
YETTER MANUFACTURING CO.
FOUNDED 1930
Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website: www.yetterco.com
E-mail: info@yetterco.com

INSTALLATION / ASSEMBLY INSTRUCTIONS
STYLE 1. Attaching drag
chain kit to closing wheel arm
with bolt on wheels. Discard
two of the flat washers or
spacer if necessary and install
the bracket as shown in
drawing to the left. Note:
Keep the 1 x 12 closing wheels
spaced 1 ¼”-1 ½” apart and
the spike wheels spaced 2” – 2
½” apart. Securely tighten
hardware.
STYLE 2. Attaching drag chain kit to
closing wheel arm without holes or
bolt on wheels. Drill a 13/32” hole on
each side of arm. Locate hole as
shown in drawing to the right. Using
3/8” x 1” hex bolt, flat washer and
locknut, attach brackets as shown.
Securely tighten hardware.
STYLE 3. Attaching drag chain
kit to closing wheel arm with
holes provided. Attach brackets
as shown in drawing to the left
using 3/8” x 1” hex bolt, flat
washer and locknut. Securely
tighten hardware.
Adjustments:
soil. Securely tighten hardware. For best soil leveling, keep front end of the
chain as low as possible while maintaining clearance above the soil for the
bracket ends. Use drag chains when planting in minimum till or in no-till where at
least some of the soil surface is dry.
NOTE: As with any type of furrow closing devise it is advisable to do in field
checks and make adjustments as necessary. There is no substitute for visual
inspection to verify that the seed is being properly placed. Careful attention is
required when using herbicide and/or insecticide, consult your chemical provider
for compatibility.
Position brackets to carry front of chain about 3” to 4” above

6200-108 DRAG CHAIN
APPLICATION CHART
40 MM
BEARING
BOLT ON
MAKE MODEL
YETTER
JOHN DEERE
6000-002 X MOUNT TO WHEEL BOLT
7000/ME X MOUNT TO HOLES IN ARM
7200/ME II X MOUNT TO HOLES IN ARM
WHEEL
1700/ME II
KINZE
PLUS X MOUNT TO WHEEL BOLT
PRE-1993 X DRILL HOLES
1993-
WHITE
PRESENT X MOUNT TO WHEEL BOLT
5100 X MOUNT TO HOLES IN ARM
6100 X MOUNT TO WHEEL BOLT
8000 X MOUNT TO WHEEL BOLT
WATER PUMP
BEARING W/
HOLES IN ARM
WATER PUMP
BEARING W/O
HOLES IN ARM
BOLT ON
WHEEL
HOLES IN
ARM
WHERE TO ATTACH 6200-108
DRAG CHAIN
GREAT PLAINS
LANDOLL/DEUT
Z-ALLIS
MONOSEM
SHOUP
ALL X MOUNT TO WHEEL BOLT
ALL N/A N/A N/A N/A N/A
NG PLUS X MOUNT TO WHEEL BOLT
CW 7050 X MOUNT TO HOLES IN ARM
CW 3000 X MOUNT TO HOLES IN ARM
CASE/ NEW
HOLLAND ALL N/A N/A N/A N/A N/A
TROUBLE SHOOTING
PROBLEM
Drag chain not doing much
Drag chain gets caught on
spike wheel or chain bracket
SOLUTION
Chain bracket needs to be 3” –
4” above soil so more of chain
contacts soil
Install Residue Manager
Install a deflector. Weld a “U”
shaped bar of round rod to the

top rear corner of the 6200-338 mounting bracket.
Our name
Is getting known
Just a few years ago, Yetter products were sold primarily to the
Midwest only. Then we embarked on a program of expansion and
moved into the East, the South, the West and now north into
Canada. We’re even getting orders from as far away as Australia
and Africa.
So, when you buy Yetter products . . .you’re buying a name that’s
recognized. A name that’s known and respected. A name that’s
become a part of American agriculture and has become
synonymous with quality and satisfaction in the field of conservation
tillage.
Thank you.
YETTER MANUFACTURING CO.
Colchester, IL 62326-0358 309/776-4111
Toll Free 800/447-5777
Fax 309/776-3222
Website: www.yetterco.com
E-mail: info@yetterco.com
2565-715_REV_A 3/09