Yamaha Audio NS-35E User Manual

Read these precautions carefully before using your speaker.

●

Any time you note distortion, reduce the volume control on your
amplifier to a lower setting. Never allow your amplifier to be
driven into “clipping”. Otherwise the speaker may be damaged.

●

When using an amplifier with a rated output power higher than
the nominal input power of the speaker, care should be taken
never to exceed the speaker’s maximum input.

●

Do not attempt to clean the speaker with chemical solvents as
this might damage the finish. To clean, wipe with a dry, soft cloth.

●

To prevent the enclosure from warping or discoloring, do not
place the speaker where it will be exposed to direct sunlight or
excessive humidity.

●

Do not place the speaker where it is liable to be knocked over or
struck by falling objects. Stable placement will also ensure better
sound performance.

●

Placing the speakers on the same shelf or rack as the turntable
can result in feedback.

●

Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused by
improper placement or installation of the speaker.

N S -3 5 E

GTR

Speaker System

Thank you for selecting this YAMAHA NS-35E speaker system.

PRECAUTIONS

OWNER’S MANUAL

English

PLACING THE SPEAKERS

●

Place the speakers on a sturdy, vibration-free surface.

●

Better stereo images will be obtained when the speakers are
slightly angled in towards the listeners.

■ Using as main speakers in a multi channel
system

Position the speakers on both sides of the TV. The positioning of
speakers is important, because it controls the whole sound quality
of a multi channel system. Set up the speakers on the basis of your
listening position by following the owner’s manual supplied with
your amplifier.

Note
Because these speakers are not a magnetically shielded type,
there may be some influence on a TV picture depending on the
type of TV or the placement of the speakers. In such a case,
place the speakers apart from the TV.

Subwoofer

Front Effect
Speakers

NS-35E
(Main R)

Center

Rear Speakers

NS-35E
(Main L)

CONNECTIONS TO YOUR AMPLIFIER

Before making connections, make sure that the amplifier is
switched off.

V585580

The front cover is fastened to the enclosure at four points, and can
be removed if desired. To remove the cover, hold on to both sides
and slowly pull straight away from the speaker. To reattach, line up
the four pegs on the inside surface of the cover with the four
corresponding holes on the speaker and push gently.

Note
When the cover is removed, take care not to touch the speaker
units with your hands or to exert excessive force with tools.

REMOVING THE FRONT COVER

Speaker (R)

Speaker (L)

Tighten

Loosen

Red (+)

Red

Amplifier

Speakers output
terminals of the
amplifier

Black (–)

■ Connections

●

Connect the screw-type input terminals at the rear of the
speakers to the speaker output terminals of your amplifier with
the provided speaker cables.

●

One side of the speaker cable is red and the other side is black.
Connect the (+) terminals on both the amplifier and the speakers
using this red side. Connect the (–) terminals on both
components using the black side of the cable.

●

Connect one speaker to the left (marked L) terminals of your
amplifier, and another speaker to the right (marked R) terminals,
making sure not to reverse the polarity (+, –). If one speaker is
connected with reversed polarity, the sound will be unnatural and
lack bass.

Procedure:

➀

Loosen the terminal knob.

➁

Remove approx. 10 mm insulation from the speaker cable and
insert the bare wire end properly into the terminal hole.

➂

Tighten the knob.

➃

Test the security of the connection by tugging lightly on the
cable at the terminal.

Note
Do not let the bare speaker wires touch each other as this
could damage the speaker and/or the amplifier.

Type ........................................... 2-way bass reflex speaker system

Driver..................................................................16 cm cone woofer

3 cm dome tweeter

Impedance ........................................................................... 6 ohms

Frequency Response ...............................................50 Hz – 30 kHz

Nominal Input Power................................................................ 60 W

Maximum Input Power ........................................................... 150 W

Sensitivity ................................................................ 90 dB/2.83 V/m

Crossover Frequency.............................................................. 3 kHz

Dimensions (W x H x D)...................................233 x 392 x 275 mm

Weight .................................................................................... 6.3 kg

Accessories................................................ Speaker cable (4 m) x 2

●

Specifications subject to change without notice due to product
improvements.

●

Care should be taken not to exceed the input power values
noted above.

SPECIFICATIONS