Yamaha Audio PSR-225 User Manual

SPECIAL MESSAGE SECTION (U.S.A.)

This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha.
This product should be used only with the compo­nents supplied or; a cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please observe all safety markings and instruc­tions that accompany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is be­lieved to be correct at the time of printing. How­ever, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units.
This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for long periods of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. IMPORTANT: The louder the sound, the shorter the time period before damage occurs.
NOTICE:
Service charges incurred due to lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and environmentally friendly. We sin­cerely believe that our products and the produc­tion methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the follow­ing:
Battery Notice:
This product MAY contain a small non-recharge­able battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement.
This product may also use “household” type bat­teries. Some of these may be rechargeable. Make sure that the battery being charged is a recharge­able type and that the charger is intended for the battery being charged.
When installing batteries, do not mix old batteries with new, or with batteries of a different type. Batteries MUST be installed correctly. Mismatches or incorrect installation may result in overheating and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regu­lated by the laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some reason its useful life is consid­ered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate. You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase.
Model Serial No. Purchase Date
92-BP
PLEASE KEEP THIS MANUAL
2

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep these precautions in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
• Do not open the instrument or attempt to disassemble the internal parts or modify them in any way. The instrument contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immedi­ately and have it inspected by qualified Yamaha service personnel.
• Do not expose the instrument to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings.
• If the AC adaptor cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the instrument, or if any unusual smells or smoke should appear to be caused by it, immediately turn off
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following:
the power switch, disconnect the adaptor plug from the outlet, and have the instrument inspected by qualified Yamaha service personnel.
• Use the specified adaptor (PA-3B or an equivalent recommended by Yamaha) only. Using the wrong adaptor can result in damage to the in­strument or overheating.
• Before cleaning the instrument, always remove the electric plug from the outlet. Never insert or remove an electric plug with wet hands.
• Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.
• Do not place the AC adaptor cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.
• When removing the electric plug from the instrument or an outlet, always hold the plug itself and not the cord.
• Do not connect the instrument to an electrical outlet using a multiple­connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet.
• Unplug the AC power adaptor when not using the instrument, or during electrical storms.
• Always make sure all batteries are inserted in conformity with the +/­polarity markings. Failure to do so might result in overheating, fire, or battery fluid leakage.
• Always replace all batteries at the same time. Do not use new batteries together with old ones. Also, do not mix battery types, such as alkaline batteries with manganese batteries, or batteries from different makers, or different types of batteries from the same maker, since this can cause overheating, fire, or battery fluid leakage.
• Do not dispose of batteries in fire.
• Do not attempt to recharge batteries that are not intended to be charged.
• If the instrument is not to be in use for a long time, remove the batteries from it, in order to prevent possible fluid leakage from the battery.
• Keep batteries away from children.
• Before connecting the instrument to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum.
• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components.
• Do not use the instrument near other electrical products such as televi­sions, radios, or speakers, since this might cause interference which can affect proper operation of the other products.
• Do not place the instrument in an unstable position where it might acci­dentally fall over.
• Before moving the instrument, remove all connected adaptor and other cables.
• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths. Also, do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.
• Do not rest your weight on, or place heavy objects on the instrument, and do not use excessive force on the buttons, switches or connectors.
• Use only the stand/rack specified for the instrument. When attaching the stand or rack, use the provided screws only. Failure to do so could cause damage to the internal components or result in the instrument falling over.
• Do not operate the instrument for a long period of time at a high or uncom­fortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.
SAVING USER DATA
• Save all data to an external device such as the Yamaha MIDI Data Filer MDF3, in order to help prevent the loss of important data due to a mal­function or user operating error.
Yamaha cannot be held responsible for damage caused by improper use or modi­fications to the instrument, or data that is lost or destroyed.
Always turn the power off when the instrument is not in use.
Make sure to discard used batteries according to local regulations.
* The illustrations and LCD screens as shown in this owner’s manual are for in-
structional purposes only, and may be different from the ones on your instru­ment.
(4)-2
3
Congratulations on your purchase of the Yamaha
PSR-225 PortaTone!
You now own a portable keyboard that combines advanced func-
tions, great sound and exceptional ease-of-use in a highly compact
package. Its outstanding features also make it a remarkably ex-
pressive and versatile instrument.
Read this Owner’s Manual carefully while playing your new
PortaTone in order to take full advantage of its various features.

Main Features

The PSR-225 is a sophisticated yet easy-to-use keyboard with the following features and functions:
Yamaha Education Suite
................................................ Pages 60-71
The PortaTone features the new Yamaha Education Suite — a set of learning tools that utilize the latest technology to make studying and practicing music more fun and fulfilling than ever before!
The Yamaha Education Suite includes:
Chord Guide functions in the Style mode — Smart and Dictionary — that make it exceptionally easy to learn chords and chord relationships. There’s also a powerful EZ Chord function that lets you easily record and play back chord progressions.
• Smart lets you easily play harmonically “correct” chord progressions for whatever key you specify. It’s great for learning — and performing!
• Dictionary is a built-in “chord encyclopedia” that teaches you how to play specific chords. You type in the chord name, and the PortaTone shows you which notes to play!
• EZ Chord is a powerful and simple way to pro­gram and play chord progressions. Record all the chord changes you need for a song, then play back the chords one after another by simply playing a single key!
Portable Grand............................Page 24
The PortaTone also has a Portable Grand function for realistic piano performance. Pressing the PORTABLE GRAND button instantly calls up the stunningly authentic “Stereo Sampling Piano” voice and configures the entire PortaTone for optimum piano play. Special Pianist styles — with piano-only accompaniment — are also provided.
Other powerful features include:
• Exceptionally realistic and dynamic sounds with 100
voices, utilizing digital recordings of actual instruments.
• Dual voice and Split voice modes that let you layer two
voices together or assign two voices to separate sections of the keyboard
• Four high-quality effects — Reverb, Chorus, DSP, and
Harmony — each with a variety of different types.
• 100 auto accompaniment styles, each with different
Intro, Main A and B, and Ending sections. All styles (except for the Pianist styles) also have their own four Fill­in patterns. The PortaTone also gives you convenient control over accompaniment Styles — including Tempo and independent Accompaniment Volume.
• Powerful song recording operations for recording and
playing back complete compositions (three User songs are available). Up to six tracks can be recorded to a song, including a special chord track for style accompaniment.
• One Touch Setting (OTS), for automatically calling up an
appropriate voice for playing with the selected style. Plus, there are 16 User OTS memory spaces that let you save your custom panel settings for instant recall.
• Touch response (with front panel on/off switch) for
maximum expressive level control over the voices. This also works in conjunction with the Dynamic Filter, which dynamically adjusts the timbre or tone of a voice accord­ing to your playing strength — just a like a real musical instrument!
• Convenient footswitch control over various functions —
including sustain, start/stop, and more.
• GM (General MIDI) compatibility and full GM voice set.
• Large custom LCD gives you easy, at-a-glance confirma-
tion of all important settings, as well as chord and note indications.
• Comprehensive MIDI functions that let you integrate the
PortaTone into a MIDI music system, for sequence record­ing and other advanced applications.
• Built-in, high-quality stereo amplifier/speaker system.
4
4

Contents

PANEL CONTROLS AND TERMINALS 6
• Front Panel ............................... 6
• Rear Panel ................................ 7
SETTING UP 8
POWER REQUIREMENTS ................. 8
TURNING ON THE POWER ............. 8
ACCESSORY JACKS ......................... 9
Quick Guide — How to Use Your New PSR-225 PortaTone 10
Step 1 Voices ............................. 10
Step 2 Auto Accompaniment .... 12
Step 3 Chord Guide .................. 14
Step 4 Songs ............................. 16
Step 5 Function Parameters ...... 18
Step 6 MIDI ............................... 20
PANEL DISPLAY INDICATIONS
• Music Stand ........................... 23
22
PORTABLE GRAND 24
PLAYING THE PORTABLE GRAND .. 24
USING THE METRONOME .............. 24
• Setting the Metronome
Time Signature ....................... 25
• Adjusting the Metronome
Volume ................................... 26
PLAYING VOICES — THE VOICE MODE 27
PLAYING A VOICE — MAIN VOICE 27
• About Panel Voices and
GM Voices .............................. 29
• Drum Kit Voice Chart
(voices 101 - 110) .................. 30
Function Parameters — Main Voice
TRANSPOSE AND TUNING ............. 32
Transpose .................................... 32
Tuning ......................................... 33
PLAYING TWO VOICES —
DUAL VOICE ................................... 34
Function Parameters — Dual Voice
PLAYING TWO VOICES —
SPLIT VOICE .................................... 36
Function Parameters — Split Voice 37
ADDITIONAL VOICE FUNCTIONS — VOICE SET AND
TOUCH SENSITIVITY ...................... 38
Function Parameters —
Voice Set and Touch Sensitivity ..... 39
30
35
EFFECTS 40
REVERB ............................................ 40
CHORUS .......................................... 41
DSP ................................................. 42
HARMONY ...................................... 43
Function Parameters — Effects ...... 44
• Effect Types ............................ 45
AUTO ACCOMPANIMENT — THE STYLE MODE 47
SELECTING A STYLE AND PLAYING THE ACCOMPANIMENT .. 47
ACCOMPANIMENT CONTROLS ..... 52
USING THE AUTO
ACCOMPANIMENT FEATURES ........ 52
CHANGING THE TEMPO ................ 53
ACCOMPANIMENT SECTIONS (MAIN A, MAIN B AND FILL-INS) ... 54
ADJUSTING THE
ACCOMPANIMENT VOLUME ......... 55
USING AUTO ACCOMPANIMENT —
MULTI FINGERING .......................... 56
Single Finger Chords .................. 56
Fingered Chords ......................... 56
SETTING THE ACCOMPANIMENT
SPLIT POINT ................................... 58
Function Parameter —
Accompaniment Split Point .......... 59
WHAT IS A CHORD? ....................... 60
WRITING CHORD NAMES .............. 61
The Intervals of the Scale ........... 61
Other Chords .............................. 61
CHORD GUIDE ................................ 62
Dictionary ................................... 62
Smart ........................................... 64
• Smart Chord List .................... 65
EZ Chord ..................................... 66
EZ Chord — Playback ................... 66
• Bank Chain ............................. 67
EZ Chord — Recording .................68
• Recording a Space.................. 69
• Playing the Accompaniment During EZ Chord Recording ... 69
• HINT — Using Spaces............. 70
Clearing an EZ Chord Bank ........... 71
ONE TOUCH SETTING (OTS) 72
ONE TOUCH SETTING — USER ...... 72
Recording a User One Touch
Setting ......................................... 72
Recalling a User One Touch Setting
• Selecting a User Bank ............. 73
ONE TOUCH SETTING — PRESET ... 74
Selecting a Preset One Touch
Setting ......................................... 74
73
SELECTING AND PLAYING SONGS — THE SONG MODE 75
SELECTING AND PLAYING A SONG
CHANGING THE TEMPO ................ 76
ABOUT THE BEAT DISPLAY ............. 77
ADJUSTING THE SONG VOLUME ... 78
75
SONG RECORDING 79
RECORDING A USER SONG —
REALTIME RECORDING .................. 80
• Using the Metronome ............ 81
• Additional Operations ............ 83
RECORDING A USER SONG —
STEP RECORDING ........................... 84
Recording Notes ........................... 85
• Additional Operations ............ 87
Replacing a Note or Rest .............. 88
Entering Velocity Curves ............... 89
• Velocity Curve Chart............... 89
CLEARING A SONG ......................... 90
FOOTSWITCH 91
• Footswitch Assign Functions ... 92
MIDI FUNCTIONS 93
WHAT IS MIDI? ............................... 93
Channel Messages ........................ 94
System Messages .......................... 94
• MIDI Terminals ....................... 94
CONNECTING TO A PERSONAL
COMPUTER ..................................... 95
FUNCTION PARAMETERS — MIDI .. 96
USING BULK DUMP SEND
TO SAVE DATA ................................ 99
Saving Bulk Data .......................... 99
Loading Bulk Data ...................... 101
USING INITIAL SETUP SEND
WITH A SEQUENCER .................... 102
Sending Initial Setup Data .......... 102
TROUBLESHOOTING .................... 104
DATA BACKUP & INITIALIZATION 105
INDEX ........................................... 106
SONG SCORES
(EZ Chord banks 1, 2) ................... 107
VOICE LIST .................................... 108
STYLE LIST .................................... 111
DRUM KIT LIST ............................. 112
MIDI IMPLEMENTATION CHART .. 114
SPECIFICATIONS ........................... 117
5

PANEL CONTROLS AND TERMINALS

Front Panel

STYLE
FUNCTION
MIN MAX
MASTER VOLUME
CHORD TYPE
54 56 58 59
57
L
VOICE
TEMPO
STYLE
TRANSPOSE
TUNING
ACMP/SONG
VOLUME
METRONOME
MEASURE TEMPO
VOLUME
001 116
OVERALL
B
DEMO START
A
J K L M N
START/
SYNC-
ACMP
ON/OFF
(9)
M
M
M
C
60
61
L
H
1
START
6 mM7 M7
R
62
63
H
1
STOP
PIANIST
51 ~ 55 56 ~ 60 61 ~ 66 67 ~ 70 71 ~ 72 73 ~ 80 81 ~ 88 89 ~ 90
96 97 98 99
100
5 6 7 8
1 1 ~ 3 1 ~ 3 1 ~ 7
1 ~ 10 11 ~ 17 18 ~ 20 21 ~ 27 28 ~ 30 31 ~ 36 37 ~ 40 41 ~ 46 47 ~ 50
91 92 93 94 95
0 1 2 3 4
1 ~ 6 1 ~ 8 1 ~ 9 1 ~ 9 1
8BEAT 16BEAT 6/8 BALLAD DANCE DISCO ROCK ROCK & ROLL RHYTHM & BLUES CONTEMPORARY JAZZ
ROCK-A-BALLAD 8BEAT SWING JAZZ BALLAD 2BEAT
MAIN VOICE DUAL VOICE SPLIT VOICE EFFECT ONE TOUCH SETTING
PSR-225
49 55 70 71 74 8147248
50
46 51 53
3
52
2
3
TRADITIONAL JAZZ AMERICAS COUNTRY & WESTERN BALLROOM LATIN BALLROOM STANDARD MARCH & WALTZ LATIN CARIBBEAN
BOOGIE RAGTIME ARPEGGIO WALTZ HAPPY
STYLE SONG UTILITY MIDI
L H
A MASTER VOLUME dial
This determines the overall volume of the PortaTone.
B OVERALL, DEMO START buttons (
▲, ▼
, +, -)
These are for selecting the various “overall” functions and setting their values. (See pages 22, 24.) They are also used to play the Demo songs. (See page 16.)
C FUNCTION button
This selects the Function mode. (See page 18.)
GrandPno
001
FUNCTION SONG STYLE VOICE
D
C
MAIN A
INTRO/ ENDING rit.
m m(9)
64 65R66
AUTO FILL
(9)
m7
67
S
H PORTABLE GRAND button
This instantly changes to the Voice mode and calls up the Grand Piano voice. (See page 24.)
I METRONOME button
This turns the metronome on and off. (See page
24.)
VOICE
PANEL VOICE
1 ~ 12
13 ~ 19
I
20 ~ 32 33 ~ 41 42 ~ 49
METRONOME
50 ~ 60
61 ~ 65 GM VOICE 111~118 119~126 127~134 135~142 143~150
9
151~158
3
159~166 167~174
FWD
YES
ONE TOUCH SETTING
SONG MEMORY
( 11)
( 13)
7(13)7
7
75H76L77H78L79
Q
dim7 dim
PIANO MALLET ORGAN GUITAR BASS ENSEMBLE STRINGS
PIANO CHROMATIC ORGAN GUITAR BASS STRINGS ENSEMBLE BRASS
66 ~ 75 76 ~ 84 85 ~ 89 90 ~ 95 96 ~ 100
101 ~ 110
175~182 183~190 191~198 199~206 207~214 215~222 223~230 231~238
HARMONY
PRESETUSER
B
T
aug
7aug
7sus4 C
80 85 86
H L
82 83H84
R S
DUAL
sus4 C /D D /ED
ROOT
123
4 56
7 8
BWD
NO
F
E
O P
CHORD GUIDE
MAIN B
m7 m7 5m67
C
69
68 73
2
DICTIONARY SMART EZ OFF
R 2
RECORD
(
)
7
9
72
H
PORTABLE GRAND
H
G
rest
0
velocity
1234A
1 2 3 4 5 6/CHORD
( 9)7(9)
7
L
• Setting the time signature for the Metro­nome (page 25)
• Setting the key signature for the Smart Chord function (page 64)
BRASS REED PIPE SYNTH LEAD SYNTH PAD DRUM KITS
REED PIPE SYNTH LEAD SYNTH PAD SYNTH EFFECTS ETHNIC PERCUSSIVE SOUND EFFECTS
REVERB
TOUCH
L
STAND BY ON
D SONG button
This selects the Song mode. (See pages 16, 75.)
E STYLE button
This selects the Style mode. (See pages 12, 47.)
F VOICE button
This selects the Voice mode. (See pages 10, 27.)
G Numeric keypad, +/- buttons
These are for selecting songs, voices, and styles. (See pages 28, 47, and 76.) They are also used for making various settings, such as:
• Selecting and changing the Function parameters (page 18)
• Setting note values and other settings for the Step Record function (page 85)
6
J ACMP ON/OFF button
When the Style mode is selected, this turns the auto accompaniment on and off. (See page 52.) This button has no function in the Song Play mode.
K SYNC-START button
This turns the Sync-Start function on and off. (See page 48.)
L START/STOP button
When the Style mode is selected, this alternately starts and stops the auto accompaniment. (See page 48.) In the Song mode, this alternately starts and stops song playback. (See page 76.)
PANEL CONTROLS AND TERM INALS
M INTRO/ENDING button
When the Style mode is selected, this is used to control the Intro and Ending functions. (See pages 49, 51.)
N MAIN A/B (AUTO FILL) buttons
When the Style mode is selected, these are used to change auto accompaniment sections and control the Auto Fill function. (See page 54.)
O CHORD GUIDE button
When the Style mode is selected, this is used to control the Chord Guide functions. (See page
62.)
P RECORD button
This is used for selecting and enabling the recording functions: Song (pages 80, 84), EZ Chord (page 68), and One Touch Setting (page
72).
Q ONE TOUCH SETTING / SONG MEMORY
buttons
When the Style mode is selected, these are used
to select the One Touch Setting registrations (page 73). When the Song mode is selected, these are used to select specific tracks (pages 81,
85).
R HARMONY button
This turns the Harmony effect on and off. (See page 43.)
S REVERB button
This turns the Reverb effect on and off. (See page 40.)
T DUAL button
This turns the Dual mode on and off. (See page
34.)
TOUCH button
This turns the Touch function on and off. (See page 38.)
Power switch (STAND BY/ON)

Rear Panel

A B
PHONES/
DC IN 10-12V
AUX OUT
A DC IN 10-12V jack
This is for connection to a PA-3B AC power adaptor. (See page 8.)
B PHONES/AUX OUT jack
This is for connection to a set of stereo head­phones or to an external amplifier/speaker system. (See page 9.)
C
FOOT SWITCH
D
MIDI
IN OUT
C FOOT SWITCH jack
This is for connection to an optional FC4 or FC5 Footswitch. The footswitch is generally used to control sustain, but it can conveniently be set to control one of a variety of functions instead. (See pages 9, 91.)
D MIDI IN, OUT terminals
These are for connection to other MIDI instru­ments and devices. (See page 94.)
7

SETTING UP

STAND BY ON
This section contains information about setting up your PortaTone for playing. Make sure to read this section carefully before using the instrument.

POWER REQUIREMENTS

Although the PSR-225 will run either from an optional AC adaptor or batteries, Yamaha rec­ommends use of an AC adaptor whenever possible. An AC adaptor is more environmen­tally friendly than batteries and does not deplete resources.
Never interrupt the power supply (e.g. remove the batteries or unplug the AC adaptor) during any PSR-225 record operation! Doing so can result in a loss of data.
Using an AC Power Adaptor
To connect your PortaTone to a wall socket, you will need the optionally available Yamaha PA-3B Power Adaptor. Use of other AC adaptors could result in damage to the instrument, so be sure to ask for the right kind. Connect one end of the adaptor to the DC IN 10-12V jack on the rear panel of your PortaTone, and the other end to a suitable electrical outlet.
• Use ONLY a Yamaha PA-3B AC Power Adaptor (or other adaptor specifically recommended by Yamaha) to power your instrument from the AC mains. The use of other adaptors may result in irreparable damage to both the adaptor and the PSR-
225.
• Unplug the AC Power Adaptor when not using the PSR-225, or during electrical storms.
BATTERIES 1.5V x 6
When the Batteries Run Down
When the batteries run low and the battery voltage drops below a certain level, the PortaTone may not sound or function properly. As soon as this happens, replace them with a complete set of six new batteries.
• Never mix old and new batteries or different types of batteries (e.g., alkaline and manganese).
• To prevent possible damage from battery leakage, remove the batteries from the instrument if it is not to be used for a long time.

TURNING ON THE POWER

With the AC power adaptor connected or with batteries installed, simply press the power switch until it locks in the ON position. When the instrument is not in use, be sure to turn the power off. (Press the switch again so that it pops up.)
Using Batteries
Inserting Batteries
Turn the instrument upside-down and remove the battery compartment lid. Insert six 1.5-volt size “D” (SUM-1, R-20 or equivalent) batteries as shown in the illustration, making sure that the positive and negative terminals are properly aligned, and replace the lid.
8
Even when the switch is in the “STAND BY” position, electricity is still flowing to the instrument at the minimum level. When you are not using the PSR-225 for a long time, make sure you unplug the AC power adaptor from the wall AC outlet, and/or remove the batteries from the instrument.
SETTING UP

ACCESSORY JACKS

Using Headphones
For private practicing and playing without disturbing others, connect a set of stereo head­phones to the rear panel PHONES/AUX OUT jack. Sound from the built-in speaker system is automatically cut off when you insert a head­phone plug into this jack.
PHONES/ AUX OUT
Connecting a Keyboard Amplifier or Stereo
System
Though the PortaTone is equipped with a built­in speaker system, you can also play it through an external amplifier/speaker system. First, make sure the PortaTone and any external devices are turned off, then connect one end of a stereo audio cable to the LINE IN or AUX IN jack(s) of the other device and the other end to the rear panel PHONES/AUX OUT jack on the PortaTone.
Using a Footswitch
This feature lets you use an optional footswitch (Yamaha FC4 or FC5) to sustain the sound of the voices, or control a variety of other functions. (See page 91.) When this is used for sustain, the footswitch functions the same way as a damper pedal on an acoustic piano — press and hold down the footswitch as you play the keyboard to sustain the sound.
FOOT SWITCH
• Make sure that the footswitch plug is properly connected to the FOOT SWITCH jack before turning on the power.
• Do not press the footswitch while turning the power on. Doing this changes the recognized polarity of the footswitch, resulting in reversed footswitch operation.
Using the MIDI Terminals
The PortaTone also features MIDI termi-
MIDI instrument
nals, allowing you to interface the PortaTone with other MIDI instruments and devices. (For more information, see
MIDI
pages 20, 93.)
IN OUT
PHONES/ AUX OUT
To prevent damage to the speakers, set the volume of the external devices at the minimum setting before connecting them. Failure to observe these cautions may result in electric shock or equipment damage.
Stereo system
9
001
001 063
MEASURE TEMPO
GrandPno
VOICE STYLE
Quick Guide — How to
Quick Guide — How to
Use Your New PSR-225
Use Your New PSR-225

CCCCCDDDDDDEEEEE

ГГГГГДДДДДДЕЕЕЕЕ
PortaTone
PortaTone

Step 1 Voices

This brief, easy-to-follow section shows you how to use the basic features and functions of your new PSR-225 PortaTone. If you’ve never touched an electronic keyboard before, reading and going through the steps in this section will make you familiar with the PortaTone in a very short time. It will also give you the tools you need to explore the advanced capabilities of the instrument and use them effectively in your own music. Good luck...and enjoy!
PORTABLE GRAND
VOICE
TEMPO
1 2
MIN MAX
MASTER VOLUME
METRONOME
OVERALL
TRANSPOSE
TUNING
ACMP/SONG
VOLUME VOLUME
ACMP
ON/OFF
STYLE
MEASURE TEMPO
DEMO START
SYNC­START
GrandPno
001
001 063
FUNCTION SONG STYLE VOICE
MAIN A
INTRO/
START/
ENDING rit.
STOP
AUTO FILL
MAIN B
CHORD GUIDE
DICTIONARY SMART EZ OFF
123
4 56
7 8
BWD
NO
RECORD
METRONOME
9
rest
3
0
velocity
FWD
YES
1234A
1 2 3 4 5 6/CHORD
z q
q
ONE TOUCH SETTING
SONG MEMORY
Playing the Piano Voice
Portable Grand
z Press the PORTABLE GRAND
button.
PORTABLE GRAND
METRONOME
The Grand Piano voice is automatically selected.
x Play the keyboard.
Want to find out more? See page 24.
DUAL
TOUCH
REVERB
STAND BY ON
HARMONY
PRESETUSER
B
10
zx
Selecting other voices
The PSR-225 features a total of 238 high-quality voices. Let’s try a few of them out...
Panel voices ........... 1 - 100 (100 voices)
101 - 110 (10 drum kit voices)
GM voices .............. 111 - 238 (128 voices)
z Enter the Voice mode.
FUNCTION SONG STYLE VOICE
x Select a voice.
VOICE STYLE
BritePno
002
123
4 56
7 8
rest
0
velocity
BWD
NO
9
3
FWD
YES
c Play the keyboard.
Want to find out more? See page 27.
Step1
PORTABLE GRAND
METRONOME
100
001 063
TEMPO
MtrVol
VOICE STYLE
METRONOME
VOLUME
MEASURE
DEMO START


CCCCCCDDDDD
EEEEE


ГГГГГГДДДДД
ЕЕЕЕЕ
Voices
Playing along with the Metronome
q Press the METRONOME button.
PORTABLE GRAND
Changing the Metronome Volume
1 Press one of the OVERALL
“MtrVol” is shown in the display.
▲/▼
buttons until
METRONOME
Want to find out more? See page 24.
Changing the time signature of the Metronome
q Simultaneously hold down the METRONOME button
and one of the number buttons (1 - 9) on the numeric keypad.
123
4 56
+
Normally, the Metronome is set to play in 4/4 time. To change this to 2/4, press number button “2.” To change it to 3/4 time, press number button “3.”
Want to find out more? See page 25.
7 8
BWD
NO
rest
0
velocity
9
3
FWD
YES
DEMO START
2 Press the OVERALL + or - button to raise or lower
the value.
Want to find out more? See page 26.
Panel Voice List
No. Voice Name
PIANO
001 Grand Piano 002 Bright Piano 003 Honky-tonk Piano 004 Funky Electric Piano 005 DX Electric Piano 006 MIDI Grand Piano 007 CP 80 008 Hyper Electric Piano 009 Bell Electric Piano 010 Harpsichord 011 Clavi 012 Celesta
MALLET
013 Vibraphone 014 Marimba 015 Xylophone 016 Tubular Bells 017 Timpani 018 Steel Drums 019 Music Box
ORGAN
020 Jazz Organ 1 021 Jazz Organ 2 022 Jazz Organ 3
No. Voice Name
023 Full Organ 024 Rock Organ 1 025 Rock Organ 2 026 16'+2' Organ 027 16'+4' Organ 028 Church Organ 029 Reed Organ 030 Musette Accordion 031 Traditional Accordion 032 Bandoneon
GUITAR
033 Classical Guitar 034 Folk Guitar 035 12Strings Guitar 036 Jazz Guitar 037 Octave Guitar 038 Clean Guitar 039 Muted Guitar 040 Overdriven Guitar 041 Distortion Guitar
BASS
042 Acoustic Bass 043 Finger Bass 044 Pick Bass 045 Fretless Bass
No. Voice Name
046 Slap Bass 047 Synth Bass 048 Techno Bass 049 Dance Bass
ENSEMBLE
050 Strings 051 Chamber Strings 052 Synth Strings 053 Slow Strings 054 Tremolo Strings 055 Pizzicato Strings 056 Choir 057 Choir Aahs 058 Choir Oohs 059 Synth Choir 060 Orchestra Hit
STRINGS
061 Violin 062 Cello 063 Contrabass 064 Banjo 065 Harp
BRASS
066 Trumpet 067 Muted Trumpet
No. Voice Name
068 Trombone 069 Trombone Section 070 French Horn 071 Tuba 072 Brass Section 073 Synth Brass 074 Jump Brass 075 Techno Brass
REED
076 Soprano Sax 077 Alto Sax 078 Tenor Sax 079 Baritone Sax 080 Oboe 081 English Horn 082 Bassoon 083 Clarinet 084 Harmonica
PIPE
085 Piccolo 086 Flute 087 Pan Flute 088 Recorder 089 Ocarina
No. Voice Name
SYNTH LEAD
090 Square Lead 091 Sawtooth Lead 092 Voice Lead 093 Crystal 094 Brightness 095 Analog Lead
SYNTH PAD
096 Fantasia 097 Bell Pad 098 Xenon Pad 099 Angels 100 Dark Moon
DRUM KITS
101 Standard Kit 1 102 Standard Kit 2 103 Room Kit 104 Rock Kit 105 Electronic Kit 106 Analog Kit 107 Dance Kit 108 Jazz Kit 109 Brush Kit 110 Symphony Kit
11

Step 2 Auto Accompaniment

AUTO FILL
MAIN A
INTRO/ ENDING rit.
MAIN B

CCCCCDDDDDDEEEEE

ГГГГГДДДДДДЕЕЕЕЕ
Using the auto accompaniment
The PSR-225 has powerful and easy-to-use auto accompaniment features. All you have to do is play chords with your left hand — and the PortaTone automatically produces appropriate bass, chord, and rhythm backing for your perfor­mance. Use your right hand to play melodies, and you’ll sound like an entire band!
z Enter the Style mode.
STYLE
MEASURE TEMPO
001 116
8BtPop1
001
x Select a style.
For a list of styles, see page 13.
STYLE
8BtPop2
002
123
4 56
7 8
rest
0
velocity
BWD
NO
9
3
FWD
YES
c Turn the auto accompaniment on.
Accompaniment
section
+
Left hand
Auto accompaniment
Right hand
Melody
(for example, bass + guitar + drums)
v Turn the Sync-Start function on.
MAIN A
ACMP
ON/OFF
SYNC- START
START/
STOP
INTRO/
ENDING rit.
AUTO FILL
MAIN B
b Play a chord with your left hand.
For help in learning how to play chords, refer to “Using the Chord Guide function” on page 14.
Accompaniment
section
n Select a section.
Try playing with the Intro, Main A/B, and Ending sections.
12
ACMP
ON/OFF
SYNC­START
MIN MAX
MASTER VOLUME
m Stop the auto accompa-
MAIN A
INTRO/
START/
ENDING rit.
STOP
VOICE
TEMPO
STYLE
TRANSPOSE
TUNING
ACMP/SONG
VOLUME
METRONOME
MEASURE TEMPO
VOLUME
OVERALL
DEMO START
SYNC-
ACMP
START
ON/OFF
cxz
vnm
MAIN B
AUTO FILL
GrandPno
001
001 116
FUNCTION SONG STYLE VOICE
MAIN A
INTRO/
START/
ENDING rit.
STOP
AUTO FILL
MAIN B
CHORD GUIDE
DICTIONARY SMART EZ OFF
niment.
PORTABLE GRAND
METRONOME
123
4 56
7 8
9
rest
3
0
velocity
BWD
NO
RECORD
FWD
YES
1234A
1 2 3 4 5 6/CHORD
START/
YNC-
STOP
TART
Want to find out more? See pages 47-61.
z x c
DUAL
TOUCH
REVERB
STAND BY ON
ONE TOUCH SETTING
SONG MEMORY
HARMONY
PRESETUSER
B
INTRO/ ENDING rit.
Step 2


CCCCCCDDDDD
EEEEE


ГГГГГГДДДДД
ЕЕЕЕЕ
Auto Accompaniment
Selecting a complete music style with ideal voice and other settings — One Touch Setting
The PortaTone features 100 different styles in various music genres. With the One Touch Setting function, you can call up voice and other settings that best match the selected style. Each style has been programmed with two Preset One Touch Settings.
z Enter the Style mode.
x Select a style.
For a list of styles, see below.
STYLE
Style List
No. Style Name
8BEAT
1 8Beat Pop 1 2 8Beat Pop 2 3 8Beat Uptempo 4 8Beat Standard 5 Folkrock 6 Pop Rock 7 8Beat Medium 8 8Beat Ballad 9 Epic Ballad 10 Piano Ballad
16BEAT
11 16Beat Shuffle 1 12 16Beat Shuffle 2 13 16Beat Pop 14 Funk 1 15 16Beat Ballad 1 16 16Beat Ballad 2 17 Soul Ballad
6/8 BALLAD
18 Slow Rock 1 19 Slow Rock 2 20 6/8 Ballad
8BtPop2
002
STYLE
MEASURE TEMPO
001 116
8BtPop1
001
BWD
NO
No. Style Name
DANCE
21 Dance Pop 1 22 Dance Pop 2 23 Techno 24 Eurobeat 25 Euro House 26 Hip Hop 27 Synth Boogie
DISCO
28 70s Disco 29 Disco Tropical 30 Polka Pop
ROCK
31 8Beat Rock Ballad 32 16Beat Rock Ballad 33 Hard Rock 34 Rock Shuffle 35 6/8 Heavy Rock 36 US Rock
ROCK & ROLL
37 Rock & Roll 1 38 Rock & Roll 2 39 Boogie 40 Twist
123
4 56
7 8
0
velocity
9
rest
3
FWD
YES
No. Style Name
RHYTHM & BLUES
41 R&B 42 Funk 2 43 Soul 44 Gospel Shuffle 45 6/8 Gospel 46 4/4 Blues
CONTEMPORARY JAZZ
47 Cool Jazz 48 Jazz Ballad 49 Jazz Waltz 50 Fusion
TRADITIONAL JAZZ
51 Swing 52 Big Band Swing 53 Big Band Ballad 54 Jazz Quartet 55 Dixieland
AMERICAS
56 Cajun 57 Banda 58 Mariachi 59 Tejano 60 Cumbia
c Press one of the One Touch Setting
buttons: Preset A or B.
1234A
ONE TOUCH SETTING
PRESETUSER
B
v Play the keyboard.
Want to find out more? See page 74.
No. Style Name
COUNTRY & WESTERN
61 Bluegrass 62 Country 2/4 63 Country Rock 64 Country Ballad 65 Country Shuffle 66 Country Waltz
BALLROOM LATIN
67 Cha Cha 68 Rhumba 69 Pasodoble 70 Tango Continental
BALLROOM STANDARD
71 Foxtrot 72 Jive
MARCH & WALTZ
73 March 1 74 March 2 75 6/8 March 76 Polka 77 Standard Waltz 78 German Waltz 79 Viennese Waltz 80 Musette Waltz
No. Style Name
81 Bossa Nova 1 82 Bossa Nova 2 83 Salsa 84 Samba 85 Mambo 86 Beguine 87 Merengue 88 Bolero Lento
CARIBBEAN
89 Reggae 12 90 Pop Reggae
91 Rock-A-Ballad 92 8Beat 93 Swing 94 Jazz Ballad 95 2Beat 96 Boogie 97 Ragtime 98 Arpeggio 99 Waltz 100 Happy
LATIN
PIANIST
13

Step 3 Chord Guide

001 116
MEASURE TEMPO
ACMP ON
M
7

CCCCCDDDDDDEEEEE

ГГГГГДДДДДДЕЕЕЕЕ
Using the Chord Guide function
Learning how to play specific chords
M7
Example:
GM
Root note Chord type
7
Here, you’ll learn how to use the Chord Guide functions to show the individual notes of chords.
z Enter the Style mode, then press the
CHORD GUIDE button until “Dict.” is
c Specify the chord type of the chord.
CHORD TYPE
shown in the display.
CHORD GUIDE
DICTIONARY SMART EZ OFF
STYLE
ACMP ON
MEASURE TEMPO
001 116
Dict.
v Play the notes of the chord as indicated
in the keyboard diagram in the display.
x Specify the root note of the chord.
ROOT
G
STYLE
ACMP ON
Dict.
Playing appropriate chords with just one finger
The PortaTone also lets you easily create appropriate chords for a given scale by simply playing single notes in the scale.
The notes in the keyboard diagram flash when the chord is played properly.
Want to find out more? See page 62.
z Enter the Style mode, then press the
CHORD GUIDE button until “Smart” is shown in the display.
CHORD GUIDE
DICTIONARY SMART EZ OFF
STYLE
ACMP ON
MEASURE TEMPO
001 116
Smart
x Set the key to match that of the song you
wish to play. Enter the number of sharps or flats of the corresponding key.
STYLE
14
15
b=1
c Start the auto accompaniment.
SYNC­START
STOP
ENDING rit.
INTRO/
START/
v Play single note chords (root note) on the
keyboard.
To play these
chords....
.....press these
keys (root notes)
F Dm Gm Dm
Want to find out more? See page 64.
Step 3


CCCCCCDDDDD
EEEEE


ГГГГГГДДДДД
ЕЕЕЕЕ
Chord Guide
Playing chord progressions (songs) with just one finger
The EZ Chord function gives you an exceptionally easy way to play the chords of a song. Simply press single keys in succession, and the PortaTone automatically plays the proper chords for you!
q Enter the Style mode, then press the
CHORD GUIDE button until “EZ. is shown in the display.
STYLE
ACMP ON
CHORD GUIDE
DICTIONARY SMART EZ OFF
001 116
w Select an EZ Chord bank.
STYLE
EZ
2
1
TEMPO
EZ
123
4 56
7 8
BWD
NO
rest
0
velocity
9
3
e Start the auto accompaniment.
SYNC­START
STOP
ENDING rit.
INTRO/
START/
r Press and release a single note on the key-
board to play a chord.
Continue pressing the same key each time you want a new chord to be played.
Accompaniment
section
t Play the melody with your right hand as
the auto accompaniment plays.
FWD
YES
Recording your own EZ Chord banks
You can also create your own custom chord progressions, and play along with those if you like.
Want to find out more? See page 66.
Want to find out more? See page 68.
VOICE
TEMPO
MIN MAX
MASTER VOLUME
OVERALL
TRANSPOSE
TUNING
ACMP/SONG
VOLUME
METRONOME
VOLUME
ACMP
ON/OFF
STYLE
MEASURE TEMPO
DEMO START
SYNC­START
GrandPno
001
001 116
FUNCTION SONG STYLE VOICE
MAIN A
INTRO/
START/
ENDING rit.
STOP
AUTO FILL
MAIN B
Keys for playing the accompaniment
(C1 — F#2)
CHORD GUIDE
DICTIONARY SMART EZ OFF
PORTABLE GRAND
METRONOME
123
4 56
7 8
9
rest
3
0
velocity
NO
BWD
RECORD
FWD YES
1234A
1 2 3 4 5 6/CHORD
xwzzqce
Keys for entering the chord type
ONE TOUCH SETTING
SONG MEMORY
(C3 — B4)
DUAL
TOUCH
REVERB
STAND BY ON
HARMONY
PRESETUSER
B
Use these keys for the Chord Guide Dictionary function.
Keys for entering the chord root (C5 — B5)
15

Step 4 Songs

ALL
001 111
MEASURE TEMPO
SONG
1 62 3 4 5
TakeOff!
002
SONG
PF–Grand
100
001 205
MEASURE TEMPO
SongVol
SONG
1 62 3 4 5
ACMP/SONG
VOLUME
DEMO START

CCCCCDDDDDDEEEEE

ГГГГГДДДДДДЕЕЕЕЕ
Playing a song
Playing back all three songs
The PSR-225 has three Demo songs that show­case the authentic voices and dynamic accom­paniment of the instrument.
z Simultaneously press both OVERALL
▲/▼
buttons.
DEMO START
TakeOff!
ALL
SONG
MEASURE TEMPO
001 111
1 62 3 4 5
x Stop the song.
MAIN A
ACMP
ON/OFF
SYNC­START
START/
STOP
INTRO/ ENDING rit.
AUTO FILL
MAIN B
Playing back a single song
Naturally, you can also individually select and play back any of the PortaTone’s songs.
z Enter the song mode.
FUNCTION SONG STYLE
x Select a song.
123
4 56
7 8
rest
0
velocity
BWD
NO
9
c Start (and stop) the song.
MAIN A
ACMP
ON/OFF
SYNC­START
START/
STOP
INTRO/ ENDING rit.
AUTO FILL
MAIN B
3
FWD
YES
Want to find out more? See page 75.
Changing the tempo (speed) of the song
q Press one of the OVERALL
“Tempo” is shown in the display.
TEMPO
DEMO START
▲/▼
buttons until
VOICE STYLE
116
MEASURE TEMPO
001 116
Tempo
w Press the OVERALL + or - button to speed up or
slow down the tempo.
DEMO START
Want to find out more? See page 76.
Want to find out more? See page 75.
Changing the volume of the song
q Press one of the OVERALL
“SongVol” is shown in the display.
DEMO START
▲/▼
buttons until
w Press the OVERALL + or - button to raise or lower
the volume of the song.
Want to find out more? See page 78.
16
Step 4


CCCCCCDDDDD
EEEEE


ГГГГГГДДДДД
ЕЕЕЕЕ
Songs
Recording your own song
The PSR-225 lets you record your own songs by using two different methods — Realtime and Step. Try out both of these recording methods yourself...
1 Select the desired
recording mode by pressing the RECORD button.
RECORD
zq
w
MIN MAX
MASTER VOLUME
Realtime recording Step recording
This method is much like using a conventional tape recorder, letting you play and record the parts of the song in real time.
VOICE
TEMPO
METRONOME
OVERALL
TRANSPOSE
TUNING
ACMP/SONG
VOLUME VOLUME
ACMP
ON/OFF
STYLE
MEASURE TEMPO
DEMO START
SYNC­START
GrandPno
001
001 116
FUNCTION SONG STYLE VOICE
MAIN A
INTRO/
START/
ENDING rit.
STOP
AUTO FILL
MAIN B
CHORD GUIDE
DICTIONARY SMART EZ OFF
wterzxcx
123
4 56
7 8
BWD
NO
RECORD
This method is similar to using a pencil and paper to write down each note, entering the parts of the song step by step.
Want to find out more? See pages 79-90.
PORTABLE GRAND
METRONOME
A
B
9
rest
3
0
velocity
FWD
YES
ONE TOUCH SETTING
1234A
1 2 3 4 5 6/CHORD
SONG MEMORY
1
Creating your own custom One Touch Settings
DUAL
TOUCH
REVERB
STAND BY ON
HARMONY
PRESETUSER
B
You can also create your own One Touch Settings — letting you completely reconfigure virtually all PortaTone settings at the touch of a button! Up to 16 settings can be saved (4 User banks x 4 User buttons).
q Make all desired settings on the PortaTone. w Select the User One Touch Setting
t Turn off the User One Touch Setting record
mode.
record mode.
Calling up a User One Touch Setting
STYLE
RECORD
e Select the desired User
bank (1 - 4).
STYLE
UserBank
2
r Select the desired User
button (USER 1 - 4).
1234A
OTS User
1
RECORD
123
4 56
7 8
BWD
NO
ONE TOUCH SETTING
rest
0
velocity
A Select Function #41, and select the desired bank
(1 - 4).
STYLE
FUNCTION
9
3
FWD
YES
PRESETUSER
B
B Press the appropriate USER button (1 - 4) to
instantly call up your custom panel settings.
1234A
UserBank
F41
ONE TOUCH SETTING
PRESETUSER
B
Want to find out more? See page 72.
17

Step 5 Function Parameters

1
M.Octave
STYLE
FUNCTION
T

CCCCCDDDDDDEEEEE

ГГГГГДДДДДДЕЕЕЕЕ
Using the Function parameters
The PSR-225 has a variety of settings in the Function parameters. These give you detailed control over many of the PSR-225’s features.
z Press the FUNCTION button.
FUNCTION SONG STYLE VOICE
x Select a Function number.
For a list of functions, see page 19.
STYLE
FUNCTION
The Function number can be selected while the “FUNCTION” indication is flashing.
123
4 56
BWD
NO
7 8
velocity
9
rest
3
0
FWD
YES
Enter the Function number on the numeric keypad.
M.Octave
F02
FUNCTION SONG S
Press the FUNCTION button; each press advances through the numbers. Hold down the button to continuously advance through the numbers.
c After “FUNCTION” in the display stops
flashing, change the value or setting.
After a couple of seconds, the “FUNCTION” indication stops flashing and remains lit. At the same time, the Function number (“F02” in the example above) changes automatically to the current value of the Function param­eter.
STYLE
FUNCTION
Current value of the selected Function parameter.
M.Octave
0
v Use the numeric keypad to change the
value or setting. For on/off settings, use the +/- buttons.
123
4 56
7 8
BWD
NO
velocity
9
rest
3
0
FWD
YES
VOICE
TEMPO
STYLE
GrandPno
MEASURE TEMPO
DEMO START
SYNC­START
001
001 116
FUNCTION SONG STYLE VOICE
INTRO/
START/
ENDING rit.
STOP
MIN MAX
MASTER VOLUME
OVERALL
TRANSPOSE
TUNING
ACMP/SONG
VOLUME
METRONOME
VOLUME
ACMP
ON/OFF
zx v
18
MAIN A
AUTO FILL
MAIN B
CHORD GUIDE
DICTIONARY SMART EZ OFF
PORTABLE GRAND
METRONOME
123
4 56
7 8
9
rest
3
0
velocity
NO
BWD
RECORD
FWD
YES
1234A
1 2 3 4 5 6/CHORD
ONE TOUCH SETTING
SONG MEMORY
Want to find out more? See page 30.
DUAL
TOUCH
REVERB
STAND BY ON
HARMONY
PRESETUSER
B
Step 5


CCCCCCDDDDD
EEEEE


ГГГГГГДДДДД
ЕЕЕЕЕ
Function Parameters
Function Parameters List
Function
page
F01 M.Volume Main Voice Volume 31
F02 M.Octave Main Voice Octave 31
F03 M.Pan Main Voice Pan 31
F04 M.RevLvl Main Voice Reverb Send Level 31
F05 M.ChoLvl Main Voice Chorus Send Level 31
F06 M.DspLvl Main Voice DSP Effect Send Level 31
F11 D.Volume Dual Voice Volume 35
F12 D.Octave Dual Voice Octave 35
F13 D.Pan Dual Voice Pan 35
F14 D.RevLvl Dual Voice Reverb Send Level 35
F15 D.ChoLvl Dual Voice Chorus Send Level 35
F16 D.DspLvl Dual Voice DSP Effect Send Level 35
F17 D.Voice Dual Voice 35
Function
page
F31 Reverb Reverb On/Off 44
F32 RevType Reverb Type 44
F33 Chorus Chorus On/Off 44
F34 ChoType Chorus Type 44
F35 Dsp DSP On/Off 44
F36 DspType DSP Type 44
F37 Harmony Harmony On/Off 44
F38 HarmType Harmony Type 44
F39 HarmVol Harmony Volume 44
F41 UserBank One Touch Setting User Bank 73
F51 AcmpSPnt Accompaniment Split Point 59
F61 USng1Clr User Song 1 Clear 90
F62 USng2Clr User Song 2 Clear 90
F18 Dual Dual On/Off 35
F21 S.Volume Split Voice Volume 37
F22 S.Octave Split Voice Octave 37
F23 S.Pan Split Voice Pan 37
F24 S.RevLvl Split Voice Reverb Send Level 37
F25 S.ChoLvl Split Voice Chorus Send Level 37
F26 S.DspLvl Split Voice DSP Effect Send Level 37
F27 S.Voice Split Voice 37
F28 Split Split On/Off 37
F29 SplitPnt Split Point 37
F63 USng3Clr User Song 3 Clear 90
F71 FootSw Footswitch 92
F72 VoiceSet Voice Set 39
F73 TouchSns Touch Sensitivity 39
F81 RemoteCh Remote Channel 97
F82 KbdOut Keyboard Out 97
F83 AcmpOut Accompaniment Out 97
F84 Local Local On/Off 97
F85 ExtClock External Clock 98
F86 BulkSend Bulk Data Send 98,99
F87 InitSend Initial Data Send
98,102
19

Step 6 MIDI


CCCCCDDDDDDEEEEE

ГГГГГДДДДДДЕЕЕЕЕ
Using MIDI
The PSR-225 also features rear panel MIDI terminals (MIDI IN and MIDI OUT) as well as a comprehensive set of MIDI functions, that let you use the instrument in a variety of record­ing and performance applications.
Sending original song and One Touch Setting data to another PSR-225.
MIDI transmit
PSR-225 PSR-225
MIDI receive
MIDI INMIDI OUT
MIDI OUTMIDI IN
See “Using Bulk Dump Send to Save Data“ on pages 99 - 102.
Using the MDF3 MIDI Data Filer to store and recall original PSR-225 data.
MIDI transmit
PSR-225
MIDI receive
Save/load data
MIDI INMIDI OUT
MIDI OUTMIDI IN
MDF3
See “Using Bulk Dump Send to Save Data“ on pages 99 - 102.
Playing back multi-track song data (up to 16 channels) on the PSR-225.
Set Remote Channel (page 97) to “off.”
PSR-225
Available disks
See page 97.
20
MIDI receive
MIDI OUTMIDI IN
MDF3, QY700, or computer with sequencing software.
Floppy disk with GM song data.
Step 6


CCCCCCDDDDD
EEEEE


ГГГГГГДДДДД
ЕЕЕЕЕ
MIDI
Controlling the PSR-225 with a MIDI keyboard controller (not having a tone generator)
(Auto accompaniment can also be used in this setup.)
MIDI receive
PSR-225
MIDI OUTMIDI IN
MIDI keyboard with no tone
generator
See page 97.
In this setup you can record your PSR-225 performance, including the auto accompani-
ment, to a connected computer or sequencer. (Up to 16 channels can be used.) You can then edit the recorded data on the computer or sequencer, and play it back using the sounds of the PSR-225.
Arrange and edit the data on the computer/sequencer.
MIDI transmit
PSR-225
MIDI receive
(playback)
See page 95. See “Using Initial Setup Send with a Sequencer” on page 102.
MIDI INMIDI OUT
MIDI OUTMIDI IN
Computer with sequencing software.
When using a personal computer, special software (sequencer software) is needed.
GM System Level 1
“GM System Level 1” is an addition to the MIDI standard which ensures that any GM-
compatible music data can be accurately played by any GM-compatible tone generator,
regardless of manufacturer. The GM mark is affixed to all software and hardware products
that support GM System Level 1. The PSR-225 supports GM System Level 1.
21

PANEL DISPLAY INDICATIONS

0
0
The PortaTone features a large multi-function display that shows all important settings for the instrument. The section below briefly explains the various icons and indications in the display.
A Mode indicators
B Overall functions bar indicator
J Accompaniment On indicator
TEMPO
TRANSPOSE
TUNING
ACMP/SONG
VOLUME
METRONOME
VOLUME
OVERALL
D Keyboard
A
Mode indicators
These indicate the currently selected mode — Voice, Style, Song, or Function — with the mode name encircled in a rounded rectangle. When “STYLE” or “SONG” appear without the rect­angle, the corresponding mode is active in the background.
In the first example, the Style mode is selected.
STYLE
VOICE STYLE
001
ACMP ON
MEASURE TEMPO
001 116
1 CHORD2 3
E Measure and
Tempo
K Song track indicators
0
In the second example, the Voice mode has been selected, but the Style mode is still active in the background. (This means that the style controls are active and can be used to play the currently selected style.)
H Song/Voice/Style name and number
GrandPno
C Notation
B Overall functions bar indicator
The PortaTone has five Overall functions or controls. The currently selected function is indicated by a dark bar that appears next to its name (printed on the panel).
C Notation D Keyboard
These two portions of the display conveniently indicate notes. When a user song (with chords) is being played back, they show the chord notes in succession. When the Style mode and auto accompaniment are active, the display also shows the specific notes of the current chord.
For a few specific chords, not all notes may be shown in the notation section of the display. This is due to space limitations in the display.
F Beat indicators
G Chord
I Icon window
VOICE STYLE
0
22
PANEL DISPLAY INDICATIONS
E Measure and Tempo
These show the current measure during play­back of a song or style, and the currently set Tempo value for the song or style.
F Beat indicators
These dark bars (one large, three small) flash in sequence and in time with the song or style. The large bar indicates the first beat of the measure. (See page 77.)
G Chord
When a user song (with chords) is being played back, this indicates the current chord root and type. It also indicates chords played in the ACMP section of the keyboard when the Style mode and auto accompaniment are on.
H Song/Voice/Style name and number
This portion of the display indicates the name and number of the currently selected song, voice, or style. It also displays the name and current value or setting of the Overall functions and the Function parameters, as well as other important operation messages.
I Icon window
Depending on the mode or function selected, this displays various symbols (icons) and other messages to provide convenient, at-a-glance information about the PortaTone operation. For example, when a song or style accompaniment is playing, this displays the level of each instru­mental track.
J Accompaniment On indicator
This appears when the auto accompaniment has been turned on. (See page 52.)
K Song track indicators
In song recording and playback, these indicate the status of the tracks. (See pages 75, 83.)

Music Stand

Insert the bottom edge of the included music stand into the slot located at the top rear of the PortaTone control panel.
23

PORTABLE GRAND

DEMO START
This convenient function lets you automatically exit from any other mode or function and instantly call up the Grand Piano voice.

PLAYING THE PORTABLE GRAND

Press the PORTABLE GRAND button.
PORTABLE GRAND
METRONOME
Doing this automatically cancels any other mode or function, and resets the entire instrument for playing the special “Stereo Sampling Piano” Grand Piano voice (voice 001). It automatically selects the Voice mode (with the Style mode active), and calls up style #91 (Rock Ballad). It also resets the footswitch to Sustain operation.
“STEREO SAMPLING PIANO”
The Portable Grand setting is designed also for playing with the special Pianist styles (#91 - #100). When auto accompaniment is turned on, these provide piano-only accompaniment in a variety of music styles. (See page
52.)

USING THE METRONOME

1 Set the desired tempo with the Tempo function in
the Overall menu.
Press one of the OVERALL ▲/▼ buttons, repeatedly if necessary, until “Tempo” appears in the display.
Indicates Tempo is selected
TEMPO
VOICE STYLE
Current Tempo value
116
Tempo
24
PORTABLE GRAN D
PORTABLE GRAND
METRONOME
2 Change the value.
Use the OVERALL +/- buttons to increase or decrease the Tempo value. Holding down either button continuously increases or decreases the value.
Increases Tempo value
DEMO START
Decreases Tempo value
3 Turn on the Metronome.
Press the METRONOME button.
TEMPO
3 063
To turn the Metronome off, press the METRONOME button again.
The numeric keypad cannot be used to change values for the Overall menu settings.
TEMPO
3 063

Setting the Metronome Time Signature

The time signature of the Metronome can be set to various quarter-note based meters.
The time signature changes automatically when a style or song is selected.
Simultaneously hold down the METRONOME button and press the button on the numeric keypad that corresponds to the desired time signature (see chart at right).
Number Time button signature
1 1/4 — Plays only “1” beats (all high clicks) 2 2/4 3 3/4 4 4/4 5 5/4 6 6/4 7 7/4 8 8/4 9 9/4 0 Plays no “1” beats (all low clicks)
TEMPO
3 063
Indicates current beat number
25
PORTAB LE GRAND

Adjusting the Metronome Volume

You can adjust the volume of the Metronome sound independently of the other PortaTone sounds. The volume range is 000 - 127.
1 Select the Metronome Volume function in the Overall menu.
Press one of the OVERALL ▲/▼ buttons, repeatedly if necessary, until “MtrVol” appears in the display.
Current Metronome Volume value
VOICE
DEMO START
METRONOME
VOLUME
STYLE
MEASURE
001 063
Indicates Metronome Volume is selected
MtrVol
100
TEMPO
2 Change the value.
Use the OVERALL +/- buttons to increase or decrease the Metronome Volume value. Holding down either button continuously increases or decreases the value.
Increases Metronome Volume value
DEMO START
Decreases Metronome Volume value
Restoring the Default Metronome Volume Value To restore the default Metronome Volume value (100), press both OVERALL +/- buttons simultaneously (when Metronome Volume is selected in the Overall menu).
26
PLAYING VOICES — THE VOICE MODE
The Voice mode features 228 authentic voices (including 128 General MIDI voices), plus 10 special drum kits — all of which have been created with Yamaha’s sophisticated AWM (Advanced Wave Memory) tone generation system. The Voice mode gives you many powerful and versatile tools for playing and enhancing these Voices.
The voices are divided into various instrument categories, all of which are printed on the panel for convenience. For a complete list of the available voices, see page 109.
The Voice mode is actually divided into three separate modes: Main, Dual and Split. In the Main Voice mode (see below), you can play a single voice over the entire range of the key­board. The Dual Voice mode (page 34) allows you to “layer” two different voices together for rich, complex sounds. The Split Voice mode (page 36) lets you set up two different voices for playing from separate sections of the keyboard. Moreover, each mode features special effect sections that let you enhance the sound of the Voice or Voices. These include Reverb, Chorus,
and Harmony, as well as a “DSP” section that provides miscellaneous effects such as tremolo, echo, delay, distortion, equalization, and wah. (See page 40.) Other voice-related functions include Voice Set (page 38), which lets you automatically call up the ideal settings for each voice, and Touch Sensitivity (page 38), which determines how the voices respond to your playing technique.
The PortaTone includes special Drum Kit voices — #101 - #110 — that let you play various drum and percussion sounds from the keyboard. (Refer to the Drum Kit Voice chart on page 30.) Symbols are also printed above the keyboard, conveniently indicating which sounds are played from which keys.
PLAYING A VOICE — MAIN VOICE
1 Select the Voice mode.
Press the VOICE button.
FUNCTION SONG STYLE VOICE
Indicates Voice mode is selected
VOICE
STYLE
001
GrandPno
27
PLAYI NG VOICES — THE VO ICE MODE
2 Select the desired voice number.
Use the numeric keypad. The basic categories of voices and their numbers are shown at the right side of the panel. A complete list of the available voices is given on page 109.
VOICE
PANEL V OICE
1 ~ 12 13 ~ 19 20 ~ 32 33 ~ 41 42 ~ 49 50 ~ 60 61 ~ 65
GM VOICE 111~118 119~126 127~134 135~142 143~150 151~158 159~166 167~174
PIANO MALLET ORGAN GUITAR BASS ENSEMBLE STRINGS
PIANO CHROMATIC ORGAN GUITAR BASS STRINGS ENSEMBLE BRASS
66 ~ 75 76 ~ 84 85 ~ 89 90 ~ 95 96 ~ 100
101 ~ 110
175~182 183~190 191~198 199~206 207~214 215~222 223~230 231~238
BRASS REED PIPE SYNTH LEAD SYNTH PAD DRUM KITS
REED PIPE SYNTH LEAD SYNTH PAD SYNTH EFFECTS ETHNIC PERCUSSIVE SOUND EFFECTS
There are three ways to select voices: 1) directly entering the voice number with the numeric keypad, 2) using the +/- keys to step up and down through the voices, or 3) pressing the VOICE button to advance through the voice numbers.
Using the numeric keypad
Enter the digits of the voice number as indicated on the panel. For ex­ample, to select voice #42, press “4” on the numeric keypad, then “2.”
2
13
56
4
VOICE STYLE
7 8
BWD
NO
042
ACMP ON
9
rest
3
0
velocity
FWD
YES
Aco.Bass
All two-digit voice numbers can be selected without entering an initial “0.” However, when selecting voice numbers 1 - 23, the PortaTone pauses briefly before actually calling up the voice. (This pause allows for entering three­digit voice numbers, such as “235.” Entering the numbers “2” then “4” immediately calls up voice #24, since there are no voices #240 or higher.)
If you want to immediately call up voices #1 - #23, enter one or two zeros before the number; for example, select voice #9 by pressing “0,” “0,” then “9.” Pressing only “0” does not change the voice.
28
PLAYI NG VOICES — THE VO ICE MODE
7 8
9
Using the +/- keys
Press the + key to select the next voice number, and press the - key to select the previous voice. Holding down either key continuously scrolls up or down through the numbers. The +/- keys have a “wrap around” fea­ture. For example, pressing the + key from voice #238 returns to voice #1.
rest
3
0
velocity
FWDBWD
YESNO
Using the VOICE button
Press the VOICE button to select the next voice number. (This functions exactly the same as the + button.)
FUNCTION SONG STYLE VOICE
3 Play the selected voice.
To change to another voice, repeat step 2 above.
Since either the Style or Song mode is active in the background (as indi­cated by the mode name in the display, without the rectangle), you can also play styles or songs, respectively, in the Voice mode by simply pressing the START/STOP button. The last selected style or song will be played.
Each voice is automatically called up with the most suitable octave range setting. Thus, playing middle C with one voice may sound higher or lower than another voice at the same key.
When you select a voice, the PortaTone also automati­cally calls up various settings that are appropri­ate for the voice. [This is true when Voice Set (Function #72, page 39) is set to on — the default setting.]

About Panel Voices and GM Voices

Keep in mind that the PortaTone has two separate sets of voices: 100 Panel voices and 128 GM (General MIDI) Voices. The GM Voices can also be used for optimum playback of GM-compatible song data. This means that any GM song data (played from a sequencer or other MIDI device) will sound just as the composer or programmer intended. When a GM voice is selected, the General MIDI icon appears at the top left of the display.
29
PLAYI NG VOICES — THE VO ICE MODE

Drum Kit Voice Chart (voices 101 - 110)

When one of the 10 panel Drum Kit voices are selected you can play different drums and percussion instruments on the keyboard. The drums and percussion instruments played by the various keys are marked by symbols above the keys.
VOICE
STYLE
101
Std.Kit1
No. Name LCD 101 Standard Kit 1 Std.Kit1 102 Standard Kit 2 Std.Kit2 103 Room Kit Room Kit 104 Rock Kit Rock Kit 105 Electronic Kit Elct.Kit 106 Analog Kit AnlogKit 107 Dance Kit DanceKit 108 Jazz Kit Jazz Kit 109 Brush Kit BrushKit 110 Symphony Kit SymphKit
Function Parameters — Main Voice
The Function parameters provide additional settings for the Main voice. These settings are especially useful when using a second voice in the Dual or Split modes, since they let you change or enhance the sound of the Main voice separate from the Dual or Split voice. These settings include:
• Volume
• Octave
• Pan
• Reverb Send Level
• Chorus Send Level
• DSP Effect Send Level
1 Select the Function mode.
Press the FUNCTION button.
Flashes to indicate Function parameter can be selected.
FUNCTION SONG STYLE VOICE
STYLE
FUNCTION
MEASURE TEMPO
F01
001 116
M.Volume
2 Select the desired Function parameter number.
While the “FUNCTION” indication is flashing, use the numeric key­pad to select the desired Main Voice Function parameter number (1 -
6). (See the “Parameters” list below for details.)
Function parameter numbers can be selected in the same way as with the voices (see page 28). You can use the numeric keypad to directly enter the number, use the +/- keys to step up and down through the parameters, or press the FUNCTION button to advance through the parameter numbers.
Since the “FUNCTION” indication flashes for only a couple of seconds, make sure to select the parameter quickly after step 1 above.
30
Loading...
+ 91 hidden pages