YOKOGAWA AR-SP User's Manual

User’s
Manual

IM AR07-01E

Model AR-SP
Arrester for three-wire
system pulse signal
(50V DC or less)

Scott

Please read through this Manual before using the arresters for correct
handling.
Please keep this Manual carefully after use.

2nd Edition Sep. 2001 (MC)

1.

Cautionary Notes for Safe Use of the Product

IM AR07-01E

For the correct use of this product,read through this manual before
use.The following safety symbol is indicated on the product to ensure
safe use.

If this symbol is indicated on the product, the operator
should refer to the explanation given in the instruction
manual in order to avoid personnel injury or death to either
themselves or other personnel, and/or damage to the in­strument. The manual describes the special care the opera­tor should exercise to avoid shock or other dangers that
may result in injury or loss of life. The following symbol
marks are used only in this manual.

Musashino Center Bldg.
1-19-18, Naka-cho Musashino-shi, Tokyo 180-0006 Japan
Phone: [phone] Facsimile: [phone]

●FRK-16 (Panel)

19

24.5

89

99

73

2.2 External Dimensions

23.5

483

465

36-M4 8-ø5.5⫻10

441.6

55

28.5

26.5

Unit : mm

(8.5) (3.8)

Oval hole

50

24.7

76.2

16.5

IMPORTANT

Indicates that operating the hardware or software in a
particular manner may damage it or result in a system
failure.

NOTE

Draws attention to information that is essential for
understanding the operations and/or features of the
product.

2. Mounting and Wiring

WARNING

Wiring should be done after ensuring the break of each
cable.

2.1 Mounting

Mount the arrester referring the figure below.

24

90

Panel

M4 screw

100

90

Main body

Terminal base

2.3 Terminal Arrangement

A

B

C

Use AR-SP

Protect side
terminal B ⫹
C –

3

Surge side 1 ⫹

1

2

terminal 2 ⫹
3 –

Terminal

A ⫹

2.4 Wiring

IMPORTANT

●

Use of arresters ignoring the specifications may cause
electric shock, overheating or damage.
(a) Input signal value applied to the arrester should

meet the required specifications.

(b) The external wiring to the terminals and wiring to

ground are as specifications.

●

High voltage is applied on the terminals of arresters for
pulse signal during power on, as shown in the figure
below. Do not touch the terminals.

AR8
DIN rail adapter

No.

104

CAUTION FOR HIGH VOLTAGE

50V DC

Flexible twisted wire and durable round crimp-on terminal (JIS C2805)
are recommended to use.

(1) Signal cable
Nominal cross-sectional area of conductor: 0.5 to 0.75 mm2.
Example of suitable cable:
Vinyl code (VJF) (JIS C3306) for electronic instrument.
(2) Grounding cables
Nominal cross-sectional area of conductor:

2.0 mm2 or more for grounding.
Example of suitable cable:
600V vinyl insulated cable (IV) (JIS C3307),
Vinyl insulated cable (KIV) (JIS C3316) for electronic instrument

4. Environmental Conditions

Ambient temperature: 0 to 50°C
Relative humidity: 5 to 90%RH (No condensation)
Altitude at installation site: Max.2000m above sea level
Installation category based on EN61010-1: II (see Note.)

NOTE

The “Installation Category” implies the regulation for
impulse withstand voltage.It is also called the “Overvoltage
category”.“ II ” applies to electrical equipment.“Pollution
level” describes the degree to which a solid,liquid or gas
which deteriorates dielectric strength is adhering.“2”
applies to a normal indoor atmosphere.

5. Maintenance

5.1 Arrester main body replacement

The arrester main body and terminal base are connected by plug-in.
Circuit between surge side and protect side would not be open even if
the main body is removed from the socket on terminal base by loosing
mounting screw. So the arrester main body can easily be replaced with
new one.

2.5 Grounding

Interconnect the ground terminals of the arrester and the instrument to
be protected. Touch ground from the arreter side as shown in the figure
below. Install the arrester and instrument as close as possible, and
make the cable as short as possible. The wires for interconnect ground­ing should have lower effective resistance than ground resistance.
Ground resistance should be 100 Ω or less. (JIS Class 3 grounding)

NOTE

Wire tightening torque for arrester should not be 1.2 N•m or
more.

(1) Interconnect Grounding

Arrester

Instrument

(2) Interconnect Grounding
(when using shield line)

Arrester

Grounding for serial installation of arresters is to
connect ground terminal board in zigzag and
touch ground at one point from last arrester
according to JIS Class 3 grounding.
Grounding wire should be 2.0 mm

Instrument

2

or more.

NOTE

●

When replacing the arrester main body, make sure that
the model and suffix codes indicated on the labels of
the main body and terminal base are the same.

●

When replacing the arrester main body having
specifications of surge discharge withstand current
rating of 5000A, make sure that the style code indicated
on the label of terminal base is “S2.0”. If mounted to the
terminal base of style code “S1.0”, the specifications of
the arrester main body can not be satisfied, because the
surge discharge withstand current rating will be for
1000A specifications. To operate the arrester for 5000A
specifications, the replacement of terminal base is also
required.

5.2 Arrester checking

To check the arrester performance, remove main body from the socket
and check it by using the checker (option). Replace the main body if re­quired.

5.3 Arrester check period

To protect the instrument from damage by induced lightning, the arrester
should be checked periodically at least once a year. In areas where
lightning occurs frequently, check should be done more often particularly
after thunderstorms.

6. Hardware Specification

Permissible current leakage
Instrument side voltage limit

Ground terminal board

3.

Connection of Arresters with Instruments to be Protected

Pulse generator

⫹V

Puls

signal

COM

JIS Class 3 grounding

AR-SP AR-SP

Lightning surge

AC1
B2

3

Ground terminal Ground terminal

Ground Ground

13A
2B

C

Pulse signal

transmitter

GND

(at 10 kV, 1.2/50 ␮s)
Suge discharge withstand capacity

(at 8/20 ␮s)
Discharge starting voltage

Safety standards

- 2 -

Between lines
Between ground
Between lines
Between ground
Between lines
Between ground
Between lines
Between ground

Conforms to EN61010-1 Installation Category II

10 ␮A or less (at 50 V DC)
10 ␮A or less (at 50 V DC)
90 V or less
250 V or less
1000 A
5000 A
74 V or more
74 V or more

IM AR07-01E 2nd Edition Sep.5 2001-00