97 36.7 4.13 40.1 4.27 47.0 4.47 54.6 4.71

F2FP060 58.5 3.12 39.0 2.34 7.6 26.0 4.48 32.5 4.68 39.0 4.88 42.1 4.98 45.1 5.07 58.5 5.49 65.0 5.70

AHP48,60 58.5 3.12 39.0 2.34 7.6 26.0 4.48 32.5 4.68 39.0 4.88 42.1 4.98 45.1 5.07 58.5 5.49 65.0 5.70

3

HEATING PERFORMANCE - With Furnace Coils

UNIT

MODEL*

G2FD042(S,H)21 34.0 3.00 20.2 2.14 7.2 11.3 2.40 15.7 2.58 20.2 2.77 24.7 2.94 29.5 3.15 34.0 3.32 40.5 3.50

G1NA036S17L 35.0 3.20 22.0 2.26 7.6 13.3 2.62 17.7 2.74 22.0 2.85 23.3 2.71 24.5 2.57 35.0 3.21 39.3 3.32

G1NA048S21D 35.0 3.20 22.0 2.26 7.6 13.3 2.62 17.7 2.74 22.0 2.85 23.3 2.71 24.5 2.57 35.0 3.21 39.3 3.32

E1RA036S25,46

FC/MC/PC35*3X 34.0 3.00 20.2 2.14 7.2 11.3 2.40 15.7 2.58 20.2 2.77 24.7 2.95 29.5 3.15 34.0 3.32 40.5 3.50
FC/MC/PC/UC36*3X 34.03.0020.22.14 7.2 11.32.4015.72.5820.22.7724.72.9529.53.1534.03.3240.53.50
FC/MC/PC/UC42*3X 34.03.0020.22.14 7.2 11.32.4015.72.5820.22.7724.72.9529.53.1534.03.3240.53.50
G2FD048(S,H)21,24 47.0 3.02 31.2 2.32 7.5 21.0 3.56 26.1 3.75 31.2 3.94 36.3 4.13 40.1 4.32 47.0 4.56 54.1 4.59

G1NA048S21D 47.0 2.96 31.2 2.30 7.5 20.7 3.52 25.9 3.75 31.2 3.98 35.2 4.13 39.2 4.29 47.0 4.65 52.3 4.88

E2RA048S25,46

FC/MC/PC/UC48C3X47.03.0231.22.32 7.5 21.03.5626.13.7531.23.9436.34.1340.14.3247.04.5654.14.59
FC/MC/PC/UC48D3X47.03.0231.22.32 7.5 21.03.5626.13.7531.23.9436.34.1340.14.3247.04.5654.14.59

G2FD060(S,H)24 58.0 3.20 38.5 2.40 7.7 25.5 4.29 32.0 4.50 3.9 4.70 42.1 4.91 45.7 5.11 58.0 5.31 64.5 5.51

E1RA060S25,46

FC/MC/PC/UC60C3X 58.0 3.20 38.5 2.40 7.7 25.5 4.29 32.0 4.50 3.9 4.70 42.1 4.91 45.7 5.11 58.0 5.31 64.5 5.51
FC/MC/PC/UC60D3X 58.0 3.20 38.5 2.40 7.7 25.5 4.29 32.0 4.50 3.9 4.70 42.1 4.91 45.7 5.11 58.0 5.31 64.5 5.51

1. Rated CFM same as for cooling.

2. Heating MBH based on ARI standards of 70° DB entering indoor air, 72% RH outdoor air with 25 feet of interconnecting piping and no supplemental elec­tric heat operation.

3. Integrated heating capacities include the effect of defrost cycles in the temperature range where they occur.

COP equals MBH output divided by (total KW input x 3.412).
HSPF (Heating Seasonal Performance Factor) is the total heating output during a normal annual usage period for heating divided by the total electric

power input during the same period.

— = Not Applicable.

1

COIL

MODEL

G1UA048S21 34.03.0020.22.14 7.2 11.32.4015.72.5820.22.7724.72.9529.53.1534.03.3240.53.50
G1FA048S21 34.0 3.00 20.2 2.14 7.2 11.3 2.40 15.7 2.58 20.2 2.77 24.7 2.95 29.5 3.15 34.0 3.32 40.5 3.50

G1UA048S21 47.0 3.00 31.2 2.30 7.50 20.9 3.60 26.1 3.79 31.2 3.98 36.3 4.16 42.0 4.39 47.0 4.56 54.0 4.61
G1FA048S21 47.0 3.00 31.2 2.30 7.5 20.9 3.60 26.1 3.79 31.2 3.98 36.3 4.16 42.0 4.39 47.0 4.59 54.0 4.61

G1UA060S24 58.0 3.20 38.5 2.40 7.7 25.5 4.29 32.0 4.50 3.9 4.70 42.1 4.91 45.7 5.11 58.0 5.31 64.5 5.51
G1FA060S24 58.0 3.20 38.5 2.40 7.7 25.5 4.29 32.0 4.50 3.9 4.70 42.1 4.91 45.7 5.11 58.0 5.31 64.5 5.51

47°F17°F

MBH COP MBH COP STD MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW MBH KW

ARI HEATING

2

HSP

-3°F7°F17°F27°F37°F47°F57°F

F

OUTDOOR TEMP

3

6 Unitary Products Group

279104-YTG-B-0307

ACCESSORIES

Refer to Price Manual for specific model numbers.
Start Assist Kit (2SA067*)
Blower Time Delay - Available to increase efficiency when

installed. Installs on indoor section and maintains blower for
approximately one minute after cooling thermostat has been
satisfied.

Hard Start Kits - Provides required starting torque for use
with Thermal Expansion Valve Kit.

Low Temperature Cutout (2LT06700224) - Prevents heat
pump operation below -10°F ambient temperature.

Compressor Blanket - Designed to further reduce the nor­mal operating sound.

Add-on Fossil Fuel Control - Interface contro ls for use with
gas, oil furnaces and the heat pump system are available.

Thermal Expansion Valve Kit - 1TVM700 Series TXV kit
used to improve system performance.

Outdoor Thermostat (2TD06700124) - Provides additional
staging of supplemental electric heat.

TYPICAL INSTALLATION

Room Thermostats - A wide selection of matching thermo-

stats is available to provide features required for any installa­tion.

2H/1C, manual changeover electronic non-programmable
thermostat.

3H/2C, non-programmable digital thermostat.
3H/2C, auto/manual changeover, electronic programmable,

7-day, thermostat.
* For the most current accessory information, refer to the

price book or consult factroy.

SOUND POWER RATINGS*

UNIT

MODEL

018 80
024 80
030 80
036 82
042 82
048 77
060 82

* Rated in accordance with ARI 270-95 Standards.

(dBA)

60” OVERHEAD
CLEARANCE

10” CLEARANCE
COIL AREA

NOTE: ALL OUTDOOR WIRING
MUST BE WEATHERPROOF.

MINIMUM 24” SERVICE ACCESS
CLEARANCE ON ONE SIDE

WEATHERPROOF
DISCONNECT
SWITCH

CONTROL ACCESS PANEL

THERMOSTAT

TO FURNACE OR
AIR HANDLER
TERMINAL BLOCK

NEC CLASS 1 WIRING

NEC CLASS 2 WIRING

TO INDOOR COIL

SEAL OPENING(S) WITH
PERMAGUM OR EQUIVALENT

Unitary Products Group 7

279104-YTG-B-0307

TYPICAL FIELD WIRING - 3 PH (036 - 060)

ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES

THERMOSTAT

LOW VOLTAGE TERMINAL BLOCK
IN AIR HANDLER WITH ELECTRIC HEAT

R

BorC

Y

O

W

LorX

G

T

E

1

JUMPER TERMINALS E AND W TOHEAT
ON FIRST STAGE DURING EMERGENCY HEAT.

2

TERMINAL NOT USED ON ALL THERMOSTATS.

1

2

2

POWER WIRING
24V CONTROL WIRING

(NEC CLASS 2)

FIELD
INSTALLED
JUMPER

GND.

LUG

3

CHECK THE LOW VOLTAGE TERMINAL BLOCK ON THE INDOOR UNIT FOR THE ACTUAL ARRANGEMENT OF THE TERMINALS.

4

CONNECT POWER WIRING TO TERMINAL BLOCK 3TB ON UNITS WITHOUT ELECTRIC HEAT OR CIRCUIT BREAKER.

5

GRAY FOR USE WITH OPTIONAL OUTDOOR THERMOSTAT KITS.

INDOOR UNIT

R

BorC

Y

O

W2

G

W1

3,4

DEFROST
CONTROL

RED

BLK

YEL

ORG

BRN

PUR

WHT

5

GRY

208/230-3-60

R

C

Y

O

W

X

/66

W1

CC

POWER
SUPPLY

460-3-50

CONTACTOR

T3

T2

M

L3

L2

POWER WIRING

208/230-3-60

460-3-50

T1

L1

GND.

SCREW

OUTDOOR UNIT

TYPICAL FIELD WIRING - 3 PH (090)

ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES

THERMOSTAT

R

BorC

Y

O

W

X

G

T

E

1

JUMPER TERMINALS E AND W TOHEAT
ON FIRST STAGE DURING EMERGENCY HEAT.

2

TERMINAL NOT USED ON ALL THERMOSTATS.

3

TERMINAL NOT USED ON ALL THERMOSTATS.

1

2

2

FIELD
INSTALLED
JUMPER

POWER WIRING
24V CONTROL WIRING

(NEC CLASS 2)

3

CHECK THE LOW VOLTAGE TERMINAL BLOCK ON THE INDOOR UNIT FOR THE ACTUAL ARRANGEMENT OF THE TERMINALS.

4

CONNECT POWER WIRING TO TERMINAL BLOCK 3TB ON UNITS WITHOUT ELECTRIC HEAT OR CIRCUIT BREAKER.

5

REQUIRED ON ALL ELECTRIC HEAT

INDOOR UNIT

LOW VOLTAGE TERMINAL BLOCK
IN AIR HANDLER WITH ELECTRIC HEAT

R

C

Y

O

W

X

GND.

LUG

53

G

60

60

5

FIELD
INSTALLED
JUMPER

3,4

DEFROST
CONTROL

RED

BLK

YEL

ORG

BRN

PUR

WHT

208/230-3-60

R

C

Y

O

W

X

/66

W1

POWER
SUPPLY

460-3-50

CONTACTOR

T3

T2

M

L3

L2

POWER WIRING

208/230-3-60

460-3-50

T1

L1

GND.

SCREW

OUTDOOR UNIT

8 Unitary Products Group

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. E1RA036S(25,46)
INDOOR COIL MODEL NO. F2RP/F2FP036

CONDENSER

ENTERING AIR

TEMPERATURE

75

85

95

105

115

125

ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

NOTE:

ID CFM 1000 1250 1400

ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70

ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 38.1 35.0 32.5 29.4 38.6 35.5 32.9 29.9 38.8 35.7 33.2 30.2
S.C. 22.9 22.9 22.1 23.6 24.1 24.2 23.4 24.8 24.9 24.9 24.1 25.5

KW 3.15 3.08 3.02 2.94 3.16 3.10 3.03 2.96 3.17 3.10 3.04 2.97
T.C. 37.6 34.6 32.0 28.9 38.1 35.1 32.7 29.4 38.3 35.3 33.0 29.7
S.C. 23.3 23.4 22.6 23.9 24.8 24.9 24.1 25.3 25.7 25.7 25.0 26.1

KW 3.39 3.30 3.22 3.12 3.40 3.32 3.24 3.14 3.41 3.33 3.25 3.15
T.C. 36.2 33.3 30.9 27.7 36.7 33.7 31.4 28.3 36.8 34.0 31.6 28.6
S.C. 23.3 23.3 22.6 23.7 24.9 24.9 24.0 25.4 25.8 25.9 24.9 26.2

KW 3.71 3.60 3.51 3.38 3.72 3.62 3.53 3.40 3.74 3.64 3.55 3.42
T.C. 34.4 31.5 29.2 26.3 34.7 32.0 29.6 26.8 35.0 32.2 29.9 27.3
S.C. 22.9 22.9 22.1 23.3 24.5 24.5 23.5 24.7 25.6 25.5 24.6 25.5

KW 4.03 3.90 3.79 3.63 4.06 3.93 3.82 3.67 4.06 3.94 3.82 3.71
T.C. 32.2 29.6 27.4 24.7 32.6 30.0 27.8 25.5 32.8 30.2 28.1 25.8
S.C. 22.2 22.2 21.4 22.4 23.9 23.8 22.9 23.8 24.8 24.8 23.8 24.1

KW 4.34 4.19 4.05 3.88 4.37 4.22 4.09 3.93 4.38 4.24 4.10 3.96
T.C. 30.0 27.7 25.6 23.1 30.5 28.0 26.0 24.2 30.6 28.2 26.3 24.3
S.C. 21.5 21.5 20.6 21.5 23.3 23.1 22.2 22.9 24.0 24.1 23.1 22.7

KW 4.65 4.48 4.31 4.13 4.68 4.51 4.36 4.19 4.70 4.54 4.38 4.21

279104-YTG-B-0307

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the

listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.

Air Handler Coil

MA12BN2,4 FC/MC35B3X 1.01 1.02 1.01
MA12BN2,4 FC/MC36B3X 1.01 1.02 1.01
MA12BN2,4 FC/MC42B3X 1.01 1.02 1.01
MA12BN2,4 G2FD042(S,H)21 1.01 1.02 1.01
AHP42C3X – 1.00 1.00 1.00
F2RP/F2FP042 – 1.00 1.00 1.00
– G1FA048S21 1.01 0.99 1.01
– G1NA036S17L 1.03 1.05 1.03
– G1NA048S21D 1.03 1.05 1.04
– FC/MC/PC35*3X 1.01 0.99 1.01
– FC/MC/PC/UC36*3X 1.01 0.99 1.01
– FC/MC/PC-UC42*3X 1.01 0.99 1.01
– G1UA048S21 1.01 0.9 9 1.01
– G2FD042(S,H)21 1.01 1.02 1.01

T.C. S.C. KW

Unitary Products Group 9

279104-YTG-B-0307

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. E2RA048S(25,46)
INDOOR COIL MODEL NO. F2FP048

CONDENSER

ENTERING AIR

TEMPERATURE

75

85

95

105

115

125

ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

NOTE:

ID CFM 1300 1450 1550
ID DB (°F) 85 80 75 70 85 80 75 70 85 80 75 70
ID WB (°F) 72 67 62 57 72 67 62 57 72 67 62 57

T.C. 52.3 48.3 45.0 40.6 53.0 49.0 45.7 41.3 53.4 49.4 46.1 41.9

S.C. 32.5 32.8 31.7 33.5 34.0 34.3 33.2 35.1 35.0 35.2 34.1 36.3

KW 4.14 4.07 4.02 3.95 4.16 4.08 4.04 3.97 4.17 4.09 4.05 3.97

T.C. 50.9 47.0 43.7 39.4 51.5 47.6 44.4 40.3 51.9 48.0 44.7 40.6

S.C. 32.4 32.6 31.6 33.3 34.0 34.2 33.2 35.1 35.2 35.4 34.2 36.2

KW 4.44 4.36 4.30 4.22 4.46 4.38 4.32 4.24 4.47 4.38 4.33 4.25

T.C. 48.8 45.0 41.8 37.9 49.2 45.5 42.4 38.4 49.6 45.8 42.7 38.7

S.C. 32.0 32.2 31.2 32.9 33.6 33.8 32.9 34.5 34.9 35.1 33.8 35.6

KW 4.87 4.79 4.73 4.64 4.90 4.81 4.74 4.66 4.91 4.81 4.76 4.67

T.C. 46.1 42.5 39.5 35.8 46.6 43.0 40.1 36.3 46.4 43.3 40.4 36.7

S.C. 31.0 31.1 30.1 32.0 32.9 32.9 31.9 33.7 33.8 34.3 32.9 35.1

KW 5.37 5.28 5.22 5.12 5.38 5.30 5.22 5.14 5.34 5.30 5.24 5.14

T.C. 43.2 39.9 37.0 33.5 43.6 40.3 37.6 34.2 43.8 40.6 37.9 35.0

S.C. 29.9 30.2 29.2 30.7 31.8 32.1 30.8 32.8 32.9 33.1 31.8 34.5

KW 5.90 5.80 5.74 5.66 5.90 5.80 5.76 5.66 5.92 5.83 5.78 5.68

T.C. 40.3 37.3 34.6 31.2 40.6 37.6 35.0 32.1 41.2 37.9 35.3 33.3

S.C. 28.8 29.3 28.2 29.4 30.7 31.3 29.7 31.9 32.0 31.9 30.8 33.9

KW 6.43 6.32 6.27 6.20 6.42 6.30 6.31 6.18 6.50 6.36 6.31 6.22

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the

listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.

Air Handler Coil

MA16CN2,4 FC/MC48C3X 1.00 1.00 0.97
N1AHC1646 G2FD048(S,H)21 1.00 1.00 0.97
MA20DN2,4 FC/MC48D3X 1.00 1.00 0.97
N1AHD2046 G2FD048(S,H)24 1.00 1.00 0.97
AHP/SHP48D3X – 1.02 1.01 1.02
F2FP060 – 1.02 1.01 1.02
– G1FA048S21 1.00 0.97 0.98
– G1NA048S21D 0.99 0.93 0.95
– G1UA048S21 1.00 0.97 0.98
– FC/MC/PC/UC48C,D3X 1.00 1.00 0.97
– G2FD048(S,H)21,24 1.00 1.00 0.97

T.C. S.C. KW

10 Unitary Products Group

COOLING PERFORMANCE DATA

AIR CONDITIONER MODEL NO. E1RA060S(25,46
INDOOR COIL MODEL NO. G2FD060(S,H)24

CONDENSER

ENTERING AIR

TEMPERATURE

65

75

85

95

105

115

ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

NOTE:

ID CFM 1600 1800 2000

ID DB (°F) 85 80 75 85 80 75 85 80 75

ID WB (°F) 71 67 63 71 67 63 71 67 63

T.C. 63.0 61.1 60.7 62.9 60.9 61.1 62.9 60.6 61.4
S.C. 39.6 39.7 40.3 41.6 41.5 42.2 43.7 43.3 44.1

KW 3.71 3.66 3.68 3.71 3.66 3.67 3.71 3.67 3.67
T.C. 62.3 59.8 57.9 62.5 60.0 58.5 62.6 60.1 59.0
S.C. 39.6 39.3 39.1 41.8 41.3 41.1 43.9 43.3 43.1

KW 4.20 4.14 4.12 4.21 4.15 4.13 4.21 4.16 4.13
T.C. 61.7 58.5 55.1 62.0 59.1 55.9 62.3 59.6 56.6
S.C. 39.6 38.9 38.0 41.9 41.1 40.1 44.2 43.3 42.2

KW 4.70 4.63 4.57 4.71 4.64 4.58 4.72 4.65 4.60
T.C. 61.0 57.2 52.3 61.5 58.2 53.3 62.0 59.1 54.2
S.C. 39.6 38.5 36.8 42.0 40.9 39.0 44.4 43.3 41.2

KW 5.19 5.11 5.01 5.21 5.13 5.04 5.22 5.14 5.06
T.C. 58.3 53.9 49.1 59.1 54.7 49.9 60.0 55.6 50.7
S.C. 38.5 37.2 35.4 41.0 39.6 37.6 43.6 41.9 39.8

KW 5.78 5.67 5.55 5.80 5.69 5.57 5.82 5.71 5.60
T.C. 55.5 50.5 45.9 56.8 51.3 46.5 58.0 52.1 47.1
S.C. 37.4 35.9 34.0 40.1 38.2 36.2 42.7 40.5 38.3

KW 6.36 6.22 6.08 6.39 6.25 6.11 6.41 6.27 6.13

279104-YTG-B-0307

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the

listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.

Air Handler Coil

MA20DN2,4 FC/MC60D3X 1.00 1.00 1.00
N1AHD2046 G2FD060(S,H)24 1.00 1.00 1.00
AHP/SHP60D3X – 0.98 0.98 1.02
F2FP060 – 0.98 0.98 1.02
– G1FA060S21,24 1.00 1.00 1.00
– G1UA060S21,24 1.00 1.00 1.00
– FC/MC/PC/UC60*3X 1.00 1.00 1.00

T.C. S.C. KW

Unitary Products Group 11

279104-YTG-B-0307

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO E1RA036S(25,46)
EVAPORATOR COIL MODEL NO F2RP/F2FP036

AIR TEMP.
ENTERING
OUTDOOR

UNIT

60

47

40

30

17

10

ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

NOTE:

AIR TEMP.

ENTERING

INDOOR

COIL

60 41.63.373.6242.03.303.7341.33.273.70
70 39.13.543.2440.23.493.3740.23.493.38
80 37.43.702.9739.13.673.1239.73.693.16
60 35.33.173.2635.73.153.3234.83.153.24
70 33.13.322.9334.03.323.0033.83.332.98
80 31.53.462.6732.73.482.7633.33.492.80
60 30.23.022.9431.23.033.0231.93.053.08
70 28.73.142.6829.53.162.7430.43.182.81
80 27.13.282.4327.93.302.4828.93.322.55
60 26.12.892.6527.42.932.7427.52.962.73
70 24.42.962.4225.83.012.5126.13.042.51
80 22.43.072.1423.83.132.2324.33.162.25
60 21.42.662.3621.92.712.3722.02.742.36
70 19.72.732.1220.42.792.1520.72.822.15
80 18.02.791.8918.92.861.9419.32.891.96
60 18.12.502.1218.82.562.1619.12.602.16
70 16.52.551.9017.42.621.9517.72.661.96
80 14.82.581.6815.82.651.7516.22.691.77

MBTUH KW C.O.P. MBTUH KW C.O.P. MBTUH KW C.O.P.

1000 1250 1400

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

MA12BN2,4 FC/MC35B3X 1.01 1.02 1.01
MA12BN2,4 FC/MC36B3X 1.01 1.02 1.01
MA12BN2,4 FC/MC42B3X 1.01 1.02 1.01
MA12BN2,4 G2FD042(S,H)21 1.00 1.00 1.00
AHP42C3X – 1.00 1.00 1.00
F2RP/F2FP042 – 1.00 1.00 1.00
– G1FA048S21 1.00 1.00 1.00
– G1NA036S17L 1.03 0.97 1.07
– G1NA048S21D 1.03 0.97 1.07
– FC/MC/PC35*3X 1.01 0.99 1.01
– FC/MC/PC/UC36*3X 1.01 0.99 1.01
– FC/MC/PC-UC42*3X 1.01 0.99 1.01
– G1UA048S21 1.00 1.00 1.00
– G2FD042(S,H)21 1.00 1.00 1.00

MBH KW COP

12 Unitary Products Group

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO E2RA048S(25,46)
EVAPORATOR COIL MODEL NO F2RP/F2FP048

AIR TEMP.
ENTERING
OUTDOOR

UNIT

60

47

40

30

17

10

ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

NOTE:

AIR TEMP.

ENTERING

INDOOR

COIL

60 53.44.863.2352.94.723.2852.24.253.61
70 54.24.763.3454.14.613.4453.74.143.80
80 54.15.572.8554.45.392.9654.44.833.30
60 47.04.543.0346.64.453.0746.54.053.36
70 46.94.563.0247.04.473.0847.24.063.41
80 46.35.242.5946.95.132.6847.34.652.98
60 37.73.543.1242.94.312.9243.43.933.24
70 37.33.982.7542.94.402.8642.64.133.02
80 36.65.791.8542.55.002.5040.05.472.14
60 37.74.012.7638.74.032.8237.93.703.00
70 36.74.162.5838.24.222.6538.43.932.86
80 35.34.602.2537.34.702.3338.74.442.55
60 32.23.672.5732.73.682.6133.03.402.85
70 30.83.982.2731.43.972.3231.83.662.55
80 29.44.302.0030.14.292.0630.63.942.28
60 29.23.462.4829.63.462.5130.13.192.77
70 27.53.812.1227.93.802.1528.43.512.37
80 25.84.021.8826.34.021.9226.73.712.12

MBTUH KW C.O.P. MBTUH KW C.O.P. MBTUH KW C.O.P.

1250 1400 1550

279104-YTG-B-0307

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

MA16CN2,4 FC/MC48C3X 1.00 1.00 0.97
N1AHC1646 G2FD048(S,H)21 1.00 1.02 0.98
MA20DN2,4 MC48D3X 1.00 1.02 0.98
N1AHD2046 G2FD048(S,H)24 1.00 1.02 0.98
AHP/SHP48D3X – 1.01 1.02 0.99
F2FP060 – 1.01 1.02 0.99
– G1FA048S21 1.00 1.02 0.98
– G1NA048S21D 1.00 1.04 0.96
– G1UA048S21 1.00 1.03 0.97
– FC/MC/PC/UC48C,D3X 1.00 1.03 0.97
– G2FD048(S,H)21,24 1.00 1.03 0.97

MBH KW COP

Unitary Products Group 13

279104-YTG-B-0307

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO E1RA060S(25,46)
EVAPORATOR COIL MODEL NO G2FD060(S,H)24

AIR TEMP.
ENTERING
OUTDOOR

UNIT

60

47

40

30

17

10

ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

NOTE:

AIR TEMP.

ENTERING

INDOOR

COIL

60 63.65.093.6761.94.983.6460.14.873.62
70 64.85.333.5663.55.183.5962.25.043.62
80 65.95.603.4565.15.393.5464.25.203.62
60 56.94.154.0355.74.024.0654.43.904.10
70 58.34.623.7058.04.543.7556.34.353.80
80 59.75.193.3859.05.033.4458.24.883.50
60 54.54.053.9553.33.933.9752.03.814.00
70 53.74.413.5753.44.323.6353.24.223.69
80 52.94.873.1953.64.783.2954.34.713.38
60 49.63.893.7449.83.803.8449.93.723.93
70 47.74.183.3448.04.103.4448.44.023.53
80 45.84.572.9446.34.473.0446.84.393.13
60 40.63.563.3441.03.513.4241.33.463.50
70 38.83.862.9439.23.803.0239.73.743.11
80 36.94.262.5437.54.182.6338.04.102.71
60 36.3 3.53 3.01 36.7 3.46 3.11 37.1 3.38 3.21
70 34.33.822.6334.73.742.7235.23.672.81
80 32.24.192.2532.74.122.3333.24.052.40

MBTUH KW C.O.P. MBTUH KW C.O.P. MBTUH KW C.O.P.

1600 1800 2000

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handler Coil

MA20DN2,4 FC/MC60D3X 1.00 1.00 1.00
N1AHD2046 G2FD060(S,H)24 1.00 1.00 1.00
AHP/SHP60D3X – 1.01 1.03 0.98
F2FP060 – 1.01 1.03 0.98
– G1FA060S21,24 1.00 1.00 1.00
– G1UA060S21,24 1.00 1.00 1.00
– FC/MC/PC/UC60*3X 1.00 1.00 1.00

MBH KW COP

14 Unitary Products Group

NOTES

279104-YTG-B-0307

Unitary Products Group 15

NOTES

Subject to change without notice. Printed in U.S.A. 279104-YTG-B-0307
Copyright © by York International Corp. 2007. All rights reserved. Supersedes: 279104-YTG-A-1106

Unitary 5005 Norman
Product York OK
Group Drive 73069