How it Works
Yazoo/Kees
Loading...
ZMKW52212
User Manual
68 pgs1.58 Mb0
User Manual
30 pgs849.68 Kb0
Table of contents
Loading...

Yazoo/Kees ZMKH52252, ZMKH61252, ZMKW48172, ZMKW52212, ZMKW48192 User Manual

Operator Manual
ZMKW52212 / 968999660
ZMKH52252 / 968999661
ZMKH61252 / 968999662 ZMKW48172 / 968999730 ZMKW48192 / 968999779
Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine.
©2008 HTC. All rights reserved.
Beatrice, NE. Printed in U.S.A.
CONTENTS
INTRODUCTION ...................................................................5
SYMBOLS AND DECALS ....................................................7
SAFETY ................................................................................9
SETUP AND ADJUSTMENTS ............................................18
CONTROLS ........................................................................22
OPERATION .......................................................................29
Jumper cables ............................................................32
MAINTENANCE ..................................................................38
Engine oil ....................................................................38
Blade replacement......................................................39
Leveling ......................................................................42
Cutting height adjustments .........................................42
Anti-scalp rollers .........................................................42
LUBRICATION ....................................................................44
TROUBLESHOOTING ........................................................48
STORAGE ...........................................................................50
CONFORMITY CERTIFICATES .........................................51
TECHNICAL DATA .............................................................52
SERVICE JOURNAL ..........................................................59

INTRODUCTION

Congratulations
Thank you for purchasing a Yazoo/Kees ride-on
mower. This machine is built for superior efciency
to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance.
This manual is a valuable document. Read the contents carefully before using or servicing the machine. The following of instructions (use, service, maintenance) by all who operate this machine is important for the safety of the operator and others. It can also considerably increase the life span of the machine and increase its resale value.
If you sell your machine, be sure to give the operator’s manual to the new owner.
Ensure that service and repair work are documented. A well-kept service journal reduces service costs for the maintenance and affects the machine’s resale value. Please contact your dealer for more information.

General

In this operator’s manual, left and right, backward and forward are used in relation to the machine’s normal driving direction.
Continuous dedication to improve our products require
that specications and design are subject to change
without notice.

Driving and Transport on Public Roads

Check applicable road trafc regulations before
transporting on public roads. If the machine is transported, you must always use approved fastening equipment and ensure that the machine is well anchored. DO NOT operate this machine on public roadways.

Towing

Do not tow this machine, it may cause damage to the drive system.
Do not tow any trailers, etc. with this mower. They may jackknife or overturn causing damage to the mower and possible serious injury to the operator.

Operating

This machine is constructed only for mowing grass on lawns and even ground without obstacles such as stones or tree stumps. The machine can also be used for other tasks when equipped with special accessories provided by the manufacturer. Operating instructions for the accessories are provided with delivery. All other types of uses are incorrect. The manufacturer’s directions concerning operation, maintenance, and repairs must be carefully followed.
Lawn mowers and all power equipment, can be potentially dangerous if used improperly. Safety requires good judgement, careful use in accordance with these instructions and common sense.
The machine must only be operated, maintained, and repaired by persons familiar with the machine’s special characteristics and who are also knowledgeable about the safety instructions. Use only approved repair parts to maintain this machine.
Accident prevention regulations, other general safety
regulations, occupational safety rules, and trafc
regulations must be followed without fail.
Unauthorized modications to the design of the
machine may absolve the manufacturer from liability for any resulting personal injury or property damage.
English-5
INTRODUCTION

Good Service

Yazoo/Kees’s products are sold only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your
retailer. See the certicate in the Service Journal in this
operator’s manual. When you need spare parts or support in service
questions, warranty issues, etc., please consult the following professional:
This Operator’s Manual belongs to the machine with the manufacturing number:

Manufacturing Number

The machine’s manufacturing number can be found
on the printed plate afxed to the left in the engine
compartment. Stated on the plate, from the top are:
The machine’s type designation (I.D.).• The manufacturer’s type number (Model).• The machine’s serial number (Serial no.)•
Please have the type designation and serial number available when ordering spare parts.
The engine’s manufacturing number is stamped on one of the valve covers.
The plate states:
The engine’s model.• The engine’s type.• Code•
Please have these available when ordering spare parts.
The Hydro Drive IZT gears have a barcode decal
afxed to the rear of the gears.
Engine
Transmission
English-6

SYMBOLS AND DECALS

P
These symbols are found on the machine and in the operator’s manual.
Study them carefully so that you know what they mean.
WARNING! Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx
xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx.
Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the manual.
R
Reverse Neutral Fast Slow Choke Fuel
N
IMPORTANT INFORMATION Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx
xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx.
Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly.
Warning! Parking Brake CE conformity Warning! Rotating blades, Do not touch parts marking. Only for keep away from the European market discharge deck
Battery acid is corrosive, explosive and ammable Do not stand here
Noise emissions to the surroundings in accordance with the European Union’s directive. The machine’s emission is stated in the chapter TECHNICAL DATA and on the decals.
Only machines for European
Use protective glasses Use protective gloves
market
English-7
SYMBOLS AND DECALS
Read Shut off engine and Keep a safe Use on slopes No passengers Operator’s remove key before distance from no greater Manual performing any the machine than 10° maintenance or repair work
Whole body Severing of ngers Do not open or Careful backing up, Careful going
exposure to and toes remove safety watch for other forward, watch for thrown objects shields while people other people engine is running
English-8
Moving sharp blades under cover

SAFETY

These instructions are for your safety. Read them carefully.
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

General Operation

Read, understand, and follow all instructions on • the machine and in the manual before starting.
Do not put hands or feet near rotating parts or • under the machine. Keep clear of the discharge opening at all times.
Only allow responsible adults, who are familiar • with the instructions, to operate the machine.
Clear the area of rocks, toys, wire and such • objects that could be picked up and thrown by the blades.
Be sure the area is clear of bystanders before • operating. Stop machine if anyone enters the area.
Never carry passengers. The machine is only • intended for use by one person.
Do not mow in reverse unless absolutely • necessary. Always look down and behind before and while backing.
Never direct discharged material toward • anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces.
Do not operate machine without the entire • grass catcher, discharge guard, or other safety devices in place and working
Slow down before turning.• Never leave a running machine unattended. •
Always turn off blades, set parking brake, stop engine, and remove keys before dismounting.
Disengage blades when not mowing. Shut • off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge guard.
Operate machine only in daylight or good •
articial light. Do not operate the machine while under the •
inuence of alcohol or drugs. Watch for trafc when operating near or •
crossing roadways.
WARNING! This symbol means that important safety
instructions need to be emphasized. It concerns your safety.
8011-512
Read the operator’s manual before starting the machine
8011-513
Clear the area of objects before mowing
English-9
SAFETY
Use extra care when loading or unloading the • machine into a trailer or truck.
Always wear eye protection when operating • machine.
Data indicates that operators, age 60 years and • above, are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.
Follow the manufacturer’s recommendation for • wheel weights or counterweights.
Anyone who operates this machine must rst •
read and understand this Operation Manual. Local laws may regulate the age of the user.
Keep machine free of grass, leaves or other • debris buildup which can touch hot exhaust or engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause buildup to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage.
8011-520
Never take passengers
WARNING! Engine exhaust and certain vehicle
components contain or emit chemicals considered to cause cancer, birth defects, or other reproductive system damage. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.
English-10
SAFETY

Personal Safety Equipment

Make sure that you have rst aid equipment •
close at hand when using the machine.Never use the machine when barefoot.
Always wear protective shoes or boots, • preferably with steel toe caps.
Always wear approved protective glasses or a • full visor when assembling or driving.
Always wear gloves when handling the blades.• Never wear loose clothing that can get caught •
in moving parts. Use ear protectors to avoid damage to hearing.•

Slope Operation

Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
Mow up and down slopes (10 degrees • maximum), not across.
Watch for holes, ruts, bumps, rocks, or other • hidden objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles.
Choose a low ground speed so that you will not • have to stop while on the slope.
Do not mow on wet grass. Tires may lose • traction.
Avoid starting, stopping, or turning on a slope. • If the tires lose traction, disengage the blades and proceed slowly straight down the slope.
Keep all movement on the slopes slow and • gradual. Do not make sudden changes in speed or direction, which could cause the machine to roll over.
Use extra care while operating machine with • grass catchers or other attachments; they can affect the stability of the machine. Do not use on steep slopes.
Do not try to stabilize the machine by putting • your foot on the ground.
Do not mow near drop-offs, ditches, or • embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in.
WARNING! When using the machine, approved personal
protective equipment (shown in illustrations) shall be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment.
8011-670a
Personal protective equipment
6003-004-01
Mow up and down, not side to side
WARNING! Do not drive up or down hills with slopes
greater than 10 degrees. And do not drive across any slopes.
English-11
SAFETY
Children Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.
Keep children out of the mowing area and in • the watchful care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters • the area.
Before and while backing, look behind and • down for small children.
Never carry children, even with the blades shut • off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine.
Never allow children to operate the machine.• Use extra care when approaching blind •
corners, shrubs, trees, or other objects that may block your view of a child.
8011-509
Be extra cautious when driving on slopes
English-12
8011-517
Never allow children to operate the machine
8011-518
Keep children away from work area
SAFETY

Safe Handling of Gasoline

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is
extremely ammable and the vapors are explosive.
Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
Use only approved gasoline container.
Never remove gas cap or add fuel with the • engine running. Allow engine to cool at least two (2) minutes before refueling.
Never fuel the machine indoors.• Never store the machine or fuel container •
where there is an open ame, spark, or pilot
light such as on a water heater or other appliances.
Before you begin refueling, minimize the risk of • static electricity by touching a metal surface.
Never ll containers inside a vehicle or on a •
truck or trailer bed with plastic liner. Always place containers on the ground away from your
vehicle when lling.
Remove gas-powered equipment from the • truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the • fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock­open device.
If fuel is spilled on clothing, change clothing • immediately.
Never overll fuel tank. Replace gas cap and •
tighten securely. Do not start the engine near spilled fuel.• Never use gasoline as a cleaning agent.• If leaks arise in fuel system, engine must not •
be started until problem has been resolved. Check the fuel level before each use and leave •
space for the fuel to expand, because the heat from the engine and the sun may otherwise
cause the fuel to expand and overow.
WARNING! The engine must not be started when the
driver’s oor plate or any protective plate for
the mower deck’s drive belt is removed.
8011-516
Never ll the fuel tank indoors
WARNING! The engine and the exhaust system, become
very hot during operation. Risk for burns if touched. Allow engine and exhaust system to cool at
least two (2) minutes before refueling.
English-13

General Maintenance

Never operate machine in a closed area.• Keep all nuts and bolts tight to be sure the •
equipment is in safe working condition. Never tamper with safety devices. Check their •
proper operation regularly. Keep machine free of grass, leaves, or other •
debris buildup. Clean oil or fuel spillage and remove any fuel-soaked debris. Allow machine to cool before storing.
If you strike a foreign object, stop and inspect • the machine. Repair, if necessary, before restarting.
Never make any adjustments or repairs with • the engine running.
Check grass catcher components and the • discharge guard frequently and replace with manufacturer’s recommended parts, when necessary.
Mower blades are sharp. Wrap the blade or • wear gloves, and use extra caution when servicing them.
Check brake operation frequently. Adjust and • service as required.
Maintain or replace safety and instruction • labels, as necessary.
Do not modify safety equipment. Check • regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices.
Do not change the settings of governors and • avoid running the engine with overly high engine speeds. If you run the engine too fast, you risk damaging the machine components.
Be very careful when handling battery acid. • Acid on skin can cause serious corrosive burns. If you spill battery acid on your skin, rinse immediately with water.
Acid in the eyes can cause blindness, contact a • doctor immediately.
Be careful when servicing the battery. • Explosive gases form in the battery. Never perform maintenance on the battery when
smoking or near open ames or sparks.
The battery can explode and cause serious • injury/damage.
SAFETY
8011-515
Never drive the machine in an enclosed space
Use protective glasses for maintenance work. refueling.
WARNING! The battery contains lead and lead
compounds, chemicals that are considered to cause cancer, birth defects, and other reproductive system damage. Wash your hands after handling the battery.
English-14
SAFETY
Ensure that nuts and bolts, especially the • fastening bolts for the blade attachments, are properly tightened, torqued and that the equipment is in good condition.
Do not modify safety equipment. Check • regularly to be sure it works properly. The machine must not be driven with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices.
Do not change the settings of governors and • avoid running the engine with overly high engine speeds. If you run the engine too fast, you risk damaging the machine components.
Sparking can occur when working with the • battery and the heavy cables of the starter
circuit. This can cause battery explosion, re or
eye injury. Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery.
6003-009
6003-009
Do not smoke when performing maintenance on the battery. The battery can explode and cause serious injury/damage.
WARNING! Avoid electrical sparking and its
consequences by the following routines:
Use protective goggles.• Ensure that the fuel ller cap is mounted tightly •
and no ammable substances is stored in an
open vessel. Never work with the starter circuit if there is •
spilled fuel. Disconnect the chassis cable from the battery •
rst and reconnect it last.
Do not make a bridge short circuit across the • starter relay to run the starter.
Never use the machine indoors or in spaces • lacking proper ventilation. The exhaust fumes contain carbon monoxide, an odorless, poisonous, and lethal gas.
Stop and inspect the equipment if you run over • or into anything. If necessary, make repairs before starting.
Never make adjustments with the engine • running.
The machine is tested and approved only • with the equipment originally provided or recommended by the manufacturer. Only use approved repair parts for the machine.
8009-728
Risk of sparking
English-15
The blades are sharp and can cause cuts and • gashes. Wrap the blades or use protective gloves when handling them.
Check the parking brake’s functionality • regularly. Adjust and service as necessary.
The mulch blades should only be used in • familiar areas when higher quality mowing is desired.
Reduce the risk of re by removing grass, •
leaves, and other debris that may have accumulated on the machine. Allow the machine to cool before putting it in storage.
Regularly clean deck and underside of • deck, avoid spraying engine and electrical components with water.

Transport

The machine is heavy and can cause serious • crushing injuries. Be extra cautious when it is loaded on or unloaded from a vehicle or trailer.
Use an approved trailer to transport the • machine. Activate the parking brake, turn off the fuel supply, and fasten the machine with approved fastening devices, such as bands, chains, or straps, when transporting.
Do not operate this machine on public • roadways.
Check and abide by local trafc regulations •
before transporting the machine on any road. Do not tow this machine, it may cause damage •
to the drive system. Do not tow any trailers, etc. with this mower. •
They may jackknife or overturn causing damage to the mower and possibly serious injury to the operator.
SAFETY
8011-515
Clean the machine regularly
WARNING! Escaping hydraulic oil under pressure can
have sufcient force to penetrate the skin,
causing serious injury. If injured by escaping
uid, see a doctor at once. Serious infection
or reaction can develop if proper medical treatment is not administered immediately.
IMPORTANT INFORMATION
The parking brake is not sufcient to lock the
machine in place during transport. Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the transport vehicle to avoid tipping it over.
English-16
SAFETY

Roll over Protection system (ROPS)

The ROPS increases the basic weight of the unit by 42 lbs/19 kg. The ROPS on the US units are standard, on the European units is the ROPS an accessory.
Do not use ROPS as a lifting, attaching or • anchoring point.
Do not use ROPS for wrecking or towing.• Do not exceed Max GVW: 2822 lbs/1283 kg.• Read machine operator’s manual before each •
use. Securely fasten your seat belt if the unit has a •
ROPS. Where possible, avoid operating the unit near •
ditches, embankments and holes. Reduce speed when turning, crossing slopes •
and on rough, slick or muddy surfaces. Stay off slopes too steep for safe operation.• Watch where you are going, especially at row •
ends, on roads and around trees. Do not permit others to ride.• Operate the mower smoothly - no jerky turns, •
starts or stops. When mower is stopped, set brakes securely •
and use park brake. If any part of ROPS is damaged, the entire •
ROPS must be replaced. Check all bolts including seat belt for correct •
torque before each use. Check ROPS structure for damage before •
each use. ROPS bar is NOT intended for use in sub zero •
temperatures.
WARNING! The structures capability may be impaired by
structural damage if overturned, or alteration occurs. If any of these conditions take place, the total structure MUST be replaced.
WARNING! This mower is equipped with an internal
combustion engine and should not be used on or near any unimproved forest-covered, bush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

Customer responsibilities

Read and observe the safety rules.• Follow a regular schedule in maintaining, •
caring for and using your mower. Follow the instructions under “Maintenance” •
and “Storage” sections of this owner’s manual.
A spark arrester for the mufer is available through
your authorized Yazoo/Kees dealer.
English-17

Setup

Uncrate machine.

SETUP AND ADJUSTMENTS

ROPS Assembly Components

1 - Top loop 1 - Left side post 1 - Right side post 1 - Hardware bag 2 - Latch Pins w/lanyard 6 - Cap screws 6 - Centerlock nuts 2 - Knobs (all hardware Grade 5).
1. Remove roll bar and parts bag from the box.
2. Install roll bar side posts. a. Locate the LEFT and RIGHT side posts.
b. Slide the left side post into the left side
receiver on the frame, do the same on the right side.
c. Using the cap screws, two per post, align
the holes in the side post with the frame
receiver. Install the centerlock nuts nger
tight to the side post bolts.
3. Install roll bar top loop. a. Align the holes of the top loop with the left
and right side posts.
b. Slide the latch pins through the front hole
on the left and right side to connect the top loop to the side posts and secure with the hairpin.
c. Insert cap screws through the rear hole on
the left and right side. Install the centerlock
nuts nger tight.
4. Torque all hardware to 80 ft./lbs. (110 N•m).
5. Install and tighten knobs against the side post.
6. If ROPS has been installed correctly, the unit should fold to the rear of the machine when not in use.
WARNING! No settings or adjustments are to be made
unless: Engine is stopped, key has been removed, park brake is on and battery cable removed from battery.
TOP LOOP
LATCH PIN
KNOB
½" CAPSCREW
½" CENTERLOCK NUT
RIGHT SIDE POST
LEFT SIDE POST
½" CENTERLOCK NUTS
English-18
½" CAPSCREWS
SETUP AND ADJUSTMENTS

Tires

Mount rear drive wheels using the lug nuts installed on the hubs.
Check the tire pressure in all four tires. All tires should be 15 psi.

Control Arms

Remove top bolt in control arm and loosen bottom bolt, rotate the control levers to the upright position. Align the levers so they are even in the neutral position. Reinstall hardware and tighten.

Seat Install

1. Remove seat assembly from the crate.
2. Remove the four nuts from the bottom of the seat. Retain for use later.
3. Align the seat bottom with the holes in the seat frame. Place seat on top of the seat frame and secure with the four nuts or knobs removed in Step 2.
4. Connect the wire harness from the seat to the frame harness.
Motion Control Lever
Control Arm

Engine Oil

Check engine oil with dip stick. Add if needed per
the engine manufactures specications. See engine manual for oil type and lling specications.
Operating
Range
“F” Full Mark
English-19
SETUP AND ADJUSTMENTS

Cutting Height

1. Stop the mower and disengage the blades.
2. Raise the deck height lever to the transport position.
3. Remove the height adjustment pin and place it in the desired cutting height hole. Lower the lift lever down onto pin.
NOTE: Anti-scalp rollers must be in the proper
position for maximum deck otation.
See the decal on the front deck for proper settings.

Mower Deck Leveling

1. Position machine on a at surface. Preferably
level concrete.
2. Check the tire pressure in all four tires. Ination
should be 15 psi.
3. Place 2x4s on edge under the cutting deck from front to rear and lower the deck down onto 2x4s.
4. Adjust the four upper chain bolts to the center slots in the deck lift arms.
NOTE: Make sure the lift blocks under the
frame are tightly bolted to the frame.
5. Check the chains for equal tension. If unequal adjust upper chain bolt in slot.
6. Place the deck in the 5" cutting height and measure from the cutting edge of the blade to
the at level surface to check the deck cutting
height.
Lift Lever
Deck Height Adjustment Plates

Throttle Lever Tension

Stop engine and remove key. Throttle lever tension may be adjusted by tightening
the pivot bolt. The pivot bolt secures the throttle arm to the mounting bracket which is mounted to the console. Access is gained by removing the console.
English-20
SETUP AND ADJUSTMENTS

Motion Control Linkage Adjustment

Adjustment must be made with the rear wheels rotating. Raise the rear of the machine and block it up so the wheels are free to rotate.
Tilt seat forward and remove the seat rod so 1.
the seat rotates forward onto the frame.
Place a 2x4 board between the foot plate 2.
and the center of the seat to engage the seat safety switch.
Loosen the nuts directly behind each ball 3.
joint on both rods that connect the pump arm to the motion control assemblies.
Start the engine. The park brake must be 4.
engaged and the motion control levers in the neutral slots to start the engine. Run the engine approximately half throttle.
Release park brake to allow the wheels to 5.
rotate.
Begin with either side and put the motion 6.
control lever into the neutral position.
Adjust the motion control linkage by rotating 7.
the double nuts in the proper direction until the wheel stops rotating.
Move the motion control lever forward and 8.
into the neutral position and into the neutral slot. The wheel must be stopped completely at this point.
Do the same in reverse and release the 9.
lever. The lever should return to neutral on its own.
Run engine full throttle to make sure wheels 10.
do not rotate. Readjust if any rotation occurs.
Repeat the whole process for the opposite 11.
side and tighten the nuts against the ball
joints. Turn machine off.12. Reinstall the seat rod and check the wiring 13.
harness to the seat safety switch for a good
connection and return the seat to the normal
position.
CAUTION! Keep hands, feet and clothing away from
rotating tires.
Motion Control Lever
Turn Here To Adjust
Loosen Here (Left Hand Thread)
Loosen Here
Pump Arm

Park Brake Adjustment

See your authorized Yazoo/Kees dealer for any park brake adjustment.
English-21
Loading...
+ 47 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use